Geoestatística e atributos do solo em áreas cultivadas com cana-de-açúcar

The intense traffic of agricultural machines in soils cultivated with sugar cane can cause soil compaction. Therefore, the objective of this research was to characterize the spatial variability of soil physical attributes and content organic matter of a eutroferric Red Latosol gibbisitic (under Basalt) and dystroferric Red Latosol caulinitic (under Sandstone) in the depths of 0.0-0.2m and 0.2-0.4m in areas cultivated with sugar cane. Soils were sampled at the crossing points of a grid at regular intervals of 10m and at depths of 0.0-0.2m and 0.2-0.4m. Bulk density, macroporosity, organic matter content and soil penetration resistance were measured for all sampling points. The physical attributes show values of soil penetration resistance, bulk density and macroporosity above average for these soils. The studied variable presented a larger range and minor variation coefficient in the eutroferric Red Latosol (Oxisol Eutrustox) when compared with the dystroferric Red Latosol (Oxisol Haplustox), in the studied depths. It is recommended a bigger number of samples to study the eutroferric Red Latosol attributes and the depth of 0.2-0.4m.

Mineralogy of the clay fraction of alfisols in two slope curvatures: IV - spatial correlation with physical properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relações solo-paisagem em uma litosseqüência arenito-basalto na região de Pereira Barreto, SP

Os objetivos deste trabalho foram estudar as relações solo-paisagem em uma litosseqüência de transição arenito-basalto e verificar a similaridade dos limites de superfícies geomórficas mapeados no campo com os limites mapeados a partir de técnicas geoestatísticas. Foi realizado o mapeamento de uma área de 530 ha, utilizando-se equipamento de GPS, e em seguida elaborou-se o Modelo de Elevação Digital, que possibilitou o estabelecimento da transeção de 2.100 m a partir do topo. Ao longo da transeção, o terreno foi estaqueado a intervalos regulares de 50 m, nos quais foram realizadas medidas da altitude para confecção do perfil altimétrico. As superfícies geomórficas foram identificadas e delimitadas conforme critérios topográficos e estratigráficos, com base em intensas investigações de campo. Coletaram-se amostras de solo em pontos laterais em 67 locais, nas superfícies geomórficas identificadas, nas profundidades de 0,0-0,25 m e 0,80-1,00 m. Além disso, foram abertas trincheiras nos segmentos de vertente inseridos nas superfícies geomórficas mapeadas. As amostras coletadas foram analisadas quanto a densidade do solo, textura, Ca2+, K+, Mg2+, SB, CTC, V, pH (água e KCl), SiO2, Al2O3 e Fe2O3 (ataque por H2SO4), óxidos de Fe livres extraído com ditionito-citrato-bicarbonato e ferro mal cristalizado extraídos com oxalato de amônio. A fração argila desferrificada foi analisada por difração de raios X. A compartimentação da paisagem em superfícies geomórficas e a identificação do material de origem mostraram-se bastante eficientes para entendimento da variação dos atributos do solo. A análise individual desses atributos por meio de estatística univariada auxiliou na discriminação das três superfícies geomórficas. O uso de técnicas de geoestatística permitiu a confirmação de que mesmo os atributos do solo apresentaram limites próximos aos das superfícies geomórficas.

Balanço hídrico e da salinidade do solo na bananeira irrigada com água de diferentes salinidades

O objetivo deste trabalho foi avaliar o efeito de diferentes níveis de salinidade de água de irrigação no uso consultivo na fase reprodutiva da bananeira e evolução da salinidade do solo. Adotou-se o delineamento inteiramente casualizado em parcelas subdivididas, totalizando oito tratamentos com quatro repetições por tratamento. Os níveis de salinidade foram obtidos a partir de águas naturais de poços dos aquíferos arenito e calcário e foram misturadas em tanques de alvenaria para a obtenção das concentrações de salinidade desejada. Verificou-se que a área do bulbo com umidade superior a 8% representa aproximadamente 50% do volume do solo. A evapotranspiração da cultura diminuiu com o aumento da salinidade entre os tratamentos, o kc médio no período variou de 1,01 a 1,09 em águas de salinidade extremas. Comparando os perfis da salinidade do solo, verificou-se que a concentração de sais foi superior na camada superficial aos 440 dias após plantio.

