Comparison between weight loss of bends in a pneumatic conveyor and erosion rate obtained in a centrifugal erosion tester for the same materials

In order to find a link between results obtained from a laboratory erosion tester and tests carried out on a pneumatic conveyor, a comparison has been made between weight loss from bends on an industrial-scale pneumatic conveyor and erosion rates obtained in a small centrifugal erosion tester, for the same materials. Identical test conditions have been applied to both experiments so that comparable test results have been obtained. The erosion rate of mild steel commonly used as the wall material of conveyor pipes and pipe bends was determined individually on both test rigs. A relationship between weight loss from the bends and erosion rate determined from the tester has been developed. A discussion based on the results and their applicability to the prediction of wear in pneumatic conveyors concludes the paper. © 2004 Elsevier B.V. All rights reserved.

The Stability of a Vertical Single-Walled Carbon Nanotube Under Its Own Weight

It has been reported recently that single carbon nanotubes were attached to AFM tips to act as nanotweezers. In order to investigate its stability, a vertical single-walled carbon nanotube (SWCNT) under its own weight is studied in this paper. The lower end of the carbon nanotube is clamped. Firstly the governing dimensionless numbers are derived by dimensional analysis. Then the theoretical analysis based on an elastic column model is carried out. Two ratios, I.e., the ratio of half wall thickness to radius (t=R) and the ratio of gravity to elastic resilience ($\rho$gR=E), and their influences on the ratio of critical length to radius are discussed. It is found that the relationship between the critical ratio of altitude to radius and ratio of half thickness to radius is approximately linear. As the dimensionless number $\rho$gR=E increases, the compressive force per unit length (weight) becomes larger, thus critical ratio of altitude to radius must become smaller to maintain stability. At last the critical length of SWCNT is calculated. The results of this paper will be helpful for the stability design of nanotweezers-like nanostructures.

Semi-weight function method on computation of stress intensity factors in dissimilar materials

Semi-weight function method is developed to solve the plane problem of two bonded dissimilar materials containing a crack along the bond. From equilibrium equation, stress and strain relationship, conditions of continuity across interface and free crack surface, the stress and displacement fields were obtained. The eigenvalue of these fields is lambda. Semi-weight functions were obtained as virtual displacement and stress fields with eigenvalue-lambda. Integral expression of fracture parameters, K-I and K-II, were obtained from reciprocal work theorem with semi-weight functions and approximate displacement and stress values on any integral path around crack tip. The calculation results of applications show that the semi-weight function method is a simple, convenient and high precision calculation method.

Experimental study on the microstructure and nanomechanical properties of the wing membrane of dragonfly

Detailed investigations on the microstructure and the mechanical properties of the wing membrane of the dragonfly are carried out. It is found that in the direction of the thickness the membrane was divided into three layers rather than a single entity as traditionally considered, and on the surfaces the membrane displays a random distribution rough microstructure that is composed of numerous nanometer scale columns coated by the cuticle wax secreted. The characteristics of the surface structure are measured and described. The mechanical properties of the membranes taken separately from the wings of live and dead dragonflies are investigated by the nanoindentation technique. The Young's moduli obtained here are approximately two times greater than the previous result, and the reasons that yield the difference are discussed.

Microstructure and nanomechanical properties of the wing membrane of dragonfly

Detailed investigations on the microstructure and the mechanical properties of the wing membrane of the dragonfly were carried out. It was found that in the direction of the thickness the membrane was divided into three layers rather than as traditionally considered as a single entity, and on the surfaces the membrane displayed a random distribution rough microstructure that was composed of numerous nanometer scale columns coated by the cuticle wax secreted. The characteristics of the surfaces were accurately measured and a statistical radial distribution function of the columns was presented to describe the structural properties of the surfaces. Based on the surface microstructure, the mechanical properties of the membranes taken separately from the wings of living and dead dragonflies were investigated by the nanoindentation technique. The Young's moduli obtained here are approximately two times greater than the previous result, and the reasons that yield the difference are discussed. (C) 2007 Elsevier B.V. All rights reserved.

A Study of the Tribological Behavior of Carbon-Nanotube-Reinforced Ultrahigh Molecular Weight Polyethylene Composites

The tribological properties of the high-strength and high-modulus ultrahigh molecular weight polyethylene (UHMWPE) film and the UHMWPE composites reinforced by multiwalled carbon nanotubes (MWCNT/UHMWPE) were investigated using a nanoindenter and atomic force microscope (AFM). The MWCNT/UHMWPE composites films exhibited not only high wear resistance but also a low friction coefficient compared to the pure UHMWPE films. We attribute the high wear resistance to the formation of the new microstructure in the composites due to the addition of MWCNTs.

Seasonal foods, gonadal maturation, and length-weight relationships for nine fishes commonly captured by shrimp trawl on the Northwest Gulf of Mexico Continental Shelf

Recent emphasis on ecosystem approaches to fisheries management renews interest in, and the need for, trophic information about fish communities. A program was started in 1980 at the National Marine Fisheries Service Galveston Laboratory to develop a trophic database for continental shelf fishes. Collections were made during 1982-1983 that were processed but never published, yet the data remain valid today for historical purposes and for delimiting food web components within ecosystem assessments. I examined spring, summer, and fall foods in offshore populations of nine common species of trawl-susceptible fishes, with particular reference to predation on commercial penaeid shrimps (Farfantepenaeus and Litopenaeus). Diets were evaluated with the Index of Relative Importance (IRI) which combines the occurrence, number, and weight of each food item. Bank sea bass (Centropristis ocyurus) and bighead searobin (Prionotus tribulus) primarily consumed crabs, more so by larger than smaller fish. Inshore lizardfish (Synodus foetens) was almost entirely piscivorous. Ocellated flounder (Ancylopsetta ommata) consumed fishes, crabs, and stomatopods. Dwarf sand perch (Diplectrum bivittatum), blackwing searobin (Prionotus rubio), rock sea bass (Centropristis philadelphica), southern kingfish (Menticirrhus americanus), and red snapper (Lutjanus campechanus) fed mainly on shrimps. Most fish diets varied with respect to size (age), time of day, area sampled, depth, or season. Rimapenaeus and Sicyonia were the most frequently identified shrimp genera - only five Farfantepenaeus and no Litopenaeus were identified in almost 4,300 fish stomachs. I also examined gonadal development and documented fish length-weight relationships. Ripe gonads were most frequently found during summer in dwarf sand perch, during fall in ocellated flounder and bighead searobin, and during spring for other species, except no ripe red snapper or bank sea bass were collected. Rock sea bass was found to be a protogynous hermaphrodite, while dwarf sand perch is a synchronous hermaphrodite. Only ocellated flounder and southern kingfish exhibited sex-related differences in length-weight relationships. (PDF contains 40 pages.)