Spectroscopic study of the penetration depth of grafted polystyrene onto poly (tetrafluoroethylene-co-perfluoropropylvinylether) substrates. 1. Effect of grafting conditions

This study concerns the radiation grafting of styrene onto poly(tetrafluoroethylene-co-perfluoropropylvinylether) (PFA) substrates and the penetration depth of the graft. Grafting was obtained by the simultaneous irradiation method, and the spectroscopic analysis was made with the micro-Raman technique. Effects of grafting conditions such as the type of solvent, dose rate, and irradiation dose on the grafting yield were investigated. Of the different solvents used, the most efficient in terms of increasing grafting yield were dichloromethane, benzene, and methanol, respectively. A mixture of methanol and dichloromethane used as a solvent for styrene achieved a higher degree of grafting and concentration of grafted polystyrene onto the surface of PFA substrates than solutions of the monomer in the separate solvents. The degree of grafting increased with increasing radiation dose up to 500 kGy, stabilizing above this dose. However, the grafting yield decreased with an increase in the dose rate. The increase in the overall grafting yield was accompanied by a proportional increase in the penetration depth of the grafts into the substrate. (C) 2002 Wiley Periodicals, Inc.

In vivo and in vitro toxicities of pithraj and neem against rice green leafhopper (Nephotettix cincticeps Uhler)

Seed extracts of Aphanamixis polystachya Wall et Parker (pithraj) and Azadirachta indica A. Juss (neem) were evaluated for their in vivo and in vitro toxicity to Nephotettix cincticeps Uhler (rice green leafhopper). Crude extracts from both plants showed toxicity to leafhopper. Among them, the methanol extract of pithraj (MCX) was most toxic and showed 95% mortality effects at 72 h after treatment (HAT), followed by neem (74%). When LD50's were compared, it was found that the neem extract possessed the highest toxicity (LD50 16.59 μg/insect) at 72 HAT. Both the pithraj (MCX) and neem extracts showed their enzyme inhibition effectiveness against rice green leafhopper. The highest inhibition rate (IR) was caused by neem (60%) at the concentration of 2.0 mg/ml, followed by MCX (47%). The lowest IR50 value (0.97 mg/ml) was observed in neem at 30 min.

Finite, three-dimensional adsorbed phase growth in activated carbon mesopores

The role of PACs (primary adsorption centers) in the mesopore (i.e., transport) region of activated carbons during adsorption of polar species, such as water, is unclear. A classical model of three-dimensional adsorption on finite PACs is presented. The model is a preliminary, theoretical investigation into adsorption on mesopore PACs and is intended to give some insight into the energetic and physical processes at work. Work processes are developed to obtain isotherms and three-dimensional sorbate growth on PACs of varying size and energetic characteristics. The work processes allow two forms of adsorbed phase growth: densification at constant boundary and boundary growth at constant density. Relatively strong sorbate-sorbent interactions and strong surface tension favor adsorbed phase densification over boundary growth. Conversely, relatively weak sorbate-sorbent interactions and weak surface tension favor boundary growth over densification. If sorbate-sorbate interactions are strong compared to sorbate-sorbent interactions, condensation with hysteresis occurs. This can also give rise to delayed boundary growth, where all initial adsorption occurs in the monolayer only. The results indicate that adsorbed phase growth on PACs may be quite complex.

Effects of adsorbate-adsorbate interaction in the description of adsorption isotherm of hydrocarbons in micro-mesoporous carbonaceous materials

In this paper, we present a model accounting for the adsorbate-adsorbate interaction in the adsorbed phase in the description of adsorption of pure vapors on carbonaceous materials. The details of the adsorbate-adsorbate interaction of a particular species are obtained from the analysis of its adsorption data on non-porous carbon black. The predictability of the model is tested against the adsorption isotherm data for benzene, toluene, n-pentane, n-hexane, carbon tetrachloride, methanol and ethanol on microporous activated carbon. It was found that the model prediction for non-polar adsorbates are satisfactory while it under-predicts for polar adsorbates, which is attributed to their additional interaction with functional groups. (C) 2002 Elsevier Science B.V. All rights reserved.

