Synthesis and Characterization of Side-Chain Liquid Crystalline (M6MPP/M6NPAP) Copolymers with NLO Properties

A series of novel thermotropic side-chain liquid crystalline polymer based on polymethacrylate backbone containing electron-accepting 4-(4'-nitrophenylazo)phenoxy as nonlinear optical active group and electron-donating 4(4'-methoxyphenyl) phenoxy group as mesogen attached covalently to the backbone through the flexible spacer was prepared and characterized, respectively. The results from differential scanning calorimetry showed that these series of copolymers were enantiotropic liquid crystal with single mesophase. The melting points and the relative enthalpy change of the copolymers depressed with increasing the molar percent of 4'-nitroazobenzene monomer units over 0 similar to 50mol%, but the enthalpies change of the transition from mesophase to isotropic state increased for the copolymers containing 0 similar to 50mol% 4'-nitroambenzene units. The texture observed under polarized optical microscope identified that the copolymers containing 24molar% or more than 24mol% 4-nitroambenzene monomer units could form smectic mesophase with the focal-conic texture. The results detected by WAXD were in good agreement with the results observed by POM.

Synthesis and properties of two series of H-bonded and non-H-bonded thermotropic liquid crystal monomers

Two series of monomers, namely n-1-bromo-(4-(4-nitrophenylazo)phenyloxy]alkanes (Bn, n = 2, 3, 4, 5, 6, 8, 10) and N-n-[4-(4-nitrophenylazo)phenyloxy]alkyl diethanolamines (Cn, n = 3, 5, 6, 10), were synthesized and characterized. Their thermal behaviour was studied by differential scanning calorimetry (DSC), wide angle X-ray diffractometry (WAXD) and polarizing optical microscopy (POM) equipped with a hot stage. The results showed that the Bns (n greater than or equal to 6) exhibit monotropic nematic liquid crystalline behaviour; no liquid crystalline phase was found for the Bns (n < 6), while for the Cns, enantiotropic smectic liquid crystallinity for n = 5, 6, 10 was seen, and for n = 3 monotropic smectic phases were found. This different phase behaviour between Bn and Cn compounds is attributed to their different end groups. The FTIR analysis of Cn indicated that there exists an intermolecular hydrogen bond between hydroxy groups, so that more stable liquid crystalline phase are formed. The effect of the length of the flexible chain on the thermal behaviour is also discussed.

Synthesis of a series of chiral copolymers with azo groups and investigations of reversible liquid crystalline alignment induced by the LB films of these materials

A series of liquid crystalline copolymers, poly{2-hydroxyethyl methacrylate}-co-{6-[4-(S-2-methyl-1-butyloxycarbonylphenylazo)phenoxy]hexyl methacrylate} with an azobenzene moiety as photoreactive mesogenic unit, was prepared and investigated by using DSC, polarized optical microscopy and X-ray diffraction. The results show that these polymers exhibit smectic phases. Z-type Langmuir-Blodgett films of these copolymers were successfully deposited onto calcium fluoride and quartz. Reversible homeotropic and planar liquid crystal alignments were induced by using the photochromism of the LB films of one of the copolymers containing 20.6 mol % of the azo unit.

A SAXS study of flow alignment of thermotropic liquid crystal mixtures

We report on the capillary flow behaviour of thermotropic liquid crystal mixtures containing 4-n-octyl-4'-cyanobiphenyl (8CB) and 4-n-pentyl-4'-cyanobiphenyl (5CB). The liquid crystal mixtures are studied in the Nematic (N) and Smectic (SA) phases at room temperature. Polarised optical microscopy (POM), rheology and simultaneous X-ray diffraction (XRD)/capillary flow experiments are performed to characterise the system. Polarised optical microscopy reveals a dramatic change in optical texture when the 5CB content is increased from 20 to 30% in the mixtures. X-ray diffraction results show that the system goes through a SA-N phase transition, such that the mixtures are smectic for 10-20% 5CB and nematic for 30-90% 5CB. Smectic mixtures flow with the layers aligned along the flow direction (mesogens perpendicular to flow) while nematic mixtures flow with the mesogens aligned in the flow direction. Simultaneous XRD/shear flow experiments show that the SA-N transition is independent of the flow rate in the range 1-6 ml min-1. The correlation length of the liquid crystal order decreases with increasing 5CB content. Rheology is used to prove that the correlation length behaviour is related to a reduction in the viscosity of the mixture.

