Capacity-approaching rate function for layered multiantenna architectures

The simultaneous use of multiple transmit and receive antennas can unleash very large capacity increases in rich multipath environments. Although such capacities can be approached by layered multi-antenna architectures with per-antenna rate control, the need for short-term feedback arises as a potential impediment, in particular as the number of antennas—and thus the number of rates to be controlled—increases. What we show, however, is that the need for short-term feedback in fact vanishes as the number of antennas and/or the diversity order increases. Specifically, the rate supported by each transmit antenna becomes deterministic and a sole function of the signal-to-noise, the ratio of transmit and receive antennas, and the decoding order, all of which are either fixed or slowly varying. More generally, we illustrate -through this specific derivation— the relevance of some established random CDMA results to the single-user multi-antenna problem.

Sequential estimation of multipath MIMO-OFDM channels

Wireless “MIMO” systems, employing multiple transmit and receive antennas, promise a significant increase of channel capacity, while orthogonal frequency-division multiplexing (OFDM) is attracting a good deal of attention due to its robustness to multipath fading. Thus, the combination of both techniques is an attractive proposition for radio transmission. The goal of this paper is the description and analysis of a new and novel pilot-aided estimator of multipath block-fading channels. Typical models leading to estimation algorithms assume the number of multipath components and delays to be constant (and often known), while their amplitudes are allowed to vary with time. Our estimator is focused instead on the more realistic assumption that the number of channel taps is also unknown and varies with time following a known probabilistic model. The estimation problem arising from these assumptions is solved using Random-Set Theory (RST), whereby one regards the multipath-channel response as a single set-valued random entity.Within this framework, Bayesian recursive equations determine the evolution with time of the channel estimator. Due to the lack of a closed form for the solution of Bayesian equations, a (Rao–Blackwellized) particle filter (RBPF) implementation ofthe channel estimator is advocated. Since the resulting estimator exhibits a complexity which grows exponentially with the number of multipath components, a simplified version is also introduced. Simulation results describing the performance of our channel estimator demonstrate its effectiveness.

Mutual information of IID complex Gaussian signals on block Rayleigh-faded channels

We present a method to compute, quickly and efficiently, the mutual information achieved by an IID (independent identically distributed) complex Gaussian signal on a block Rayleigh-faded channel without side information at the receiver. The method accommodates both scalar and MIMO (multiple-input multiple-output) settings. Operationally, this mutual information represents the highest spectral efficiency that can be attained using Gaussiancodebooks. Examples are provided that illustrate the loss in spectral efficiency caused by fast fading and how that loss is amplified when multiple transmit antennas are used. These examples are further enriched by comparisons with the channel capacity under perfect channel-state information at the receiver, and with the spectral efficiency attained by pilot-based transmission.

Per-antenna rate and power control for MIMO layered architectures in the low- and high-power regimes

In a MIMO layered architecture, several codewordsare transmitted from a multiplicity of antennas. Although thespectral efficiency is maximized if the rates of these codewordsare separately controlled, the feedback rate within the linkadaptation loop is reduced if they are constrained to be identical.This poses a direct tradeoff between performance andfeedback overhead. This paper provides analytical expressionsthat quantify the difference in spectral efficiency between bothapproaches for arbitrary numbers of antennas. Specifically, thecharacterization takes place in the realm of the low- and highpowerregimes via expansions that are shown to have a widerange of validity.In addition, the possibility of adjusting the transmit powerof each codeword individually is considered as an alternative tothe separate control of their rates. Power allocation, however,turns out to be inferior to rate control within the context of thisproblem.

Development of In-Situ Detection Methods for Materials-Related Distress (MRD) in Concrete Pavements, July 2003

The purpose of this research was to summarize existing nondestructive test methods that have the potential to be used to detect materials-related distress (MRD) in concrete pavements. The various nondestructive test methods were then subjected to selection criteria that helped to reduce the size of the list so that specific techniques could be investigated in more detail. The main test methods that were determined to be applicable to this study included two stress-wave propagation techniques (impact-echo and spectral analysis of surface waves techniques), infrared thermography, ground penetrating radar (GPR), and visual inspection. The GPR technique was selected for a preliminary round of “proof of concept” trials. GPR surveys were carried out over a variety of portland cement concrete pavements for this study using two different systems. One of the systems was a state-of-the-art GPR system that allowed data to be collected at highway speeds. The other system was a less sophisticated system that was commercially available. Surveys conducted with both sets of equipment have produced test results capable of identifying subsurface distress in two of the three sites that exhibited internal cracking due to MRD. Both systems failed to detect distress in a single pavement that exhibited extensive cracking. Both systems correctly indicated that the control pavement exhibited negligible evidence of distress. The initial positive results presented here indicate that a more thorough study (incorporating refinements to the system, data collection, and analysis) is needed. Improvements in the results will be dependent upon defining the optimum number and arrangement of GPR antennas to detect the most common problems in Iowa pavements. In addition, refining highfrequency antenna response characteristics will be a crucial step toward providing an optimum GPR system for detecting materialsrelated distress.

