Optimal input cross-power spectra in shake table testing of asymmetric structures

The study considers earthquake shake table testing of bending-torsion coupled structures under multi-component stationary random earthquake excitations. An experimental procedure to arrive at the optimal excitation cross-power spectral density (psd) functions which maximize/minimize the steady state variance of a chosen response variable is proposed. These optimal functions are shown to be derivable in terms of a set of system frequency response functions which could be measured experimentally without necessitating an idealized mathematical model to be postulated for the structure under study. The relationship between these optimized cross-psd functions to the most favourable/least favourable angle of incidence of seismic waves on the structure is noted. The optimal functions are also shown to be system dependent, mathematically the sharpest, and correspond to neither fully correlated motions nor independent motions. The proposed experimental procedure is demonstrated through shake table studies on two laboratory scale building frame models.

Dynamic Characteristics of Spherically Converging Detonation Waves

The spherically converging detonation wave was numerically investigated by solving the one-dimensional multi-component Euler equations in spherical coordinates with a dispersion-controlled dissipative scheme. Finite rate and detailed chemical reaction models were used and numerical solutions were obtained for both a spherical by converging detonation in a stoichiometric hydrogen-oxygen mixture and a spherically focusing shock in air. The results showed that the post-shock pressure approximately arises to the same amplitude in vicinity of the focal point for the two cases, but the post-shock temperature level mainly depends on chemical reactions and molecular dissociations of a gas mixture. While the chemical reaction heat plays an important role in the early stage of detonation wave propagation, gas dissociations dramatically affect the post-shock flow states near the focal point. The maximum pressure and temperature, non-dimensionalized by their initial value, are approximately scaled to the propagation radius over the initial detonation diameter. The post-shock pressure is proportional to the initial pressure of the detonable mixture, and the post-shock temperature is also increased with the initial pressure, but in a much lower rate than that of the post-shock pressure.

Effects of adiabatic exponent on Richtmyer-Meshkov instability

We present a systematical numerical study of the effects of adiabatic exponent gamma on Richtmyer-Meshkov instability (RMI) driven by cylindrical shock waves, based on the gamma model for the multi-component problems and numerical simulation with high-order and high-resolution method for compressible Euler equations. The results show that the RMI of different gamma across the interface exhibits different evolution features with the case of single gamma. Moreover, the large gamma can hold back the development of nonlinear structures, such as spikes and bubbles.

Agent based modeling of energy networks

Attempts to model any present or future power grid face a huge challenge because a power grid is a complex system, with feedback and multi-agent behaviors, integrated by generation, distribution, storage and consumption systems, using various control and automation computing systems to manage electricity flows. Our approach to modeling is to build upon an established model of the low voltage electricity network which is tested and proven, by extending it to a generalized energy model. But, in order to address the crucial issues of energy efficiency, additional processes like energy conversion and storage, and further energy carriers, such as gas, heat, etc., besides the traditional electrical one, must be considered. Therefore a more powerful model, provided with enhanced nodes or conversion points, able to deal with multidimensional flows, is being required. This article addresses the issue of modeling a local multi-carrier energy network. This problem can be considered as an extension of modeling a low voltage distribution network located at some urban or rural geographic area. But instead of using an external power flow analysis package to do the power flow calculations, as used in electric networks, in this work we integrate a multiagent algorithm to perform the task, in a concurrent way to the other simulation tasks, and not only for the electric fluid but also for a number of additional energy carriers. As the model is mainly focused in system operation, generation and load models are not developed.

Pathway to poverty alleviation at the fishing communities of Lake Chad basin

Poverty has been variously measured in terms of income, consumption, and access to social and physical infrastructures. It is a multi-component phenomenon that cannot be measured by one single variable. This indicates that poverty alleviation or eradication requires a holistic approach. Because the existing strategies at ensuring poverty alleviation have not made impact at the Lake Chad Basin. Therefore, this study identifies the strategies that are adaptable to the area. Data were obtained on Literacy, income, quality housing, mobility, and access to infrastructure, cultural and socio-economic. The paper develops a pragmatic strategy through which the fishing communities can experience true empowerment and improved standard of living

