Road Design for Future Maintenance : Life-cycle Cost Analyses for Road Barriers

The cost of a road construction over its service life is a function of design, quality of construction as well as maintenance strategies and operations. An optimal life-cycle cost for a road requires evaluations of the above mentioned components. Unfortunately, road designers often neglect a very important aspect, namely, the possibility to perform future maintenance activities. Focus is mainly directed towards other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This doctoral thesis presents the results of a research project aimed to increase consideration of road maintenance aspects in the planning and design process. The following subgoals were established: Identify the obstacles that prevent adequate consideration of future maintenance during the road planning and design process; and Examine optimisation of life-cycle costs as an approach towards increased efficiency during the road planning and design process. The research project started with a literature review aimed at evaluating the extent to which maintenance aspects are considered during road planning and design as an improvement potential for maintenance efficiency. Efforts made by road authorities to increase efficiency, especially maintenance efficiency, were evaluated. The results indicated that all the evaluated efforts had one thing in common, namely ignorance of the interrelationship between geometrical road design and maintenance as an effective tool to increase maintenance efficiency. Focus has mainly been on improving operating practises and maintenance procedures. This fact might also explain why some efforts to increase maintenance efficiency have been less successful. An investigation was conducted to identify the problems and difficulties, which obstruct due consideration of maintainability during the road planning and design process. A method called “Change Analysis” was used to analyse data collected during interviews with experts in road design and maintenance. The study indicated a complex combination of problems which result in inadequate consideration of maintenance aspects when planning and designing roads. The identified problems were classified into six categories: insufficient consulting, insufficient knowledge, regulations and specifications without consideration of maintenance aspects, insufficient planning and design activities, inadequate organisation and demands from other authorities. Several urgent needs for changes to eliminate these problems were identified. One of the problems identified in the above mentioned study as an obstacle for due consideration of maintenance aspects during road design was the absence of a model for calculating life-cycle costs for roads. Because of this lack of knowledge, the research project focused on implementing a new approach for calculating and analysing life-cycle costs for roads with emphasis on the relationship between road design and road maintainability. Road barriers were chosen as an example. The ambition is to develop this approach to cover other road components at a later stage. A study was conducted to quantify repair rates for barriers and associated repair costs as one of the major maintenance costs for road barriers. A method called “Case Study Research Method” was used to analyse the effect of several factors on barrier repairs costs, such as barrier type, road type, posted speed and seasonal effect. The analyses were based on documented data associated with 1625 repairs conducted in four different geographical regions in Sweden during 2006. A model for calculation of average repair costs per vehicle kilometres was created. Significant differences in the barrier repair costs were found between the studied barrier types. In another study, the injuries associated with road barrier collisions and the corresponding influencing factors were analysed. The analyses in this study were based on documented data from actual barrier collisions between 2005 and 2008 in Sweden. The result was used to calculate the cost for injuries associated with barrier collisions as a part of the socio-economic cost for road barriers. The results showed significant differences in the number of injuries associated with collisions with different barrier types. To calculate and analyse life-cycle costs for road barriers a new approach was developed based on a method called “Activity-based Life-cycle Costing”. By modelling uncertainties, the presented approach gives a possibility to identify and analyse factors crucial for optimising life-cycle costs. The study showed a great potential to increase road maintenance efficiency through road design. It also showed that road components with low investment costs might not be the best choice when including maintenance and socio-economic aspects. The difficulties and problems faced during the collection of data for calculating life-cycle costs for road barriers indicated a great need for improving current data collecting and archiving procedures. The research focused on Swedish road planning and design. However, the conclusions can be applied to other Nordic countries, where weather conditions and road design practices are similar. The general methodological approaches used in this research project may be applied also to other studies.

Using system dynamics for collaborative design : a case study

Background  In order to facilitate the collaborative design, system dynamics (SD) with a group modelling approach was used in the early stages of planning a new stroke unit. During six workshops a SD model was created in a multiprofessional group. Aim To explore to which extent and how the use of system dynamics contributed to the collaborative design process. Method A case study was conducted using several data sources. Results SD supported a collaborative design, by facilitating an explicit description of stroke care process, a dialogue and a joint understanding. The construction of the model obliged the group to conceptualise the stroke care and experimentation with the model gave the opportunity to reflect on care. Conclusion SD facilitated the collaborative design process and should be integrated in the early stages of the design process as a quality improvement tool.

Shared-decision making in designing new healthcare environments : ready to take off for improved quality

Background Successful implementation of new methods and models of healthcare to achieve better patient outcomes and safe, person-centered care is dependent on the physical environment of the healthcare architecture in which the healthcare is provided. Thus, decisions concerning healthcare architecture are critical because it affects people and work processes for many years and requires a long-term financial commitment from society. In this paper, we describe and suggest several strategies (critical factors) to promote shared-decision making when planning and designing new healthcare environments. Discussion This paper discusses challenges and hindrances observed in the literature and from the authors extensive experiences in the field of planning and designing healthcare environments. An overview is presented of the challenges and new approaches for a process that involves the mutual exchange of knowledge among various stakeholders. Additionally, design approaches that balance the influence of specific and local requirements with general knowledge and evidence that should be encouraged are discussed. Summary We suggest a shared-decision making and collaborative planning and design process between representatives from healthcare, construction sector and architecture based on evidence and end-users’ perspectives. If carefully and systematically applied, this approach will support and develop a framework for creating high quality healthcare environments.

