Corrosion protection of PVD and paint coatings for selective solar absorber surfaces

The selective solar absorber surface is a fundamental part of a solar thermal collector, as it is responsible for the solar radiation absorption and for reduction of radiation heat losses. The surface’s optical properties, the solar absorption (á) and the emittance (å), have great impact on the solar thermal collector efficiency. In this work, two coatings types were studied: coatings obtained by physical vapor deposition (PVDs) and coatings obtained by projection with different paints (PCs) on aluminum substrates. The most common industrial high performing solar selective absorbers are nowadays produced by vacuum deposition methods, showing some disadvantages, such as lower durability, lower resistance to corrosion, adhesion and scratch, higher cost and complex production techniques. Currently, spectrally selective paints are a potential alternative for absorbing surfaces in low temperature applications, with attractive features such as ease of processing, durability and commercial availability with low cost. Solar absorber surfaces were submitted to accelerated ageing tests, specified in ISO 22975-3. This standard is applicable to the evaluation of the long term behavior and service life of selective solar absorbers for solar collectors working under typical domestic hot water system conditions. The studied coatings have, in the case of PVDs solar absorptions between 0.93 and 0.96 and emittance between 0.07 and 0.10, and in the case of PCs, solar absorptions between 0.91 and 0.93 and emittance between 0.40 and 0.60. In addition to evaluating long term behavior based on artificial ageing tests, it is also important to know the degradation mechanism of different coatings that are currently in the market. Electrochemical impedance spectroscopy (EIS) allows for the assessment of mechanistic information concerning the degradation processes, providing quantitative data as output, which can easily relate to the kinetic parameters of the system. EIS measures were carried out on Gamry FAS2 Femostat coupled with a PCL4 Controller. Two electrolytes were used, 0.5 M NaCl and 0.5 M Na2SO4, and the surfaces were tested at different immersion times up to 4 weeks. The following types of specimens have been tested: Aluminium with/without surface treatment, 3 selective paint coatings (one with a poly(urethane) binder and two with silicone binders) and 2 PVD coatings. Based on the behaviour of the specimens throughout the 4 weeks of immersion, it is possible to conclude that the coating showing the best protective properties corresponds to the selective paint coating with a polyurethane resin followed by the other paint coatings, whereas both the PVD coatings do not confer any protection to the substrate, having a deleterious effect as compared to the untreated aluminium reference.

Design of advanced reverse osmosis and nanofiltration membranes for water purification

Most commercially available reverse osmosis (RO) and nanofiltration (NF) membranes are based on the thin film composite (TFC) aromatic polyamide membranes. However, they have several disadvantages including low resistance to fouling, low chemical and thermal stabilities and limited chlorine tolerance. To address these problems, advanced RO/NF membranes are being developed from polyimides for water and wastewater treatments. The following three projects have resulted from my research. (1) Positively charged and solvent resistant NF membranes. The use of solvent resistant membranes to facilitate small molecule separations has been a long standing industry goal of the chemical and pharmaceutical industries. We developed a solvent resistant membrane by chemically cross-linking of polyimide membrane using polyethylenimine. This membrane showed excellent stability in almost all organic solvents. In addition, this membrane was positively charged due to the amine groups remaining on the surface. As a result, high efficiency (> 95%) and selectivity for multivalent heavy metal removal was achieved. (2) Fouling resistant NF membranes. Antifouling membranes are highly desired for “all” applications because fouling will lead to higher energy demand, increase of cleaning and corresponding down time and reduced life-time of the membrane elements. For fouling prevention, we designed a new membrane system using a coating technique to modify membrane surface properties to avoid adsorption of foulants like humic acid. A layer of water-soluble polymer such as polyvinyl alcohol (PVA), polyacrylic acid (PAA), polyvinyl sulfate (PVS) or sulfonated poly(ether ether ketone) (SPEEK), was adsorbed onto the surface of a positively charged membrane. The resultant membranes have a smooth and almost neutrally charged surface which showed better fouling resistance than both the positively charged NF membranes and commercially available negatively charged NTR-7450 membrane. In addition, these membranes showed high efficiency for removal of multivalent ions (> 95% for both cations and anions). Therefore, these antifouling surfaces can be potentially used for water softening, water desalination and wastewater treatment in a membrane bioreactor (MBR) process. (3) Thermally stable RO membranes. Commercial RO membranes cannot be used at temperature higher than 45°C due to the use of polysulfone substrate, which often limits their applications in industries. We successfully developed polyimides as the membrane substrate for thermally stable RO membranes due to their high thermal resistance. The polyimide-based composite polyamide membranes showed desalination performance comparable to the commercial TFC membrane. However, the key advantage of the polyimide-based membrane is its high thermal stability. As the feed temperature increased from 25oC to 95oC, the water flux increased 5 - 6 times while the salt rejection almost kept constant. This membrane appears to provide a unique solution for hot water desalination and also a feasible way to improve the water productivity by increasing the operating temperature without any drop in salt rejection.