Mutual Information of IID complex Gaussian signals on block Rayleigh-faded channels

We present a method to compute, quickly and efficiently, the mutual information achieved by an IID (independent identically distributed) complex Gaussian signal on a block Rayleigh-faded channel without side information at the receiver. The method accommodates both scalar and MIMO (multiple-input multiple-output) settings. Operationally, this mutual information represents the highest spectral efficiency that can be attained using Gaussiancodebooks. Examples are provided that illustrate the loss in spectral efficiency caused by fast fading and how that loss is amplified when multiple transmit antennas are used. These examples are further enriched by comparisons with the channel capacity under perfect channel-state information at the receiver, and with the spectral efficiency attained by pilot-based transmission.

Optimum pilot overhead in wireless communication: a unified treatment of continuous and block-fading channels

The optimization of the pilot overhead in wireless fading channels is investigated, and the dependence of this overhead on various system parameters of interest (e.g., fading rate, signal-to-noise ratio) is quantified. The achievable pilot-based spectral efficiency is expanded with respect to the fading rate about the no-fading point, which leads to an accurate order expansion for the pilot overhead. This expansion identifies that the pilot overhead, as well as the spectral efficiency penalty with respect to a reference system with genie-aided CSI (channel state information) at the receiver, depend on the square root of the normalized Doppler frequency. It is also shown that the widely-usedblock fading model is a special case of more accurate continuous fading models in terms of the achievable pilot-based spectral efficiency. Furthermore, it is established that the overhead optimization for multiantenna systems is effectively the same as for single-antenna systems with thenormalized Doppler frequency multiplied by the number of transmit antennas.

Development of a system for 3D high-resolution seismic reflection profiling on lakes

A high-resolution three-dimensional (3D) seismic reflection system for small-scale targets in lacustrine settings has been developed. Its main characteristics include navigation and shot-triggering software that fires the seismic source at regular distance intervals (max. error of 0.25 m) with real-time control on navigation using differential GPS (Global Positioning System). Receiver positions are accurately calculated (error < 0.20 m) with the aid of GPS antennas attached to the end of each of three 24-channel streamers. Two telescopic booms hold the streamers at a distance of 7.5 m from each other. With a receiver spacing of 2.5 m, the bin dimension is 1.25 m in inline and 3.75 m in crossline direction. To test the system, we conducted a 3D survey of about 1 km(2) in Lake Geneva, Switzerland, over a complex fault zone. A 5-m shot spacing resulted in a nominal fold of 6. A double-chamber bubble-cancelling 15/15 in(3) air gun (40-650 Hz) operated at 80 bars and 1 m depth gave a signal penetration of 300 m below water bottom and a best vertical resolution of 1.1 m. Processing followed a conventional scheme, but had to be adapted to the high sampling rates, and our unconventional navigation data needed conversion to industry standards. The high-quality data enabled us to construct maps of seismic horizons and fault surfaces in three dimensions. The system proves to be well adapted to investigate complex structures by providing non-aliased images of reflectors with dips up to 30 degrees.

Modular support for developing mobile ad hoc applications

Abstract This PhD thesis addresses the issue of alleviating the burden of developing ad hoc applications. Such applications have the particularity of running on mobile devices, communicating in a peer-to-peer manner and implement some proximity-based semantics. A typical example of such application can be a radar application where users see their avatar as well as the avatars of their friends on a map on their mobile phone. Such application become increasingly popular with the advent of the latest generation of mobile smart phones with their impressive computational power, their peer-to-peer communication capabilities and their location detection technology. Unfortunately, the existing programming support for such applications is limited, hence the need to address this issue in order to alleviate their development burden. This thesis specifically tackles this problem by providing several tools for application development support. First, it provides the location-based publish/subscribe service (LPSS), a communication abstraction, which elegantly captures recurrent communication issues and thus allows to dramatically reduce the code complexity. LPSS is implemented in a modular manner in order to be able to target two different network architectures. One pragmatic implementation is aimed at mainstream infrastructure-based mobile networks, where mobile devices can communicate through fixed antennas. The other fully decentralized implementation targets emerging mobile ad hoc networks (MANETs), where no fixed infrastructure is available and communication can only occur in a peer-to-peer fashion. For each of these architectures, various implementation strategies tailored for different application scenarios that can be parametrized at deployment time. Second, this thesis provides two location-based message diffusion protocols, namely 6Shot broadcast and 6Shot multicast, specifically aimed at MANETs and fine tuned to be used as building blocks for LPSS. Finally this thesis proposes Phomo, a phone motion testing tool that allows to test proximity semantics of ad hoc applications without having to move around with mobile devices. These different developing support tools have been packaged in a coherent middleware framework called Pervaho.

