Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Fabrico, controlo de qualidade e colocação de mistura betuminosa em obra

Este relatório traduz o trabalho realizado na empresa Cimalha, Construções da Batalha S.A., durante 5 meses de estágio curricular. O relatório inicia-se com uma descrição da empresa e uma apresentação dos objetivos propostos para o estágio. Estes centram-se essencialmente nas questões inerentes ao controlo de qualidade do processo de fabrico e aplicação de misturas betuminosas. Este aspeto é de extrema relevância dado que é importante garantir que os investimentos realizados na construção de estradas tenham um controlo da qualidade adequado de modo a garantir a durabilidade pretendida e condições satisfatórias para a utilização [1]. Efetua-se a descrição das atividades realizadas, os ensaios realizados e análise dos resultados obtidos. Os ensaios e procedimentos seguiram vários documentos normativos, nacionais e estrangeiros, destacando-se o Caderno de Encargos Tipo Obra (CETO) publicado em Fevereiro de 2009 pela Estadas de Portugal, S. A. (EP) [2] atual Infraestruturas de Portugal, S. A. (IP) [3]. O estágio revelou-se como sendo uma importante componente da formação permitindo a consolidação e aplicação prática da formação teórica na área de atuação da empresa.

Determinação simultânea de Glicerol livre e total, MONO-, DI e triglicerídeos em biodiesel etílico de girassol, mamona e da mistura de sebo e soja empregando GC-FID

O biodiesel produzido para ser comercializado no Brasil deve estar de acordo aos padrões de qualidade estabelecidos pela resolução de 4 de fevereiro de 2010 da Agência Nacional do Petróleo, Gás Natural e do Biocombustível (ANP, 04/2010). Neste trabalho, foi estudada a aplicação dos métodos ASTM D 6584 e EN 14105 para o biodiesel de mamona e biodiesel oriundo de rota etílica. Ambos os métodos empregam GC (Cromatografia Gasosa, do inglês Gas Chromatography) com FID (Detecção por Ionização em Chama, do inglês Flame Ionization Detection) e reação de sililação com N-metil-N-(trimetilsilil)trifluoracetamida (MSTFA). Os compostos foram identificados para quantificação pelos tempos de retenção, para os diglicerídeos e triglicerídeos foram utilizadas bandas de tempo de retenção. Os parâmetros de validação considerados foram: curva analítica, linearidade, sensibilidade, robustez, precisão e exatidão. Os métodos ASTM D 6584 e EN 14105 apresentaram sensibilidade semelhante para todos os compostos. Foram escolhidas as condições cromatográficas estabelecidas pelo método ASTM D 6584 por ser mais rápido que o EN14105 e ter sensibilidade semelhante. O método apresentou boa linearidade com todas as curvas analíticas com r maiores que 0,999. A reação de sililação com MSTFA foi otimizada para o biodiesel etílico de mamona em virtude da sua composição química. Um volume de 500 μL de MSTFA foi escolhido para realização dos ensaios de exatidão e precisão. Os valores de exatidão ficaram entre 67 e 145,9% com valores de precisão menores que 11%. Foi avaliada a ocorrência de efeito matriz para biodiesel etílico de mamona, sendo que esse efeito foi considerado baixo para glicerol, monooleína e dioleína e médio para trioleína. Mesmo havendo efeito de matriz o preparo das curvas analíticas em solvente conforme sugerido pelos métodos de referência foi mantido. O método foi robusto frente às variações da composição química da matriz. Na aplicação do método, esse se mostrou adequado para amostras de biodiesel etílico de mamona, de girassol e da mistura de sebo e soja.

Desevolvimento de nanocompósitos de poli(metacrilato de metila)/argila processados por mistura no estado fundido

Poly(methyl methacrylate)/clay nanocomposites were prepared by melt mixing using a montmorillonite-rich clay (MMT). The clay in natura was treated with acrylic acid to facilitate the dispersion in the polymer matrix. A masterbatch of PMMA/clay was prepared and combined with the pure PMMA and then subjected to extrusion process using singlescrew and twin-screw extruders followed by injection. Nanocomposites were processed with clay contents of 1, 3, 5 and 8 wt.%. The effect of shear processing on the morphology of the nanocomposites was evaluated by XRD, SEM and TEM. Thermal and mechanical properties of the nanocomposites were investigated through TGA, DSC, HDT, VICAT, tensile and impact tests, to evaluate the effect of the addition of clay to the PMMA matrix. Flammability tests were also conducted to investigate the effect of the addition of clay on the flame retardation properties. SEM images of the nanocomposites indicated the presence of clay agglomerates, which resulted in the reduction of properties such as thermal stability, mechanical strength and impact resistance, and increased the rate of burning for materials processed by both extrusion routes

Desempenho de novilhos suplementados no periodo seco com mistura multipla a base de leucena no semi-arido brasileiro.

