Validation of a 3D damage model for predicting the response of composite structures under crushing loads

A 3D intralaminar continuum damage mechanics based material model, combining damage mode interaction and material nonlinearity, was developed to predict the damage response of composite structures undergoing crush loading. This model captures the structural response without the need for calibration of experimentally determined material parameters. When used in the design of energy absorbing composite structures, it can reduce the dependence on physical testing. This paper validates this model against experimental data obtained from the literature and in-house testing. Results show that the model can predict the force response of the crushed composite structures with good accuracy. The simulated energy absorption in each test case was within 12% of the experimental value. Post-crush deformation and the damage morphologies, such as ply splitting, splaying and breakage, were also accurately reproduced. This study establishes the capability of this damage model for predicting the responses of composite structures under crushing loads.

Intelligent management of end consumers loads including electric vehicles through a SCADA system

The large penetration of intermittent resources, such as solar and wind generation, involves the use of storage systems in order to improve power system operation. Electric Vehicles (EVs) with gridable capability (V2G) can operate as a means for storing energy. This paper proposes an algorithm to be included in a SCADA (Supervisory Control and Data Acquisition) system, which performs an intelligent management of three types of consumers: domestic, commercial and industrial, that includes the joint management of loads and the charge/discharge of EVs batteries. The proposed methodology has been implemented in a SCADA system developed by the authors of this paper – the SCADA House Intelligent Management (SHIM). Any event in the system, such as a Demand Response (DR) event, triggers the use of an optimization algorithm that performs the optimal energy resources scheduling (including loads and EVs), taking into account the priorities of each load defined by the installation users. A case study considering a specific consumer with several loads and EVs is presented in this paper.

Problemática associada à utilização de diferentes tipos de mochila para transporte de material escolar

O transporte de cargas é uma tarefa comum para crianças, adolescentes e adultos, pela necessidade de transferência diária de objetos pessoais, livros e artigos de papelaria para os locais de trabalho ou escolas. Diversos autores apontam que o peso carregado durante transporte de material é o principal responsável pelo aparecimento de dor lombar. Deste modo é importante o constante estudo da temática para a definição recomendações e limites. O presente estudo teve como principais objetivos a caraterização da problemática associada à utilização de mochilas e a determinação do Peso Máximo Aceitável (PMA) e do Índice de Esforço Percebido (IEP) para a tarefa de transporte de mochilas, através da abordagem psicofísica. O estudo foi desenvolvido com estudantes do 7º, 8º e 9º ano de escolaridade e, foi dividido em duas fases. Na 1ª fase foram aplicados questionários para a análise da problemática associada à utilização de diferentes tipos de mochilas escolares. Nesta fase, foram incluídos aspetos associados à identificação do tipo de mochila mais utilizada, as rotinas e hábitos dos estudantes e as características da mochila utilizada. Verificou-se que os estudantes utilizam, maioritariamente, a mochila de duas alças para transporte de material escolar. Posteriormente foram efetuadas medições de peso da mochila, altura e peso aos 131 estudantes que constituíram a amostra da 1º fase. O principal objetivo deste ponto foi identificar o tipo de mochila habitualmente utilizada pelos estudantes assim como, o peso transportado nas mochilas. Na 2ª fase foi efetuado um estudo para a determinação do PMA e do IEP, através da abordagem psicofísica, para a tarefa de transporte de mochila, considerando-se uma amostra constituída por 10 estudantes. Para este estudo, apenas foi considerada a mochila mais frequentemente utilizada, identificada na 1º fase. A tarefa consistiu no transporte da mochila nos dois ombros e com as alças devidamente ajustadas ao corpo, num percurso pré-definido, de acordo com o procedimento experimental. Os resultados indicaram que nem todos os estudantes transportam mochilas com pesos dentro das recomendações da Organização Mundial de Saúde. O PMA determinado pelos estudantes foi de 6.8 kg para a mochila de duas alças e a região dos ombros foi identificada durante todo o estudo como sendo a que apresentava maior intensidade de dor durante o transporte da mochila.