Disseny pràctic d'un transmissor d'àudio complert utilitzant una modulació AM

RESUM Un transmissor d’AM (modulació per amplitud), utilitza una de les moltes tècniques de modulació existents avui en dia. És molta la importància que té la modulació de senyals i aquests en són alguns exemples: -Facilita la propagació del senyal per cable o per aire. -Ordena l’espectre, distribuint Canals a les diferents informacions. -Disminueix la dimensió de les antenes. -Optimitza l’ample de banda de cada canal. -Evita interferències entre Canals. -Protegeix la informació de les degradacions per soroll. -Defineix la qualitat de la informació transmesa. L’objectiu principal d’aquest treball, serà realitzar un transmissor d’AM utilitzant components electrònics disponibles al mercat. Això es realitzarà mitjançant diversos procediments de disseny. Es realitzarà un procediment de disseny teòric, tot utilitzant els “datasheets” dels diferents components. Es realitzarà un procediment de disseny mitjançant la simulació, gràcies al qual es podrà provar el disseny del dispositiu i realitzar-ne algunes parts impossibles a reproduir teòricament. I finalment es realitzarà el dispositiu a la pràctica. Entre les conclusions més rellevants obtingudes en aquest treball, voldríem destacar la importància de la simulació per poder dissenyar circuits de radiofreqüència. En aquest treball s’ha demostrat que gràcies a una bona simulació, el primer prototip de dispositiu creat ens ha funcionat a la perfecció. D’altre banda, també comentar la importància d’un disseny adequat d’antena per poder aprofitar al màxim el rendiment del nostre dispositiu. Per concloure, la realització d’un aparell transmissor aporta unes nocions equilibrades d’electrònica i telecomunicacions importants per al disseny de dispositius de comunicació.

Ecotoxicological approaches to assess the long-term effects of four anticancer drugs and metabolites on Daphnia pulex

