Ambulatory assessment of 3D ground reaction force using plantar pressure distribution.

This study aimed to use the plantar pressure insole for estimating the three-dimensional ground reaction force (GRF) as well as the frictional torque (T(F)) during walking. Eleven subjects, six healthy and five patients with ankle disease participated in the study while wearing pressure insoles during several walking trials on a force-plate. The plantar pressure distribution was analyzed and 10 principal components of 24 regional pressure values with the stance time percentage (STP) were considered for GRF and T(F) estimation. Both linear and non-linear approximators were used for estimating the GRF and T(F) based on two learning strategies using intra-subject and inter-subjects data. The RMS error and the correlation coefficient between the approximators and the actual patterns obtained from force-plate were calculated. Our results showed better performance for non-linear approximation especially when the STP was considered as input. The least errors were observed for vertical force (4%) and anterior-posterior force (7.3%), while the medial-lateral force (11.3%) and frictional torque (14.7%) had higher errors. The result obtained for the patients showed higher error; nevertheless, when the data of the same patient were used for learning, the results were improved and in general slight differences with healthy subjects were observed. In conclusion, this study showed that ambulatory pressure insole with data normalization, an optimal choice of inputs and a well-trained nonlinear mapping function can estimate efficiently the three-dimensional ground reaction force and frictional torque in consecutive gait cycle without requiring a force-plate.

Creation and Validation of Chronojump-Boscosystem: A Free Tool to Measure Vertical Jumps

Measuring the height of the vertical jump is an indicator of the strength and power of the lower body. The technological tools available to measure the vertical jump are black boxes and are not open to third-party verification or adaptation. We propose the creation of a measurement system called Chronojump-Boscosystem, consisting of open hardware and free software. Methods: A microcontroller was created and validated using a square wave generator and an oscilloscope. Two types of contact platforms were developed using different materials. These platforms were validated by the minimum pressure required for activation at different points by a strain gauge, together with the on/off time of our platforms in respect of the Ergojump-Boscosystem platform by a sample of 8 subjects performing submaximal jumps with one foot on each platform. Agile methodologies were used to develop and validate the software. Results: All the tools fall under the free software / open hardware guidelines and are, in that sense, free. The microcontroller margin of error is 0.1%. The validity of the fiberglass platform is 0.95 (ICC). The management software contains nearly 113.000 lines of code and is available in 7 languages.

Vertical Delineation, 2014

Vertical delineators are intended to warn drivers of an approaching curve while providing them with a better appreciation of the sharpness of a curve. Drivers can then select an appropriate speed before entering the curve. Delineation can also provide continuous tracking information once drivers are within the curve to help position their vehicles within the travel lane while traversing the curve. The most common type of vertical delineation is post mounted delineators (PMDs). These devices are usually flexible or rigid posts with some amount of reflective surface mounted along the roadside to provide additional delineation. Another treatment that has been used is to provide additional delineation on chevron posts.

High-throughput and sensitive quantitation of plasma catecholamines by ultraperformance liquid chromatography-tandem mass spectrometry using a solid phase microwell extraction plate.

Plasma catecholamines provide a reliable biomarker of sympathetic activity. The low circulating concentrations of catecholamines and analytical interferences require tedious sample preparation and long chromatographic runs to ensure their accurate quantification by HPLC with electrochemical detection. Published or commercially available methods relying on solid phase extraction technology lack sensitivity or require derivatization of catecholamine by hazardous reagents prior to tandem mass spectrometry (MS) analysis. Here, we manufactured a novel 96-well microplate device specifically designed to extract plasma catecholamines prior to their quantification by a new and highly sensitive ultraperformance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method. Processing time, which included sample purification on activated aluminum oxide and elution, is less than 1 h per 96-well microplate. The UPLC-MS/MS analysis run time is 2.0 min per sample. This UPLC-MS/MS method does not require a derivatization step, reduces the turnaround time by 10-fold compared to conventional methods used for routine application, and allows catecholamine quantification in reduced plasma sample volumes (50-250 μL, e.g., from children and mice).