Identification of slow and fast-acting toxins in a highly ciguatoxic barracuda (Sphyraena barracuda) by HPLC/MS and radiolabelled ligand binding

A barracuda implicated in ciguatera fish poisoning in Guadeloupe was estimated to have an overall flesh toxicity of 15 MUg/g using mouse bioassay. A lipid soluble extract was separated into two toxic fractions, FrA and FrB, on a LH20 Sephadex column eluted with dichloromethane/methanol (1:1). When intraperitoneal injected into mice, FrA provoked symptoms characteristic of slow-acting ciguatoxins, whereas FrB produced symptoms indicative of fast-acting toxins (FAT). High performance liquid chromatography/mass spectrometry/radio-ligand binding (HPLC/MS/RLB) analysis confirmed the two fractions were distinct, because only a weak overlap of some compounds was observed. HPLC/MS/RLB analysis revealed C-CTX-1 as the potent toxin present in FrA, and two coeluting active compounds at m/z 809.43 and 857.42 in FrB, all displaying the characteristic pattern of ion formation for hydroxy-polyethers. Other C-CTX congeners and putative hydroxy-polyether-like compounds were detected in both fractions, however, the RLB found them inactive. C-CTX-1 accounted for >90% of total toxicity in this barracuda and was confirmed to be a competitive inhibitor of brevetoxin binding to voltage-sensitive sodium channels (VSSCs) with a potency two-times lower than P-CTX-1. However, FAT active on VSSCs and

Comparative study of the radiation-induced grafting of styrene onto poly(tetrafluoroethylene-co-perfluoropropylvinyl ether) and polypropylene substrates. I: Kinetics and structural investigation

A comparative study has been made of the radiation grafting of styrene onto poly(tetrafluoroethylene-co-perfluoropropyl vinyl ether) (PFA) and polypropylene (PP) substrates, using the simultaneous irradiation method. Effects of grafting conditions such as monomer concentrations, type of solvent, dose rate and irradiation dose on the grafting yield were investigated. Under the same grafting conditions it was found that a higher degree of grafting of styrene was obtained using a mixture of dichloromethane/methanol solvents for PFA and methanol for PP and the degree of grafting was higher in PP than in PFA at all doses. However, the micro-Raman spectroscopy analysis of the graft revealed that, for the same degree of grafting, the penetration depth of the grafted polystyrene into the substrate was higher in PFA than in PP substrates. In both polymers the crystallinity was hardly affected by the grafting process and the degree of crystallinity decreased slightly with grafting dose. The dependence of the initial rate of grafting on the dose rate and the monomer concentration was found to be 0.6 and 1.4 order for PFA and 0.15 and 2.2 for PP, respectively. The degree of grafting increased with increasing radiation dose in both polymers. However, the grafting yield decreased with an increase in the dose rate. The increase in the overall grafting yield for PFA and PP was accompanied by a proportional increase in the penetration depth of the graft into the substrates. (C) 2003 Society of Chemical Industry.

Investigation of the vapor-phase grafting of styrene onto PFA

Poly(tetrafluoroethylene-co-perfluoropropyI vinyl ether), PFA, was grafted with styrene from the vapor phase using a simultaneous radiation grafting method. The graft yields were measured as a function of the dose and dose rate and were found to be initially linearly dependent on the dose and independent of the dose rate up to dose rates of similar to3 kGy/h. However, at a dose rate of 6.2 kGy/h, the slope of the yield-grafting time plot decreased. Raman depth profiles of the grafts showed that the polystyrene concentrations were greatest near the surface of the grafted samples and decreased with depth. The maximum penetration depth of the graft depended on the radiation dose for a fixed dose rate. Fmoc-Rink loading tests showed that the grafts displayed superior loading compared to grafts prepared from bulk styrene or from styrene solutions other than methanol.