The 2:1 cycloadducts from [3+2] 1,3-dipolar cycloaddition of nitrile oxide and vinylacetic acid. Synthesis and liquid crystal behaviour

Four liquid crystals (LC) 3,7a-bis(4-alkyloxyphenyl)-7,7a-dihydro-6H-isoxazolo[2,3-d][1,2,4]oxadiazol-6-yl)acetic acid (7a-d) were synthesised and the mesomorphic behaviour reported. The LCs were characterised as 2: 1 bisadducts, which were obtained from a double [3+2] 1,3-dipolar cycloaddition. In the first step, the cycloaddition of 4-alkyloxyphenylnitrile oxide (4a-d) and vinylacetic acid (5) gave the initial unobserved 1:1 cycloadducts 2-[3-(4-alkyloxyphenyl)-4,5-dihydroisoxazol-5-yl]acetic acid (6a-d). In the second step, the addition of a second equivalent of 4 to 6 yielded the 2: 1 bisadducts 7a-d without any traces of 6. All compounds 7a-d were unstable during the transition from the mesophase to the isotropic state upon first heating as evidenced by the large peaks in the differential scanning calorimetry traces. Due to the chemical instability of the compounds upon heating, the transition temperature related to the smectic C to smectic A transitions was acquired by means of an image processing method. X-Ray diffraction experiments were also used to analyse the liquid-crystalline phases. A theoretical calculation was performed using density functional theory (DFT) methods at the PBE1PBE/6-311+G(2d,p) level (with solvent effect) in order to get information about the energetic profile of the 2: 1 cycloaddition. DFT studies revealed that the cycloaddition process is controlled by the HOMO(dipolarophile) - LUMO(1,3-dipole), and that the double [3+2] 1,3-dipolar cycloaddition reaction is quite possible.

Structural Analysis by X-Ray Diffraction of a Polar Mesogen 4-Cyanobiphenyl-4'-heptylbiphenyl Carboxylate

Crystal and molecular structure of a compound 4-cyanobiphenyl-4'-heptylbiphenyl carboxylate (7CBB), which exhibit both monolayer smectic A and nematic phases, have been determined by direct methods using single crystal X-ray diffraction data. The structure is monoclinic with the space group P21/c and Z = 4. The unit cell parameters are a = 16.9550(5) Aring, b = 5.5912(18) Aring, c = 27.5390(9) Aring, agr = 90.000°, β = 93.986(6)°, and γ = 90.000°. Packing of the molecules is found to be precursor to SmC phase, although SmA1 phase is observed on melting. Several strong van der Waals interactions are observed in the core part of the neighboring molecular pairs. Crystal to mesophase transition is probably of reconstitutive nature. Geometry, packing, and nature of crystal-mesophase transition are compared to those in 6CBB.

Colloidal dispersions in a liquid crystalline medium

We have prepared stable colloidal suspensions in a lyotropic liquid crystal exhibiting an isotropic-nematic-lamellar phase sequence. Small angle neutron scattering (SANS) and dynamic light scattering (DLS) studies show the existence of attractive interparticle interactions in the nematic phase, which lead to a gas-liquid transition of the particles. The resulting liquid phase is weakly anisotropic. Further, the nematic-lamellar transition of the liquid crystal is found to be accompanied by a liquid-solid transition of the particles.