The birth of the Rheic Ocean - Early Palaeozoic subsidence patterns and subsequent tectonic plate scenarios

New plate-tectonic reconstructions of the Gondwana margin suggest that the location of Gondwana-derived terranes should not only be guided by the models, but should also consider the possible detrital input from some Asian blocks (Hunia), supposed to have been located along the Cambrian Gondwana margin, and accreted in the Silurian to the North-Chinese block. Consequently, the Gondwana margin has to be subdivided into a more western domain, where the future Avalonian blocks will be separated from Gondwana by the opening Rheic Ocean, whereas in its eastern continuation, hosting the future basement areas of Central Europe, different periods of crustal extension should be distinguished. Instead of applying a rather cylindrical model, it is supposed that crustal extension follows a much more complex pattern, where local back-arcs or intra-continental rifts are involved. Guided by the age data of magmatic rocks and the pattern of subsidence curves, the following extensional events can be distinguished: During the early to middle Cambrian, a back-arc setting guided the evolution at the Gondwana margin. Contemporaneous intra-continental rift basins developed at other places related to a general post-PanAfrican extensional phase affecting Africa Upper Cambrian formation of oceanic crust is manifested in the Chamrousse area, and may have lateral cryptic relics preserved in other places. This is regarded as the oceanisation of some marginal basins in a context of back-arc rifting. These basins were closed in a mid-Ordovician tectonic phase, related to the subduction of buoyant material (mid-ocean ridge?) Since the Early Ordovician, a new phase of extension is observed, accompanied by a large-scale volcanic activity, erosion of the rift shoulders generated detritus (Armorican Quartzite) and the rift basins collected detrital zircons from a wide hinterland. This phase heralded the opening of Palaeotethys, but it failed due to the Silurian collision (Eo-Variscan phase) of an intra-oceanic arc with the Gondwana margin. During this time period, at the eastern wing of the Gondwana margin begins the drift of the future Hunia microcontinents, through the opening of an eastern prolongation of the already existing Rheic Ocean. The passive margin of the remaining Gondwana was composed of the Galatian superterranes, constituents of the future Variscan basement areas. Remaining under the influence of crustal extension, they will start their drift to Laurussia since the earliest Devonian during the opening of the Palaeotethys Ocean. (C) 2008 Elsevier B.V. All rights reserved.

Models for vertical wood density of Scots pine, Norway spruce and birch stems, and their application to determine average wood density

Abstract

Pin guidance of reconstruction plate contour: an expanded role of external fixation

This article presents a modification of intraoperative external fixation for mandibular reconstruction with free tissue flaps. This technique is indicated when preregistration of the reconstruction plate is not possible due to transmandibular tumor extension. Once standard external fixation has been carried out and prior to segmental mandibulectomy, additional pins are fixed to the connecting rod that delineate the mandibular contour in three-dimensional (3D) space. Following mandibulectomy, these pins allow accurate contouring of the reconstruction plate and improved restoration of mandibular contour, projection, and dental occlusion. A step-by-step description of the technique using models and intraoperative photos is presented. This method of mandibular reconstruction is a simple and time-effective alternative to intraoperative computer navigation and 3D modeling in select cases of oral carcinoma where tumor infiltration of the outer mandibular cortex precludes prebending of the reconstruction plates.

Vertical Clearance Restrictions on Primary Roads and Primary Road Extensions: Standard U.S. Measurements [Vertical Clearance Log], May 1, 2015

The Vertical Clearance Log is prepared for the purpose of providing vertical clearance restrictions by route on the primary road system. This report is used by the Iowa Department of Transportation’s Motor Carrier Services to route oversize vehicles around structures with vertical restrictions too low for the cargo height. The source of the data is the Geographic Information Management System (GIMS) that is managed by the Office of Research & Analytics in the Performance & Technology Division. The data is collected by inspection crews and through the use of LiDAR technology to reflect changes to structures on the primary road system. This log is produced annually.

Dynamics and vertical distribution of a Hrabeiella periglandulata (Annelida) population in South Moravia, Czech Republic

The objective of this work was to evaluate the density, dynamics and vertical distribution of a Hrabeiella periglandulata population in a forest soil at Brno, Czech Republic. From December 2003 to November 2004, two plots covered by mixed stands and two covered by coniferous stands were sampled monthly. Six soil cores per plot were taken down to 15 cm and subdivided into layers, which were subjected to wet funnel extraction. Missing in one of the coniferous stands H. periglandulata was abundant in the mixed stand with the highest soil pH. In this stand, monthly sampling continued until November 2005, with three additional samplings up to January 2007. Mean annual density was 2,672±1,534 individuals m-2. Population dynamics differed from those reported from Germany. Highest densities were reached in early summer, lowest between August and December. Due to aggregated horizontal distribution, differences between monthly values were often nonsignificant. No significant correlation with climatic data was found. Nevertheless, the observed dynamics corresponded to the climatic conditions, showing particularly the negative effect of drought. The population was evenly distributed in the sampled soil profile, only avoiding the organic layer. Except for a locality in Poland, this is the easternmost record of the species.