Los óleos alquídicos Griffin : Composición, propiedades y aplicación

Uno de los principales inconvenientes que tiene la pintura al óleo es su lento secado. Dicho esto, cabe preguntarse si existe algún tipo de pintura que tenga las cualidades de los óleos pero que sequen más rápido que estos. La respuesta, afirmativa, la encontramos en los óleos alquídicos, que en nuestro país únicamente se comercializan bajo la marca Griffin de Winsor & Newton. Se trata de unas pinturas relativamente recientes, poco conocidas por los pintores y muy poco estudiadas. Con el objetivo de paliar estas carencias, el presente artículo contiene las principales conclusiones de un trabajo en el que se ha estudiado la composición de las pinturas Griffin, sus principales características (viscosidad, brillo, flexibilidad, textura, opacidad, secado que es lo que más nos interesa, estabilidad etc.), su aplicación práctica mediante el arte pictórico (soportes, disolventes, reglas para pintar, correcciones, veladuras, barnizado, etc.) y su mezcla con otro tipo de procedimientos pictóricos como el óleo, el acrílico, la cera encáustica y diversos temples (huevo, cola y caseína).

Lead (pb) toxicity in saccharomyces cerevisiae: the role of cell wall

O chumbo é utilizado em muitos produtos, tais como baterias, gasolina, tintas e corantes, resultando na sua libertação no meio ambiente. Neste trabalho, foi examinado o papel da parede celular da levedura Saccharomyces cerevisiae como uma barreira ou como alvo da toxicidade do chumbo. A biodisponibilidade do Pb é muito reduzida pelos componentes do meio de cultura YEPD, o que dificulta a avaliação da toxicidade deste elemento em concentrações ambientalmente realistas. Para avaliar a toxicidade de Pb em S. cerevisiae, em condições de crescimento, foram efetuadas diferentes diluições (10-100 vezes) do meio YEPD, as quais foram misturadas com várias concentrações de Pb (0,1-1,0 mmol/l). Observou-se que o YEPD diluído 25 vezes constituía a melhor condição de compromisso entre o crescimento celular e a precipitação de Pb. Os genes CWP1 e CWP2 codificam para duas grandes manoproteínas da parede celular da levedura S. cerevisiae; a deleção destes genes CWP aumenta a permeabilidade da parede celular. A suscetibilidade de células de levedura interrompidas no gene CWP1 (estirpe cwp1Δ) ou CWP2 (estirpe cwp2Δ) foi comparada com a da estirpe, isogénica, selvagem (WT). Verificou-se que o crescimento das estirpes cwp1Δ e cwp2Δ, no meio de cultura YEPD 25 vezes diluído, na presença de Pb, não diferiu do crescimento da estirpe WT. Este resultado sugere que a alteração da permeabilidade da parede celular não altera a sensibilidade de células de levedura ao Pb. Foi investigada o impacto do Pb na parede celular de levedura. Para este efeito, comparou-se a suscetibilidade ao dodecil sulfato de sódio (SDS), ao calcofluor (CFW) e a uma enzima que degrada a parede da célula (liticase), em células da estirpe WT não expostas ou expostas a Pb durante 4, 8 ou 24 h. Além disso, o conteúdo de quitina da parede celular de levedura foi investigada por coloração das células com CFW. Os resultados não mostraram uma alteração da suscetibilidade ao SDS e ao CFW, nas células tratadas com Pb; contudo, nas células tratadas durante 24 h com Pb, observou-se um aumento da sensibilidade à liticase e um aumento da coloração com CFW. Estes resultados sugerem que o chumbo interage com a parede celular da levedura e influencia a sua composição. Deve ser levado a cabo trabalho adicional a fim de confirmar estes resultados.

