Design and flight testing of an integrated solar powered UAV and WSN for greenhouse gas monitoring emissions in agricultural farms

There is an increased interest in measuring the amount of greenhouse gases produced by farming practices . This paper describes an integrated solar powered Unmanned Air Vehicles (UAV) and Wireless Sensor Network (WSN) gas sensing system for greenhouse gas emissions in agricultural lands. The system uses a generic gas sensing system for CH4 and CO2 concentrations using metal oxide (MoX) and non-dispersive infrared sensors, and a new solar cell encapsulation method to power the unmanned aerial system (UAS)as well as a data management platform to store, analyze and share the information with operators and external users. The system was successfully field tested at ground and low altitudes, collecting, storing and transmitting data in real time to a central node for analysis and 3D mapping. The system can be used in a wide range of outdoor applications at a relatively low operational cost. In particular, agricultural environments are increasingly subject to emissions mitigation policies. Accurate measurements of CH4 and CO2 with its temporal and spatial variability can provide farm managers key information to plan agricultural practices. A video of the bench and flight test performed can be seen in the following link: https://www.youtube.com/watch?v=Bwas7stYIxQ

Initial prototype testing of Ray's Night Out: A new mobile app targeting risky drinking in young people

Background Risky single occasion drinking (RSOD; 4 or more drinks in <6 h) more than doubles the risk of injury in young people (15 - 25 years). The potential role of smartphone apps in reducing RSOD in young people is yet to be explored. Objective: To describe the initial prototype testing of ‘Ray's Night Out’, a new iPhone app targeting RSOD in young people. Method Quantitative and qualitative methods were used to evaluate the quality, perceived utility, and acceptability of the app among nine young people (19e23 years). Results Participants reported Ray's Night Out had good to excellent levels of functionality and visual appeal, acceptable to good levels of entertainment, interest and information, and acceptable levels of customization and interactivity. Young people thought the app had high levels of youth appeal, would prompt users to think about their alcohol use limits, but was unlikely to motivate a change in alcohol use in its current form. Qualitative data provided several suggestions for improving the app. Conclusion Following revision, Ray's Night Out could provide an effective intervention for RSOD in non help-seeking young people. A randomized controlled trial is currently underway to test the final prototype of the app.

Novel Mass Spectrometric Analysis Methods for Anabolic Androgenic Steroids in Sports Drug Testing

The feasibility of different modern analytical techniques for the mass spectrometric detection of anabolic androgenic steroids (AAS) in human urine was examined in order to enhance the prevalent analytics and to find reasonable strategies for effective sports drug testing. A comparative study of the sensitivity and specificity between gas chromatography (GC) combined with low (LRMS) and high resolution mass spectrometry (HRMS) in screening of AAS was carried out with four metabolites of methandienone. Measurements were done in selected ion monitoring mode with HRMS using a mass resolution of 5000. With HRMS the detection limits were considerably lower than with LRMS, enabling detection of steroids at low 0.2-0.5 ng/ml levels. However, also with HRMS, the biological background hampered the detection of some steroids. The applicability of liquid-phase microextraction (LPME) was studied with metabolites of fluoxymesterone, 4-chlorodehydromethyltestosterone, stanozolol and danazol. Factors affecting the extraction process were studied and a novel LPME method with in-fiber silylation was developed and validated for GC/MS analysis of the danazol metabolite. The method allowed precise, selective and sensitive analysis of the metabolite and enabled simultaneous filtration, extraction, enrichment and derivatization of the analyte from urine without any other steps in sample preparation. Liquid chromatographic/tandem mass spectrometric (LC/MS/MS) methods utilizing electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) were developed and applied for detection of oxandrolone and metabolites of stanozolol and 4-chlorodehydromethyltestosterone in urine. All methods exhibited high sensitivity and specificity. ESI showed, however, the best applicability, and a LC/ESI-MS/MS method for routine screening of nine 17-alkyl-substituted AAS was thus developed enabling fast and precise measurement of all analytes with detection limits below 2 ng/ml. The potential of chemometrics to resolve complex GC/MS data was demonstrated with samples prepared for AAS screening. Acquired full scan spectral data (m/z 40-700) were processed by the OSCAR algorithm (Optimization by Stepwise Constraints of Alternating Regression). The deconvolution process was able to dig out from a GC/MS run more than the double number of components as compared with the number of visible chromatographic peaks. Severely overlapping components, as well as components hidden in the chromatographic background could be isolated successfully. All studied techniques proved to be useful analytical tools to improve detection of AAS in urine. Superiority of different procedures is, however, compound-dependent and different techniques complement each other.