Yb^3＋掺杂锌锗碲酸盐玻璃的热分析、光谱和激光性质

设计了组成为0．70TeO2-(0．20-x)ZnO-xGeO2—0．05La2O3-0．025K2O-0．025Na2O-0．01Yb2O3(摩尔分数x=0,0．05，0．10，0．15和0．20)的碲酸盐激光玻璃，测试了热学性质、吸收光谱、荧光光谱和荧光寿命。计算了Yb^3+离子的吸收截面、受激发射截面、荧光有效线宽等参数。结果表明，组成为0．70TeO2-0．20GeO2-0．05La2O3-0．025K2O-0．025Na2O的玻璃具有优于著名的碲锌钠(TZN)玻璃的热稳定性，高的受激发射截面(1

稀土离子掺杂的多组分玻璃光纤

abstract {Rare earth ions doped multi-component glass fibers have important application in broad band fiber amplifier and up-conversion fiber lasers. In this paper, the mechanism and the progress of study on rare earth ions doped multi-component glass fibers in broad band fiber amplifier and up-conversion fiber lasers are introduced and reviewed. The questions and the applications of rare earth ions doped multi-component glass fibers in the future are also prospected. Based on the present research progress, it is suggested to further study the tellurite and bismuth glasses, which are used as fiber materials in broad band fiber amplifier. To up-conversion fiber laser, it is still need to further investigate novel glasses, which has low phonon energy and good physical and chemical properties.}

Diffusion and chemical reaction in the porous structures of solid oxide fuel cells

The Rolls-Royce Integrated-Planar Solid Oxide Fuel Cell (IP-SOFC) consists of ceramic modules which have electrochemical cells printed on the outer surfaces. The cathodes are the outermost layer of each cell and are supplied with oxygen from air flowing over the outside of the module. The anodes are in direct contact with the ceramic structure and are supplied with fuel from internal gas channels. Natural gas is reformed into hydrogen for use by the fuel cells in a separate reformer module of similar design except that the fuel cells are replaced by a reforming catalyst layer. The performance of the modules is intrinsically linked to the behaviour of the gas flows within their porous structures. Because the porous layers are very thin, a one-dimensional flow model provides a good representation of the flow property variations between fuel channel and fuel cell or reforming catalyst. The multi-component convective-diffusive flows are simulated using a new theory of flow in porous material, the Cylindrical Pore Interpolation Model. The effects of the catalysed methane reforming and water-gas shift chemical reactions are also considered using appropriate kinetic models. It is found that the shift reaction, which is catalysed by the anode material, has certain beneficial effects on the fuel cell module performance. In the reformer module it was found that the flow resistance of the porous support structure makes it difficult to sustain a high methane conversion rate. Although the analysis is based on IP-SOFC geometry, the modelling approach and general conclusions are applicable to other types of SOFC.

Effects of preferential transport in turbulent bluff-body-stabilized lean premixed CH 4/air flames

Preferential species diffusion is known to have important effects on local flame structure in turbulent premixed flames, and differential diffusion of heat and mass can have significant effects on both local flame structure and global flame parameters, such as turbulent flame speed. However, models for turbulent premixed combustion normally assume that atomic mass fractions are conserved from reactants to fully burnt products. Experiments reported here indicate that this basic assumption may be incorrect for an important class of turbulent flames. Measurements of major species and temperature in the near field of turbulent, bluff-body stabilized, lean premixed methane-air flames (Le=0.98) reveal significant departures from expected conditional mean compositional structure in the combustion products as well as within the flame. Net increases exceeding 10% in the equivalence ratio and the carbon-to-hydrogen atom ratio are observed across the turbulent flame brush. Corresponding measurements across an unstrained laminar flame at similar equivalence ratio are in close agreement with calculations performed using Chemkin with the GRI 3.0 mechanism and multi-component transport, confirming accuracy of experimental techniques. Results suggest that the large effects observed in the turbulent bluff-body burner are cause by preferential transport of H 2 and H 2O through the preheat zone ahead of CO 2 and CO, followed by convective transport downstream and away from the local flame brush. This preferential transport effect increases with increasing velocity of reactants past the bluff body and is apparently amplified by the presence of a strong recirculation zone where excess CO 2 is accumulated. © 2011 The Combustion Institute.

