Intense green-yellow electroluminescence from Tb+-implanted silicon-rich silicon nitride/oxide light emitting devices

High optical power density of 0.5 mW/cm2, external quantum efficiency of 0.1%, and population inversion of 7% are reported from Tb+-implanted silicon-rich silicon nitride/oxide light emitting devices. Electrical and electroluminescence mechanisms in these devices were investigated. The excitation cross section for the 543 nm Tb3+ emission was estimated under electrical pumping, resulting in a value of 8.2 × 10−14 cm2, which is one order of magnitude larger than one reported for Tb3+:SiO2 light emitting devices. These results demonstrate the potentiality of Tb+-implanted silicon nitride material for the development of integrated light sources compatible with Si technology.

Model for the emission of Si+ ions during oxygen bombardment of Si(100) surfaces

The variation in the emission of Si+ ions from ion-beam-induced oxidized silicon surfaces has been studied. The stoichiometry and the electronic structure of the altered layer has been characterized using x-ray photoelectron spectroscopy (XPS). The XPS analysis of the Si 2p core level indicates the strong presence of suboxide chemical states when bombarding at angles of incidence larger than 30 °. Since the surface stoichiometry or degree of oxidation varies with the angle of incidence, the corresponding valence-band structures also differ among each other. A comparison between experimental measurements and theoretically calculated Si and SiO2 valence bands indicates that the valence bands for the altered layers are formed by a combination of those two. Since Si-Si bonds are present in the suboxide molecules, the top of the respective new valence bands are formed by the corresponding 3p-3p Si-like subbands, which extend up to the Si Fermi level. The changes in stoichiometry and electronic structure have been correlated with the emission of Si+ ions from these surfaces. From the results a general model for the Si+ ion emission is proposed combining the resonant tunneling and local-bond-breaking models.

Evolução quantitativa de planossolos do agreste do estado de Pernambuco

A pedogênese dos solos planossólicos, especialmente da região do Agreste de Pernambuco, tem sido pouco estudada, havendo indicações e dúvidas relativas a alguns aspectos como a possível dualidade ou retrabalhamentos diferenciados na formação do material de origem, total das perdas e ganhos e a relativa mobilidade dos principais elementos constitutivos durante a evolução dos solos. Foram estudados três solos com marcantes contrastes texturais em uma topossequência da região. Foram estudados três solos com marcantes contrastes texturais em uma topossequência no Agreste de Pernambuco. Os objetivos da pesquisa foram averiguar a compatibilidade dos solos com os materiais geológicos subjacentes e avaliar quantitativamente as perdas e os ganhos ocorridos durante a pedogênese. Para isso foram realizadas análises química total e de zircônio (Zr) e quartzo, tomados como base para determinação de um índice de intemperização, em todos os horizontes dos solos e no material de origem. Verificou-se que os solos são constituídos por materiais autóctones, com apenas pequenas indicações de retrabalhamento dos materiais mais superficiais. Durante o processo de intemperização ou pedogênese, verificou-se perda de, aproximadamente, 50 % do peso original do solo. As perdas referentes aos principais elementos constituintes dos solos apresentaram a seguinte ordem: MgO > CaO > Fe2O3 > Al2O3 > SiO2. Os nítidos contrastes texturais, devido à argilização dos horizontes Bt, parecem ser principalmente resultado de uma combinação de outros processos, que não simples eluviação-iluviação.

Raman microstructural analysis of silicon-on-insulator formed by high dose oxygen ion implantation: As-implanted structures

A microstructural analysis of silicon-on-insulator samples obtained by high dose oxygen ion implantation was performed by Raman scattering. The samples analyzed were obtained under different conditions thus leading to different concentrations of defects in the top Si layer. The samples were implanted with the surface covered with SiO2 capping layers of different thicknesses. The spectra measured from the as-implanted samples were fitted to a correlation length model taking into account the possible presence of stress effects in the spectra. This allowed quantification of both disorder effects, which are determined by structural defects, and residual stress in the top Si layer before annealing. These data were correlated to the density of dislocations remaining in the layer after annealing. The analysis performed corroborates the existence of two mechanisms that generate defects in the top Si layer that are related to surface conditions during implantation and the proximity of the top Si/buried oxide layer interface to the surface before annealing.