O estudo objetivou avaliar uma mistura multipla composta de feno de folhas de leucena (Leucaena leucocephala (Lam.) de Wit.), raspa de mandioca e uma mistura mineral, como suplemento para novilhos azebuados, no periodo seco. A mistura foi comparada com duas outras alternativas de suplementacao: a mistura sal-ureia e a silagem de leucena. Os animais dos tres grupos pastejaram, conjuntamente, em capim buffel (Cenchrus ciliaris, L.). Ao final dos 84 dias do periodo experimental, o incremento em peso vivo nos animais submetidos a mistura multipla (22,1 kg/cab) nao diferiu (P>0,05) do observado nos animais suplementados com silagem de leucena (17,7 kg/cab), mas correspondeu (P<0,05) a quase cinco vezes o observado nos animais submetidos a mistura sal-ureia (4,6 kg/cab).

Bioensaio para avaliação de recuperação de nitrogênio contido em compostos obtidos a partir da mistura de palhada de gramínea e de leguminosa.

A compostagem constitui-se importante alternativa para obtenção de fertilizantes orgânicos, que são utilizados como condicionadores de solo e fornecedores de nutrientes, principalmente do nitrogênio (N), em diversos sistemas de produção agrícola. O objetivo deste trabalho foi avaliar a capacidade de recuperação biológica do N contido em diferentes formulações de compostos obtidos a partir da mistura de palhada de capim Napier e de Crotalaria juncea. Avaliou-se também a capacidade de recuperação do N de outros adubos. O bioensaio foi realizado em casa de vegetação, utilizando-se vasos plásticos de 650 ml com coletores de água lixiviada. Como planta indicadora, foi utilizado o Milheto Pérola (Pennisetum glaucum). Compostos orgânicos com maiores teores de N e menores relações C:N proporcionaram maiores taxas de recuperação de N pelo Milheto Pérola.

Características físicas e mecânicas de misturas de solo, cimento e cinzas de bagaço de cana-de-açúcar

This work was done with the objective of studying some physical and mechanical characteristics of the sugarcane bagasse ash added to a soil-cement mixture, in order to obtain an alternative construction material. The sugarcane bagasse ash pre-treatment included both sieving and grinding, before mixing with soil and cement. Different proportions of cement-ash were tested by determining its standard consistence and its compressive resistance at 7 and 28 days age. The various treatments were subsequently applied to the specimens molded with different soil-cement-ash mixtures which in turns were submitted to compaction, unconfined compression and water absorption laboratory tests. The results showed that it is possible to replace up to 20% of Portland cement by sugarcane bagasse ash without any damage to the mixture's compressive strength.

Características físicas e mecânicas de misturas de solo, cimento e casca de arroz

The main objective of this work is the study of the effect of rice husk addition on the physical and mechanical properties of soil-cement, in order to obtain an alternative construction material. The rice husk preparation consisted of grinding, sieving, and the pre-treatment with lime solution. The physical characteristics of the soil and of the rice husk were determined. Different amounts of soil, cement and rice husk were tested by compaction and unconfined compression. The specimens molded according to the treatments applied to the mixtures were subsequently submitted to compression testing and to tensile splitting cylinder testing at 7 and 28 days of age and to water absorption testing. After determining its physical and mechanical characteristics, the best results were obtained for the soil + 12% (cement + rice husk) mixture. The results showed a promising use as an alternative construction material.

Efeito da adição de cinza da casca de arroz em misturas cimento-casca de arroz

The rice husk and its ash are abundant and renewable and can be used to obtain alternative building materials. An increase in the consumption of such waste could help minimize the environmental problems from their improper disposal. This study aimed to evaluate the use of ashes as a cargo mineral (filler). However, the rice husk chemically interferes in the conduct of the based cement mixtures. Thus, different mixes cement-rice husk with and without the addition of ash were evaluated in order to highlight the influence of its components (husk; ash), which could otherwise be excluded or be underestimated. Cylindrical samples (test of simple compression and traction by diametrical compression) and samples extracted from manufactured pressed board (test of bending and parallel compression to the surface), were used to evaluate the behavior of different mixtures of components (rice hush; RHA - rice husk ahs). The results of the mechanical tests showed, in general, there is not a statistical difference between the mixtures, which are associated with the chemical suppressive effect of the rice husk ash. The mixture of rice husk of 10 mm, with an addition of 35% of the rice husk ash, is notable for allowing the highest consumption of rice husk and rice husk ash, to reduce 25% the consumption of cement and to allow the storage (without emissions to the atmosphere), around 1.9 ton of CO2 per ton of cement consumed, thus contributing to the reduction of CO2 emissions, which can stimulate rural constructions under an ecological point of view.

