946 resultados para Waste disposal
Resumo:
Diffusion coefficients and retardation factors of two metal cations (Cd2+ and Pb2+) were measured for a compacted Brazilian saprolitic soil derived from gneiss, aiming to assess its geoenvironmental performance as a liner for waste disposal sites. This soil occurs extensively all over the country in very thick layers, but has not been used in liners because of its hydraulic conductivity, higher than 10(-9) m/s when compacted at optimum water content of standard Proctor energy, but which can be reduced by means of appropriate compaction techniques or additives. Batch, column, and diffusion tests were carried out with monospecies synthetic solutions at pH 1, 3, and 5.5. Measured diffusion coefficients varied between 0.5 and 4 X 10(-10) m(2)/s. Retardation factors show that cadmium, a very mobile cation, is not adsorbed at pH I but is significantly retained at pH 3 and pH 5.5, whereas lead is retained at all tested pH values though slightly at pH 1. Estimated retardation factors from batch tests were 1.3-2.3 times those resulting from column tests and at its highest when obtained by diffusion tests; whereas batch tests allow a more complete exposure of the soil grains to the solution, time-dependent nonspecific adsorption may take longer to occur. The importance of contact time was observed and should be considered in further investigations. Its significant retention of metals suggests a promising utilization of this soil as a bottom liner for wastes landfills.
Resumo:
o presente trabalho é um estudo exploratório a respeito da síntese de filmes de diamante via deposiçãoquímica a vapor (CVD) sobre alguns substratos cerâmicos: diboreto de titânio (TiB2), ítria (Y20a), zircão (ZrSi04), zircônia parcialmente e totalmente estabilizada com ítria (Zr02), pirofilita ( Al2Si4OlO(OHh), .alumina (Al2Oa) e nitreto de boro hexagonal (h-BN). Estes substratos foram produzidos, em sua maioria, a partir da sinterização de pós micrométricos em altas temperaturas. Além do estudo em relação a possíveis candidatos alternativos ao tradicional silício para o crescimento de filmes auto-sustentáveis, procuramos encontrar substratos onde o filme aderisse bem e cujas propriedades tribológicas pudessem ser melhoradas com o recobrimento com filme de diamante.Dentre os materiais selecionados, constatamos que a topografia da superfície relacionada à densidade de contornos de grão, desempenha um papel relevante na nucleação do diamante. Além disso, os materiais que favorecem a formação de carbonetos conduziram a melhores resultados na nucleação e crescimento do filme, indicando que a ação da atmosfera reativa do CVD com o substrato também contribui decisivamente para o processo de nucleação. A partir dos resultados obtidos, concluímos que a aderência do filme de diamante ao zircão é excelente, assim como a qualidade do filme, o que pode serexplorado convenientemente caso as propriedades mecânicas do sinterizado de zircão sejam adequadas. No caso da zircônia parcialmente estabilizada, os resultados obtidos foram surpreendentes e este material poderia substituir o convencional substrato de silício para a deposição de filmes auto-sustentados de diamante, com inúmeras vantagens, dentre elas o fato de ser reutilizável e de não ser necessário ataque com ácidos para remoção do substrato, o que evita a geração de resíduos químicos.
Resumo:
Trata-se nesta dissertação do emprego da reciclagem a frio de revestimentos asfálticos em usina com a finalidade de aproveitamento como camada de revestimento em vias de tráfego leve e muito leve. São revistos os conceitos de dimensionamento de pavimentos e da dosagem de misturas asfálticas. Dá-se especial atenção ao valor do revestimento asfáltico recuperado e a relevância que a reciclagem tem sobre a redução do descarte de resíduos sólidos no meio ambiente. Identifica-se a importância do emprego da reciclagem sobre o comportamento da sociedade. A metodologia adotada tem por base uma revisão bibliográfica dos registros de trabalhos de reciclagem a frio realizados no Brasil e no exterior. Faz-se um relato dos procedimentos de caracterização dos materiais envolvidos e dos cuidados a serem observados para obter-se um produto final de qualidade. Estão aqui descritos os processos industriais de usinagem da mistura reciclada em plantas industriais fixas. É estabelecida uma proposta de definição da viabilidade econômica de emprego da reciclagem a frio em comparação com o revestimento asfáltico tradicional. Ao final são registrados temas a serem estudados visando tornar a reciclagem a frio de revestimentos asfálticos em usinas de áreas urbanas mais conhecida e considerada como alternativa para a melhoria da qualidade de vida nas cidades.