Relações solo-paisagem em uma topossequência sobre substrato granítico em Santo Antônio do Matupi, Manicoré (AM)

Considerando as dimensões da região amazônica e a necessidade de estudos que estabeleçam conexões entre os solos e a expressão da paisagem, o objetivo deste trabalho foi estudar as relações solo-paisagem em uma topossequência sobre substrato granítico em Santo Antônio do Matupi, Manicoré, AM. Foi estabelecido um caminhamento de 3.000 m a partir do "espigão" da vertente, no seu sentido mais suave, com identificação dos segmentos da vertente com base na "quebra" do declive do terreno. Foram abertas trincheiras nos segmentos de vertente mapeados, e perfis foram caracterizados morfologicamente, coletando-se amostras de seus horizontes. Foram realizadas análises físicas (textura, ADA e GF, Ds e Dp, Pt e CHSS), químicas (pH em água e KCl, Ca, Mg, K, Na e Al trocáveis, P disponível, H + Al e C orgânico; SiO2, Al2O3 e Fe2O3 (método do H2SO4) e óxidos de Fe "livres" extraído com ditionito-citrato-bicarbonato e o Fe mal cristalizado extraído com oxalato de amônio) e mineralógicas (frações areia, silte e argila), usando difratometria de raios X. As variações do relevo favoreceram a presença de solos distróficos nos topos e solos eutróficos no sopé de transporte. As variáveis ΔpH, relação silte/argila, V % e relação Fed/Fet indicaram a presença de solos mais intemperizados nas áreas de topo da paisagem e solos com menor grau de evolução na encosta e no sopé de transporte. A composição mineralógica da fração argila mostrou-se relativamente homogênea, com predominância de caulinita e gibbsita e menor proporção de mica e quartzo.

Relações solo-superfície geomórfica em uma topossequência várzea-terra firme na região de Humaitá (AM)

O conceito de superfície geomórfica permite uma interligação entre os diferentes ramos da ciência do solo, tais como geologia, geomorfologia e pedologia. O objetivo deste trabalho foi estudar as relações solo-superfície geomórfica em uma topossequência de 4.500 m na transição várzea/terra firme, na região de Humaitá (AM). Do divisor de águas até a planície do rio Madeira, as superfícies geomórficas foram identificadas com base na ruptura do declive do terreno, em critérios estratigráficos e em outras observações de campo. Foram abertas trincheiras nos segmentos mapeados da topossequência, os perfis de solos foram caracterizados morfologicamente e amostras foram coletadas de seus horizontes. Foram realizadas análises físicas de granulometria, argila dispersa em água, grau de floculação, densidade do solo, densidade das partículas, porosidade total e condutividade hidráulica do solo saturado. As análises químicas incluíram pH em água e KCl; Ca, Mg, K, Na e Al trocáveis; P disponível; H + Al e C orgânico; SiO2, Al2O3 e Fe2O3 do ataque sulfúrico; Fe "livre" extraído com ditionito-citrato-bicarbonato; e ferro mal cristalizado, extraído com oxalato de amônio. Os índices ∆pH, relação silte/argila, Ki e Fe d/Fe t indicaram solos mais intemperizados na parte mais elevada da paisagem em comparação ao declive de infiltração, declive convexo e sopé aluvial, coincidindo com a maior idade da superfície geomórfica I em relação às superfícies geomórficas II e III. As variações dos solos na transeção estudada mostraram solos mais intemperizados nos ambientes de terra firme quando comparados aos solos dos ambientes de várzeas. O entendimento dos eventos geomórficos favoreceu a compreensão da variação dos atributos dos solos na topossequência.

Assessment of the occurrence of nanoparticles in Swiss industry and evaluation of the appropriatenesss of the measurement devices to determine the workforce exposure