Cyto- and Genotoxicity assessment of manufactured nano cerium dioxide in the A549 cell line

In the past decades the growing application of nanomaterials (NMs) in diverse consumer products has raised various concerns in the field of toxicology. They have been extensively used in a broad range of applications and cover most of the industrial sectors as well as the medicine and the environmental areas. The most common scenarios for human exposure to NMs are occupational, environmental and as consumers and inhalation is the most frequent route of exposure, especially in occupational settings. Cerium dioxide NMs (nano-CeO2) are widely used in a number of applications such as in cosmetics, outdoor paints, wood care products as well as fuel catalysts. For such reason, nano-CeO2 is one of the selected NMs for priority testing within the sponsorship program of the Working Party of Manufactured Nanomaterials of the OECD. In this context, the aim of this study is to assess the safety of nano-CeO2 (NM-212, Joint Research Center Repository) through the characterization of its cytotoxicity and genotoxicity in a human alveolar epithelial cell line. A dispersion of the NM in water plus 0.05% BSA was prepared and sonicated during 16 minutes, according to a standardized protocol. DLS analysis was used to characterize the quality of the NM dispersion in the culture medium. To evaluate the cytotoxicity of nano-CeO2 in the A549 cell line, the colorimetric MTT assay was performed; the capacity of cells to proliferate when exposed to CeO2 was also assessed with the Clonogenic assay. The genotoxicity of this NM was evaluated by the Comet Assay (3 and 24h of exposure) to quantify DNA breaks and the FPG-modified comet assay to assess oxidative DNA damage. The Cytokinesis-Block Micronucleus (CBMN) assay was used to further detect chromosome breaks or loss. The nano-CeO2 particles are spherical, displaying a diameter of 33 nm and 28 m2/g of surface area. The results of the MTT assay did not show any decreased in cells viability following treatment with a dose-range of nano-CeO2 during 24h. Nevertheless, the highest concentrations of this NM were able to significantly reduce the colony forming ability of A549 cells, suggesting that a prolonged exposure may be cytotoxic to these cells. Data from both genotoxicity assays revealed that nano-CeO2 was neither able to induce DNA breaks nor oxidative DNA damage. Likewise, no significant micronucleus induction was observed. Taken together, the present results indicate that this nano-CeO2 is not genotoxic in this alveolar cell line under the tested conditions, although further studies should be performed, e.g., gene mutation in somatic cells and in vivo chromosome damage (rodent micronucleus assay) to ensure its safety to human health.

AIR SIDE HEAT TRANSFER ENHANCEMENT IN HEAT EXCHANGERS UTILIZING INNOVATIVE DESIGNS AND THE ADDITIVE MANUFACTURING TECHNIQUE