Influência dos estrativos na resistência ao apodrecimento de seis espécies de madeira

O presente trabalho teve como objetivo avaliar o efeito da extração da madeira de seis espécies, quatro nativas (candeia, cedro, cerejeira e jacarandá-caviúna) e duas exóticas (E. citriodora e E. gumifera), em diferentes solventes, na resistência ao apodrecimento causado pelo fungo da podridão-parda Gloeophyllum trabeum. O material foi ensaiado na forma de serragem, em face da maior facilidade para os procedimentos de extração. Dentre os resultados, pode-se destacar a baixa perda de massa ocorrida na madeira de cedro (Cedrela fissilis), evidenciando sua elevada resistência natural ao fungo testado e, ainda, à incapacidade dos solventes utilizados na retirada de compostos que conferem resistência ao apodrecimento. As madeiras de candeia (Vanillosmopsis erythropappa), cerejeira (Amburana cearensis), jacarandá-caviúna (Machaerium scleroxylon) e de eucaliptos (Corymbia citriodora e Eucalyptus gummifera) também apresentaram elevada resistência natural, em função da baixa perda de massa ocorrida, quando expostas ao fungo G. trabeum. Essas madeiras, quando totalmente extraídas, apresentaram elevados valores de perda de massa. No que diz respeito ao material extraído por diferentes solventes de forma isolada, observou-se, na candeia, que o solvente mais eficiente na retirada de substâncias que conferem resistência ao apodrecimento foi o diclorometano. Com relação ao cedro, o mais eficiente foi o metanol. Na cerejeira, por meio da mistura de etanol/tolueno retiraram-se mais substâncias, ao passo que no jacarandá-caviúna foi o metanol. Nas madeiras de eucaliptos, o metanol foi mais eficiente na retirada de componentes tóxicos ao fungo utilizado neste estudo, devendo destacar ainda, no E. gummifera, a eficiência da água quente na retirada de tais compostos. No C. citriodora, os valores de perda de massa, em razão das extrações em água fria, em água quente, em diclorometano e ao natural (não-extraída), foram muito baixos.

A síntese do aduto binuclear [Fe(CNBut)(CO)4(HgSO4 )]

The binuclear [Fe(CNBut)(CO)4(HgSO4 )] adduct was obtained in the reaction of HgSO4 with [Fe(CNBut)(CO)4] in methanol. This adduct, without a similar in the homoleptic pentacarbonyliron, was characterized by analytical and spectroscopic data. Further Mössbauer and molar conductivity studies have confirmed it's adduct nature.

Efeitos da depleção de nitrogênio sobre a biomassa e produção lipídica lipídica de três espécies de microalgas fitoplânticas

O uso de lipídios obtidos a partir da biomassa de microalgas tem sido descrito como uma alternativa promissora para a indústria petro-diesel e envolve etapas como o cultivo de microalgas, separação da biomassa e extração de lipídios. Para viabilizar a produção em larga escala, é necessário selecionar as espécies mais produtivas, diminuir os custos de produção e determinar as condições ideais de cultivo. Os gêneros Chlorella, Desmodesmus e Ankistrodesmus apresentam características favoráveis à produção comercial, tendo sido então selecionada uma espécie de cada no presente trabalho. O objetivo do estudo foi avaliar diferentes condições de cultivo de Ankistrodesmus fusiformis, Chlorella vulgaris e Desmodesmus spinosus visando o aumento da produtividade em biomassa e lipídios totais. As algas foram identificadas e cultivadas em laboratório, em condições controladas de temperatura a 26ºC (±1), aeração por borbulhamento à pressão ambiente e luminosidade fornecida por lâmpadas fluorescentes, com intensidade de 47,25 μmol de fótons m-2.s-1 (3500 lux), fotoperiodo de 12h e pH 7, sob duas concentrações estressantes de nitrato de sódio (0,10 g/L e 0,05g/L). Os cultivos duraram em média 16 dias, sendo as curvas de crescimento construídas com dados de espectrofotometria óptica coletados a cada 48h, e a biomassa obtida ao final do cultivo por centrifugação e liofilização de cada unidade experimental. Para extração dos lipídios totais, foi utilizada a mistura de clorofórmio: metanol (1:2), segundo a metodologia de Bligh & Dyer (1959). Os tratamentos de estresse em D.spinosus resultaram em maior acúmulo lipídico, com aumento de até 149,7%, porém com drástica diminuição do crescimento e biomassa. Em C. vulgaris, nos tratamentos de estresse, verificou-se apenas ligeiro aumento do peso seco e teor de lipídios, não havendo diferença significativa entre os tratamentos e o controle. Da mesma forma, A.fusiformis não mostrou respostas significativas ao estresse pela redução de nitrato de sódio do meio, havendo ligeira diminuição do conteúdo lipídico e aumento do crescimento e biomassa. Com respostas diferentes para cada espécie estudada, evidencia-se a necessidade do conhecimento da fisiologia e autoecologia da cepa a ser cultivada em escala comercial visando à produção de ácidos graxos para fins de biodiesel.