Abstract : The occupational health risk involved with handling nanoparticles is the probability that a worker will experience an adverse health effect: this is calculated as a function of the worker's exposure relative to the potential biological hazard of the material. Addressing the risks of nanoparticles requires therefore knowledge on occupational exposure and the release of nanoparticles into the environment as well as toxicological data. However, information on exposure is currently not systematically collected; therefore this risk assessment lacks quantitative data. This thesis aimed at, first creating the fundamental data necessary for a quantitative assessment and, second, evaluating methods to measure the occupational nanoparticle exposure. The first goal was to determine what is being used where in Swiss industries. This was followed by an evaluation of the adequacy of existing measurement methods to assess workplace nanopaiticle exposure to complex size distributions and concentration gradients. The study was conceived as a series of methodological evaluations aimed at better understanding nanoparticle measurement devices and methods. lt focused on inhalation exposure to airborne particles, as respiration is considered to be the most important entrance pathway for nanoparticles in the body in terms of risk. The targeted survey (pilot study) was conducted as a feasibility study for a later nationwide survey on the handling of nanoparticles and the applications of specific protection means in industry. The study consisted of targeted phone interviews with health and safety officers of Swiss companies that were believed to use or produce nanoparticles. This was followed by a representative survey on the level of nanoparticle usage in Switzerland. lt was designed based on the results of the pilot study. The study was conducted among a representative selection of clients of the Swiss National Accident Insurance Fund (SUVA), covering about 85% of Swiss production companies. The third part of this thesis focused on the methods to measure nanoparticles. Several pre- studies were conducted studying the limits of commonly used measurement devices in the presence of nanoparticle agglomerates, This focus was chosen, because several discussions with users and producers of the measurement devices raised questions about their accuracy measuring nanoparticle agglomerates and because, at the same time, the two survey studies revealed that such powders are frequently used in industry. The first preparatory experiment focused on the accuracy of the scanning mobility particle sizer (SMPS), which showed an improbable size distribution when measuring powders of nanoparticle agglomerates. Furthermore, the thesis includes a series of smaller experiments that took a closer look at problems encountered with other measurement devices in the presence of nanoparticle agglomerates: condensation particle counters (CPC), portable aerosol spectrometer (PAS) a device to estimate the aerodynamic diameter, as well as diffusion size classifiers. Some initial feasibility tests for the efficiency of filter based sampling and subsequent counting of carbon nanotubes (CNT) were conducted last. The pilot study provided a detailed picture of the types and amounts of nanoparticles used and the knowledge of the health and safety experts in the companies. Considerable maximal quantities (> l'000 kg/year per company) of Ag, Al-Ox, Fe-Ox, SiO2, TiO2, and ZnO (mainly first generation particles) were declared by the contacted Swiss companies, The median quantity of handled nanoparticles, however, was 100 kg/year. The representative survey was conducted by contacting by post mail a representative selection of l '626 SUVA-clients (Swiss Accident Insurance Fund). It allowed estimation of the number of companies and workers dealing with nanoparticles in Switzerland. The extrapolation from the surveyed companies to all companies of the Swiss production sector suggested that l'309 workers (95%-confidence interval l'073 to l'545) of the Swiss production sector are potentially exposed to nanoparticles in 586 companies (145 to l'027). These numbers correspond to 0.08% (0.06% to 0.09%) of all workers and to 0.6% (0.2% to 1.1%) of companies in the Swiss production sector. To measure airborne concentrations of sub micrometre-sized particles, a few well known methods exist. However, it was unclear how well the different instruments perform in the presence of the often quite large agglomerates of nanostructured materials. The evaluation of devices and methods focused on nanoparticle agglomerate powders. lt allowed the identification of the following potential sources of inaccurate measurements at workplaces with considerable high concentrations of airborne agglomerates: - A standard SMPS showed bi-modal particle size distributions when measuring large nanoparticle agglomerates. - Differences in the range of a factor of a thousand were shown between diffusion size classifiers and CPC/SMPS. - The comparison between CPC/SMPS and portable aerosol Spectrometer (PAS) was much better, but depending on the concentration, size or type of the powders measured, the differences were still of a high order of magnitude - Specific difficulties and uncertainties in the assessment of workplaces were identified: the background particles can interact with particles created by a process, which make the handling of background concentration difficult. - Electric motors produce high numbers of nanoparticles and confound the measurement of the process-related exposure. Conclusion: The surveys showed that nanoparticles applications exist in many industrial sectors in Switzerland and that some companies already use high quantities of them. The representative survey demonstrated a low prevalence of nanoparticle usage in most branches of the Swiss industry and led to the conclusion that the introduction of applications using nanoparticles (especially outside industrial chemistry) is only beginning. Even though the number of potentially exposed workers was reportedly rather small, it nevertheless underscores the need for exposure assessments. Understanding exposure and how to measure it correctly is very important because the potential health effects of nanornaterials are not yet fully understood. The evaluation showed that many devices and methods of measuring nanoparticles need to be validated for nanoparticles agglomerates before large exposure assessment studies can begin. Zusammenfassung : Das Gesundheitsrisiko von Nanopartikel am Arbeitsplatz ist die Wahrscheinlichkeit dass ein Arbeitnehmer einen möglichen Gesundheitsschaden erleidet wenn er diesem Stoff ausgesetzt ist: sie wird gewöhnlich als Produkt von Schaden mal Exposition gerechnet. Für eine gründliche Abklärung möglicher Risiken von Nanomaterialien müssen also auf der einen Seite Informationen über die Freisetzung von solchen Materialien in die Umwelt vorhanden sein und auf der anderen Seite solche über die Exposition von Arbeitnehmenden. Viele dieser Informationen werden heute noch nicht systematisch gesarnmelt und felilen daher für Risikoanalysen, Die Doktorarbeit hatte als Ziel, die Grundlagen zu schaffen für eine quantitative Schatzung der Exposition gegenüber Nanopartikel am Arbeitsplatz und die Methoden zu evaluieren die zur Messung einer solchen Exposition nötig sind. Die Studie sollte untersuchen, in welchem Ausmass Nanopartikel bereits in der Schweizer Industrie eingesetzt werden, wie viele Arbeitnehrner damit potentiel] in Kontakt komrrien ob die Messtechnologie für die nötigen Arbeitsplatzbelastungsmessungen bereits genügt, Die Studie folcussierte dabei auf Exposition gegenüber luftgetragenen Partikel, weil die Atmung als Haupteintrittspforte iïlr Partikel in den Körper angesehen wird. Die Doktorarbeit besteht baut auf drei Phasen auf eine qualitative Umfrage (Pilotstudie), eine repräsentative, schweizerische Umfrage und mehrere technische Stndien welche dem spezitischen Verständnis der Mëglichkeiten und Grenzen einzelner Messgeräte und - teclmikeri dienen. Die qualitative Telephonumfrage wurde durchgeführt als Vorstudie zu einer nationalen und repräsentativen Umfrage in der Schweizer Industrie. Sie zielte auf Informationen ab zum Vorkommen von Nanopartikeln, und den angewendeten Schutzmassnahmen. Die Studie bestand aus gezielten Telefoninterviews mit Arbeit- und Gesundheitsfachpersonen von Schweizer Unternehmen. Die Untemehmen wurden aufgrund von offentlich zugànglichen lnformationen ausgewählt die darauf hinwiesen, dass sie mit Nanopartikeln umgehen. Der zweite Teil der Dolctorarbeit war die repräsentative Studie zur Evalniernng der Verbreitnng von Nanopaitikelanwendungen in der Schweizer lndustrie. Die Studie baute auf lnformationen der Pilotstudie auf und wurde mit einer repräsentativen Selektion von Firmen der Schweizerischen Unfall Versicherungsanstalt (SUVA) durchgeüihxt. Die Mehrheit der Schweizerischen Unternehmen im lndustrieselctor wurde damit abgedeckt. Der dritte Teil der Doktorarbeit fokussierte auf die Methodik zur Messung von Nanopartikeln. Mehrere Vorstudien wurden dnrchgefîihrt, um die Grenzen von oft eingesetzten Nanopartikelmessgeräten auszuloten, wenn sie grösseren Mengen von Nanopartikel Agglomeraten ausgesetzt messen sollen. Dieser F okns wurde ans zwei Gründen gewählt: weil mehrere Dislcussionen rnit Anwendem und auch dem Produzent der Messgeràte dort eine Schwachstelle vermuten liessen, welche Zweifel an der Genauigkeit der Messgeräte aufkommen liessen und weil in den zwei Umfragestudien ein häufiges Vorkommen