Effect of blade tip geometry on the tip leakage flow in axial turbine cascades

The phenomenon of tip leakage has been studied in two linear cascades of turbine blades. The investigation includes an examination of the performance of the cascades with a variety of tip geometries. The effects of using plain tips, suction side squealers, and pressure side squealers are reported. Traverses of the exit flow field were made in order to determine the overall performance. A method of calculating the tip discharge coefficients for squealer geometries is put forward. In linking the tip discharge coefficient and cascade losses, a procedure for predicting the relative performance of tip geometries is developed. The model is used to examine the results obtained using the different tip treatments and to highlight the important aspects of the loss generation process.

Investigation of the effect of combustor cooling geometry on acoustic energy absorption

To control combustion instabilities occurring in LPP gas turbine combustors, several active and passive systems have been developed in recent years. The combustion chamber cooling geometry has the potential to influence instability feedback loops by absorbing acoustical energy inside the combustor. The design of the cooling liner and the geometry of the cooling plenum and the cooling air flow rate have a significant influence on the absorption characteristics of the system. This paper presents the results of a cold flow study which was carried out in the course of a comprehensive study on the influence of the cooling geometry on combustor thermoacoustics. Absorption characteristics of three different cooling liner geometries and non-perforated plates were determined over a frequency range from 50 Hz to 600 Hz for different cooling flow rates and different cooling plenum volumes. The experimental results compared well with results from a low order thermoacoustic network model. The acoustic energy absorption spectrum of a cooling liner with 90°-hole configuration was found to be strongly dependent on cooling flow rate and cooling plenum volume, whereas the absorption spectrum of cooling liners with 25°-holes were found to be strongly dependent on the cooling plenum volume, but less dependent on the cooling air flow rate. All cooling liner setups with perforations were capable of increased acoustic absorption over a broad band of frequencies compared to the case of non-perforated combustor walls. © 2010 by Johannes Schmidt.

Using Level Sets as the basis for a scalable, parallel geometry engine and mesh generation system

The background to this review paper is research we have performed over recent years aimed at developing a simulation system capable of handling large scale, real world applications implemented in an end-to-end parallel, scalable manner. The particular focus of this paper is the use of a Level Set solid modeling geometry kernel within this parallel framework to enable automated design optimization without topological restrictions and on geometries of arbitrary complexity. Also described is another interesting application of Level Sets: their use in guiding the export of a body-conformal mesh from our basic cut-Cartesian background octree - mesh - this permits third party flow solvers to be deployed. As a practical demonstrations meshes of guaranteed quality are generated and flow-solved for a B747 in full landing configuration and an automated optimization is performed on a cooled turbine tip geometry. Copyright © 2009 by W.N.Dawes.

Shelf life of dried products from small indigenous fish species under various packing and storage conditions

The overall quality of five SIS products was found in good condition up to 2 months storage on the basis of organoleptic, biochemical and bacteriological characteristics and all the products was excellent in sealed packed condition up to 45 days of storage. However, quality of the products stored in open air atmospheric temperature was found excellent for first 15 days. In an average the initial moisture content was in the range of 13.5 to 15.0% with highest moisture content in puti and lowest in chapila. At the end of the 60 days the moisture content reached to the range of 18.5 to 19.0% which was more or less near the recommended limit of 16% for dried fishery products. The moisture content beyond the recommended limit as the storage period increased further and at the end of 90 days the moisture content increased to the range of 22.9 to 24% when organoleptically the product quality became very poor. The changes in the value of total volatile base nitrogen (TVB-N), peroxide value (PO), moisture and aerobic plate count (APC) of solar tunnel dried products in sealed polythene packages were investigated during 60 days of storage. There was little or no differences in TVB-N, PO and bacterial load of each species packed under various polythene density. The initial TVB-N values were in the range of 10.30 to 12.40 mg/100g of the samples. TVB-N value increased slowly up to the end of the storage period and was to in the range of 46.20 to 57.00 mg/1 00 g of sample. Initially the peroxide values (P.O.) were in the range of 6.54 to 8.40 m.eq./kg oil of the samples. During 60 days of storage, P.O. values increased slowly and at the end of the storage period these values reached to the range of 22.00 to 25.30meq./kg of sample. The initial APC was in the range 5.3xl04-7.3x104 CFU/g. The bacterial load increased slowly and at the end of the 60 days storage period reached to the range 6.6x106 - 8.6x107 CFT/g.