Cross-polarisation applied to the study of liquid crsytalline ordering

Cross polarisation is extensively used in solid state NMR for enhancing signals of nuclei with low gyromagnetic ratio. However, the use of the method for providing quantitative structural and dynamics information is limited. This arises due to the fact that the mechanism which is responsible for cross polarisation namely, the dipolar interaction, has a long range and is also anisotropic. In nematic liquid crystals these limitations are easily overcome since molecules orient in a magnetic field. The uniaxial ordering of the molecules essentially removes problems associated with the angular dependence of the interactions encountered in powdered solids. The molecular motion averages out intermolecular dipolar interaction, while retaining partially averaged intramolecular interaction. In this article the use of cross polarisation for obtaining heteronuclear dipolar couplings and hence the order parameters of liquid crystals is presented. Several modifications to the basic experiment were considered and their utility illustrated. A method for obtaining proton-proton dipolar couplings, by utilizing cross polarisation from the dipolar reservoir, is also presented.

Study of liquid crystalline order by NMR

The liquid crystalline phase represents a unique state of matter where partial order exists on molecular and supra-molecular levels and is responsible for several interesting properties observed in this phase. Hence a detailed study of ordering in liquid crystals is of significant scientific and technological interest. NMR provides several parameters that can be used to obtain information about the liquid crystalline phase. Of these, the measurement of dipolar couplings between nuclei has proved to be a convenient way of obtaining liquid crystalline ordering since the coupling is dependent on the average orientation of the dipolar vector in the magnetic field which also aligns the liquid crystal.However, measurement of the dipolar coupling between a pair of selected nuclei is beset with problems that require special solutions. In this article the use of cross polarization for measuring dipolar couplings in liquid crystals is illustrated. Transient oscillations observed during cross polarization provide the dipolar couplings between essentially isolated nearest neighbor spins which can be extracted for several sites simultaneously by employing two-dimensional NMR techniques. The use of the method for obtaining heteronuclear dipolar couplings and hence the order parameters of liquid crystals is presented. Several modifications to the basic experiment are considered and their utility illustrated. A method for obtaining proton–proton dipolar couplings, by utilizing cross polarization from the dipolar reservoir, is presented. Some applications are also highlighted.

High-Resolution Solid State C-13 NMR Studies of Bent-Core Mesogens of Benzene and Thiophene

Bent-core mesogens are an important class of thermotropic liquid crystals as they exhibit unusual properties as well as morphologies distinctly different from rodlike mesogens. Two bent-core mesogens with differing center rings namely benzene and thiophene are considered and investigated using high-resolution oriented solid state C-13 NMR method in their liquid crystalline phases. The mesogens exhibit different phase sequences with the benzene-based mesogen showing a B-1 phase, while the one based on thiophene showing nematic and smectic C phases. The 2-dimensional separated local field (2D-SLF) NMR method was used to obtain the C-13-H-1 dipolar couplings of carbons in the center ring as well as in the side-wing phenyl rings. Couplings, characteristic of the type of the center ring, that also provide orientational information on the molecule in the magnetic field were observed. Together with the dipolar couplings of the side-wing phenyl ring carbons from which the local order parameters of the different subunits of the core could be extracted, the bent angle of the mesogenic molecule could be obtained. Accordingly, for the benzene mesogen in its B-1 phase at 145 degrees C, the center ring methine C-13-H-1 dipolar couplings were found to be significantly larger (9.5-10.2 kHz) compared to those of the side-wing rings (1.6-2.1 kHz). From the local order parameter values of the center (0.68) as well as the side-wing rings (0.50), a bent-angle of 130.3 degrees for this mesogen was obtained. Interestingly, for the thiophene mesogen in its smectic C phase at 210 degrees C, the C-13-H-1 dipolar coupling of the center ring methine carbon (2.11 kHz) is smaller than those of the side-wing phenyl ring carbons (2.75-3.00 kHz) which is a consequence of the different structures of the thiophene and the benzene rings. These values correspond to local order parameters of 0.85 for the center thiophene ring and 0.76 for the first side-wing phenyl ring and a bent-angle of 149.2 degrees. Thus, the significant differences in the dipolar couplings and the order parameter values between different parts in the rigid core of the mesogens are a direct consequence of the nature of the center ring and the bent structure of the molecule. The present investigation thus highlights the ability of the C-13 2D-SLF technique to provide the geometry of the bent-core mesogens in a straightforward manner through the measurement of the C-13-H-1 dipolar couplings.