From Polymorph Screening to Dissolution Testing - Solid Phase Analysis during Pharmaceutical Development and Manufacturing

Solid materials can exist in different physical structures without a change in chemical composition. This phenomenon, known as polymorphism, has several implications on pharmaceutical development and manufacturing. Various solid forms of a drug can possess different physical and chemical properties, which may affect processing characteristics and stability, as well as the performance of a drug in the human body. Therefore, knowledge and control of the solid forms is fundamental to maintain safety and high quality of pharmaceuticals. During manufacture, harsh conditions can give rise to unexpected solid phase transformations and therefore change the behavior of the drug. Traditionally, pharmaceutical production has relied on time-consuming off-line analysis of production batches and finished products. This has led to poor understanding of processes and drug products. Therefore, new powerful methods that enable real time monitoring of pharmaceuticals during manufacturing processes are greatly needed. The aim of this thesis was to apply spectroscopic techniques to solid phase analysis within different stages of drug development and manufacturing, and thus, provide a molecular level insight into the behavior of active pharmaceutical ingredients (APIs) during processing. Applications to polymorph screening and different unit operations were developed and studied. A new approach to dissolution testing, which involves simultaneous measurement of drug concentration in the dissolution medium and in-situ solid phase analysis of the dissolving sample, was introduced and studied. Solid phase analysis was successfully performed during different stages, enabling a molecular level insight into the occurring phenomena. Near-infrared (NIR) spectroscopy was utilized in screening of polymorphs and processing-induced transformations (PITs). Polymorph screening was also studied with NIR and Raman spectroscopy in tandem. Quantitative solid phase analysis during fluidized bed drying was performed with in-line NIR and Raman spectroscopy and partial least squares (PLS) regression, and different dehydration mechanisms were studied using in-situ spectroscopy and partial least squares discriminant analysis (PLS-DA). In-situ solid phase analysis with Raman spectroscopy during dissolution testing enabled analysis of dissolution as a whole, and provided a scientific explanation for changes in the dissolution rate. It was concluded that the methods applied and studied provide better process understanding and knowledge of the drug products, and therefore, a way to achieve better quality.

A Comparison of Methods for Describing Irregular Animal Growth and Testing for Treatment Effects

In many designed experiments with animals liveweight is recorded several times during the trial. Such data are commonly referred to as repeated measures data. An aim of such experiments is generally to compare the growth patterns for the applied treatments. This paper discusses some of the methods of analysing repeated measures data and illustrates the use of cubic smoothing splines to describe irregular cattle growth data. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Direct shear testing on unsaturated silty soils to investigate the effects of drying and wetting on shear strength parameters at low suction

A modified conventional direct shear device was used to measure unsaturated shear strength of two silty soils at low suction values (0 ~ 50 kPa) that were achieved by following drying and wetting paths of soil water characteristic curves (SWCCs). The results revealed that the internal friction angle of the soils was not significantly affected by either the suction or the drying wetting SWCCs. The apparent cohesion of soil increased with a decreasing rate as suction increased. Shear stress-shear displacement curves obtained from soil specimens subjected to the same net normal stress and different suction values showed a higher initial stiffness and a greater peak stress as suction increased. A soil in wetting exhibited slightly higher peak shear stress and more contractive volume change behavior than that of soil in drying at the same net normal stress and suction.

Testing threshold functions using implied minterm structure

A geometrical structure called the implied minterm structure (IMS) has been developed from the properties of minterms of a threshold function. The IMS is useful for the manual testing of linear separability of switching functions of up to six variables. This testing is done just by inspection of the plot of the function on the IMS.

Antimicrobial susceptibility testing of Brachyspira intermedia and Brachyspira pilosicoli isolates from Australian chickens

