Granulomatous uveitis and congenital cataract: a rare association.

INTRODUCTION: The association of a granulomatous uveitis and congenital cataract and is rarely observed in newborn children. We describe the history of two patients presenting simultaneously with these two features in the absence of a TORCH infection. PATIENTS AND METHODS: The first patient, a boy born in 1997, presented to our hospital two days after birth with multiples Koeppe's and Busacca's nodules and bilateral cataract. The second patient, a boy born in 2006, was referred two weeks after birth. He presented with a severe unilateral granulomatous uveitis, multiples iris nodules, a high intraocular pressure of 45 mmHg and a congenital cataract. THERAPY AND OUTCOME: Lens extraction produced a rapid resolution of uveitis in these two patients. TORCH infection was ruled out in both children by history, extensive serologies performed simultaneously in mother and child or PCR of ocular fluids. CONCLUSIONS: A congenital cataract associated with a granulomatous uveitis is an extremely rare association. The removal of the lens resulted in complete resolution of the inflammation: a phacogenic mechanism could be at the origin of ocular inflammation in both cases.

After Satan: Essays in Honour of Neil Forsyth

This volume is the result of a collective desire to pay homage to Neil Forsyth, whose work has significantly contributed to scholarship on Satan. This volume is "after" Satan in more ways than one, tracing the afterlife of both the satanic figure in literature and of Neil Forsyth's contribution to the field, particularly in his major books The Old Enemy: Satan and the Combat Myth (Princeton University Press, 1987, revised 1990) and The Satanic Epic (Princeton University Press, 2003). The essays in this volume draw on Forsyth's work as a focus for their analyses of literary encounters with evil or with the Devil himself, reflecting the richness and variety of contemporary approaches to the age-old question of how to represent evil. All the contributors acknowledge Neil Forsyth's influence in the study of both the Satan-figure and Milton's Paradise Lost. But beyond simply paying homage to Neil Forsyth, the articles collected here trace the lineage of the Satan figure through literary history, showing how evil can function as a necessary other against which a community may define itself. They chart the demonised other through biblical history and medieval chronicle, Shakespeare and Milton, to nineteenth-century fiction and the contemporary novel. Many of the contributors find that literary evil is mediated through the lens of the Satan of Paradise Lost, and their articles address the notion, raised by Neil Forsyth in The Satanic Epic, that the literary Devil-figures under consideration are particularly interested in linguistic ambivalence and the twisted texture of literary works themselves. The multiple responses to evil and the continuous reinvention of the devil figure through the centuries all reaffirm the textual presence of the Devil, his changing forms necessarily inscribed in the shifting history of western literary culture. These essays are a tribute to the work of Neil Forsyth, whose scholarship has illuminated and guided the study of the Devil in English and other literatures.

Morgagnian cataract simulating iris neoplasia : case report

Purpose: to describe a case in which the diagnosis of Morganian cataract required clinical and instrumental differentiation from iris pathologies, including iris melanoma. Methods: a 60-years-old Caucasian man referred to our institute for worsening of vision in last few months. Clinical evaluation consisted in complete ophthalmological assessment, ultrasound examination (biomicroscopy and 20MHz), and Magnetic Resonance Imaging (MRI) completed with Susceptibility Weighted Imaging (SWI). Results: traumatic corneal wound of the left eye (LE) had occurred 5 years before, and was treated with medical therapy alone. Best-corrected visual acuity (BCVA) was 3/10 in the right eye (RE) and finger count in the LE, with intraocular pressure at 13 and 20mmHg, respectively. Chronic central serous chorioretinopathy, accounted for the low visual acuity of the RE. Slit-lamp biomicroscopy of the LE was as in Figure 1; LE fundus was not clinically observable. Despite MRI was compatible with an iris solid formation, characterized by contrast enhancement and hyperintense signal in SWI, ultrasound indicated rather a mixed solid and liquid content (moderately echogenic external layer, hyporeflective internal content). Iris root and ciliary body were not significantly altered; the lens showed inhomogeneous content. We considered Morgagnian cataract the most probable diagnosis. Surgery confirmed the presence of a hypermature cataract with prior anterior capsule fissuring; the liquefied cortex infiltrated the iris without anterior chamber seeping. Post-operative BCVA was 3/10 and fundus examination disclosed an advanced macular chronic central serous chorioretinopathy. Conclusions: In the reported case a previous perforating trauma have probably damaged the lens capsule and started cataract progression. Curiously cataract developed percolating into the iris stroma, thus simulating an iris mass. At our knowledge, Morgagnian cataract has never been included in the differential diagnosis of iris mass.

