Localização de faltas em linhas de transmissão usando morfologia matemática

This work an algorithm for fault location is proposed. It contains the following functions: fault detection, fault classification and fault location. Mathematical Morphology is used to process currents obtained in the monitored terminals. Unlike Fourier and Wavelet transforms that are usually applied to fault location, the Mathematical Morphology is a non-linear operation that uses only basic operation (sum, subtraction, maximum and minimum). Thus, Mathematical Morphology is computationally very efficient. For detection and classification functions, the Morphological Wavelet was used. On fault location module the Multiresolution Morphological Gradient was used to detect the traveling waves and their polarities. Hence, recorded the arrival in the two first traveling waves incident at the measured terminal and knowing the velocity of propagation, pinpoint the fault location can be estimated. The algorithm was applied in a 440 kV power transmission system, simulated on ATP. Several fault conditions where studied and the following parameters were evaluated: fault location, fault type, fault resistance, fault inception angle, noise level and sampling rate. The results show that the application of Mathematical Morphology in faults location is very promising

Estudoda sismicidade na região de Sobral - CE em 2008

The town of Sobral is located at the northwest part of the Ceará State, 250 km away from its capital, Fortaleza. In January 2008, an intense seismic activity began near Sobral with one event with magnitude 4,2mb on May 21. Since the start of its seismic activity, all events were recorded by the SBBR station (located on EMBRAPA Caprinos Farm), which operates in the region since August 2007. After this event, monitoring the seismic activity was carried out with the deployment of a local three component digital seismographic network, from June 5, 2008 until September 24. Initially, this network was composed of six seismographic stations. Later additional five stations were deployed until August 26 2008. This local network detected approximately 2,800 earthquakes. In this study we analyzed 581 earthquakes recorded by at least three stations for hypocentral and focal mechanism determination, and to contribute to a better explanation of the seismicity which in this region. To determine the hypocenters, we used a half-space model, with vP = 6,00 km/s and vP/vS = 1,71. From the hypocentral determination, it was revealed an active seismic zone with depth ranging between 1 and 8 km, 6 km long in E - W direction. The determination of fault planes and focal mechanism was obtained using the programs FPFIT and PLAN, which allowed comparison between their respective results in order to obtain more accurate results. A set of 24 earthquakes were selected to determine fault using PLAN planes and focal mechanisms using FPFIT. With the aid of detailed map of hypocenters this set, it was possible to identify three structures. Therefore, the set of 24 earthquakes were divided into three subsets. The type of mechanism was predominantly strike-slip with a dextral direction. Although the region has two tectonic structures near the site of the study area: the Café- Ipueiras Fault (normal fault) and the Sobral-Pedro II Lineament (dextral strike-slip fault) it was not possible to correlate the seismicity founded with those structures

Aplicação da modelagem estrutural computacional direta na análise da geometria de falhas: exemplo da falha de Baixa Grande (Bacia Potiguar - NE do Brasil)

The Baixa grande fault is located on the edge of the S-SW Potiguar Rift. It limits the south part of Umbuzeiro Graben and the Apodi Graben. Although a number of studies have associated the complex deformation styles in the hanging wall of the Baixa Grande Fault with geometry and displacement variations, none have applied the modern computational techniques such as geometrical and kinematic validations to address this problem. This work proposes a geometric analysis of the Baixa Fault using seismic interpretation. The interpretation was made on 3D seismic data of the Baixa Grande fault using the software OpendTect (dGB Earth Sciences). It was also used direct structural modeling, such as Analog Direct Modeling know as Folding Vectors and, 2D and 3D Direct Computational Modeling. The Folding Vectors Modeling presented great similarity with the conventional structural seismic interpretations of the Baixa Grande Fault, thus, the conventional interpretation was validated geometrically. The 2D direct computational modeling was made on some sections of the 3D data of the Baixa Grande Fault on software Move (Midland Valley Ltd) using the horizon modeling tool. The modeling confirms the influence of fault geometry on the hanging wall. The Baixa Grande Fault ramp-flat-ramp geometry generates synform on the concave segments of the fault and antiform in the convex segments. On the fault region that does not have segments angle change, the beds are dislocated without deformation, and on the listric faults occur rollover. On the direct 3D computational modeling, structural attributes were obtained as horizons on the hanging wall of the main fault, after the simulation of several levels of deformation along the fault. The occurrence of structures that indicates shortening in this modeling, also indicates that the antiforms on the Baixa Grande Fault were influenced by fault geometry

Modelagem estrutural física de semigrábens ortogonais e oblíquos à distenção regional: influência da trama do embasamento e comparação com analógicos no nordeste brasileiro