Estudo químico e biológico em alcaloides de Hippeastrum aulicum (KER GAWL.) HERB. : uma espécie da família Amaryllidaceae

As espécies da família Amaryllidaceae estão distribuídas em regiões quentes e temperadas ao redor do mundo. Essa família produz um grupo bem conhecido de alcaloides, os isoquinolínicos, que demonstram ampla variedade de atividades biológicas, assim como antiviral, anticâncer, inibição da acetilcolinesterase (AChE), antimalárica, entre outras. Nesse trabalho, são relatados o estudo químico dos alcaloides presentes na espécie brasileira Hippeastrum aulicum e a investigação de atividades antiparasitárias contra Trypanosoma cruzi e Leishmania infantum dos alcaloides isolados. Para tanto, foi realizada extração ácido-base dos extratos metanólicos de bulbos e folhas de H. aulicum, seguida por técnicas cromatográficas de separação, com o objetivo de isolar os alcaloides presentes na espécie. Foram obtidos 11 alcaloides: haemantamina (1), albomaculina (2), haemantidina (3), 6- epihaemantidina (4), N-óxido haemantamina (5), 7-metoxi-O-metillicorenina (6), aulicina (7), licorina (8), trisfaeridina (9), galantina (10) e norpluvina (11). O N-óxido haemantamina é relatado pela primeira vez a partir de fonte natural e nesse trabalho foi totalmente caracterizado por métodos espectrométricos e espectroscópicos. Os alcaloides 1, 2, 6, 7 e 8 foram testados in vitro contra os parasitas Trypanosoma cruzi e Leishmania infantum em diferentes concentrações e haemantamina (1) apresentou-se como importante agente contra a forma promastigota de L. infantum com IC50 de 0,6 M, enquanto 7-metoxi-O-metillicorenina (6) mostrou atividade contra a forma tripomastigota de T.cruzi, sendo mais ativo (IC50 = 89,55 M) e mais seletivo (IS > 2,2) que o padrão utilizado (benzonidazol, IC50 = 440,7 M, IS = 1,0).