Monetary policy and rational asset price bubbles

I examine the impact of alternative monetary policy rules on arational asset price bubble, through the lens of an overlapping generations model with nominal rigidities. A systematic increase in interestrates in response to a growing bubble is shown to enhance the fluctuations in the latter, through its positive effect on bubble growth. Theoptimal monetary policy seeks to strike a balance between stabilization of the bubble and stabilization of aggregate demand. The paper'smain findings call into question the theoretical foundations of the casefor "leaning against the wind" monetary policies.

New multiple matched filter: design and experimental realization

A method of making a multiple matched filter which allows the recognition of different characters in successive planes in simple conditions is proposed. The generation of the filter is based on recording on the same plate the Fourier transforms of the different patterns to be recognized, each of which is affected by different spherical phase factors because the patterns have been placed at different distances from the lens. This is proved by means of experiments with a triple filter which allows satisfactory recognition of three characters.

Wage cuts and managers' empathy: How a positive emotion can contribute to positive organizational ethics in difficult times

Using the lens of positive organizational ethics, we theorized that empathy affects decisions in ethical dilemmas that concern the well-being of not only the organization but also other stakeholders. We hypothesized and found that empathetic managers were less likely to comply with requests by an authority figure to cut the wages of their employees than were non-empathetic managers. However, when an authority figure requested to hold wages constant, empathy did not affect wage cut decisions. These findings imply that empathy can serve as a safeguard for ethical decision making in organizations during trying times without generally undermining organizational effectiveness. We conclude by discussing the implications of our research.

Linssinpoistoleikkaus fakoemulsifikaatiomenetelmällä

Summary: Phacoemulsification of the lens

New multiple matched filter: design and experimental realization

A method of making a multiple matched filter which allows the recognition of different characters in successive planes in simple conditions is proposed. The generation of the filter is based on recording on the same plate the Fourier transforms of the different patterns to be recognized, each of which is affected by different spherical phase factors because the patterns have been placed at different distances from the lens. This is proved by means of experiments with a triple filter which allows satisfactory recognition of three characters.

Critical Mobilities

The field of mobility studies examines social phenomena through the lens of movement. In this perspective, societies are regarded as being constantly reconfigured as they are shaped by a series of mobile entities (capital, people, information). This book engages critically with many of the claims and challenges of mobility studies by providing empirically rich reports of mobilities and their limitations. Instead of assuming a seamless world of flows, the volume foregrounds questions of power, inequality, and moorings as integral to the movement of capital, goods, images, practices, or people. It brings together the work of several internationally renowned scholars, who engage with these movements at critical sites. This is the first book to provide a critical and interdisciplinary view of mobilities covering a broad range of issues rather than a single domain. The chapters deal with current and important issues, such as organ transplants, illegal migrations, urban globalization, international policies of higher education institutions, and scientific diasporas. As a whole, the book provides new insights into how power relations shape mobilities and societies.

War and National Renewal: Civil Religion and Blood Sacrifice in American Culture

Wars are often associated with a rhetoric of renewal or new beginnings. This essay explores this claim through the lens of civil religion and a recent book by Carolyn Marvin and David Ingle, Blood Sacrifice and the Nation, which combines Emile Durkheim with Réné Girard in proposing that modern national cohesion depends on blood sacrifice. I unpack some of the paradoxes raised by this theory of national renewal in the context of 9/11, with a special focus on the sacred status of the flag and the special attention given to uniformed serviceman in the American body politic.