Novel LTCC-potentiometric microfluidic device for biparametric analysis of organic compounds carrying plastic antibodies as ionophores: Application to sulfamethoxazole and trimethoprim

Monitoring organic environmental contaminants is of crucial importance to ensure public health. This requires simple, portable and robust devices to carry out on-site analysis. For this purpose, a low-temperature co-fired ceramics (LTCC) microfluidic potentiometric device (LTCC/μPOT) was developed for the first time for an organic compound: sulfamethoxazole (SMX). Sensory materials relied on newly designed plastic antibodies. Sol–gel, self-assembling monolayer and molecular-imprinting techniques were merged for this purpose. Silica beads were amine-modified and linked to SMX via glutaraldehyde modification. Condensation polymerization was conducted around SMX to fill the vacant spaces. SMX was removed after, leaving behind imprinted sites of complementary shape. The obtained particles were used as ionophores in plasticized PVC membranes. The most suitable membrane composition was selected in steady-state assays. Its suitability to flow analysis was verified in flow-injection studies with regular tubular electrodes. The LTCC/μPOT device integrated a bidimensional mixer, an embedded reference electrode based on Ag/AgCl and an Ag-based contact screen-printed under a micromachined cavity of 600 μm depth. The sensing membranes were deposited over this contact and acted as indicating electrodes. Under optimum conditions, the SMX sensor displayed slopes of about −58.7 mV/decade in a range from 12.7 to 250 μg/mL, providing a detection limit of 3.85 μg/mL and a sampling throughput of 36 samples/h with a reagent consumption of 3.3 mL per sample. The system was adjusted later to multiple analyte detection by including a second potentiometric cell on the LTCC/μPOT device. No additional reference electrode was required. This concept was applied to Trimethoprim (TMP), always administered concomitantly with sulphonamide drugs, and tested in fish-farming waters. The biparametric microanalyzer displayed Nernstian behaviour, with average slopes −54.7 (SMX) and +57.8 (TMP) mV/decade. To demonstrate the microanalyzer capabilities for real applications, it was successfully applied to single and simultaneous determination of SMX and TMP in aquaculture waters.

Very low prevalence of meticillin-resistant Staphylococcus aureus carrying the mecC gene in western Switzerland.

We report the first case of meticillin-resistant Staphylococcus aureus (MRSA) with the mecC gene in a patient in western Switzerland. After this first identification, a polymerase chain reaction protocol was established to investigate the occurrence of this new mecC gene in the population of this region. Enrichment broths were investigated from 1062 patients screened for MRSA, meticillin-susceptible Staphylococcus aureus isolates from clinical specimens from 475 patients, and 80 MRSA isolates (from 2005 to 2011) showing discrepancies between genotypic and phenotypic meticillin resistance. None was positive for mecC, suggesting that it is rare in the patient population of this region.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Carrying the Boat to the Dock

Lisa Tiffeny

Place Card - Girl Carrying Hat Boxes

A place card with an illustration of the back of a girl as she carries two hat boxes.

List of the number of loads dredged by Smiley’s Dredge since the 1st of October along the Welland Railway

List of the number of loads dredged by Smiley’s Dredge since the 1st of October along the Welland Railway. This is addressed to S.D. Woodruff and signed by James Woodall of Lock No. 1. There are holes and stains in the document. Text is not affected, Jan. 12, 1859.

Age and species related variation in the development of growth plates of the knee and implications for the locomotion of Australopithecus afarensis

Comprendre l'évolution de la bipédie est un élément essentiel à la recherche en paléoanthropologie, car ce comportement est le trait le plus important utilisé pour identifier les fossiles comme appartenant à la lignée des hominines. La topographie de la surface infradiaphysaire du fémur et du tibia pourrait donner un aperçu du comportement locomoteur des espèces fossiles, mais n'a pas été étudiée de façon approfondie. Ce trait reflète directement les différences dans la locomotion, puisque la surface change de topographie pour mieux résister aux charges encourues par les mouvements réguliers. Le plan infradiaphysaire du fémur chez les humain est relativement plat, tandis que la surface est plus irrégulière chez les grands singes. Dans ce projet, les métaphyses du genou ont été étudiées d’une manière quantifiée afin de percevoir les différences entre espèces et mieux comprendre le développement ontogénique de ces traits. Les angles formés par les protrusions et les creux de ces surfaces ont été mesurés à partir de points de repère enregistrés en trois-dimensions sur les métaphyses du genou chez les humains, chimpanzés, gorilles, et orangs-outans, et chez trois fossiles Australopithecus afarensis, afin d’observer de l’effet de facteurs tel le stade de croissance et l’appartenance à une espèce sur la topographie des plaques de croissance du genou. Les angles d’obliquité du fémur et du tibia ont aussi été mesurés et analysés. Les résultats ont révélé que le stade développemental et l’appartenance à une espèce et, par association, le mode de locomotion, ont un effet significatif sur les métaphyses du genou. Il a également été constaté que les mesures d'Australopithecus afarensis chevauchent les valeurs trouvées chez les humains et chez les grands singes, ce qui suggère que cette espèce avait possiblement conservé une composante arboricole dans son comportement locomoteur habituel.