The aquatic environment is exposed continuously and increasingly to chemical substances such as pharmaceuticals. These medical compounds are released into the environment after having being consumed and body-excreted by patients. Pharmaceutical residues are synthetic molecules that are not always removed by traditional sewage treatment processes and thus escape degradation. Among pharmaceuticals that escape sewage treatment plants (STPs), the anticancer drugs were measured in STP effluents and natural waters. In the aquatic environment, their long-term effects at low concentrations are sparsely known on non-target species. Tamoxifen is an anticancer drug that is widely prescribed worldwide for the prevention and treatment of hormone receptor-positive breast cancers. Two of its metabolites, i.e., endoxifen and 4-hydroxy- tamoxifen (4OHTam), have high pharmacological potency in vivo and such as tamoxifen, they are excreted via faeces by patients. Tamoxifen was measured in STP effluents and natural waters but, to the best of our knowledge, its metabolites concentrations in waters have never been reported. Imatinib is another and recent anticancer compound that targets specific tumour cells. This pharmaceutical is also body excreted and because of its increasing use in cancer treatment, imatinib may reach the natural water. The effects of tamoxifen and imatinib are unknown upon more than one generation of aquatic species. And the effects of 4OHTam, endoxifen have never been studied in ecotoxicology so far. The aims of this thesis were threefold. First, the sensitivity of D. pulex exposed to tamoxifen, 4OHTam, endoxifen or imatinib was assessed using ecotoxicological experiments. Ecotoxicology is the science that considers the toxic effects of natural or synthetic substances, such as pharmaceuticals, on organisms, populations, community and ecosystem. Acute and multigenerational (2-4 generations) tests were performed on daphnids considering several studied endpoints, such as immobilisation, size, reproduction, viability and intrinsic rate of natural increase. Additional prospective assays were designed to evaluate whether 1) low concentrations of tamoxifen and 4OHTam were able to induce toxic effects when used in combination, and 2) daphnids were able to recover when offspring were withdrawn from solutions carrying the pharmaceutical. Second, the stability of tamoxifen, 4OHTam and endoxifen in incubation medium was evaluated in solution exempted from daphnids. Because the nominal concentrations of tamoxifen, 4OHTam and endoxifen did not correspond to the measured, we provide a predictive method to estimate the concentrations of these chemicals during long-term ecotoxicological tests. Finally, changes in protein expressions were analysed in D. pulex exposed 2 or 7 seven days to tamoxifen using ecotoxicoproteomic experiments with a shot-gun approach inducing a peptide fractionation step. Our results show that tamoxifen, 4OHTam and endoxifen induced adverse effects in D. pulex at environmentally relevant concentrations. At very low concentrations, these molecules displayed unusual and teratogenic effects because morphological abnormalities were observed in offspring, such as thick and short antennas, curved spines, premature neonates and aborted eggs. Tamoxifen was the most toxic compound among the test chemicals, followed by 4OHTam, endoxifen and imatinib. Tamoxifen no-observed effect concentrations (NOECs) that were calculated for size, reproduction and intrinsic rate were below or in the range of the concentrations measured in natural waters, i.e., between 0.12 µg/L and 0.67 µg/L. For instance, the tamoxifen NOECs that were calculated for reproduction were between 0.67 and 0.72 µg/L, whereas the NOEC was < 0.15 µg/L when based on morphological abnormalities. The NOECs of 4OHTam were higher but still in the same order of magnitude as tamoxifen environmental concentrations, with a value of 1.48 µg/L. Endoxifen NOEC for the intrinsic rate of natural increase (r) and the reproduction were 0.4 and 4.3 µg/L, respectively. Daphnids that were withdrawn from tamoxifen and 4OHTam were not able to recover. Also, the reproduction of D. pulex was reduced when the treated animals were exposed to the combination of tamoxifen and 4OHTam while no effects were observed when these chemicals were tested individually at the same concentration. Among the anticancer drugs that were tested during this thesis, imatinib was the less toxic molecule towards D. pulex. No effects on size and reproduction were observed within two generations, except for the first whose reproduction decreased at the highest test concentration, i.e., 626 µg/L. Our results also underline the need to use measured or predicted concentrations instead of the nominal during aquatic experiments, particularly when lipophilic molecules are tested. Indeed, notable differences between nominal (i.e., theoretical) and measured concentrations were found with tamoxifen, 4OHTam and endoxifen at all test concentrations. A cost and time sustainable method was proposed to predict the test exposure levels of these chemicals during long-term experiments. This predictive method was efficient particularly for low concentrations, which corresponded to the test concentrations in multigenerational tests. In the ecotoxicoproteomic experiments a total of 3940 proteins were identified and quantified in D. pulex exposed to tamoxifen. These results are currently the largest dataset from D. pulex that is published and the results of proteomic analyses are available for the scientific community. Among these 3940 proteins, 189 were significantly different from controls. After protein annotation, we assumed that treated daphnids with tamoxifen had shifted cost-energy functions, such as reproduction, to maintain their basic metabolism necessary to survive. This metabolic cost hypothesis was supported by the presence of proteins involved in oxidative stress. Biomarkers for early detection of tamoxifen harmful effects on D. pulex were not discovered but the proteins of the vitellogenin-2 family (E9H8K5) and the ryanodine receptor (E9FTU9) are promising potential biomarkers because their expression was already modified after 2 days of treatment. In this thesis, the effects of tamoxifen, 4OHTam and endoxifen on daphnids raise questions about the potential impact of tamoxifen and 4OHTam in other aquatic ecosystems, and therefore, about metabolites in ecotoxicology. Because the NOECs were environmentally relevant, these results suggest that tamoxifen and 4OHTam may be interesting pharmaceuticals to consider in risk assessment. Our findings also emphasize the importance of performing long-term experiments and of considering multi-endpoints instead of the standard reproductive endpoint. Finally, we open the discussion about the importance to measure test exposures or not, during ecotoxicological studies. -- Les milieux aquatiques sont exposés continuellement à un nombre croissant de substances chimiques, notamment les médicaments issus de la médecine vétérinaire et humaine. Chez les patients, les substances administrées sont utilisées par le corps avant d'être éliminées par l'intermédiaire des excrétas dans le système d'eaux usées de la ville. Ces eaux rejoignent ensuite une station de traitement afin d'y éliminer les déchets. Dans le cas des molécules chimiques, il arrive que les processus de traitement d'eaux usées ne soient pas suffisamment efficaces et que ces molécules ne soient pas dégradées. Elles sont alors libérées dans le milieu aquatique avec les effluents de la station d'épuration. Une fois dans l'environnement, ces résidus de médicaments sont susceptibles d'induire des effets sur la faune