Sarabande / P.O. Ferroud, comp.. Airs de ballet de "Platée" : choix / J.P. Rameau, comp. ; orchestre de la Société des grands concerts de Lyon ; G. M. Witkowski, dir.

Comprend : Sarabande ; Airs de ballet de Platée

Hitsausparametrien vaikutus rakenneteräksen MAG-hitsin laatuun

Työn tavoitteena oli löytää teräksen S355 MAG alapienahitsaukselle, 6mm:n levypaksuudelle sellaiset parametri-ikkunat, joissa hitsin ja perusaineen liittyminen on mahdollisimman jouheva. Hitsin laadunja hitsausparametrien välille pyritiin löytämään matemaattista korrelaatiota. Työ painottui hitsin muotoon sekä hitsin ja perusaineen liittymiseen. Työstä saatuja tuloksia käytettiin hitsattaessa väsytyskoekappaleita mutta niiden tutkiminen ei sisältynyt tähän työhön. Työssä haettiin parametreja a-mitaltaan 4mm:n alapienahitsille kahdeksalle yleisesti käytetylle hitsauslangalle, joista kolme oli umpilankaa, neljä metallitäytelankaa ja yksi rutiilitäytelanka ja kaasuina käytettiin kahta argon hiilidioksidi seoskaasua ja kahta argon helium seoskaasua.

Distribuição horizontal e vertical de fósforo em sistemas de cultivos exclusivos de soja e de integração lavoura-pecuária-floresta

O objetivo deste trabalho foi avaliar a distribuição horizontal e vertical do fósforo no solo e a produtividade de soja em sistemas de cultivos exclusivos e de integração lavoura-pecuária-floresta (ILPF). Foram avaliados os tratamentos: floresta plantada de eucalipto; lavoura de soja e milho safrinha consorciado com Urochloa brizantha 'Marandu'; pastagem de U. brizantha; sistema de ILPF; e duas áreas controle, com floresta nativa e pousio. O solo foi coletado nas camadas de 0-5, 5-10, 10-20 e 20-30 cm, para determinação das características químicas. As avaliações foram realizadas no segundo ano agrícola após a implantação do experimento. No sistema de ILPF, solo e produtividade foram avaliados em quatro transectos equidistantes, no centro do renque e a 3, 6, 10 e 15 m do renque, nas faces norte e sul. Os teores de P disponível (Mehlich-1) foram maiores nas camadas superficiais do solo, nos sistemas com soja/milho safrinha e com ILPF. No ILPF, os teores de P disponível não diferiram entre as distâncias do renque das árvores, e a produtividade de soja não diferiu da observada no sistema com soja/milho safrinha. Portanto, com dois anos de implantação, o sistema ILPF ainda não é capaz de interferir marcadamente nas características químicas do solo e na produtividade da soja.

Four-corner bone arthrodesis with dorsal rectangular plate: series and personal technique.

Controversy exists about the best method to achieve bone fusion in four-corner arthrodesis. Thirty-five patients who underwent this procedure by our technique were included in the study. Surgical indications were stage II-III SLAC wrist, stage II SNAC wrist and severe traumatic midcarpal joint injury. Mean follow-up was 4.6 years. Mean active flexion and extension were 34 degrees and 30 degrees respectively; grip strength recovery was 79%. Radiological consolidation was achieved in all cases. The mean DASH score was 23 and the postoperative pain improvement by visual analogue scale was statistically significant. Return to work was possible at 4 months for the average patient. Complications were a capitate fracture in one patient and the need for hardware removal in four cases. Four-corner bone wrist arthrodesis by dorsal rectangular plating achieves an acceptable preservation of range of motion with good pain relief, an excellent consolidation rate and minimal complications.