Susceptibilities of predominantly Australian isolates of the pathogenic intestinal spirochaetes Brachyspira intermedia (n=25) and Brachyspira pilosicoli (n=17) from chickens were tested in agar dilution against four concentrations each of the antimicrobials tiamulin, lincomycin, tylosin, metronidazole, tetracycline and ampicillin. Based on available minimum inhibitory concentration (MIC) breakpoint values for Brachyspira hyodysenteriae or other Gram-negative enteric veterinary pathogens, isolates of both species generally were susceptible to tiamulin, lincomycin, metronidazole and tetracycline. Although not classed as resistant, four isolates of B. intermedia had an elevated MIC range for tiamulin (1 to 4 mg/l), 11 isolates of B. intermedia and five of B. pilosicoli had an elevated MIC range for lincomycin (10 to 50 mg/l), one isolate of B. pilosicoli had an elevated MIC range for tetracycline (10 to 20 mg/l), and one isolate of B. intermedia and five of B. pilosicoli had an elevated MIC range for ampicillin (10 to 50 mg/l). A clear lack of susceptibility to tylosin (MIC >4 mg/l) was seen in 11 isolates each of B. intermedia and B. pilosicoli, and to ampicillin (MIC >32 mg/l) in two isolates of B. pilosicoli. These data suggest that some resistance to common antimicrobials exists among intestinal spirochetes obtained from laying hens and supports the need of MIC data for clinical isolates before any treatment is considered.

Measuring the traction profile on sportsfields: Equipment development and testing

Traction is recognised as an important component of the overall playability and safety of a sportsfield. It relates to the "grip", or footing, provided through an athlete's shoe when in contact with the surface, and is normally measured by the torque generated when a weighted studded disc apparatus is dropped onto the turf and twisted manually. This paper describes the development of an automated traction tester, which mechanises the dropping and twisting of the weighted studded disc. By standardising these operational stages, more repeatable and reliable results can be expected than from the original hand-operated design where positioning of the disc and speed of rotation are controlled manually and so can vary from one measurement to the next. As well as measuring the maximum torque reached during rotation of the studded disc, the automated traction tester generates a profile of torque showing changes over time and calculates the angle through which the studded disc moved before reaching maximum torque. These aspects are now covered by a utility patent (PAT/AU/2004270767). Use of the automated traction tester is illustrated by comparative data for a range of warm-season turfgrasses, by comparisons of traction under different surface conditions generated by wear on Cynodon dactylon cultivars, and by the effects of environment, management and playing patterns on traction across a multi-use sports stadium.

Optical peanut yield monitor: Development and testing

An optical peanut yield monitor was developed, fabricated, and field-tested. The overall system includes an optical mass-flow sensor, a GPS receiver, and a data acquisition system. The concept for the mass-flow sensor is based on that of the cotton yield-monitor sensor developed previously by Thomasson and Sui (2000). A modified version of the sensor was designed to be specific to peanut mass-flow measurement. Field testing of the peanut yield monitor was conducted in Australia during the May 2003 harvest. After subsequent minor modifications, the system was more extensively tested in Mississippi in October of 2003 and November of 2004. Test results showed that the output of the peanut mass-flow sensor was very strongly correlated with the harvested load weight, and the system's performance was stable and reliable during the tests.

Testing approximate theories of first-order phase transitions on the two-dimensional Potts model

The two-dimensional,q-state (q>4) Potts model is used as a testing ground for approximate theories of first-order phase transitions. In particular, the predictions of a theory analogous to the Ramakrishnan-Yussouff theory of freezing are compared with those of ordinary mean-field (Curie-Wiess) theory. It is found that the Curie-Weiss theory is a better approximation than the Ramakrishnan-Yussouff theory, even though the former neglects all fluctuations. It is shown that the Ramakrishnan-Yussouff theory overestimates the effects of fluctuations in this system. The reasons behind the failure of the Ramakrishnan-Yussouff approximation and the suitability of using the two-dimensional Potts model as a testing ground for these theories are discussed.

Rationale of Length Scale-Down Model Span Testing of Transmission Lines

Length scale-down (LS) model tests have been traditionally employed for laboratory studies on aeolian vibration of transmission line conductors. The span adopted is normally 30 m and is recommended by the relevant Indian, as well as other, standards. The traditionally adopted length of the LS model is reexamined herein to establish the rationale behind the choice. Based on the theoretical studies discussed, certain guidelines for the choice of model span of conductor are emphasized. In addition, the adequacy of the LS span as a tool for predicting the performance of the full span is reestablished.