et la flore aquatique, dont les conséquences à long terme et à faibles concentrations sont peu connues. Les anticancéreux sont une famille de médicaments qui peuvent échapper aux traitements des stations d'épuration et qui sont retrouvées dans le milieu aquatique naturel. Parmi ces substances, le tamoxifen est une molécule utilisée dans le monde entier pour prévenir et traiter les cancers hormonaux dépendant du sein, notamment. Une fois ingéré, le tamoxifen est transformé par le foie en métabolites dont deux d'entre eux, le 4-hydroxy-tamoxifen (4OHTam) et l'endoxifen, possèdent un affinité pour les récepteurs aux estrogènes et une efficacité sur les cellules tumorales supérieure au tamoxifen lui- même. Tout comme la molécule mère, ces métabolites sont principalement éliminés par l'intermédiaire des fèces. Le tamoxifen a déjà été mesuré dans les effluents de stations d'épuration et dans les eaux naturelles, mais aucune valeur n'a été reportée pour ses métabolites jusqu'à présent. Un autre anticancéreux, également éliminé par voie biliaire et susceptible d'atteindre l'environnement, est l'imatinib. Cette récente molécule a révolutionné le traitement et la survie des patients souffrant de leucémie myéloïde chronique et de tumeur stromales gastrointestinales. Les effets du tamoxifen et de l'imatinib sur plusieurs générations d'organismes aquatiques, tels que les microcrustacés Daphnia, sont inconnus et le 4OHTam et l'endoxifen n'ont même jamais été testés en écotoxicologie. Cette thèse s'est articulée autour de trois objectifs principaux. Premièrement, la sensibilité des D. pulex exposés au tamoxifen, 4OHTam, endoxifen et imatinib a été évaluée par l'intermédiaire de tests aigus et de tests sur deux à quatre générations. La mobilité, la taille, la reproduction, la viabilité et la croissance potentielle de la population ont été relevées au cours de ces expériences. Des tests supplémentaires, à but prospectifs, ont également été réalisés afin d'évaluer 1) la capacité de récupération des daphnies, lorsque leurs descendants ont été placés dans un milieu exempté de tamoxifen ou de 4OHTam, 2) les effets chez les daphnies exposées à une solution contenant de faibles concentration de tamoxifen et de 4OHTam mélangés. Le deuxième objectif a été d'évaluer la stabilité du tamoxifen, 4OHTam et endoxifen dilué dans le milieu des daphnies. Après analyses, les concentrations mesurées ne correspondaient pas aux concentrations nominales (c.-à-d., théoriques) et il a été nécessaire de développer une méthode efficace de prédiction des niveaux d'exposition lors de tests de longue durée réalisés avec ces trois molécules. Finalement, des changements dans l'expression des protéines chez des daphnies exposées au tamoxifen ont été investigués par l'intermédiaire d'expériences écotoxicoprotéomiques avec une approche dite de shot-gun avec une étape de fractionnement des protéines. Les résultats obtenus dans cette thèse montrent que le tamoxifen, le 4OHTam et l'endoxifen induisent des effets indésirables chez les daphnies à des niveaux d'exposition proches ou identiques aux concentrations du tamoxifen mesurées dans l'environnement, c'est-à-dire 0.12 et 0.67 µg/L de tamoxifen. Ces molécules ont induit des effets inhabituels tels que la production de : nouveau-nés anormaux, avec des antennes et des queues déformées, des prématurés et des oeufs avortés. Le tamoxifen fut la molécule la plus toxique pour les D. pulex suivie du 4OHTam, de l'endoxifen et enfin de l'imatinib. Lors des expériences sur plusieurs générations, les concentrations n'ayant statistiquement pas d'effet (c.à.d. NOEC en anglais) sur la taille, la reproduction et la croissance intrinsèque de la population étaient du même ordre de grandeur que les concentrations environnementales du tamoxifen. Par exemple, les NOECs du tamoxifen calculées pour la reproduction étaient de 0.67 et 0.72 µg/L, tandis que celle calculée sur la base des anomalies chez les nouveau-nés était < 0.15 µg/L. Les NOECs du 4OHTam se situaient entre 0.16 et 1.48 µg/L et celles de l'endoxifen pour la croissance intrinsèque de la population, ainsi que pour la reproduction, étaient de 0.4 et 4.3 µg/L, respectivement. Dans l'expérience basée sur la récupération des daphnies, la taille et la reproduction ont diminué bien que la descendance fût placée dans un milieu sans substances chimiques. Les daphnies exposées au mélange de tamoxifen et de 4OHTam ont produit moins de nouveau-nés que les contrôles, alors que ces concentrations n'ont pas induit d'effets lorsque testées individuellement. Finalement, l'imatinib n'a pas montré d'effets sur les deux générations testées. Seule la première génération exposée à la plus haute concentration (626 µg/L) a montré une diminution de la reproduction. Les résultats obtenus lors de l'évaluation de la stabilité du tamoxifen, 4OHTam et endoxifen dans le milieu des daphnies ont souligné l'importance d'utiliser des concentrations mesurées ou prédites en écotoxicologie. En effet, des différences notables entre concentrations nominales et mesurées ont été observées à toutes les concentrations et l'hypothèse d'un phénomène d'adsorption sur le verre des récipients a été posée. De ce fait, il a été nécessaire d'élaborer une méthode prédictive efficace et acceptable, en terme de temps et de coûts. Une régression polynomiale basée sur des concentrations mesurées et nominales a permis de prédire avec efficacité les faibles niveaux d'exposition utilisés lors d'expériences écotoxicologiques à long terme, sur plusieurs générations. Suite aux expériences d'écotoxicoprotéomiques, un total de 3940 protéines ont été identifiées et quantifiées chez des daphnies exposées au tamoxifen. Ce nombre est actuellement la plus large série de données publiées et mises à disposition pour la communauté scientifique. Parmi ces protéines, 189 sont significatives et possiblement reliées à des processus de reproduction et de stress. Sur cette base, nous avons émis l'hypothèse que les individus subissant un stress, lié à l'exposition au tamoxifen, ont utilisé leur énergie de base pour favoriser leur survie plutôt que la reproduction. Enfin, la détermination de bio-marqueurs exprimant des dommages précoces des daphnies exposées au tamoxifen n'a pas abouti en tant que telle, mais des protéines prometteuses, telle que la famille de viellogenin-2 (E9H8K5) et le récepteur à la ryanodine (E9FTU9), ont été exprimées après deux jours d'exposition déjà. Ces protéines pourraient faire l'objet d'investigations écotoxicoprotéomiques futures. Les résultats de cette thèse posent certaines questions quant au risque du tamoxifen, du 4OHTam et de l'endoxifen sur la faune et la flore aquatique et plus particulièrement sur les anticancéreux présents dans l'environnement. Les effets toxiques de ces molécules ont été observés à des concentrations environnementales et sur plusieurs générations. La question de considérer les métabolites, et ainsi les pro-médicaments, en écotoxicologie est soulevée, notamment parce que ces molécules peuvent être plus actives et efficaces que la molécule mère. Les expériences chroniques, sur plusieurs générations sont également à favoriser car elles offrent un meilleur reflet de la réalité environnementale que des essais aigus ou d'une génération. L'utilisation de la protéomique permet d'agrandir les connaissances sur les effets des médicaments à un niveau inférieur de l'organisation biologique et ainsi, de mieux comprendre de potentiels mécanismes d'action ou de déterminer de potentiels biomarqueurs. Finalement, il semble important de discuter de l'opportunité de mesurer les concentrations qui sont testées en écotoxicologie afin de ne pas sous-estimer le risque pour la faune et la flore aquatique.