von solchen Nanopartikel-Agglomeraten aufgezeigt wurde. i Als erstes widmete sich eine Vorstndie der Genauigkeit des Scanning Mobility Particle Sizer (SMPS). Dieses Messgerät zeigte in Präsenz von Nanopartikel Agglorneraten unsinnige bimodale Partikelgrössenverteilung an. Eine Serie von kurzen Experimenten folgte, welche sich auf andere Messgeräte und deren Probleme beim Messen von Nanopartikel-Agglomeraten konzentrierten. Der Condensation Particle Counter (CPC), der portable aerosol spectrometer (PAS), ein Gerät zur Schàtzung des aerodynamischen Durchniessers von Teilchen, sowie der Diffusion Size Classifier wurden getestet. Einige erste Machbarkeitstests zur Ermittlnng der Effizienz von tilterbasierter Messung von luftgetragenen Carbon Nanotubes (CNT) wnrden als letztes durchgeiührt. Die Pilotstudie hat ein detailliiertes Bild der Typen und Mengen von genutzten Nanopartikel in Schweizer Unternehmen geliefert, und hat den Stand des Wissens der interviewten Gesundheitsschntz und Sicherheitsfachleute aufgezeigt. Folgende Typen von Nanopaitikeln wurden von den kontaktierten Firmen als Maximalmengen angegeben (> 1'000 kg pro Jahr / Unternehrnen): Ag, Al-Ox, Fe-Ox, SiO2, TiO2, und ZnO (hauptsächlich Nanopartikel der ersten Generation). Die Quantitäten von eingesetzten Nanopartikeln waren stark verschieden mit einem ein Median von 100 kg pro Jahr. ln der quantitativen Fragebogenstudie wurden l'626 Unternehmen brieflich kontaktiert; allesamt Klienten der Schweizerischen Unfallversicherringsanstalt (SUVA). Die Resultate der Umfrage erlaubten eine Abschätzung der Anzahl von Unternehmen und Arbeiter, welche Nanopartikel in der Schweiz anwenden. Die Hochrechnung auf den Schweizer lndnstriesektor hat folgendes Bild ergeben: ln 586 Unternehmen (95% Vertrauensintervallz 145 bis 1'027 Unternehmen) sind 1'309 Arbeiter potentiell gegenüber Nanopartikel exponiert (95%-Vl: l'073 bis l'545). Diese Zahlen stehen für 0.6% der Schweizer Unternehmen (95%-Vl: 0.2% bis 1.1%) und 0.08% der Arbeiternehmerschaft (95%-V1: 0.06% bis 0.09%). Es gibt einige gut etablierte Technologien um die Luftkonzentration von Submikrometerpartikel zu messen. Es besteht jedoch Zweifel daran, inwiefern sich diese Technologien auch für die Messurrg von künstlich hergestellten Nanopartikeln verwenden lassen. Aus diesem Grund folcussierten die vorbereitenden Studien für die Arbeitsplatzbeurteilnngen auf die Messung von Pulverri, welche Nan0partike1-Agg10merate enthalten. Sie erlaubten die ldentifikation folgender rnöglicher Quellen von fehlerhaften Messungen an Arbeitsplätzen mit erhöhter Luft-K0nzentrati0n von Nanopartikel Agglomeratenz - Ein Standard SMPS zeigte eine unglaubwürdige bimodale Partikelgrössenverteilung wenn er grössere Nan0par'til<e1Agg10merate gemessen hat. - Grosse Unterschiede im Bereich von Faktor tausend wurden festgestellt zwischen einem Diffusion Size Classiîier und einigen CPC (beziehungsweise dem SMPS). - Die Unterschiede zwischen CPC/SMPS und dem PAS waren geringer, aber abhängig von Grosse oder Typ des gemessenen Pulvers waren sie dennoch in der Grössenordnung von einer guten Grössenordnung. - Spezifische Schwierigkeiten und Unsicherheiten im Bereich von Arbeitsplatzmessungen wurden identitiziert: Hintergrundpartikel können mit Partikeln interagieren die während einem Arbeitsprozess freigesetzt werden. Solche Interaktionen erschweren eine korrekte Einbettung der Hintergrunds-Partikel-Konzentration in die Messdaten. - Elektromotoren produzieren grosse Mengen von Nanopartikeln und können so die Messung der prozessbezogenen Exposition stören. Fazit: Die Umfragen zeigten, dass Nanopartikel bereits Realitàt sind in der Schweizer Industrie und dass einige Unternehmen bereits grosse Mengen davon einsetzen. Die repräsentative Umfrage hat diese explosive Nachricht jedoch etwas moderiert, indem sie aufgezeigt hat, dass die Zahl der Unternehmen in der gesamtschweizerischen Industrie relativ gering ist. In den meisten Branchen (vor allem ausserhalb der Chemischen Industrie) wurden wenig oder keine Anwendungen gefunden, was schliessen last, dass die Einführung dieser neuen Technologie erst am Anfang einer Entwicklung steht. Auch wenn die Zahl der potentiell exponierten Arbeiter immer noch relativ gering ist, so unterstreicht die Studie dennoch die Notwendigkeit von Expositionsmessungen an diesen Arbeitsplätzen. Kenntnisse um die Exposition und das Wissen, wie solche Exposition korrekt zu messen, sind sehr wichtig, vor allem weil die möglichen Auswirkungen auf die Gesundheit noch nicht völlig verstanden sind. Die Evaluation einiger Geräte und Methoden zeigte jedoch, dass hier noch Nachholbedarf herrscht. Bevor grössere Mess-Studien durgefîihrt werden können, müssen die Geräte und Methodem für den Einsatz mit Nanopartikel-Agglomeraten validiert werden.