Resumo:
Brazil has vast amounts of hydric resources, whose quality has been deteriorating due to pollutant dumping. Household waste disposal is one of the main sources of water pollution, stimulating bacteria proliferation and introducing microorganisms, including those from fecal matter. Conventional water disinfection methods are a solution, but on the downside, they lead to the formation byproducts hazardous to human health. In this study, aiming to develop bactericidal filters for the disinfection of drinking water; silver nanoparticles were deposited on alumina foams through three routes: sputtering DC, dip coating and in situ chemical reduction of silver nitrate. The depositions were characterized through X-ray diffraction, scanning electron microscopy and EDS element mapping. The influence of the depositions on permeability and mechanical properties of the ceramic foams was assessed and, in sequence, a preliminary antibacterial efficiency analysis was carried out. Characterization results indicate that the chemical reduction routes were efficient in depositing homogeneously distributed silver particles and that the concentration of the metallic precursor salt affects size and morphology of the particles. The antibacterial efficiency analysis indicates that the chemical reduction filters have potential for water disinfection
Resumo:
This work aims to present the diagnosis and the evaluation of areas of final destination of urban solid waste in Rio Grande do Norte (RN) state. The survey was based on the experience of the State of São Paulo, which made its first inventory in 1997, through its Companhia de Tecnologia de Saneamento Ambiental CETESB. The methodology for the structuring of diagnosis was the Índice de Qualidade de Aterros de Resíduo -- IQR, developed by the Institute for Technological Research of São Paulo (ITRP). The calculation is based on the completion of a matrix that contains information about the main features of the site, infrastructure and operating conditions of the area of waste disposal. This study intends to subsidize the state government of Rio Grande do Norte through its State Secretariat of Environment and Water Resources and the Instituto de Desenvolvimento Sustentável e Meio Ambiente do RN (IDEMA), as well as federal, state and municipal authorities, in the definition of public policies for integrated management of municipal solid wastes to take account of environmental preservation and improvement of sanitary conditions of Natal-RN population.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
The panorama of Urban Solid Waste (USW) in Brazil, in general lacks information, given the immensity of the country. However, it is from available data that the public executives should define the USW management. To contribute to the choice of a model for the management of USW in small municipalities, this study reviews the related literature, showing an overview of the final disposal of USW in small municipalities. Several data and researches are discussed, concluding that the available data, despite being provided by the public managers, who often attenuate the problem, should be considered for the proposition of policies to encourage the waste treatment
Resumo:
The brazilian marginal basins have a huge potential to generate and accumulate petroleum. Incised valleys which are eroded in response to a fall of relative sea level are related to potential reservoir as well, modern drowned-valley estuaries serve as harbors to petroleum and salt industries, fisheries, waste-disposal sites and recreational areas for a significant fraction of the world s population. The combined influence of these factors has produced a dramatic increase in research on modern and ancient incised-valley systems. This research is one expression of this interest. The integrated use of satellites images and high resolution seismic (bathymetry, sides scan sonar) was used on the Apodi River mouth-RN to characterizes the continental shelf This area is located at the Potiguar Basin in the NE Brazilian Equatorial Atlantic margin. Through bathymetric and side scan sonar data processing, a digital Terrain Model was developed, and a detailed geomorphologic analysis was performed. In this way was possible to recognize the geomorphologic framework and differents sismofacies, which may influence this area. A channel extending from the ApodiMossoró river mouth to the shelf edge dominates the investigated area. This structure can be correlated with the former river valley developed during the late Pleistocene sea level fall. This channel has two main directions (NW-SE and NE-SW) probably controlled by the Potiguar Basin structures. The western margin of the channel is relatively steep and pronounced whereas the eastern margin consists only of a gentle slope. Longitudinal bedforms and massive ridges also occur. The first are formed doe to the shelf sediment rework and the reef-like structures probably are relics of submerged beachrock-lines indicating past shoreline positions during the deglacial sea-level rise. The sub-bottom seismic data allow the identification of different sismic patterns and a marcant discontinuity, interpreted as the Upper
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)
Resumo:
Este trabalho objetivou caracterizar um sistema de solos, evidenciando a propriedades que possam esclarecer sua dinâmica e contribuir para a definição de critérios que condicionem a aptidão destes solos como receptores de efluentes. Trata-se de uma área experimental de estudos, contígua à Estação de Tratamento de Esgoto do município de Lins (SP), onde o efluente é gerado a partir do tratamento de esgoto por sistema de lagoas de estabilização. Os solos, situados ao longo de uma vertente com ligeira inclinação, foram caracterizados por meio de análises, morfológica, granulométrica, química, mineralógica e micromorfológica, realizadas em amostras coletadas em cinco trincheiras em toposseqüência. Os solos são desenvolvidos a partir dos sedimentos arenosos da Formação Adamantina (Grupo Bauru) e constituem um sistema Latossolo - Argissolo onde a transição Bw - Bt ocorre lateralmente do topo para a base da vertente. Foram identificadas três fases pedogenéticas nesta associação de solos. A primeira, argiluviação e adensamento de partículas, responsável pela formação dos horizontes texturais, foi superposta pelos processos de latossolização e hidromorfismo, atuantes na dinâmica atual destes solos. Análises micromorfológicas mostraram tratar-se de solos com intensa porosidade, caracterizada pelo empilhamento dos grãos do esqueleto quartzoso amplamente predominante e pelo arranjo entre os microagregados granulares. A permeabilidade é ainda favorecida pela intensa ação da mesofauna. Os solos são distróficos e compostos por caulinita e óxidos de Fe na fração argilosa. Por constituírem um sistema frágil, a disposição de quaisquer tipos de resíduos nestes solos requer o monitoramento constante de suas propriedades, tanto para a manutenção, quanto para a recuperação da qualidade desta cobertura pedológica.