Superfícies geomórficas e atributos de Latossolos em uma seqüência Arenítico-Basáltica da região de Jaboticabal (SP)

Em um segmento de vertente com substrato de arenito em contato com basalto, regionalmente muito freqüente, pretendeu-se não só relacionar as superfícies geomórficas com os atributos físicos, químicos e mineralógicos dos Latossolos nelas encontrados, mas também testar métodos geoestatísticos para localização de limites dessas superfícies. Usando critérios geomorfológicos, três superfícies foram identificadas e topograficamente caracterizadas. Os solos foram amostrados, a intervalos regulares de 25 m, na profundidade de 0,6 a 0,8 m (topo do horizonte B), em uma transeção de 1.700 m perfazendo 109 pontos. Nas amostras, foram analisados: densidade de partículas, granulometria, CTC do solo, CTC da argila, Fe total da argila (ataque por H2SO4) e óxidos de Fe livres (por dissolução seletiva). A fração argila desferrificada foi analisada por difração de raios X. Com base na estratigrafia e variações do relevo local, foram identificadas e diferenciadas, no campo, três superfícies geomórficas. Analisaram-se também o perfil altimétrico e o modelo de elevação digital do terreno. Observou-se que as três diferentes superfícies estão bem relacionadas com os atributos físicos, químicos e mineralógicos dos seus respectivos solos. Na parte inferior desta vertente, superfície mais recente e sobre basalto, em Latossolo Vermelho eutroférrico típico, foram encontradas as maiores variabilidades da declividade, da argila e de Fe. As variações da inclinação do terreno, quando analisadas sistematicamente pelo split moving windows dissimilarity analysis (análise estatística de dissimilaridade, em segmentos móveis), mostraram que este método estatístico pode ser usado para ajudar a localizar os limites entre superfícies geomórficas. As variações dos solos da transeção, e arredores, mostraram-se relacionadas com idade, inclinação do terreno e litologia. O trabalho geomórfico detalhado forneceu importantes informações para subsidiar os trabalhos de levantamento de solos e de pedogênese.

Desenvolvimento de sistemas a base de tensoativos para recuperação avançada de petróleo

Petroleum is a complex combination of various classes of hydrocarbons, with paraffinic, naphtenic and aromatic compounds being those more commonly found in its composition. The recent changes in the world scenario, the large reserves of heavy oils and also the lack of new discoveries of large petroleum fields are indications that, in the near future, the oil recovery by conventional methods will be limited. In order to increase the efficiency of the extraction process, enhanced recovery methods are cited in applications where conventional techniques have proven to be little effective. The injection of surfactant solutions as an enhanced recovery method is advantageous in that surfactants are able to reduce the interfacial tensions between water and oil, thus augmenting the displacement efficiency and, as a consequence, increasing the recovery factor. This work aims to investigate the effects of some parameters that influence the surfactant behavior in solution, namely the type of surfactant, the critical micelle concentration (CMC) and the surface and interface tensions between fluids. Seawater solutions containing the surfactants PAN, PHN and PJN have been prepared for presenting lower interfacial tensions with petroleum and higher stability under increasing temperature and salinity. They were examined in an experimental apparatus designed to assess the recovery factor. Botucatu (Brazil) sandstone plug samples were submitted to assay steps comprising saturation with seawater and petroleum, conventional recovery with seawater and enhanced recovery with surfactant solutions. The plugs had porosity between 29.6 and 32.0%, with average effective permeability to water of 83 mD. The PJN surfactant, at a concentration 1000% above CMC in water, had a higher recovery factor, causing the original oil in place to be recovered by an extra 20.97%, after conventional recovery with seawater