GIS and geodatabases application to global scale plate tectonics modelling

Les reconstructions palinspastiques fournissent le cadre idéal à de nombreuses études géologiques, géographiques, océanographique ou climatiques. En tant qu?historiens de la terre, les "reconstructeurs" essayent d?en déchiffrer le passé. Depuis qu?ils savent que les continents bougent, les géologues essayent de retracer leur évolution à travers les âges. Si l?idée originale de Wegener était révolutionnaire au début du siècle passé, nous savons depuis le début des années « soixante » que les continents ne "dérivent" pas sans but au milieu des océans mais sont inclus dans un sur-ensemble associant croûte « continentale » et « océanique »: les plaques tectoniques. Malheureusement, pour des raisons historiques aussi bien que techniques, cette idée ne reçoit toujours pas l'écho suffisant parmi la communauté des reconstructeurs. Néanmoins, nous sommes intimement convaincus qu?en appliquant certaines méthodes et certains principes il est possible d?échapper à l?approche "Wégenerienne" traditionnelle pour enfin tendre vers la tectonique des plaques. Le but principal du présent travail est d?exposer, avec tous les détails nécessaires, nos outils et méthodes. Partant des données paléomagnétiques et paléogéographiques classiquement utilisées pour les reconstructions, nous avons développé une nouvelle méthodologie replaçant les plaques tectoniques et leur cinématique au coeur du problème. En utilisant des assemblages continentaux (aussi appelés "assemblées clés") comme des points d?ancrage répartis sur toute la durée de notre étude (allant de l?Eocène jusqu?au Cambrien), nous développons des scénarios géodynamiques permettant de passer de l?une à l?autre en allant du passé vers le présent. Entre deux étapes, les plaques lithosphériques sont peu à peu reconstruites en additionnant/ supprimant les matériels océaniques (symbolisés par des isochrones synthétiques) aux continents. Excepté lors des collisions, les plaques sont bougées comme des entités propres et rigides. A travers les âges, les seuls éléments évoluant sont les limites de plaques. Elles sont préservées aux cours du temps et suivent une évolution géodynamique consistante tout en formant toujours un réseau interconnecté à travers l?espace. Cette approche appelée "limites de plaques dynamiques" intègre de multiples facteurs parmi lesquels la flottabilité des plaques, les taux d'accrétions aux rides, les courbes de subsidence, les données stratigraphiques et paléobiogéographiques aussi bien que les évènements tectoniques et magmatiques majeurs. Cette méthode offre ainsi un bon contrôle sur la cinématique des plaques et fournit de sévères contraintes au modèle. Cette approche "multi-source" nécessite une organisation et une gestion des données efficaces. Avant le début de cette étude, les masses de données nécessaires était devenues un obstacle difficilement surmontable. Les SIG (Systèmes d?Information Géographiques) et les géo-databases sont des outils informatiques spécialement dédiés à la gestion, au stockage et à l?analyse des données spatialement référencées et de leurs attributs. Grâce au développement dans ArcGIS de la base de données PaleoDyn nous avons pu convertir cette masse de données discontinues en informations géodynamiques précieuses et facilement accessibles pour la création des reconstructions. Dans le même temps, grâce à des outils spécialement développés, nous avons, tout à la fois, facilité le travail de reconstruction (tâches automatisées) et amélioré le modèle en développant fortement le contrôle cinématique par la création de modèles de vitesses des plaques. Sur la base des 340 terranes nouvellement définis, nous avons ainsi développé un set de 35 reconstructions auxquelles est toujours associé un modèle de vitesse. Grâce à cet ensemble de données unique, nous pouvons maintenant aborder des problématiques majeurs de la géologie moderne telles que l?étude des variations du niveau marin et des changements climatiques. Nous avons commencé par aborder un autre problème majeur (et non définitivement élucidé!) de la tectonique moderne: les mécanismes contrôlant les mouvements des plaques. Nous avons pu observer que, tout au long de l?histoire de la terre, les pôles de rotation des plaques (décrivant les mouvements des plaques à la surface de la terre) tendent à se répartir le long d'une bande allant du Pacifique Nord au Nord de l'Amérique du Sud, l'Atlantique Central, l'Afrique du Nord, l'Asie Centrale jusqu'au Japon. Fondamentalement, cette répartition signifie que les plaques ont tendance à fuir ce plan médian. En l'absence d'un biais méthodologique que nous n'aurions pas identifié, nous avons interprété ce phénomène comme reflétant l'influence séculaire de la Lune sur le mouvement des plaques. La Lune sur le mouvement des plaques. Le domaine océanique est la clé de voute de notre modèle. Nous avons attaché un intérêt tout particulier à le reconstruire avec beaucoup de détails. Dans ce modèle, la croûte océanique est préservée d?une reconstruction à l?autre. Le matériel crustal y est symbolisé sous la forme d?isochrones synthétiques dont nous connaissons les âges. Nous avons également reconstruit les marges (actives ou passives), les rides médio-océaniques et les subductions intra-océaniques. En utilisant ce set de données très détaillé, nous avons pu développer des modèles bathymétriques 3-D unique offrant une précision bien supérieure aux précédents.