CO2 Laser Cutting of Particleboard, HDF and MDF

The purpose of this thesis is to reveal how the laser cutting parameters influence lasercutting of particleboard, HDF and MDF. The literature review introduces the basic principle of CO2 laser, CO2 laser equipment and its usage in cutting of wood-based materials. The experimental part focuses on the discussion and analysis ofthe test data and attempts to draw conclusions on the influence of various parameters, including laser power, focal length of the lens and cutting gas, on the cutting speed and kerf quality. The tested materials include various thicknesses of particleboard, HDF and MDF samples. A TRUMPF TLF2700 HQ laser equipment was used for the experiments. To obtain valid data, the test samples must be completely cut through without any bonding of wood fibre. The maximum cutting speed is linear dependent on the laser power in thecondition that the other parameters are constant. For each thickness of a specific material type, there is a minimum laser power for cutting. Normally, the topand bottom kerf widths increase with the enhancement of laser power. There may be a critical laser power which can generate the minimum cross-sectional kerf width. Lens of larger focal length may achieve higher cutting speed. As the focal length becomes larger, the top kerf width tends to increase while the bottom andcross-sectional kerf widths to the opposite. Of all cutting gases, oxygen can help achieve higher cutting speed. The gas pressure of nitrogen does not seem to have strong influence on the cutting result. Generally, 2 bar air is more preferable for higher cutting speed. For particleboard and MDF samples of larger thickness than 12 mm, 2 bar argon can be used to reach remarkably higher cutting speed than the 5 bar. Generally, the 190.5 mm lens can produce smallest total kerf width. The kerf sides of thicker samples are darker than the thinner ones. The sample darkness tends to be lower as laser power increased. 63.5 mm lens seemed tocause more darkness than other lens. 5 bar cutting gases can produce less dark side kerfs than 2 bar ones. Oxygen normally causes darker kerfs than other gases. No distinct differences were found between nitrogen and argon.

CO2-laserin soveltaminen WFU-paperin reunan leikkaamiseen

Tämän diplomityön tarkoitus oli selvittää CO2-laserin soveltuvuutta paperin reunan leikkaamiseen ennen liimapuristinta nopealle modernilleWFU-paperikoneelle. Merkittävimmät leikkauskokeet tehtiin leikkaamalla paperirataa todenmukaisissa olosuhteissa koekoneella. Koeleikkauksissa tutkittiin myös päällystettyjen paperilajien CO2-laserleikkausta. Paperin reunan koeleikkauksia suoritettiin leikkauspöytää vasten sekä telaa vasten. Leikkauspöytänä käytettiin korkeapainevesileikkaimelle suunniteltua leikkauspöytää, jota paranneltiin tämän työn yhteydessä paremmin laserleikkaukselle sopivaksi. Telaa vasten suoritetuilla leikkauksilla lasertehon tarve oli suurempi verrattuna pöytää vasten leikkaukseen samalla leikkausnopeudella ja samalla paperilajilla. Laserlaitteiston mitoittaminen oikein pelkkien arkkileikkauskokeiden perusteella ei ollut mahdollista. Myös rullilla tapahtuvia leikkauskokeita tarvittiin. Pöytää vasten tapahtuvaan leikkaamiseen tarvitaan 1000 W laserlaite paperin molemmille reunoille. Tämän tehoiset laserlaitteet riittävät kaikille Changshun PK 1:n paperilajeille niiden lajikohtaiseen maksimiajonopeuteen. Testatuista kolmesta polttovälistä antoi 5" polttoväli parhaat leikkaustulokset. Polttopisteen paikka voi vaihdella ± 0.75 mm paperin pinnasta vaikuttamatta silti merkittävästi lasertehon tarpeeseen. Laserleikatun paperin reuna oli hyvälaatuinen, eikä laserleikkaus aiheuttanut paperille epätoivottuja asioita kuten mustumista.