Over the last decade, rapid development of additive manufacturing techniques has allowed the fabrication of innovative and complex designs. One field that can benefit from such technology is heat exchanger fabrication, as heat exchanger design has become more and more complex due to the demand for higher performance particularly on the air side of the heat exchanger. By employing the additive manufacturing, a heat exchanger design was successfully realized, which otherwise would have been very difficult to fabricate using conventional fabrication technologies. In this dissertation, additive manufacturing technique was implemented to fabricate an advanced design which focused on a combination of heat transfer surface and fluid distribution system. Although the application selected in this dissertation is focused on power plant dry cooling applications, the results of this study can directly and indirectly benefit other sectors as well, as the air-side is often the limiting side for in liquid or single phase cooling applications. Two heat exchanger designs were studied. One was an advanced metallic heat exchanger based on manifold-microchannel technology and the other was a polymer heat exchanger based on utilization of prime surface technology. Polymer heat exchangers offer several advantages over metals such as antifouling, anticorrosion, lightweight and often less expensive than comparable metallic heat exchangers. A numerical modeling and optimization were performed to calculate a design that yield an optimum performance. The optimization results show that significant performance enhancement is noted compared to the conventional heat exchangers like wavy fins and plain plate fins. Thereafter, both heat exchangers were scaled down and fabricated using additive manufacturing and experimentally tested. The manifold-micro channel design demonstrated that despite some fabrication inaccuracies, compared to a conventional wavy-fin surface, 15% - 50% increase in heat transfer coefficient was possible for the same pressure drop value. In addition, if the fabrication inaccuracy can be eliminated, an even larger performance enhancement is predicted. Since metal based additive manufacturing is still in the developmental stage, it is anticipated that with further refinement of the manufacturing process in future designs, the fabrication accuracy can be improved. For the polymer heat exchanger, by fabricating a very thin wall heat exchanger (150μm), the wall thermal resistance, which usually becomes the limiting side for polymer heat exchanger, was calculated to account for only up to 3% of the total thermal resistance. A comparison of air-side heat transfer coefficient of the polymer heat exchanger with some of the commercially available plain plate fin surface heat exchangers show that polymer heat exchanger performance is equal or superior to plain plate fin surfaces. This shows the promising potential for polymer heat exchangers to compete with conventional metallic heat exchangers when an additive manufacturing-enabled fabrication is utilized. Major contributions of this study are as follows: (1) For the first time demonstrated the potential of additive manufacturing in metal printing of heat exchangers that benefit from a sophisticated design to yield a performance substantially above the respective conventional systems. Such heat exchangers cannot be fabricated with the conventional fabrication techniques. (2) For the first time demonstrated the potential of additive manufacturing to produce polymer heat exchangers that by design minimize the role of thermal conductivity and deliver a thermal performance equal or better that their respective metallic heat exchangers. In addition of other advantages of polymer over metal like antifouling, anticorrosion, and lightweight. Details of the work are documented in respective chapters of this thesis.

L'étain et les organoétains en milieu marin. Biogéochimie et écotoxicologie.

This report synthesizes the knowledge on the biogeochemical cycle, bioconcentration processes and ecotoxicity of tin and organotins in the marine environment. Concentrations levels, biomethylation mechanisms and exchanges between sediments and water are assessed. Emphasis is given on tributyltin sublethal effects, toxicity mechanisms and no effect levels for the most sensitive organisms. Regulations on the use of organotins as antifoulants in paints are examined. Conclusions and recommendations for environmental management and research are given.

Spectral damage model for lighted museum paintings: Oil, acrylic and gouache

A spectral aging test was developed to estimate the photochemical damage of oil, acrylic and gouache paints exposed to permanent lighting. The paints were irradiated at seven different wavelengths in the optical range to control and evaluate their spectral behaviour. To reach this objective, boxes with isolated aging cells were made. In each of box, one LED of a different wavelength and one photodiode were installed. Inside the boxes, the temperature of an exhibit area was recreated through a thermocouple sensor that controlled the temperature using a fan. The heat produced by the LED was dissipated by a thermal radiator. Moreover, to evaluate the exposure time dependence of the irradiation level, the test was performed using two different irradiation levels in ten exposure series. After each series, the spectral reflectance was measured, and the data collected for each paint and wavelength were used to develop a model of damage produced by the interaction between the spectral radiant exposure and the paint.