Testing insecticides against Phthorimaea operculella (Zeller) (Lepidoptera: Gelechiidae) using a tomato plant bioassay

A bioassay technique was developed to test the efficacy of insecticides against potato moth (Phthorimaea operculella (Zeller)) on tomatoes. The technique tested efficacy against both larvae in mines and neonate larvae that had not yet penetrated the leaf, and explained the failure of some insecticides to control P. operculella infestations in commercial tomato crops. Neonate larvae placed on leaves of potted plants several days before treatment provided larvae for testing of insecticides against larvae in mines; other neonates were placed on leaves after treatment to test efficacy against larvae yet to penetrate the leaf. The plants were sprayed with the candidate insecticides, held for 5-7 days, and larval mortality assessed. Chlorfenapyr (100, 200 g a.i. ha-1) and abamectin (8.1 g a.i. ha-1) were effective against neonate larvae and larvae in mines. Sulprofos (720 g a.i. ha -1), methomyl (450 g a.i. ha-1) and spinosad (96 g a.i. ha-1) were effective against neonate larvae but not against larvae in mines. Methamidophos (1102 g a.i. ha-1), endosulfan (700 g a.i. ha-1) and Bacillus thuringiensis kurstaki (1000 g ha-1) had some effect against exposed larvae but little against larvae in mines. Thiodicarb (525 g a.i. ha-1), azinphos-ethyl (440 g a.i. ha -1), imidacloprid (59.5 g a.i. ha-1), hexaflumuron (50 g a.i. ha-1), methoxyfenozide (300 g a.i. ha-1) and tebufenozide (200 g a.i. ha-1) were ineffective. A field trial using chlorfenapyr (25, 50, 100, 150 and 200 g a.i. ha-1) and methamidophos (1102 g a.i. ha-1) validated the bioassay technique, with chlorfenapyr effective in reducing the numbers of larvae in mines in leaves.

Testing the simulation capability of APSIM-ORYZA under different levels of nitrogen fertiliser and transplanting time regimes in Korea

APSIM-ORYZA is a new functionality developed in the APSIM framework to simulate rice production while addressing management issues such as fertilisation and transplanting, which are particularly important in Korean agriculture. To validate the model for Korean rice varieties and field conditions, the measured yields and flowering times from three field experiments conducted by the Gyeonggi Agricultural Research and Extension Services (GARES) in Korea were compared against the simulated outputs for different management practices and rice varieties. Simulated yields of early-, mid- and mid-to-late-maturing varieties of rice grown in a continuous rice cropping system from 1997 to 2004 showed close agreement with the measured data. Similar results were also found for yields simulated under seven levels of nitrogen application. When different transplanting times were modelled, simulated flowering times ranged from within 3 days of the measured values for the early-maturing varieties, to up to 9 days after the measured dates for the mid- and especially mid-to-late-maturing varieties. This was associated with highly variable simulated yields which correlated poorly with the measured data. This suggests the need to accurately calibrate the photoperiod sensitivity parameters of the model for the photoperiod-sensitive rice varieties in Korea.

Development and testing of an evaluation procedure for commercial manure additive products.

Manure additive products can be used to reduce odour emissions (OE) from livestock farms. The standardised evaluation of these manure additive products under specific farm conditions is important. In this study, the efficacy of a manure additive (WonderTreat(TM), CKLS, Inc., Hong-Kong) was assessed under Australian conditions utilising a combination of laboratory and field-scale evaluation techniques. As a first step, the efficacy of the manure additive was assessed in a laboratory-scale trial using a series of uniformly managed digesters and standard odour, liquor ammonia and hydrogen sulphide concentration measurement procedures. This showed that the addition of WonderTreat(TM) at the 'low dose rate' (LDR) (102.6 g m-2) used during the trial significantly, but only marginally (30%; P = 0.02) reduced the OE rate (mean 13.9 OU m-2 s-1) of anaerobic pig liquor relative to an untreated control (UC) (19.9 OU m-2 s-1). However, the 'high dose rate' (HDR) (205.3 g m-2) also assessed during the trial preformed similarly (19.7 OU m-2 s-1) to the UC. No statistically significant difference in the concentrations of a range of measured water quality variables at the 5% level was observed between the treatments or controls digesters. As a second step, a field-scale assessment of the manure additive was undertaken at a commercial piggery. Two piggery manure lagoons (each with approximately 2500 m2 surface area) were included in the study; one was treated with WonderTreat(TM) while the other was used as control. The efficacy of the treatment was assessed using olfactometric evaluation of odour samples collected from the surface of the pond using a dynamic wind tunnel and ancillary equipment. No statistically significant reduction in OE rate could be demonstrated (P = 0.35), partially due to the limited number of samples taken during the assessment. However, there was a numerical reduction in the average OE rate of the treatment pond (29 OU m-2 s-1 at 1 m s-1) compared to the control lagoon (38 OU m-2 s-1 at 1 m s-1).