Influência de pontas de pulverização e adjuvantes no potencial de redução de deriva em túnel de vento

The drift is intimately linked to inappropriate use of pesticides and an important factor for reducing it, is the correct selection of spray nozzles and adjuvants. The objective of this work was to evaluate the drift potential in wind tunnel with different spray nozzles and different concentrations of adjuvants. The experiment was composed by six spray solutions (vegetable oil (in three concentrations), mineral oil, surfactant and reducing drift), which were applied with two nozzles, one pre-orifice flat fan (DG 8003 VS) and other with air induction (AI 8003 VS), totaling 12 treatments, with three repetitions. The equipment used was a wind tunnel, where the drift collections were made at different points. The treatments averages were compared using Confidence Interval at 5% probability. The analysis of the percentage of drift showed that the treatments had different behaviors. The nonylphenol ethoxylate adjuvant presented the highest drift when applied with the nozzle of pre-orifice and the lowest drift when applied with the air induction. The behavior of these nozzles when the oil-based adjuvant was used showed apposite results to those obtained for the surfactant. For the DG nozzles the lowest percentage of drift, at all analyzed distances, was observed to the treatment with vegetable oil (1.0%) and with the AI nozzles the lower drift was found for the treatment with nonylphenol ethoxylate (0.0625%), for the four distances in the collection. The result showed that both the spray nozzles and adjuvants alter directly the drift potential. There was no proportionately between the concentration of the oil-based adjuvant and the drift percentage.

Software de rastreamento de embarcações e plataforma eletrônica para ensaios hidrodinâmicos em túnel de vento

Pós-graduação em Engenharia Elétrica - FEIS

Potencial de redução da deriva em função de adjuvantes e pontas de pulverização

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo teórico e experimental das curvas características de um ventilador axial aplicado em pulverização agrícola

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise numérica e experimental na determinação da potência térmica dissipada em componentes eletrônicos

Pós-graduação em Engenharia Mecânica - FEIS

Pontas e adjuvantes no potencial risco de deriva em pulverizações de produtos fitossanitários

Pós-graduação em Agronomia (Proteção de Plantas) - FCA

Avaliação de medidores com múltiplas tomadas de pressão na macromedição em sistemas de água

Pós-graduação em Engenharia Civil - FEIS

Determinação da deriva da mistura 2,4-D e glyphosate com diferentes pontas de pulverização e adjuvantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Construção e validação de um túnel de vento para ensaios de estimativa da deriva em pulverizações agrícolas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Modelo dinâmico de um túnel de vento de sopro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A laboratory evaluation of alcohols as attractants for the sandfly Lutzomyia longipalpis (Diptera: Psychodidae)

Background: The potential attraction from 1-octen-3-ol for sandflies has been documented; however, studies using other primary alcohols are limited.Findings: We used a wind tunnel to compare the activation and attractive behaviors in male and female Lutzomyia longipalpis using 1-octen-3-ol and three additional alcohols, 1-octanol, 1-heptanol and 1-nonanol at three different concentrations: neat (100%) and diluted in hexane (10% and 50%). The compounds 1-octen-3-ol and 1-nonanol induced a clear concentration-dependent activation and attraction response in females. In males, 1-octen-3-ol, 1-nonanol and 1-heptanol yielded the same results.Conclusions: L. longipalpis is attracted to 1-octen-3-ol, 1-nonanol and 1-heptanol, which are found in many plant volatiles.

Theoretical and experimental study of agricultural spraying using CFD

This paper presents a computational fluid dynamics (CFD) application about the axial fan design used in an agricultural spraying system with a theoretical and experimental analysis of comparative results between the characteristic curves of a fan for several rotations and numerical results for the influence of blade attack angle variation and optimization of the spraying system, both for a same rotation. Flow was considered three-dimensional, turbulent, isothermal, viscous and non-compressible in a steady state, disregarding any influence of the gravity field. The average turbulent field was obtained from the application of time average where the turbulence model required for closing the set of equations was the k-E model. Resolution of all connected phenomena was achieved with the help of a fluid dynamics computer, CFX, which uses the finite volumes technique as a numerical method. In order to validate the theoretical analysis, an experiment was conducted in a circular section of a horizontal wind tunnel, using a Pitot tube for pressure readings. The main results demonstrate that the methodology used, based on CFD techniques, is able to reproduce the phenomenological behavior of an axial fan in a spraying system because results were very reliable and similar to experimentally measured ones.

Projeto mecânico de um modelo para túnel de vento e validação de seus componentes à partir de simulações em software de elementos finitos

The objective of this study was to develop a model that allows testing in the wind tunnel at high angles of attack and validates its most critical components by analyzing the results of simulations in finite element software. During the project this structure suffered major loads identified during the flight conditions and, from these, we calculated the stresses in critical regions defined as the parts of the model that have higher failure probabilities. All aspects associated with Load methods, mesh refining and stress analysis were taken into account in this approach. The selection of the analysis software was based on project needs, seeking greater ease of modeling and simulation. We opted for the software ANSYS® since the entire project is being developed in CAD platforms enabling a friendly integration between software's modeling and analysis

Spray adjuvant characteristics affecting agricultural spraying drift

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Interação pontas-adjuvantes na estimativa do risco potencial de deriva de pulverizações

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)