Composição florística de uma floresta ripária na Reserva Estadual de Porto Ferreira, SP

The point-centred quarter method (63 points) was applied in Porto Ferreira State Reserve (21º49'S and 47º25'W) in an area (1.08ha) on the right margin of Moji Guaçu river, including two woody individuals per quarter - one with DBH < 10cm and at least 130cm high, the other with DBH > 10cm. The results obtained were compared with those published by other authors for a riparian forest (Mata da Figueira) at Moji Guaçu Ecological Station (about 100 km upstream on the same river). At Porto Ferreira 107 species were found, of which 80 were exclusive, compared with the Mata da Figueira where of the 59 species listed, 31 were exclusive. The two area shared 27 common species, thus accounting for a low Sørensen similarity of 48.6%. The great environmental heterogeneity of the floodplains, as well as the degree of anthropic disturbance, could account for this floristic variation. The greatest numbers of species were shown by Leguminosae (20), Myrtaceae (17), Rutaceae (9), Euphorbiaceae (7), and Lauraceae, Meliaceae, Moraceae and Rubiaceae (6 species each). There appears to be little difference at the family level among the periodically flooded and non-flooded forests of the State of São Paulo, but the species show different degreees of preference for habitat. The floristic composition of the two areas presented a mixture of typical species with others of non-flooded forests. The latter would occur on the floodplain probably by a) adaptation of the root system to relatively short flooding periods; b) shorter periods of flooding on the higher points of the microrelief of the floodplain, and c) greater aeration due to running water.

Avaliação da aceitação de vinhos brancos varietais brasileiros através de testes sensoriais afetivos e técnica multivariada de mapa de preferência interno

The acceptability of nine commercial brazilian varietal white table wines (Riesling, Chardonnay and Gewürztraminer) was evaluated using sensory affective tests. The samples were assessed by 43 consumers of brazilian white wines using he nine-point structured hedonic scale. Judges were recruited based on their responses to a questionnary about consumer?s behavior towards white wines consumption. Subsequently, Analysis of Variance (ANOVA) with means comparision (Tukey test) and Internal Analysis of Preference Mapping (MDPREF) were performed on data. Analysis of Variance showed that two samples (a Riesling and a Gewürztraminer, both sweet table wines) had significantly (p < 0.05) higher acceptance means, around 7 in the hedonic scale. The least acceptance means (4,3) was obtained by a demi-sec Chardonnay wine and the other six samples achieved means around 5 in the hedonic scale, all of them either demi-sec or dry table wines. MDPREF confirmed the results showed by ANOVA showing that samples were segmented into two groups of preference. The first group was composed by 86% of consumers who prefered the sweet table wines (higher acceptance), converging to the region on the map where these samples were represented. Only 14% showed preference for the demi-sec and dry table wines, being represented on the region of the MDPREF where these samples were located. This study suggests that sweet table wines are prefered by Brazilian consumers, instead of dry or demi-sec table wines.

Perfil sensorial de vinhos brancos varietais brasileiros através de análise descritiva quantitativa

Descriptive terminology and sensory profile of three varieties of brazilian varietal white wines (cultivars Riesling, Gewürztraminer and Chardonnay) were developed by a methodology based on the Quantitative Descriptive Analysis (QDA). The sensory panel consensually defined the sensory descriptors, their respective reference materials and the descriptive evaluation ballot. Ten individuals were selected as judges based on their discrimination, reproducibility and individual consensus with the sensory panel. Twelve descriptors were generated showing similarities and differences among the wine samples. Each descriptor was evaluated using a nine-centimeters non-structured scale with the intensity terms anchored at its ends. The collected data were analysed by ANOVA, Tukey test and Principal Component Analysis (PCA). The results showed a great difference within the sensory profile of Riesling and Gewürztraminer wines, whereas Chardonnay wines showed a lesser variation. PCA separated samples into two groups: a first group formed by wines higher in sweetness and fruitty flavor and aroma; and a second group of wines higher in sourness, adstringency, bitterness, alcoholic and fermented flavors.

Programação esportiva na TV Brasil : a influência da ideologia e indústria cultural

Universidade Estadual de Campinas . Faculdade de Educação Física

Homo-motor, ciborgues e... aha! pessoas : da revolução industrial a revolução da informação

Universidade Estadual de Campinas . Faculdade de Educação Física