Aplicação de microemulsões na solubilização de frações pesadas de petróleo

This work presents studies related to the use of microemulsions in the solubilization of heavy crude oil fractions responsible by the formation of deposits. The first stage of the work was addressed to the construction of phases diagrams, with the intention of determining the area within which the microemulsion is formed. The following systems were studied: UNITOL L 90 n-Butanol - Water - Kerosene (system 1); UNITOL L 90 - n-Butanol - Water - Xylene (system 2); UNITOL L 90 n-Butanol - Water - Kerosene/Xylene 10% (system 3); UNITOL L 90 - Sec-Butanol - Water - Xylene (system 4). In parallel experiments of physical adsorption were carried out by the static method, with the intention of simulating natural conditions of reservoirs. Crude oil of the Fazenda Belém field (Rio Grande do Norte), was used as solute, xylene as solvent and the Assu sandstone (Rio Grande do Norte, Brazil) and Botucatu sandstone (Paraná, Brazil) as rock reservoirs. The curves of adsorption presented the S format type, in agreement with the classification proposed by Giles, Smith and Huitson (1974). The solubilization process was accomplished in the batch method, by varying the time of agitation, the microemulsions and the solid/solution ratio. The experiments showed that the microemulsions presented high efficiency in the solubilization of the crude oil adsorbed on the sandstones. System 2 presented an efficiency of 99% for the Assu sandstone and 97% for the Botucatu sandstone

Aplicação de microemulsão na recuperação de petróleo de reservatórios carbonáticos

The large investment in exploration activities offshore Brazil has generated new findings, generally in carbonate reservoirs, with different wettability conditions usually considered in the sandstone, strongly water-wet. In general, the carbonates reservoirs tend to be oil-wet, it difficult to mobilize of oil these reservoirs. These oils can be mobilized by different methods, or it may reverse the wettability of the surface of the reservoir and facilitate the flow of oil, improving production rates. Thus, the objective of this work was to study the influence of inversion on the wettability of the rock in the production and recovery of petroleum from carbonate reservoirs, using microemulsions. Three systems were chosen with different classes of surfactants: a cationic (C16TAB), an anionic (SDS) and nonionic (Unitol L90). Studies of the influence of salinity on the formation of the microemulsion as well as the characterization of fluids using density and viscosity measurements were also performed. To verify the potential of microemulsion systems in changing the wettability state of the chalk oil-wet to water-wet, contact angle measurements were performed using chalk of neutral-wet as surface material. Overall, with respect to the ionic character of the surfactants tested, the cationic surfactant (C16TAB) had a greater potential for reversal in wettability able to transform the rock wettability neutral to strongly water-wet, when compared with the anionic surfactant (SDS) and nonionic (Unitol L90), which showed similar behavior, improving the wettability of the rock to water. The microemulsions of all surfactants studied were effective in oil recovery, resulting in 76.92% for the system with C16TAB, 67.42% for the SDS and 66.30% for Unitol L90 of residual oil

Desenvolvimento de sistemas de pastas leves para aplicação em cimentação de poços petrolíferos com baixo gradiente de fratura

All around the world, naturally occurring hydrocarbon deposits, consisting of oil and gas contained within rocks called reservoir rocks , generally sandstone or carbonate exists. These deposits are in varying conditions of pressure and depth from a few hundred to several thousand meters. In general, shallow reservoirs have greater tendency to fracture, since they have low fracture gradient, ie fractures are formed even with relatively low hydrostatic columns of fluid. These low fracture gradient areas are particularly common in onshore areas, like the Rio Grande do Norte basin. During a well drilling, one of the most favorable phases for the occurrence of fractures is during cementing, since the cement slurry used can have greater densities than the maximum allowed by the rock structure. Furthermore, in areas which are already naturally fractured, the use of regular cement slurries causes fluid loss into the formation, which may give rise to failures cementations and formation damages. Commercially, there are alternatives to the development of lightweight cement slurries, but these fail either because of their enormous cost, or because the cement properties were not good enough for most general applications, being restricted to each transaction for which the cement paste was made, or both reasons. In this work a statistical design was made to determine the influence of three variables, defined as the calcium chloride concentration, vermiculite concentration and nanosilica concentration in the various properties of the cement. The use of vermiculite, a low density ore present in large amounts in northeastern Brazil, as extensor for cementing slurries, enabled the production of stable cements, with high water/cement ratio, excellent rheological properties and low densities, which were set at 12.5 lb / gal, despite the fact that lower densities could be achieved. It is also seen that the calcium chloride is very useful as gelling and thickening agent, and their use in combination with nanosilica has a great effect on gel strength of the cement. Hydrothermal Stability studies showed that the pastes were stable in these conditions, and mechanical resistance tests showed values of the order of up to 10 MPa