Constraints on the permeability structure of alluvial aquifers from the poro-elastic inversion of multi-frequency P-wave velocity logs

We have explored the possibility of obtaining first-order permeability estimates for saturated alluvial sediments based on the poro-elastic interpretation of the P-wave velocity dispersion inferred from sonic logs. Modern sonic logging tools designed for environmental and engineering applications allow one for P-wave velocity measurements at multiple emitter frequencies over a bandwidth covering 5 to 10 octaves. Methodological considerations indicate that, for saturated unconsolidated sediments in the silt to sand range and typical emitter frequencies ranging from approximately 1 to 30 kHz, the observable velocity dispersion should be sufficiently pronounced to allow one for reliable first-order estimations of the permeability structure. The corresponding predictions have been tested on and verified for a borehole penetrating a typical surficial alluvial aquifer. In addition to multifrequency sonic logs, a comprehensive suite of nuclear and electrical logs, an S-wave log, a litholog, and a limited number laboratory measurements of the permeability from retrieved core material were also available. This complementary information was found to be essential for parameterizing the poro-elastic inversion procedure and for assessing the uncertainty and internal consistency of corresponding permeability estimates. Our results indicate that the thus obtained permeability estimates are largely consistent with those expected based on the corresponding granulometric characteristics, as well as with the available evidence form laboratory measurements. These findings are also consistent with evidence from ocean acoustics, which indicate that, over a frequency range of several orders-of-magnitude, the classical theory of poro-elasticity is generally capable of explaining the observed P-wave velocity dispersion in medium- to fine-grained seabed sediments

Development of In Situ Detection Methods for Materials-Related Distress (MRD) in Concrete Pavements: Phase 2, HR-1081, 2005