The physical structural modeling tool is being increasingly used in geology to provide information about the evolutionary stages (nucleation, growth) and geometry of geological structures at various scales. During the simulations of extensional tectonics, modeling provides a better understanding of fault geometry and evolution of the tectonic-stratigraphic architecture of rift basins. In this study a sandbox type apparatus was used to study the nucleation and development of basins influenced by previous structures within the basement, variably oriented as regards to the main extensional axis. Two types of experiments were conducted in order to: (i) simulate the individual (independent) development of half-grabens oriented orthogonal or oblique to the extension direction; (ii) simulate the simultaneous development of such half-grabens, orthogonal or oblique to the extension direction. In both cases the same materials (sand mixed with gypsum) were used and the same boundary conditions were maintained. The results were compared with a natural analogue represented by the Rio do Peixe Basin (one of the eocretaceous interior basins of Northeast Brazil). The obtained models allowed to observe the development of segmented border faults with listric geometry, often forming relay ramps, and the development of inner basins faults that affect only the basal strata, like the ones observed in the seismic sections of the natural analogue. The results confirm the importance of basement tectonic heritage in the geometry of rift depocenters

Analise de desempenho de observadores de estado robustos na localizacao de falhas

The state observers can reconstruct and monitor unmeasurable states. A new concept of fault detection and isolation using state observers is presented. The method selects the parameters from components that may fail during the process and constructs optimized robust observers. To isolate component failures via robust observation, a bank of detection observers is organized, in which each observer is only sensitive to one specified component failure while robust to all other component failures. This paper analyzes the performance of transient and steady-state behavior of the state observer.

Detecção e classificação de faltas de curto-circuito em sistemas de distribuição de energia elétrica usando lógica nebulosa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de modelos de falhas e observadores de estado em estruturas reticuladas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Diagnose de falhas via observadores de estado em sistemas mecânicos com absorvedores dinâmicos de vibrações tipo lâmina vibrante

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização estrutural de pós de 'SRTIO IND.3' puro e dopado com samário

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudos de estratégias de identificação paramétrica para detecção e diagnóstico de faltas em um processo industrial do tipo tanques comunicantes

Esta dissertação apresenta uma técnica para detecção e diagnósticos de faltas incipientes. Tais faltas provocam mudanças no comportamento do sistema sob investigação, o que se reflete em alterações nos valores dos parâmetros do seu modelo matemático representativo. Como plataforma de testes, foi elaborado um modelo de um sistema industrial em ambiente computacional Matlab/Simulink, o qual consiste em uma planta dinâmica composta de dois tanques comunicantes entre si. A modelagem dessa planta foi realizada através das equações físicas que descrevem a dinâmica do sistema. A falta, a que o sistema foi submetido, representa um estrangulamento gradual na tubulação de saída de um dos tanques. Esse estrangulamento provoca uma redução lenta, de até 20 %, na seção desse tubo. A técnica de detecção de falta foi realizada através da estimação em tempo real dos parâmetros de modelos Auto-regressivos com Entradas Exógenas (ARX) com estimadores Fuzzy e de Mínimos Quadrados Recursivos. Já, o diagnóstico do percentual de entupimento da tubulação foi obtido por um sistema fuzzy de rastreamento de parâmetro, realimentado pela integral do resíduo de detecção. Ao utilizar essa metodologia, foi possível detectar e diagnosticar a falta simulada em três pontos de operação diferentes do sistema. Em ambas as técnicas testadas, o método de MQR teve um bom desempenho, apenas para detectar a falta. Já, o método que utilizou estimação com supervisão fuzzy obteve melhor desempenho, em detectar e diagnosticar as faltas aplicadas ao sistema, constatando a proposta do trabalho.

Desenvolvimento de um sistema de instrumentação de medição de vibração mecânica em máquina rotativas, em tempo real, embarcado em FPGA

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Formação de professores: as diretrizes nacionais e o poder local

Coming as a result from a comprehensive research based on Lima’s studies (2008), this article is intended for investigating the process of reorganization of the Pedagogy course offered by a state public university since 2006, when the new National Curricular Guides were instituted. The subject matter brings up as one of its purposes to identify the main difficulties and the possible answers given in order to cause the changes to happen, taking in consideration both the external and internal interests of the institution. To further these aims, actual instruments were applied to the research: documents related to the Pedagogy course that were kept in the Council of the university and interviews with the members who took part in the process of readjustment. Because it is a public university, at first there was a mistaken presumption of the primacy of an administration founded upon democratic principles, in which the divergent opinions do not turn out to be taken as mere pretexts, but as an opportunity of dialogue and to establish collective projects. However, the results of the analysis shook that basic assumption and proved the opposite: the process was led to a rational/bureaucratic pattern of administration, the goals of which intended to adjust the institution to the external precepts and to establish the consensus — understood here as an absolute lack of conflicts. Nevertheless, it was chosen to conciliate the Pedagogy course to the national guides, without causing any harm to the departmental interests. These are reasons that justify satisfactorily the fact of this article being supposed to raise and quicken new and revitalized debate whenever there is an engagement of those who are most concerned for the duty of student teachers’ instruction, but mainly that of being expected to participate in the effective discussion/decision — making process of creating ends which to strive and work for.

Investigação sobre deformação neotectônica no lineamento Guapiara, região de Guapiara e Jacupiranga

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Tolerância a falha em um ambiente de computação em nuvem open source

Pós-graduação em Ciência da Computação - IBILCE

Investigação de técnicas para o acompanhamento do desgaste de um par engrenado utilizando tribologia e análise da resposta dinâmica processada via função densidade probabilidade Beta

Pós-graduação em Engenharia Mecânica - FEIS