An ultra-sensitive impedimetric immunosensor for detection of the serum oncomarker CA-125 in ovarian cancer patients.

Effective treatment of ovarian cancer depends upon the early detection of the malignancy. Here, we report on the development of a new nanostructured immunosensor for early detection of cancer antigen 125 (CA-125). A gold electrode was modified with mercaptopropionic acid (MPA), and then consecutively conjugated with silica coated gold nanoparticles (AuNP@SiO2), CdSe quantum dots (QDs) and anti-CA-125 monoclonal antibody (mAb). The engineered MPA|AuNP@SiO2|QD|mAb immunosensor was characterised using transmission electron microscopy (TEM), atomic force microscopy (AFM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Successive conjugation of AuNP@SiO2, CdSe QD and anti-CA-125 mAb onto the gold electrode resulted in sensitive detection of CA-125 with a limit of detection (LOD) of 0.0016 U mL(-1) and a linear detection range (LDR) of 0-0.1 U mL(-1). Based on the high sensitivity and specificity of the immunosensor, we propose this highly stable and reproducible biosensor for the early detection of CA-125.

Paragênese mineral de solos desenvolvidos de diferentes litologias na região sul de Minas Gerais

Estudos sistemáticos sobre os fatores de formação do solo são relativamente escassos no Brasil, em razão da dificuldade de amostrar vários níveis de um fator, mantendo os demais constantes. A região de Lavras, MG, possui grande diversidade geológica em uma área pequena, o que possibilita avaliar o controle exercido por diferentes litologias na mineralogia e nas demais características do solo. Foram selecionados oito solos embasados sobre quartzito, mica-xisto, gabro, itabirito, serpentinito, metacalcário, gnaisse e filito, em condições semelhantes de vegetação (floresta tropical semidecidual), relevo (terço médio de encosta) e clima. Após a descrição dos perfis, coletaram-se amostras dos horizontes e das rochas, e realizaram-se análises físicas e químicas de rotina, composição química total e mineralogia da rocha, da areia e da argila do solo. Todos os solos são pobres em bases trocáveis (exceto o Argissolo sobre itabirito), e notou-se grande variação na composição granulométrica, mineralógica e química. Os teores de Al2O3, SiO2 e Fe2O3 presentes nas rochas não evidenciaram correlação com os respectivos teores nos solos derivados, enquanto o teor de Fe2O3 foi fortemente correlacionado à densidade de partículas e suscetibilidade magnética. Apesar de evidências de material parcialmente alóctone em alguns casos, pôde-se notar forte influência da litologia subjacente na paragênese mineralógica. Os solos foram genericamente agrupados em: cauliníticos com minerais 2:1 (Argissolos sobre mica-xisto e itabirito; e Cambissolo sobre quartzito), cauliníticos (Argissolos sobre gnaisse e filito) e oxídicos (Latossolos sobre metacalcário e gabro; e Plintossolo sobre serpentinito). Os processos de monossialitização e alitização predominam na região, sendo respectivamente associados a rochas com valores intermediários e baixos em sílica, enquanto a presença de minerais 2:1 é acessória à caulinita e parece depender da presença de mica e altos teores de sílica na rocha de origem.