Estudo de sistemas microemulsionados utilizando água do mar na recuperação avançada de petróleo

Petroleum exists in the nature in certain underground formations where it is adsorbed into the rocks pores. For the conventional recovery methods usually only 30% of the oil is extracted and this can be credited, basically, to three aspects: high viscosity of the oil, geology of the formation and high interfacial tensions between the reservoir s fluids. The enhanced recovery methods use the injection of a fluid or fluids mixture in a reservoir to act in points where the conventional process didn't reach the recovery rates. Microemulsion flooding, considered an enhanced method, has the purpose to desorb the oil from the rock formation and to attain an efficient displacement of the oil emulsion. With this in mind, this work was accomplished with two main objectives: the study of the parameters effect that influence a microemulsified system (surfactant and cosurfactant types, C/S rate and salinity) and the evaluation of displacement efficiency with the microemulsions that showed stability in the rich aqueous area. For the analyzed parameters it was chose the microemulsions composition used in the recovery stage: 25% water, 5% kerosene, 46.7% of butanol as cosurfactant and 23.3% of BC or SCO cosurfactant. The core plugs of Assu and Botucatu sandstones were appraised in porosity and permeability tests and then submitted to the steps of saturation with seawater and oil, conventional recovery with water and enhanced recovery with the selected microemulsions. The Botucatu sandstone presented better recovery parameters, and the microemulsion composed with BS surfactant had larger recovery efficiency (26.88%)

Avaliação do comportamento de fluidos micelares na recuperação avançada de petróleo

In heavy oil fields there is a great difficulty of the oil to flow from the reservoir to the well, making its production more difficult and with high cost. Most of the original volumes of oil found in the world are considered unrecoverable by the use of the current methods. The injection of micellar solutions has a direct action in the oil interfacial properties, resulting in an enhanced oil recovery. The objective of this research was the study and selection of micellar solutions with ability to decrease the interfacial interactions between fluids and reservoir formation, increasing oil production. The selected micellar solutions were obtained using commercial surfactants and surfactants synthesized in laboratory, based on the intrinsic properties of these molecules, to use in the enhanced oil recovery. Petroleum Reservoirs were simulated using sandstone plugs from Botucatu formation. Experiments with conventional and enhanced oil recovery techniques were accomplished. The obtained results showed that all micellar solutions were able to enhance oil recovery, and the micellar solution prepared with a SB anionic surfactant, at 2% KCl solution, showed the best recovery factor. It was also accomplished an economic analysis with the SB surfactant solution. With the injection of 20% porous volume of micellar solution, followed by brine injection, the increment in petroleum recovery can reach 81% recovery factor in the 3rd porous volume injected. The increment in the total cost by the addition of surfactant to the injection water represents R$ 7.50/ton of injected fluid

Desenvolvimento de tensoativos e sistemas microemulsionados para recuperação de petróleo

The high concentration of residual oil is one of the greatest problems found in petroleum mature fields. In these reservoirs, different enhanced oil recovery methods (EOR) can be used, highlighting the microemulsion injection. The microemulsion has showed to be efficient in petroleum recovery due to its ability to promote an efficient displacement of the petroleum, acting directly in the residual oil. In this way, this research has as objective the study of microemulsion systems obtained using a commercial surfactant (TP), determining microemulsion thermal stabilities and selecting points inside the pseudoternary phases diagram, evaluating its efficiencies and choosing the best system, that has the following composition: TP as surfactant (S), isopropyl alcohol as co-surfactant (C), kerosene as oil phase, water as aqueous phase, C/S ratio = 1, and 5% sodium p-toluenesulfonate as hydrotope; being observed the following parameters for the selection of the best pseudoternary phases diagram: C/S ratio, co-surfactant nature and addition of hydrotope to the system. The efficiency in petroleum recovery was obtained using two sandstone formation systems: Assu and Botucatu. The study of thermal stabilities showed that as the concentration of active matter in the system increased, the thermal stability also increased. The best thermal stability was obtained using point F (79.56 0C). The system that presented the best recovery percentile between the three selected (3) was composed by: 70% C/S, 2% kerosene and 28% water, with 94% of total recovery efficiency and 60% with microemulsion injection, using the Botucatu formation, that in a general way presented greater efficiencies as compared with the Assu one (81.3% of total recovery efficiency and 38.3% with microemulsion injection)