This project utilized information from ground penetrating radar (GPR) and visual inspection via the pavement profile scanner (PPS) in proof-of-concept trials. GPR tests were carried out on a variety of portland cement concrete pavements and laboratory concrete specimens. Results indicated that the higher frequency GPR antennas were capable of detecting subsurface distress in two of the three pavement sites investigated. However, the GPR systems failed to detect distress in one pavement site that exhibited extensive cracking. Laboratory experiments indicated that moisture conditions in the cracked pavement probably explain the failure. Accurate surveys need to account for moisture in the pavement slab. Importantly, however, once the pavement site exhibits severe surface cracking, there is little need for GPR, which is primarily used to detect distress that is not observed visually. Two visual inspections were also conducted for this study by personnel from Mandli Communications, Inc., and the Iowa Department of Transportation (DOT). The surveys were conducted using an Iowa DOT video log van that Mandli had fitted with additional equipment. The first survey was an extended demonstration of the PPS system. The second survey utilized the PPS with a downward imaging system that provided high-resolution pavement images. Experimental difficulties occurred during both studies; however, enough information was extracted to consider both surveys successful in identifying pavement surface distress. The results obtained from both GPR testing and visual inspections were helpful in identifying sites that exhibited materials-related distress, and both were considered to have passed the proof-of-concept trials. However, neither method can currently diagnose materials-related distress. Both techniques only detected the symptoms of materials-related distress; the actual diagnosis still relied on coring and subsequent petrographic examination. Both technologies are currently in rapid development, and the limitations may be overcome as the technologies advance and mature.

Autonomous Measurements of Bridge Pier and Abutment Scour using Motion-Sensing Radio Transmitters, TR-595, 2010

Two portable Radio Frequency IDentification (RFID) systems (made by Texas Instruments and HiTAG) were developed and tested for bridge scour monitoring by the Department of Civil and Environmental Engineering at the University of Iowa (UI). Both systems consist of three similar components: 1) a passive cylindrical transponder of 2.2 cm in length (derived from transmitter/responder); 2) a low frequency reader (~134.2 kHz frequency); and 3) an antenna (of rectangular or hexagonal loop). The Texas Instruments system can only read one smart particle per time, while the HiTAG system was successfully modified here at UI by adding the anti-collision feature. The HiTAG system was equipped with four antennas and could simultaneously detect 1,000s of smart particles located in a close proximity. A computer code was written in C++ at the UI for the HiTAG system to allow simultaneous, multiple readouts of smart particles under different flow conditions. The code is written for the Windows XP operational system which has a user-friendly windows interface that provides detailed information regarding the smart particle that includes: identification number, location (orientation in x,y,z), and the instance the particle was detected.. These systems were examined within the context of this innovative research in order to identify the best suited RFID system for performing autonomous bridge scour monitoring. A comprehensive laboratory study that included 142 experimental runs and limited field testing was performed to test the code and determine the performance of each system in terms of transponder orientation, transponder housing material, maximum antenna-transponder detection distance, minimum inter-particle distance and antenna sweep angle. The two RFID systems capabilities to predict scour depth were also examined using pier models. The findings can be summarized as follows: 1) The first system (Texas Instruments) read one smart particle per time, and its effective read range was about 3ft (~1m). The second system (HiTAG) had similar detection ranges but permitted the addition of an anti-collision system to facilitate the simultaneous identification of multiple smart particles (transponders placed into marbles). Therefore, it was sought that the HiTAG system, with the anti-collision feature (or a system with similar features), would be preferable when compared to a single-read-out system for bridge scour monitoring, as the former could provide repetitive readings at multiple locations, which could help in predicting the scour-hole bathymetry along with maximum scour depth. 2) The HiTAG system provided reliable measures of the scour depth (z-direction) and the locations of the smart particles on the x-y plane within a distance of about 3ft (~1m) from the 4 antennas. A Multiplexer HTM4-I allowed the simultaneous use of four antennas for the HiTAG system. The four Hexagonal Loop antennas permitted the complete identification of the smart particles in an x, y, z orthogonal system as function of time. The HiTAG system can be also used to measure the rate of sediment movement (in kg/s or tones/hr). 3) The maximum detection distance of the antenna did not change significantly for the buried particles compared to the particles tested in the air. Thus, the low frequency RFID systems (~134.2 kHz) are appropriate for monitoring bridge scour because their waves can penetrate water and sand bodies without significant loss of their signal strength. 4) The pier model experiments in a flume with first RFID system showed that the system was able to successfully predict the maximum scour depth when the system was used with a single particle in the vicinity of pier model where scour-hole was expected. The pier model experiments with the second RFID system, performed in a sandbox, showed that system was able to successfully predict the maximum scour depth when two scour balls were used in the vicinity of the pier model where scour-hole was developed. 5) The preliminary field experiments with the second RFID system, at the Raccoon River, IA near the Railroad Bridge (located upstream of 360th street Bridge, near Booneville), showed that the RFID technology is transferable to the field. A practical method would be developed for facilitating the placement of the smart particles within the river bed. This method needs to be straightforward for the Department of Transportation (DOT) and county road working crews so it can be easily implemented at different locations. 6) Since the inception of this project, further research showed that there is significant progress in RFID technology. This includes the availability of waterproof RFID systems with passive or active transponders of detection ranges up to 60 ft (~20 m) within the water–sediment column. These systems do have anti-collision and can facilitate up to 8 powerful antennas which can significantly increase the detection range. Such systems need to be further considered and modified for performing automatic bridge scour monitoring. The knowledge gained from the two systems, including the software, needs to be adapted to the new systems.