<br/><br/>Palinspastic reconstructions offer an ideal framework for geological, geographical, oceanographic and climatology studies. As historians of the Earth, "reconstructers" try to decipher the past. Since they know that continents are moving, geologists a trying to retrieve the continents distributions through ages. If Wegener?s view of continent motions was revolutionary at the beginning of the 20th century, we know, since the Early 1960?s that continents are not drifting without goal in the oceanic realm but are included in a larger set including, all at once, the oceanic and the continental crust: the tectonic plates. Unfortunately, mainly due to technical and historical issues, this idea seems not to receive a sufficient echo among our particularly concerned community. However, we are intimately convinced that, by applying specific methods and principles we can escape the traditional "Wegenerian" point of view to, at last, reach real plate tectonics. This is the main aim of this study to defend this point of view by exposing, with all necessary details, our methods and tools. Starting with the paleomagnetic and paleogeographic data classically used in reconstruction studies, we developed a modern methodology placing the plates and their kinematics at the centre of the issue. Using assemblies of continents (referred as "key assemblies") as anchors distributed all along the scope of our study (ranging from Eocene time to Cambrian time) we develop geodynamic scenarios leading from one to the next, from the past to the present. In between, lithospheric plates are progressively reconstructed by adding/removing oceanic material (symbolized by synthetic isochrones) to major continents. Except during collisions, plates are moved as single rigid entities. The only evolving elements are the plate boundaries which are preserved and follow a consistent geodynamical evolution through time and form an interconnected network through space. This "dynamic plate boundaries" approach integrates plate buoyancy factors, oceans spreading rates, subsidence patterns, stratigraphic and paleobiogeographic data, as well as major tectonic and magmatic events. It offers a good control on plate kinematics and provides severe constraints for the model. This multi-sources approach requires an efficient data management. Prior to this study, the critical mass of necessary data became a sorely surmountable obstacle. GIS and geodatabases are modern informatics tools of specifically devoted to store, analyze and manage data and associated attributes spatially referenced on the Earth. By developing the PaleoDyn database in ArcGIS software we converted the mass of scattered data offered by the geological records into valuable geodynamical information easily accessible for reconstructions creation. In the same time, by programming specific tools we, all at once, facilitated the reconstruction work (tasks automation) and enhanced the model (by highly increasing the kinematic control of plate motions thanks to plate velocity models). Based on the 340 terranes properly defined, we developed a revised set of 35 reconstructions associated to their own velocity models. Using this unique dataset we are now able to tackle major issues of the geology (such as the global sea-level variations and climate changes). We started by studying one of the major unsolved issues of the modern plate tectonics: the driving mechanism of plate motions. We observed that, all along the Earth?s history, plates rotation poles (describing plate motions across the Earth?s surface) tend to follow a slight linear distribution along a band going from the Northern Pacific through Northern South-America, Central Atlantic, Northern Africa, Central Asia up to Japan. Basically, it sighifies that plates tend to escape this median plan. In the absence of a non-identified methodological bias, we interpreted it as the potential secular influence ot the Moon on plate motions. The oceanic realms are the cornerstone of our model and we attached a particular interest to reconstruct them with many details. In this model, the oceanic crust is preserved from one reconstruction to the next. The crustal material is symbolised by the synthetic isochrons from which we know the ages. We also reconstruct the margins (active or passive), ridges and intra-oceanic subductions. Using this detailed oceanic dataset, we developed unique 3-D bathymetric models offering a better precision than all the previously existing ones.