Caracterização hidráulica do aspersor Super 10 e sua influência na energia cinética e erosividade

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Diretrizes básicas para projetos de vasos de pressão segundo a ASME Trabalho

In this work it was made analysis of a simple pressure vessel, using the analytical development studied in Mechanics of Materials disciplines, and then using the standard required by ASME. Following the simulation was realized using Autodesk Mechanical Simulation software to calculate the principal stresses in a pressure vessel. The simulation was done in a single vessel without nozzles, compared with the analytic calculation. After that, the simulation of another fictitious pressure vessel was done by adding three nozzles to verify the influence of the nozzles in the principal stresses and compared with the analytical results. After the simulation, it was found that the principal are bigger in the pressure vessel with nozzles, but they decrease at a small distance from the nozzle becoming equal to the stresses in the vessel without nozzles. The analytical results calculated according to the ASME agree with simulated results

Spray adjuvant characteristics affecting agricultural spraying drift

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Interação pontas-adjuvantes na estimativa do risco potencial de deriva de pulverizações

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Tar reduction in downdraft biomass gasifier using a primary method

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de pontas de jato plano na deposição da calda de pulverização com diferentes combinações de plantas de feijão, Brachiaria plantaginea e Bidens pilosa

Objetivou-se com este trabalho avaliar a ponta XR na deposição da calda de pulverização com diferentes combinações de plantas de feijão, Brachiaria plantaginea e Bidens pilosa, em dois volumes de aplicação, com e sem a adição de surfatante Silwet. Foi utilizado como traçador o corante Azul Brilhante FDC -1 na concentração de 500 ppm para quantificar a deposição. Os tratamentos constituíram-se de sete combinações de plantas: (feijão), (B. plantaginea), (B. pilosa), (feijão + B. plantaginea), (feijão + B. pilosa), (B. plantaginea + B. pilosa) e (feijão + B. plantaginea + B. pilosa). O delineamento experimental foi o inteiramente casualizado. Foram avaliadas as pontas de jato plano XR 110015 VS e XR 11002 VS com volumes de aplicação de 150 e 200 L ha-1, respectivamente, com e sem a presença do Silwet a 0,05% v v-1. Após a aplicação, as plantas foram imediatamente coletadas e, em seguida, lavadas em 100 mL de água destilada, para posterior quantificação do traçador em espectrofotômetro. As pontas XR apresentaram comportamento distinto na deposição das gotas de pulverização nas espécies estudadas; a adição de um surfatante à calda de pulverização aumentou a uniformidade da deposição nos alvos e contribuiu para a redução do volume de aplicação.

Métodos de coleta de deposição para ensaios de deriva em aplicações aéreas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Glifosato e manganês na cultura da soja transgênica: fisiologia e nutrição de planta, características agronômicas e análise econômica

Pós-graduação em Agronomia - FEIS

Espectro de gotas e potencial de deriva de caldas contendo o herbicida 2,4-d amina em misturas em tanque

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Avaliação de um pulverizador e volume ultra baixo e de adjuvantes em caldas fitossanitárias na cultura dos citros

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Influência de pressões de trabalho, espaçamentos e altura de instalação na distribuição de água de aspersor autocompensante

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Desempenho de pontas de pulverização quanto a indução de ar nas gotas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Espectro de gotas gerado por diferentes adjuvantes e pontas de pulverização

The application technology shows many parameters related to the quality of the application, one is the droplet spectrum, which is influenced by the spray nozzles and the adjuvant used. Therefore, the objective of this work was estimate the behavior of the droplet spectrum generated with different nozzles and different adjuvants. The experiment was installed containing four solutions from different type adjuvant dilution, as vegetal oil, mineral oil, surfactant and drift reduction, which were applied with two nozzle, one pre-orifice flat fan (DG 8003 VS) and other of air induction flat fan (AI 8003 VS), totaling 8 treatments with 3 repetitions. The experiment was realized in ideal weather conditions for spraying. The treatments averages were compared using Confidence Interval at 95% probability and the correlations between variables were analyzed using Pearson at 5% of probability. The analysis of droplet spectrum showed different behavior for each adjuvant and nozzle. The surfactant treatment showed VMD superior for all treatments when sprayed with AI nozzles. For the %vol.<100 µm the lowest value found was for the AI nozzle in combination with the surfactant. The significant correlations found for the nozzles AI and DG were negative between VMD and %vol.<100 µm. It can be concluded that the values of DMV and %vol.<100 µm showed that the nozzle with pre-orifice have droplet spectrum more prone to drift. The surfactant showed to be the best drift reduction technique when combined with the AI nozzle.

Adjuvantes na deposição de aplicações aéreas e terrestres

The Asian rust currently is the main disease of soybean culture, having as characteristics the difficult control, by start at the bottom of plants where penetration of the droplets is harder. The fine droplets has been used with the intention of improve the penetration and increase efficiency of agrochemicals, but that are losses by drift easily. New products have been developed to increase deposition of the drops at targets. The aim of this work was evaluate the TA- 35 capacity to improving the deposition of fungicides spray solution with or without mineral oil by aerial and ground applications. Was used a factorial 3x2, three spray solutions composed by Priori Xtra (concentrated suspension of azoxystrobin 200 g L-1 + cyproconazole 80 g L-1 ) mixed with adjuvants, Nimbus (emulsifiable concentrate containing aliphatic hydrocarbons 428 g L-1 ) and TA-35 (soluble concentrate containing sodium lauryl ether sulfate, surfactants, sequestering agents and emulsifiers), in aerial and ground applications. In ground applications was used 50 L ha-1 , TXA 8002 VS spray nozzles and on aerials was used 15 L ha-1 , Turboaero atomizer, both applying fine droplets. Was utilized the Brilliant Blue (FD & C n. 1) tracer to determine the deposits. There were used glass slides as targets to collect spray droplets. After to extract the tracer of the targets using distilled water, the samples were analyzed by spectrophotometry, thereby was possible quantify the tracer deposited on each glass slide. A study to evaluate possible losses of the tracer by degradation or retention also was done. The comparative analysis of treatments was done by statistical method "Confidence Interval for Differences Between the Averages" with 95% of confidence degree (IC95%). There was degradation or retention of the tracer between the processes of application of the droplets and the processing of the samples. The deposition averages with the presence of TA-35 were greatest for both sprayers however, there were not significant differences among the treatments. The viability of TA-35 use may consider other parameters or complementary studies.

Tecnologias de aplicação de produtos fitossanitários no controle de percevejos pragas na cultura da soja

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)