Spectrometrical Monitoring of Laser Sintering Process of Ceramic Material

This thesis is done as a part of project called FuncMama that is a project between Technical Research Centre of Finland (VTT), Oulu University (OY), Lappeenranta University of Technology (LUT) and Finnish industrial partners. Main goal of the project is to manufacture electric and mechanical components from mixed materials using laser sintering. Aim of this study was to create laser sintered pieces from ceramic material and monitor the sintering event by using spectrometer. Spectrometer is a device which is capable to record intensity of different wavelengths in relation with time. In this study the monitoring of laser sintering was captured with the equipment which consists of Ocean Optics spectrometer, optical fiber and optical lens (detector head). Light from the sintering process hit first to the lens system which guides the light in to the optical fibre. Optical fibre transmits the light from the sintering process to the spectrometer where wavelengths intensity level information is detected. The optical lens of the spectrometer was rigidly set and did not move along with the laser beam. Data which was collected with spectrometer from the laser sintering process was converted with Excel spreadsheet program for result’s evaluation. Laser equipment used was IPG Photonics pulse fibre laser. Laser parameters were kept mainly constant during experimental part and only sintering speed was changed. That way it was possible to find differences in the monitoring results without fear of too many parameters mixing together and affecting to the conclusions. Parts which were sintered had one layer and size of 5 x 5 mm. Material was CT2000 – tape manufactured by Heraeus which was later on post processed to powder. Monitoring of different sintering speeds was tested by using CT2000 reference powder. Moreover tests how different materials effect to the process monitoring were done by adding foreign powder Du Pont 951 which had suffered in re-grinding and which was more reactive than CT2000. By adding foreign material it simulates situation where two materials are accidently mixed together and it was studied if that can be seen with the spectrometer. It was concluded in this study that with the spectrometer it is possible to detect changes between different laser sintering speeds. When the sintering speed is lowered the intensity level of light is higher from the process. This is a result of higher temperature at the sintering spot and that can be noticed with the spectrometer. That indicates it could be possible to use spectrometer as a tool for process observation and support the idea of having system that can help setting up the process parameter window. Also important conclusion was how well the adding of foreign material could be seen with the spectrometer. When second material was added a significant intensity level raise could be noticed in that part where foreign material was mixed. That indicates it is possible to see if there are any variations in the material or if there are more materials mixed together. Spectrometric monitoring of laser sintering could be useful tool for process window observation and temperature controlling of the sintering process. For example if the process window for specific material is experimentally determined to get wanted properties and satisfying sintering speed. It is possible if the data is constantly recorded that the results can show faults in the part texture between layers. Changes between the monitoring data and the experimentally determined values can then indicate changes in the material being generated by material faults or by wrong process parameters. The results of this study show that spectrometer could be one possible tool for monitoring. But to get in that point where this all can be made possible much more researching is needed.

How Lean Six Sigma and Agile principles optimize ITIL-based processes

Imagine the potential implications of an organization whose business and IT processes are well aligned and are capable of reactively and proactively responding to the external and internal changes. The Philips IT Infrastructure and Operations department (I&O) is undergoing a series of transformation activities to help Philips business keeping up with the changes. I&O would serve a critical function in any business sectors; given that the I&O’s strategy switched from “design, build and run” to “specify, acquire and performance manage”, that function is amplified. In 2013, I&O’s biggest transforming programme I&O Futures engaged multiple interdisciplinary departments and programs on decommissioning legacy processes and restructuring new processes with respect to the Information Technology Internet Library (ITIL), helping I&O to achieve a common infrastructure and operating platform (CI&OP). The author joined I&O Futures in the early 2014 and contributed to the CI&OP release 1, during which a designed model Bing Box and its evaluations were conducted through the lens of six sigma’s structured define-measure-analyze-improve-control (DMAIC) improvement approach. This Bing Box model was intended to firstly combine business and IT principles, namely Lean IT, Agile, ITIL best practices, and Aspect-oriented programming (AOP) into a framework. Secondly, the author implemented the modularized optimization cycles according to the defined framework into Philips’ ITIL-based processes and, subsequently, to enhance business process performance as well as to increase efficiency of the optimization cycles. The unique of this thesis is that the Bing Box model not only provided comprehensive optimization approaches and principles for business process performance, but also integrated and standardized optimization modules for the optimization process itself. The research followed a design research guideline that seek to extend the boundaries of human and organizational capabilities by creating new and innovative artifacts. The Chapter 2 firstly reviewed the current research on Lean Six Sigma, Agile, AOP and ITIL, aiming at identifying the broad conceptual bases for this study. In Chapter 3, we included the process of constructing the Bing Box model. The Chapter 4 described the adoption of Bing Box model: two-implementation case validated by stakeholders through observations and interviews. Chapter 5 contained the concluding remarks, the limitation of this research work and the future research areas. Chapter 6 provided the references used in this thesis.

Motives and barriers for engaging in collaborative consumption in Finland

In this thesis the consumers’ expected motives and barriers for engaging in collaborative consumption in Finland are studied. The phenomenon is observed through the lens of consumer theory and it is connected to the context using Hofstede’s 6-D model. The phenomenon is new and there are almost no recorded results in the background research, and when considering the limitations of this study, there are no results at all. Therefore, combining different kinds of literature, as well as taking along consumer theory and Hofstede’s model that explains cultural factors, it was possible to compile a comprehensive general view of the present state of the phenomenon. The actual study was conducted using qualitative methods and the solution was sought collecting data from six in-depth interviews with interviewees having experience from using, or offering resources, or both. According to the results, the primary motive in all modes of consumption was economic. Anti-materialism, anti-consumption, and expanding lifestyle were another a bit more general motives. Perceived barriers were, especially as a new result, the amount of trouble one has to see and in single modes, a lack of trust, the used platform and too expensive prices.