Broad spectrum measurement of the birefringence of an isothiocyanate based liquid crystal.

Tunable materials with high anisotropy of refractive index and low loss are of particular interest in the microwave and terahertz range. Nematic liquid crystals are highly sensitive to electric and magnetic fields and may be designed to have particularly high birefringence. In this paper we investigate birefringence and absorption losses in an isothiocyanate based liquid crystal (designed for high anisotropy) in a broad range of the electromagnetic spectrum, namely 0.1-4 GHz, 30 GHz, 0.5-1.8 THz, and in the visible and near-infrared region (400 nm-1600 nm). We report high birefringence (Δn = 0.19-0.395) and low loss in this material. This is attractive for tunable microwave and terahertz device applications.

Liquid crystal based continuous phase retarder: From optically neutral to a quarter waveplate in 200 microseconds

Liquid crystal variable phase retarders have been incorporated into prototype devices for optical communications system applications, both as endless polarization controllers 1,2,3, and as holographic beam steerers 4. Nematic liquid crystals allow continuous control of the degree of retardation induced at relatively slow switching speeds, while ferroelectric liquid crystal based devices allow fast (sub millisecond) switching, but only between two bistable states. The flexoelectro-optic effect 5,6 in short-pitch chiral nematic liquid crystals allows both fast switching of the optic axis and continuous, electric field dependent control of the degree of rotation of the optic axis. A novel geometry for the flexoelectro-optic effect is presented here, in which the helical axis of the chiral nematic is perpendicular to the cell walls (grandjean texture) and the electric field is applied in the plane of the cell. This facilitates deflection of the optic axis of the uniaxial negatively birefringent material from lying along the direction of propagation to having some component in the polarization plane of the light. The device is therefore optically neutral at zero field for telecommunications wavelengths (1550nm), and allows a continuously variable degree of phase excursion to be induced, up to 2π/3 radians achieved so far in a 40μm thick cell. The retardation has been shown both to appear, on application of the field, and disappear on removal, at speeds of 100-500 μs. The direction of deflection of the optic axis is also dependent on the direction of the field, allowing the possibility, in a converging electrode "cartwheel cell", of endless rotation of the liquid crystal waveplate at a higher rate than achievable through dielectric coupling to plain nematic materials.

Studies on the phase diagram of the surfactant/1-pentanol water ternary system II: The liquid crystalline phase

The phase behavior of liquid crystalline in the ternary system of dodecyl dimethyl ammonium hydroxyl propyl sulfonate(DDAHPS)/1-pentanol(C5H11OH)/water deuteron (D2O) has been investigated by polarizing optical microscopy, H-2 NMR spectroscopy methods. The results indicate that two kinds of liquid crystals (the lamellar, and the hexagonal) exist in the liquid crystalline phase region. In this paper, we also use the polarized Raman spectroscopy method to measure the values of the order/disorder parameters and the values of the environment polarity parameters for the samples selected from the liquid crystalline phase region, and compare these two parameters of the samples with those of solid state DDAHPS and liquid state pentan-1-ol.

Assembly and inspection of liquid crystal on silicon devices

Liquid crystal on silicon (LCOS) is one of the most exciting technologies, combining the optical modulation characteristics of liquid crystals with the power and compactness of a silicon backplane. The objective of our work is to improve cell assembly and inspection methods by introducing new equipment for automated assembly and by using an optical inspection microscope. A Suss-Micro'Tec Universal device bonder is used for precision assembly and device packaging and an Olympus BX51 high resolution microscope is employed for device inspection. ©2009 Optical Society of America.

Pattern formation and spatial solitons in bistable liquid-crystal microcavities

We report on spatial pattern formation, and appearances of 'optical bullet holes' in single-mode microcavities that are filled with liquid-crystals, when pumped above the cavity resonance frequency. These phenomena only occur beyond the bistability threshold. ©2002 Optical Society of America.