Resumo:
The effects of metal bioleaching on nutrient solubilization, especially nitrogen and phosphorous, from anaerobically-digested sewage sludge were investigated in this work. The assessment of the sanitary quality of the anaerobic sludge after bioleaching was also carried out by enumerating indicator (total coliforms, fecal coliforms, and fecal streptococci) and total heterotrophic bacteria. The experiments of bioleaching were performed using indigenous sulphur-oxidizing bacteria (Thiobacillus spp.) as inoculum and samples of anaerobically-digested sludge. Nitrogen and phosphorous solubilization from sewage sludge was assessed by measuring, respectively, the concentration of Total Kjeldahl Nitrogen, ammonia, nitrate/nitrite, and soluble and total phosphorous before and after the bioleaching assays. At the end of the experiment, after 4 days of incubation (final pH of 1.4), the following metal solubilization yields were obtained: zinc, 91%; nickel, 87%; copper, 79%; lead, 52%; and chromium, 42%. As a result of sludge acidification, the viable counts of selected indicator bacteria were decreased to below the detection limit (4 × 103 cfu 100 ml-1), followed by an increase in the mineral fraction of nitrogen (from 6 to 10%) and in the soluble fraction of phosphorous (from 15 to 30%). Although some loss of sludge nutrients can occur during solid-liquid separation following bioleaching, its beneficial effects as metal removal and reduction of pathogenic bacteria are sufficient to consider the potential of this treatment before sludge disposal onto agricultural fields.
Resumo:
Water samples (24 untreated water, 12 treated water and 24 served water) used in different stages of the slaughter process were examined to identify a possible source of pathogenic mycobacteria. The isolates were identified based on microscopy, morphological and biochemical features, mycolic acid analysis and molecular method - PCR-restriction-enzyme analysis. Eighteen mycobacterial strains were isolated from 60 water samples: 11 from untreated water, 5 from treated water and 2 from served water. All mycobacteria isolated were identified as Mycobacterium gordonae and showed the following PRA genotypes: III (27.8%), IV (38.9%) and V (33.3%).
Comportamento contrátil de barreiras selantes de solo estabilizado para base de lagoas de tratamento
Resumo:
Liners were proposed as subsoil contamination protection devices for waste disposal sites. In the rural environment, they can be used to construct pond bottoms for liquid waste treatment, but the construction needs to be quick and cheap. A good technical solution for these situations is the use of local soil compacted with low quantities of cement or lime, obtaining good properties for this purpose. These barriers need special care about their contraction behavior which may compromise its use. This work shows the results of contraction tests in sandy soil specimens and others stabilized with lime and with cement. Soil structure changes during cure time were checked using electronic scan microscopy. Results show maximum soil contraction of 0.648% for specimen with 14 days cure process. After twenty eight days of cure the contraction values were lower than 0.5%, which classifies the material as of low contraction. Electronic scan image shows significant material structure alteration up to seven days cure. Results show that studied mixtures had appropriate contraction behavior for liner usage.
Resumo:
The waters of Corumbataí River in the middle and eastern part of São Paulo State, Brazil, are extensively used for human consumption; their water quality has been modified mainly due to increasing pressure caused by population growth, accompanied by a more accentuated industrial development for the whole São Paulo State in the early 1970s. The Corumbataí River basin has, over time, received significant emissions of municipal waste products and discharges of wastewater, sludge, sewage, sanitary and industrial effluents, but the first effluent treatment plant at Rio Claro city was only inaugurated at the end of the 1990s. Data on river water quality from two widely spaced locations in the Corumbataí River basin are reported in this paper; they indicate the need for continuous initiatives and efforts by decision makers in order to improve and preserve the water quality in the basin for the 21st century. Copyright © 2007 IAHS Press.