Pedogênese e classificação de latossolos desenvolvidos de itabiritos no Quadrilátero Ferrífero, MG

Localizado na porção centro-oeste do Estado de Minas Gerais, o Quadrilátero Ferrífero abrange uma área de aproximadamente 7.000 km². Desde o século XVII, a região é conhecida como uma província aurífera e ferrífera, sendo por essa razão uma das regiões mais bem estudadas do Brasil no contexto geológico. A região é de topografia muito acidentada, onde predominam solos pouco evoluídos pedogeneticamente, com destaque para Cambissolos Háplicos, Neossolos Litólicos e Neossolos Regolíticos. Em menor proporção e em rampas de colúvio (relevo suave ondulado), ocorrem Latossolos Vermelhos muito ricos em Fe, anteriormente denominados Latossolos Ferríferos. Neste trabalho, foram realizados estudos para caracterizar física, química e mineralogicamente amostras de nove perfis de Latossolos Vermelhos férricos e perférricos, desenvolvidos de itabirito e rochas afins no Quadrilátero Ferrífero, com os objetivos de melhor entender sua gênese e avaliar critérios taxonômicos que permitam sua diferenciação no SiBCS, em níveis categóricos mais baixos. Os elevados valores de densidade de partículas são peculiares nesses solos e, ao lado da estrutura forte, muito pequena e granular, são fatores que contribuem para subestimar os teores de argila e superestimar os de silte, resultando em relação silte/argila maior do que aquela proposta pelo SiBCS para os Latossolos. A variação dos teores de SiO2, Fe2O3, Al2O3, TiO2, MnO, P2O5 e de alguns elementos-traço aponta para a diversidade na composição química do itabirito ou, ainda, provável mistura com rochas filíticas da região. Os valores das relações Fe2O3/TiO2 (não molecular) e TiO2/Fe2O3 (molecular) revelaram-se diferentes daqueles sugeridos na literatura para separação de Latossolos Vermelhos desenvolvidos de itabirito daqueles de rochas máficas. As frações areia, silte e argila apresentaram grande variação na atração magnética, com as duas primeiras frações evidenciando maior magnetização, em razão da presença de magnetita. Os valores de substituição isomórfica de Fe por Al variaram 0,07 a 0,11 e 0,09 a 0,38 mol mol-1 nas estruturas da hematita e magnetita, respectivamente.

Geoquímica de solos do pantanal norte, Mato Grosso

A caracterização e análise geoquímica de solos permitem compreender os processos de migração, dispersão e concentração de elementos químicos no perfil, embasando a correlação dos atributos deles com as classes de solos formadas, o que possibilita inferências acerca das gêneses desses solos. Esta pesquisa teve por objetivos caracterizar e interpretar a composição geoquímica total de elementos maiores e menores em classes de solos representativas do Pantanal norte, na sub-região de Barão de Melgaço, Mato Grosso, Brasil. Foram selecionados 20 perfis das principais classes de solos do Pantanal e analisadas amostras dos horizontes A e B (ou C) quanto à concentração de óxidos totais por espectrometria de fluorescência de raios-X, além das caracterizações física, química e mineralógica. Os solos subdividiram-se em dois tipos geoquímicos: um composto por textura arenosa a franco-arenosa com teores relativamente elevados de SiO2 e predominância de caulinita e quartzo, com menor teor de bases e elementos-traço; e outro composto por textura mais argilosa, geoquimicamente heterogêneos e com teores significativos de minerais 2:1, Al2O3, óxidos de Fe e Mn, bases e elementos-traço.

SPATIAL VARIABILITY OF SOIL PROPERTIES IN AN AGRARIAN REFORM SETTLEMENT

ABSTRACT The study of soil chemical and physical properties variability is important for suitable management practices. The aim of this study was to evaluate the spatial variability of soil properties in the Malhada do Meio settlement to subsidize soil use planning. The settlement is located in Chapadinha, MA, Brazil, and has an area of 630.86 ha. The vegetation is seasonal submontane deciduous forest and steppe savanna. The geology is formed of sandstones and siltstones of theItapecuru Formation and by colluvial and alluvial deposits. The relief consists of hills with rounded and flat tops with an average altitude of 67 m, and frequently covered over by ferruginous duricrusts. A total of 183 georeferenced soil samples were collected at the depth of 0.00-0.20 m inPlintossolos, Neossolo andGleissolo. The following chemical variables were analyzed: pH(CaCl2), H+Al, Al, SB, V, CEC, P, K, OM, Ca, Mg, SiO2, Al2O3, and Fe2O3; along with particle size variables: clay, silt, and sand. Descriptive statistical and geostatistical analyses were carried out. The coefficient of variation (CV) was high for most of the variables, with the exception of pH with a low CV, and of sand with a medium CV. The models fitted to the experimental semivariograms of these variables were the exponential and the spherical. The range values were from 999 m to 3,690 m. For the variables pH(CaCl2), SB, and clay, there are three specific areas for land use planning. The central part of the area (zone III), where thePlintossolos Pétricos and Neossolos Flúvicos occur, is the most suitable for crops due to higher macronutrient content, organic matter and pH. Zones I and II are indicated for environmental preservation.