Influência da acrilamida e da poliacrilamida em sistema microemulsionado visando aplicação na recuperação avançada de petróleo

This work aims to study the influence of two additives, the monomer, acrylamide and its polymer, polyacrylamide, solubilized in microemulsion systems and applied on enhanced oil recovery. By the microemulsion system obtained, it was chosen points into the phase diagram, presenting these compositions: 25%, 30%, 35% C/T; 2% Fo (fixed for all points) e 73%, 68% e 63% Fa, respectively. However, the monomer and the polymer were solubilized in these microemulsion points with 0.1%; 0.5%; 1% e 2% of concentration, ordering to check the concentration influence at the physicochemical properties (surface tension and rheology) of the microemulsion. Through the salinity study, was possible to observe that the concentrations of 1% and 2% of polymer made the solution became blurred, accordingly, the study of surface tension and rheology only was made for the concentrations of 0.1% e 0.5% of monomer and polymer, respectively. By the surface tension study it was observed that how the concentration of active matter (C/T) was increasing the surface tension was amending for each system, with or without additives. In the rheology study, as it increases the concentration of active matter increases both the viscosity of the microemulsion system (SME) with no additive, as the SME with polymer (AD2). After the entire study, it was chosen the lower point of active matter (25% C/T; 2% Fo e 73% Fa), plus additives in concentrations of 0.1% and 0.5% to be used on enhanced oil recovery. Assays were made on sandstone from Botucatu Formation, where after the tests, it was concluded that among the studied points, the point who showed the best efficiency of advanced shift was the microemulsion system + 0.5% AD2, with a recovery of 28% of oil in place and a total of 96,49%, while the other solution with 0.5% of polymer presented the worst result, with 14.1% of oil in place and 67,39% of efficiency of total displacement

Entendendo as propriedades do arenito Botucatu e sua utilização como meio poroso para estudos envolvendo o deslocamento de fluidos poliméricos

The development of products whose purpose is to promote blockages in high permeability zones as well as to control the hydrate or scale formation also needs some tests in porous media before using the product in the field, where attempts and unavoidable operational errors costs would able to derail any projects. The aim of this study was to analyze and compare the Botucatu and Berea sandstones properties, involving problems related to loss permeability. It was observed that even cores of Berea, without expansible clays in their composition had their permeability reduced, as soon as the salinity of brine reached a lower limit. As expected, the same happened with the Botucatu sandstone samples, however, in this case, the sensitivity to low salinity was more pronounced. In a second phase, the research was focused on the Botucatu Sandstone behavior front of dilute polymer solutions injection, checking the main relationships between the Rock / Fluid interactions, considering the Mobility Reduction, Resistance and Residual Resistance Factors, as well as adsorption/desorption processes of these polymers, and the polymer molecules average size and porous sandstone average size ratio. The results for both phases showed a real feasibility of using the Botucatu sandstone in laboratory tests whose objective is the displacement of fluids through porous media

Viabilidade econômica do cultivo de abacaxi no arenito Caiuá, região noroeste do Estado do Paraná

A área da região noroeste do Estado do Paraná, sobre o arenito Caiuá, carece de opções de exploração agrícola economicamente viáveis. Assim, o abacaxi apresenta-se como opção de cultivo, entretanto, necessitando de maiores estudos referentes à sua exploração nesta região. O presente trabalho teve por objetivo avaliar a viabilidade socioeconômica do cultivo desta frutífera na região de Umuarama, Estado do Paraná em relação às principais regiões fornecedoras de abacaxi para o Estado. Para tanto, visitaram-se três propriedades nos municípios de Umuarama, Cafezal do Sul e Cruzeiro do Oeste, objetivando levantar os coeficientes técnicos desta atividade e seus indicadores de lucratividade. A região analisada apresenta boa capacidade competitiva em relação às regiões tradicionalmente produtoras (Frutal, Estado de Minas Gerais e Guaraçaí, Estado de São Paulo), principalmente pela proximidade do mercado consumidor. O abacaxi é uma excelente opção de cultivo no contexto da agricultura familiar.