Hibridación in situ fluorescente (FISH)

Background: At the end of 80s, cloning technologies with the increase of the antibodies’ sensibility made easier the development of technologies based on Fluorescence in situ Hibridation (FISH). Nowadays, It’s widely used in the field of basic investigation as much as clinic diagnostic. Method: FISH is a technique that combines molecular biology with histochemistry way to detect specific nucleotide sequences so that chromosome’s section or even whole chromosome can be marked on metaphases cells (cell in division) and on attached cellular nucleus. This detection is realized using DNA fluorescence probes (marked with fluorophores), that can be different according to the structures manage to detect: large single-locus probes, small unique-sequence probes, chromosome- or region-specific “paints” or repetitive sequence probes and genomic DNA probes. Some of the applications of this technique is that can be so useful in the detection of numerical and structural chromosomal alterations such as polyploidies or genomic rearrangement, to mapping metaphases cells and even to detect bacteria or another type of microorganism. In addition, FISH allows us to monitoring diseases (antitumor therapies, quantification of genomic altered cells…) and the precise location of chromosomic broken spots on tumor searching for new genes involved in cancer and detect and map interested known genes. Conclusion: FISH has many advantages ahead of conventional cytogenetic techniques (bands G karyotype) overall at the time of establish a clinic diagnostic to detect tumors and chromosomic aberration, presenting a higher sensibility and specificity as well as being a relative quick technique (24 hours).

Revêtement intelligent à base des silices mésoporeuses fonctionnalisées pour le relargage stimulé d’agents antimicrobiens

Les biofilms bactériens sont composés d’organismes unicellulaires vivants au sein d’une matrice protectrice, formée de macromolécules naturelles. Des biofilms non désirés peuvent avoir un certain nombre de conséquences néfastes, par exemple la diminution du transfert de chaleur dans les échangeurs de chaleurs, l’obstruction de membranes poreuses, la contamination des surfaces coques de navires, etc. Par ailleurs, les bactéries pathogènes qui prolifèrent dans un biofilm posent également un danger pour la santé s’ils croissent sur des surfaces médicales synthétiques comme des implants biomédicaux, cathéters ou des lentilles de vue. De plus, la croissance sur le tissu naturel par certaines souches des bactéries peut être fatale, comme Pseudomonas aeruginosa dans les poumons. Cependant, la présence de biofilms reste difficile à traiter, car les bactéries sont protégées par une matrice extracellulaire. Pour tenter de remédier à ces problèmes, nous proposons de développer une surface antisalissure (antifouling) qui libère sur demande des agents antimicrobiens. La proximité et la disposition du système de relargage placé sous le biofilm, assureront une utilisation plus efficace des molécules antimicrobiennes et minimiseront les effets secondaires de ces dernières. Pour ce faire, nous envisageons l’utilisation d’une couche de particules de silice mésoporeuses comme agents de livraison d’agents antimicrobiens. Les nanoparticules de silice mésoporeuses (MSNs) ont démontré un fort potentiel pour la livraison ciblée d’agents thérapeutiques et bioactifs. Leur utilisation en nano médecine découle de leurs propriétés de porosité intéressantes, de la taille et de la forme ajustable de ces particules, de la chimie de leur surface et leur biocompatibilité. Ces propriétés offrent une flexibilité pour diverses applications. De plus, il est possible de les charger avec différentes molécules ou biomolécules (de tailles variées, allant de l’ibuprofène à l’ARN) et d’exercer un contrôle précis des paramètres d’adsorption et des cinétiques de relargage (désorption). Mots Clés : biofilms, nanoparticules de silice mésoporeuses, microfluidique, surface antisalissure.

Novel bio-based amine curing agents for epoxy resins: the way towards fully bio-based composite materials