Use of nanoparticles in Swiss industry: a targeted survey

A large number of applications using manufactured nanoparticles of less than 100 nm are currently being introduced into industrial processes. There is an urgent need to evaluate the risks of these novel particles to ensure their safe production, handling, use, and disposal. However, today we lack even rudimentary knowledge about type and quantity of industrially used manufactured nanoparticles and the level of exposure in Swiss industry. The goal of this study was to evaluate the use of nanoparticles, the currently implemented safety measures, and the number of potentially exposed workers in all types of industry. To evaluate this, a targeted telephone survey was conducted among health and safety representatives from 197 Swiss companies. The survey showed that nanoparticles are already used in many industrial sectors; not only in companies in the new field of nanotechnology, but also in more traditional sectors, such as paints. Forty-three companies declared to use or produce nanoparticles, and 11 imported and traded with prepackaged goods that contain nanoparticles. The following nanoparticles were found to be used in considerable quantities (> 1000 kg/year per company): Ag, Al-Ox, Fe-Ox, SiO2, TiO2, and ZnO. The median reported quantity of handled nanoparticles was 100 kg/year. The production of cosmetics, food, paints, powders, and the treatment of surfaces used the largest quantities of these nanoparticles. Generally, the safety measures were found to be higher in powder-based than in liquid-based applications. However, the respondents had many open questions about best practices, which points to the need for rapid development of guidelines and protection strategies

Efeito da força iônica da solução de equilíbrio sobre a adsorção/dessorção de chumbo em Latossolos brasileiros

A adsorção/dessorção de metais pelos solos é afetada por vários fatores, dentre os quais, a concentração salina da solução do solo. Este estudo teve o objetivo de avaliar o efeito da variação da força iônica da solução de equilíbrio (I) sobre a adsorção/dessorção de Pb por Latossolos brasileiros. Amostras do horizonte A foram colocadas para reagir com Pb(NO3)2 0,15 mmol L-1 em Ca(NO3)2 5 e 50 mmol L-1 (pH 5,5; I = 15 e 150 mmol L-1; relação solo:solução 1:100), durante 72 horas. Em seguida, as amostras foram colocadas para dessorver em Ca(NO3)2 5 mmol L-1. Dos 17 Latossolos, apenas seis apresentaram diferenças significativas entre as quantidades adsorvidas nos dois valores de I. As correlações significativas obtidas entre as quantidades adsorvidas e alguns atributos dos solos (SiO2 e Fe2O3 do ataque sulfúrico, Fe d e Fe o, caulinita, hematita, CTC e superfície específica) foram as mesmas para os dois valores de I. A variação de I durante a adsorção teve pouco efeito sobre a dessorção de chumbo. A não-variação da quantidade adsorvida com a mudança de I indica que o Pb é adsorvido, na maioria dos Latossolos, como complexo de esfera interna. Conclui-se que, dentro destas condições experimentais, o Pb não fez parte do complexo de troca da maioria dos solos estudados.

Comment on “Dynamics of thermal growth of silicon oxide films on Si”

The paper commented on here R. M. C. de Almeida, S. Gonçalves, I. J. R. Baumvol and F. C. Stedile Phys. Rev. B 61 12992 (2000) claims that the Deal and Grove model of oxidation is unable to describe the kinetics in the thin oxide regime due to two main simplifications: (a) the steady-state assumption and (b) the abrupt Si∕SiO2 interface assumption. Although reasonably good fits are obtained without these simplifications, it will be shown that the values of the kinetic parameters are not reliable and that the solutions given for different partial pressures are erroneous. Finally, it will be shown that the correct solution of their model is unable to predict the oxidation rate enhancement observed in the thin oxide regime and that the predicted width of the interface compatible with the Deal and Grove rate constants is too large