Potential use of a recombinant replication-defective adenovirus vector carrying the C-terminal portion of the P97 adhesin protein as a vaccine against Mycoplasma hyopneumoniae in swine.

Mycoplasma hyopneumoniae causes severe economic losses to the swine industry worldwide and the prevention of its related disease, enzootic porcine pneumonia, remains a challenge. The P97 adhesin protein of M. hyopneumoniae should be a good candidate for the development of a subunit vaccine because antibodies produced against P97 could prevent the adhesion of the pathogen to the respiratory epithelial cells in vitro. In the present study, a P97 recombinant replication-defective adenovirus (rAdP97c) subunit vaccine efficiency was evaluated in pigs. The rAdP97c vaccine was found to induce both strong P97 specific humoral and cellular immune responses. The rAdP97c vaccinated pigs developed a lower amount of macroscopic lung lesions (18.5 ± 9.6%) compared to the unvaccinated and challenged animals (45.8 ± 11.5%). rAdP97c vaccine reduced significantly the severity of inflammatory response and the amount of M. hyopneumoniae in the respiratory tract. Furthermore, the average daily weight gain was slightly improved in the rAdP97c vaccinated pigs (0.672 ± 0.068 kg/day) compared to the unvaccinated and challenged animals (0.568 ± 0.104 kg/day). A bacterin-based commercial vaccine (Suvaxyn® MH-one) was more efficient to induce a protective immune response than rAdP97c even if it did not evoke a P97 specific immune response. These results suggest that immunodominant antigens other than P97 adhesin are also important in the induction of a protective immune response and should be taken into account in the future development of M. hyopneumoniae subunit vaccines.

Relativistic atomic level calculations with nuclei carrying additional fractional charges

One-electron energy levels and wavelengths have been calculated for Na-like ions whose nuclei carry quarks with additional charges ±e/3, ±2e/3. The calculations are based on relativistic self-consistent field procedures. The deviations from experimental values exhibit regularities which allow an extrapolation for the wavelengths of 3s - 3p, 3s - 4p, 3p - 3d, and 3p - 4s transitions for the nuclear charge Z = 11± 1/3, ±2/3. A number of transitions are found in the region of visible light which could be used in an optical search for quark atoms.

Heavy metal and microbial loads in sewage irrigated vegetables of Kabul, Afghanistan

Little is known about the heavy metal and microbial contamination of vegetables produced in Central Asian cities. We therefore measured the concentration of cadmium (Cd), copper (Cu), lead (Pb), and zinc (Zn) and of faecal pathogens (Coliform bacteria, Salmonella sp., Shigella sp., Ascaris lubricoides, Entamoeba sp. and pinworms [Oxyuris vermicularis syn. Enterobius vermicularis]) in soil, irrigation water, and marketed vegetables of Kabul City, Afghanistan. Leaf Pb and Zn concentrations of leafy vegetables were with 1–5 and 33–160 mg kg^{-1} dry weight (DW) several-fold above respective international thresholds of 0.3 mg Pb kg^{-1} and 50 mg Zn kg^{-1}. The tissue concentration of Cu was below threshold limits in all samples except for spinach in one farm. Above-threshold loads of microbes and parasites on vegetables were found in five out of six gardens with coliforms ranging from 0.5–2 × 10^7 cells 100g^{-1} fresh weight (FW), but no Salmonella and Shigella were found. Contamination with 0.2 × 10^7 eggs 100g^{-1} FW of Ascaris was detected on produce of three farms and critical concentrations of Entamoeba in a single case, while Oxyuris vermicularis, and Enterobius vermicularis were found on produce of three and four farms, respectively. Irrigation water had Ascaris, Coliforms, Salmonella, Shigella, Entamoeba, and Oxyuris vermicularis syn. Enterobius vermicularis ranging from 0.35 × 10^7 to 2 × 10^7 cells l^{-1}. The heavy metal and microbial loads on fresh UPA vegetables are likely the result of contamination from rising traffic, residues of the past decades of war and lacking treatment of sewage which needs urgent attention.

Exercises in reacting to sensory imagery and words carrying emotional overtones

This paper contains an outline of study for hearing impaired children to help them learn how to form and react to sensory imagery.