Développement de l'interprétation quantitative de la sismique réflexion lacustre : application de l'AVO aux sédiments quaternaires dans le lac Léman

Résumé Des développements antérieurs, au sein de l'Institut de Géophysique de Lausanne, ont permis de développer des techniques d'acquisition sismique et de réaliser l'interprétation des données sismique 2D et 3D pour étudier la géologie de la région et notamment les différentes séquences sédimentaires du Lac Léman. Pour permettre un interprétation quantitative de la sismique en déterminant des paramètres physiques des sédiments la méthode AVO (Amplitude Versus Offset) a été appliquée. Deux campagnes sismiques lacustres, 2D et 3D, ont été acquises afin de tester la méthode AVO dans le Grand Lac sur les deltas des rivières. La géométrie d'acquisition a été repensée afin de pouvoir enregistrer les données à grands déports. Les flûtes sismiques, mises bout à bout, ont permis d'atteindre des angles d'incidence d'environ 40˚ . Des récepteurs GPS spécialement développés à cet effet, et disposés le long de la flûte, ont permis, après post-traitement des données, de déterminer la position de la flûte avec précision (± 0.5 m). L'étalonnage de nos hydrophones, réalisé dans une chambre anéchoïque, a permis de connaître leur réponse en amplitude en fonction de la fréquence. Une variation maximale de 10 dB a été mis en évidence entre les capteurs des flûtes et le signal de référence. Un traitement sismique dont l'amplitude a été conservée a été appliqué sur les données du lac. L'utilisation de l'algorithme en surface en consistante a permis de corriger les variations d'amplitude des tirs du canon à air. Les sections interceptes et gradients obtenues sur les deltas de l'Aubonne et de la Dranse ont permis de produire des cross-plots. Cette représentation permet de classer les anomalies d'amplitude en fonction du type de sédiments et de leur contenu potentiel en gaz. L'un des attributs qui peut être extrait des données 3D, est l'amplitude de la réflectivité d'une interface sismique. Ceci ajoute une composante quantitative à l'interprétation géologique d'une interface. Le fond d'eau sur le delta de l'Aubonne présente des anomalies en amplitude qui caractérisent les chenaux. L'inversion de l'équation de Zoeppritz par l'algorithme de Levenberg-Marquardt a été programmée afin d'extraire les paramètres physiques des sédiments sur ce delta. Une étude statistique des résultats de l'inversion permet de simuler la variation de l'amplitude en fonction du déport. On a obtenu un modèle dont la première couche est l'eau et dont la seconde est une couche pour laquelle V P = 1461 m∕s, ρ = 1182 kg∕m3 et V S = 383 m∕s. Abstract A system to record very high resolution (VHR) seismic data on lakes in 2D and 3D was developed at the Institute of Geophysics, University of Lausanne. Several seismic surveys carried out on Lake Geneva helped us to better understand the geology of the area and to identify sedimentary sequences. However, more sophisticated analysis of the data such as the AVO (Amplitude Versus Offset) method provides means of deciphering the detailed structure of the complex Quaternary sedimentary fill of the Lake Geneva trough. To study the physical parameters we applied the AVO method at some selected places of sediments. These areas are the Aubonne and Dranse River deltas where the configurations of the strata are relatively smooth and the discontinuities between them easy to pick. A specific layout was developed to acquire large incidence angle. 2D and 3D seismic data were acquired with streamers, deployed end to end, providing incidence angle up to 40˚ . One or more GPS antennas attached to the streamer enabled us to calculate individual hydrophone positions with an accuracy of 50 cm after post-processing of the navigation data. To ensure that our system provides correct amplitude information, our streamer sensors were calibrated in an anechoic chamber using a loudspeaker as a source. Amplitude variations between the each hydrophone were of the order of 10 dB. An amplitude correction for each hydrophone was computed and applied before processing. Amplitude preserving processing was then carried out. Intercept vs. gradient cross-plots enable us to determine that both geological discontinuities (lacustrine sediments/moraine and moraine/molasse) have well defined trends. A 3D volume collected on the Aubonne river delta was processed in order ro obtain AVO attributes. Quantitative interpretation using amplitude maps were produced and amplitude maps revealed high reflectivity in channels. Inversion of the water bottom of the Zoeppritz equation using the Levenberg-Marquadt algorithm was carried out to estimate V P , V S and ρ of sediments immediately under the lake bottom. Real-data inversion gave, under the water layer, a mud layer with V P = 1461 m∕s, ρ = 1182 kg∕m3 et V S = 383 m∕s.