Epoxy resins are widely used in many applications, such as paints, adhesives and matrices for composites materials, since they present the possibility to be easily and conveniently tailored in order to display a unique combination of characteristics. In literature, various examples of bio-based epoxy resins produced from a wide range of renewable sources can be found. Nevertheless, the toxicity and safety of curing agents have not been deeply investigated and it was observed that all of them still present some environmental drawback. Therefore, the development of new environmentally friendly fully bio-based epoxy systems is of great importance for designing green and sustainable materials. In this context, the present project aims at further exploring the possibility of using bio-based compounds as curing agents for epoxy resin precursors. A preliminary evaluation of several amine-based compounds demonstrated the feasibility of using Adenine as epoxy resin hardener. In order to better understand the crosslinking mechanism, the reaction of Adenine with the mono-epoxy compound Glycidyl 2-methylphenyl ether (G2MPE), was study by 1H-NMR analysis. Then Adenine was investigated as hardener of Diglycidil ether of bisphenol A (DGEBA), which is the simplest epoxy resin based on bisphenol A, in order to determine the best hardener/resin stoichiometric ratio, and evaluate the crosslinking kinetics and conversion and the final mechanical properties of the cured resin. Then, Adenine was tested as hardener of commercial epoxy resins, in particular the infusion resin Elan-tron® EC 157 (Elantas), the impregnation resin EPON™ Resin 828 (Hexion) and the bio-based resin SUPER SAP® CLR (Entropyresins). Such systems were used for the production of composites materials reinforced with chopped recycled carbon fibers and natural fibers (flax and jute). The thermo-mechanical properties of these materials have been studied in comparison with those ones of composites obtained with the same thermosetting resin reinforced with chopped virgin carbon fibers.

Towards a sustainable approach for Cultural Heritage Conservation: developing micro-structured green materials and analytical protocols for their performance assessment

Cleaning is one of the most important and delicate procedures that are part of the restoration process. When developing new systems, it is fundamental to consider its selectivity towards the layer to-be-removed, non-invasiveness towards the one to-be-preserved, its sustainability and non-toxicity. Besides assessing its efficacy, it is important to understand its mechanism by analytical protocols that strike a balance between cost, practicality, and reliable interpretation of results. In this thesis, the development of cleaning systems based on the coupling of electrospun fabrics (ES) and greener organic solvents is proposed. Electrospinning is a versatile technique that allows the production of micro/nanostructured non-woven mats, which have already been used as absorbents in various scientific fields, but to date, not in the restoration field. The systems produced proved to be effective for the removal of dammar varnish from paintings, where the ES not only act as solvent-binding agents but also as adsorbents towards the partially solubilised varnish due to capillary rise, thus enabling a one-step procedure. They have also been successfully applied for the removal of spray varnish from marble substrates and wall paintings. Due to the materials' complexity, the procedure had to be adapted case-by-case and mechanical action was still necessary. According to the spinning solution, three types of ES mats have been produced: polyamide 6,6, pullulan and pullulan with melanin nanoparticles. The latter, under irradiation, allows for a localised temperature increase accelerating and facilitating the removal of less soluble layers (e.g. reticulated alkyd-based paints). All the systems produced, and the mock-ups used were extensively characterised using multi-analytical protocols. Finally, a monitoring protocol and image treatment based on photoluminescence macro-imaging is proposed. This set-up allowed the study of the removal mechanism of dammar varnish and semi-quantify its residues. These initial results form the basis for optimising the acquisition set-up and data processing.

Formulazione e caratterizzazione di idropitture con materie prime “Bio-Based”

The market for paint products with raw materials derived from renewable sources is growing rapidly in the building industry. When high performance in wet scrub resistance is required, “washable” paints are used. However, formulating products with Bio-Based raw materials generally results in a decrease in performances compared to similar products with raw materials from fossil sources. Therefore, a new formulation approach is needed to characterize polymeric binders from renewable sources and to consider the synergistic effects given by blends of polymeric binders of different origin and chemical structure. To date, the development of new formulations that imply less environmental impact is necessary if these products have to remain competitive in the marketplace. During the trainingship in IVAS S.p.A., washable paints with different PVC (Pigment Volume Concentration) were formulated and tested, evaluating whether the performance of paints with polymeric binders obtained from renewable sources was comparable to those with polymeric binders from fossil sources. The binders were chemically characterized by DSC, FT-IR and NMR analysis. Characterization tests of paints were focused on the evaluation of degree of whiteness, hiding power, dirt setting, and wet scrub resistance. Following the results obtained from the available binder combinations, it was possible to formulate two washable paints with comparable performances to those from fossil sources: paint A with 20 % of alkydic polymer and 80 % styrene/acrylic polymer and paint B with 40 % of alkydic polymer and 60 % styrene/acrylic polymer. Finally, the formulation was completed by adding the mainly Bio-Based derived additives generally used for this category of paints.