A 5-step reduced mechanism for combustion of CO/H2/H2O/CH4/CO2 mixtures with low hydrogen/methane and high H2O content

In this study a 5-step reduced chemical kinetic mechanism involving nine species is developed for combustion of Blast Furnace Gas (BFG), a multi-component fuel containing CO/H2/CH4/CO2, typically with low hydrogen, methane and high water fractions, for conditions relevant for stationary gas-turbine combustion. This reduced mechanism is obtained from a 49-reaction skeletal mechanism which is a modified subset of GRI Mech 3.0. The skeletal and reduced mechanisms are validated for laminar flame speeds, ignition delay times and flame structure with available experimental data, and using computational results with a comprehensive set of elementary reactions. Overall, both the skeletal and reduced mechanisms show a very good agreement over a wide range of pressure, reactant temperature and fuel mixture composition. © 2012 The Combustion Institute..

Electronic load interface for improving PV dual-converter system operational margin

An electronic load interface (ELI) for improving the operational margin of a photovoltaic (PV) dual-converter system under dynamic conditions is presented. The ELI - based on a modified buck-boost converter - interfaces the output of the converters and the load system. It improves the operational margin of the PV dual-converter system by extending the conditions under which the dual-converter system operates at the maximum power point. The ELI is activated as and when needed, so as minimise system losses. By employing the ELI, utilisation and efficiency of a PV dual-converter system increases. In general, the concept of the ELI can be applied to multi-converter PV systems - such as multi-converter inverters, and multi-converter DC-DC converter systems - for performance and efficiency improvement. © 2013 The Institution of Engineering and Technology.

One-dimensional incoherently coupled grey solitons in two-photon photorefractive media

We show that grey solitons, grey-grey soliton pairs, and multi-component grey solitons can be realized in two-photon photorefractive media. The results for soliton pairs and multi-component solitons are derived under the assumption that the carrier beams share the same polarization, wavelength, and are mutually incoherent.