Electrospun silk-elastin-like fiber mats for tissue engineering applications

Protein-based polymers are present in a wide variety of organisms fulfilling structural and mechanical roles. Advances in protein engineering and recombinant DNA technology allow the design and production of recombinant protein-based polymers (rPBPs) with an absolute control of its composition. Although the application of recombinant proteins as biomaterials is still an emerging technology, the possibilities are limitless and far superior to natural or synthetic materials, as the complexity of the structural design can be fully customized. In this work, we report the electrospinning of two new genetically engineered silk-elastin-like proteins (SELPs) consisting of alternate silk- and elastin-like blocks. Electrospinning was performed with formic acid and aqueous solutions at different concentrations without addition of further agents. The size and morphology of the electrospun structures was characterized by scanning electron microscopy showing to be dependent of concentration and solvent used. Treatment with air saturated with methanol was employed to stabilize the structure and promote water insolubility through a time-dependent conversion of random coils into β-sheets (FTIR). The resultant methanol-treated electrospun mats were characterized for swelling degree (570-720%), water vapour transmission rate (1083 g/m2/day) and mechanical properties (modulus of elasticity of ~126 MPa). Furthermore, the methanol-treated SELP fiber mats showed no cytotoxicity and were able to support adhesion and proliferation of normal human skin fibroblasts. Adhesion was characterized by a filopodia-mediated mechanism. These results demonstrate that SELP fiber mats can provide promising solutions for the development of novel biomaterials suitable for tissue engineering applications.

Cytogenetic and identification of the nucleolus organizer region in Heliconia bihai (L.) L.

The genus Heliconia is not much studied and the number of existing species in this genus is still uncertain. It is known that this number relies between 150 to 250 species. In Brazil, about 40 species are native and known by many different names. The objective of this paper was to characterize morphometrically and to identify the NOR (active nucleolus organizer regions) by Ag-NOR banding of chromosomes of Heliconia bihai (L) L. Root meristems were submitted to blocking treatment in an amiprofos-methyl (APM) solution, fixed in methanol-acetic acid solution for 24 hours, at least. The meristems were washed in distilled water and submitted to enzymatic digestion with pectinase enzyme. The slides were prepared by dissociation of the root meristem, dried in the air and also on hot plate at 50°C. Subsequently, some slides were submitted to 5% Giemsa stain for karyotype construction and to a solution of silver nitrate (AgNO3) 50% for Ag-NOR banding. The species H. bihai has 2n = 22 chromosomes, 4 pairs of submetacentric chromosomes and 7 pairs of metacentric chromosomes, and graded medium to short (3.96 to 0.67 μM), with the presence of active NOR in pairs 1 and 2 and interphase cells with 2 nucleoli. These are the features of a diploid species.

New heterogeneous catalysts for trans-esterification of triglycerides

This paper describes preliminary work done towards the development of new metallic heterogeneous catalysts to be used in the transesterification reaction of triglycerides, which is of considerable interest in the production of biodiesel. Biodiesel, is a mixture of mono-alkyl esters of fatty acids, and is currently manufactured by transesterification of triglycerides with methanol using NaOH or KOH as liquid base catalyst. Catalysts as such are corrosive to the equipment, and as these catalysts are in liquid phase must be neutralized after the completion of the reaction, typically using HCl, thus producing salt streams. Moreover, due to the presence of free fatty acids it reacts to form soaps as unwanted by-products, hence requiring more expensive separation processes. Therefore, there is a great need on the development of industrial processes for biodiesel production using solid acid catalysts. The key benefit of using solid acid catalysts is that no polluting by-products are formed and the catalysts do not have to be removed since they do not mix with the biodiesel product.

Advances on the development of novel heterogeneous catalysts for transesterification of triglycerides in biodiesel

This paper describes experimental work done towards the search for more profitable and sustainable alternatives regarding biodiesel production, using heterogeneous catalysts instead of the conventional homogenous alkaline catalysts, such as NaOH, KOH or sodium methoxide, for the methanolysis reaction. This experimental work is a first stage on the development and optimization of new solid catalysts, able to produce biodiesel from vegetable oils. The heterogeneous catalytic process has many differences from the currently used in industry homogeneous process. The main advantage is that, it requires lower investment costs, since no need for separation steps of methanol/catalyst, biodiesel/catalyst and glycerine/catalyst. This work resulted in the selection of CaO and CaO modified with Li catalysts, which showed very good catalytic performances with high activity and stability. In fact FAME yields higher than 92% were observed in two consecutive reaction batches without expensive intermediate reactivation procedures. Therefore, those catalysts appear to be suitable for biodiesel production.