真菌单宁酶发酵五倍子和有机溶剂中酶法合成没食子酸丙酯的研究

本文报告了丝状真菌单宁酶发酵五倍子及有机溶剂中酶法合成没食子酸丙酯的研究。利用单宁和/或五倍子诱导丝状真菌产生单宁 酶的原理，借助二级发酵程序，对从天然源得到的75株菌进行了生物转化实验研究。选择出既能水解单宁或五倍子成没食子酸，又 能把没食子酸和丙醇合成没食子酸丙酯，而且生物催化活性都较高的1株菌，这株菌经初步鉴定为黑曲霉(Aspergillus niger No.17)。随后对它开展了产酶条件和参数优化实验，得出了最佳培养条件。立足于参数优化实验方案的基础上，经由液体培养发酵 制备单宁酶制剂，并把该酶通过化学手段共价结合到一种新型载体—聚乙烯醇和戊二醛反应生成的缩醛上，制备得到固定化单宁酶 。这种固定化生物催化剂在两种有机介质体系中都具有逆向催化合成没食子酸丙酯的能力。最后建立起来一条有效可行的微生物酶 法制备没食子酸的技术途径，没食子酸产率达到70%。对这种物质进行元素 分析：含C,49.45%;含H,3.63%。它的熔点为237℃～243 ℃，三种溶剂系统的TLC均只给出一个斑点。这些数据都与标准品一致。有机溶剂中酶法合成没食子酸丙酯的技术途径已经建立。 水溶性单宁酶在潜溶剂体系中也能催化上述酯化反应，反应混合物中的PG浓度为16.4mmol/L，制备薄层被用于分离反应混合物所含 的PG，这种产物被红外、质谱及三种溶剂系统的TLC等方法鉴定，确证为目标产物。在这一学位论文的实验研究过程中，还包括一 些生化分析方法的建立和应用，这些方法用于鉴定底物和产物及测定它们的浓度，其内容主要包括TLC定性/半定量分析、元素分析 、质谱、红外等手段的综合运用。本工作为开发我国特有的天然产物资源—五倍子的生物化工加工技术及非水相生物催化技术的开 发，提供了有用的基础数据资料，具有应用基础研究工作的重要性。In this thesis, the studies on the fermentation of Chinese gallotannin by filamentous fungi with tannase activity and enzymatic synthesis of propyl gallate(PG) in organic solvents were described through these biocatalysts. Based on the principles of induction enzyme, the tannase produced from filamentous fungi by adding tannic acid(TA) and/or Chinese gallotannin into media was investigated, and the screening experiments of bioconversion were done with 75 strains by means of a two-stage fermentation procedure. These strains were isolated with the enrichment culture technique from natural sources. Hence we selected one strain (Aspergillus niger No.17) that can not only catalyze the hydrolyses of TA and/or Chinese gallotannin into gallic acid(GA) in the liquid cultures, but also be used to synthesize PG from propanol and GA in the non-aqueous media. At the same time both of its biocatalytical activities were higher. This strain was calssified to be Aspergillus niger by the primary identification. Then optimum conditions for production of the tannase and its parameters were examined. In this way, one set of optimum culture conditions was selected. Making use of the optimum proposal, the tanase was prepared through a liquid fermentation procedure. The enzyme was convalently coupled to a new type of carrier which was made chemically from polyvinyl alcohol(PVA)and glutaraldehyde. The immobilized enzymes were able to synthesize PG reversely in two organic media. Finally, an effective enzymatic technique for production of GA was developed. The yield of GA products was up to 70%。Element analysis for this substance: calce: C, 49.42%; H, 3.56%; found: C, 49.45%, H, 3.63%. Its melting point was 237℃～ 243℃ and TLCs on three solvent systems gave only one spot respectively. These data were identical with theauthentic GA. The enzymatic synthesis of PG in organic solvents was extablished with reverse route of tannase catalytical hydrolysis. Aqueous enzyme perparation also catalyzed above esterification in a buffer system. The PG concentration in the reaction mixture was 16.4mmol/L. The reparative-scale TLC was used to isolate PG from the reaction mixture. This product separated was identified by IR, MS and TLC on three solvent systems. In this study of thesis, some biochemical analytical mehtods were developed and used to identify substrates and products, and to determinate their concentration. These methods, including TLC qualitative/half quantitative analysis, element analysis, MS, IR and so on, were useful, available and performable. This work provided basic data and information for developing the biochemical engineering and bio-processing of Chinese gallotannin-a special natural resource in China and the non-aqueous phase biocatalysis. Thus, this study possesses importance in the applied and basic research work.

Topological objects in two-gap superconductor

We discuss the non-Abelian topological objects, in particular the non-Abrikosov vortex and the magnetic knot made of the twisted non-Abrikosov vortex, in two-gap superconductor. We show that there are two types of non-Abrikosov vortex in Ginzburg-Landau theory of two-gap superconductor, the D-type which has no concentration of the condensate at the core and the N-type which has a non-trivial profile of the condensate at the core, under a wide class of realistic interaction potential. We prove that these non-Abrikosov vortices can have either integral or fractional magnetic flux, depending on the interaction potential. We show that they are described by the non-Abelian topology pi(2)(S-2) and pi(1)(S-1), in addition to the well-known Abelian topology pi(1)(S-1). Furthermore, we discuss the possibility to construct a stable magnetic knot in two-gap superconductor by twisting the non-Abrikosov vortex and connecting two periodic ends together, whose knot topology pi(3)(S-2) is described by the Chern-Simon index of the electromagnetic potential. We argue that similar topological objects may exist in multi-gap or multi-layer superconductors and multi-component Bose-Einstein condensates and superfluids, and discuss how these topological objects can be constructed in MgB2, Sr2RuO4, He-3, and liquid metallic hydrogen.

A Semi-Quantitative Analysis of Essential Micronutrient in Folium Lycii Using Laser-Induced Breakdown Spectroscopy Technique

In this paper, the capabilities of laser-induced break down spectroscopy (LIBS) for rapid analysis to multi-component plant are illustrated using a 1064 nm laser focused onto the surface of folium lycii. Based on homogeneous plasma assumption, nine of essential micronutrients in folium lycii are identified. Using Saha equation and Boltzmann plot method electron density and plasma temperature are obtained, and the irrelative concentration (Ca, Mg, Al, Si, Ti, Na, K, Li, and Sr) are obtained employing a semi-quantitative method.