Evaluating And Optimizing Sustainable Drainage Design To Maximize Multiple Benefits: Case Studies In China

In the past, the focus of drainage design was on sizing pipes and storages in order to provide sufficient network capacity. This traditional approach, together with computer software and technical guidance, had been successful for many years. However, due to rapid population growth and urbanisation, the requirements of a “good” drainage design have also changed significantly. In addition to water management, other aspects such as environmental impacts, amenity values and carbon footprint have to be considered during the design process. Going forward, we need to address the key sustainability issues carefully and practically. The key challenge of moving from simple objectives (e.g. capacity and costs) to complicated objectives (e.g. capacity, flood risk, environment, amenity etc) is the difficulty to strike a balance between various objectives and to justify potential benefits and compromises. In order to assist decision makers, we developed a new decision support system for drainage design. The system consists of two main components – a multi-criteria evaluation framework for drainage systems and a multi-objective optimisation tool. The evaluation framework is used for the quantification of performance, life-cycle costs and benefits of different drainage systems. The optimisation tool can search for feasible combinations of design parameters such as the sizes, order and type of drainage components that maximise multiple benefits. In this paper, we will discuss real-world application of the decision support system. A number of case studies have been developed based on recent drainage projects in China. We will use the case studies to illustrate how the evaluation framework highlights and compares the pros and cons of various design options. We will also discuss how the design parameters can be optimised based on the preferences of decision makers. The work described here is the output of an EngD project funded by EPSRC and XP Solutions.

Agências reguladoras independentes?: especialização e captura nas trajetórias de carreira dos reguladores federais brasileiros

Este trabalho analisa o perfil e as trajetórias de carreira dos diretores e conselheiros das se-guintes agências federais: ANEEL, ANATEL, ANP, ANVISA, ANS, ANA, ANCINE, AN-TAQ, ANTT e ANAC. São observadas algumas dimensões que se relacionam com condicio-nantes que, em tese, permitiriam uma maior autonomia decisória do regulador brasileiro federal: 1) o nível de expertise e conhecimento especializado do regulador, observando sua área de formação, nível de escolaridade e sua experiência prévia no setor regulado; 2) a existência ou não de filiação partidária antes de sua indicação para o cargo na agência; 3) a existência ou não de casos de recondução de reguladores, além dos mandados governamentais de diferentes presidentes; e 4) a origem e o destino profissional do regulador após sua atuação na agência reguladora. Paralelamente, observa-se como foi elaborado o desenho institucional destas agências brasileiras e como algumas características de sua estrutura e processo podem interferir com o resultado do processo regulatório, especialmente no que se refere à forma como os reguladores são indicados. Entre os principais resultados do trabalho, destacam-se a forte co-nexão entre a área de formação dos reguladores e o campo de atuação das agências reguladores; a valorização de cursos de pós-graduação na qualificação de um candidato para uma agência reguladora federal; e a comprovação de experiência profissional prévia no setor regulado, indicando que os reguladores brasileiros apresentam indicadores relevantes de especialização e expertise no setor. Também ocorreram casos de reguladores indicados e reconduzidos por presidentes diferentes, reforçando a hipótese de valorização da especialização. Com relação a captura política, se destaca que pouco menos de um terço dos indicados possuía filiação partidária anterior à nomeação. A maioria dos reguladores é selecionada dentro do serviço público, mas boa parte deles vai trabalhar na esfera privada do setor, reforçando os indícios de que pode ter havido captura durante os mandatos na agência. Percebe-se, ainda, uma forte tendência de fortalecimento da burocracia das agências a partir do final do primeiro mandato do presidente Lula, movimento acentuado no primeiro mandato da presidente Dilma Rousseff.

Design e management: um estudo de ciência e tecnologia no campo dos estudos organizacionais

Esta dissertação se propõe a cartografar as redes sociotécnicas do design no campo do management nos moldes propostos pela Teoria Ator-Rede e apresentar o processo de translação pelo qual passou o termo ao adentrar no campo. Para tal, levantou e analisou artigos publicados sobre o tema nos principais periódicos da área de organizações e publicações. Estes textos demonstram como, nas últimas décadas, o design tem passado por uma expansão de sentido e aplicação na direção do management (ou do management no sentido do design), através das abordagens denominadas design thinking, design science ou design process. A pesquisa se justifica, uma vez que este assunto está presente nos principais periódicos do management e dos estudos organizacionais, como uma importante ferramenta para solução de problemas que desafiam os sistemas organizacionais, como: a mudança, o empreendedorismo e a inovação (Stephens & Boland, 2014). É importante destacar que o design tem sido cada vez mais considerado uma atividade decisiva na batalha econômica (Callon, 1986), na determinação dos atuais estilos de vida (lifestyle) e na construção de nosso mundo futuro. No campo dos estudos organizacionais, como demonstrou esta pesquisa, o design surge como uma abordagem que supera a dicotomia entre positivismo e a abordagem crítica na teoria organizacional (Jelinek, Romme & Boland, 2008). Por fim, esta dissertação se ateve à cartografia das redes sociotécnicas e à descrição das quatro principais fases do processo de translação do design no campo do management, a saber: (a) problematização, marcada pela publicação de The Sciences of Artificial em 1969 de Herbert A. Simon, no qual, ele argumenta pelo design como uma habilidade básica para todas as especialidades profissionais, incluindo a gestão (Simon, 1996), (b) interessamento, designers defendendo um design de sistemas complexos como as organizações, (c) engajamento, designers e teóricos das organizações juntos pelo design no management como uma alternativa para a superação da dicotomia entre positivismo e os estudos críticos na administração, e, (d) mobilização, na qual os teóricos das organizações partem em defesa do design no management como um forma de dar conta de modelos organizacionais contemporâneos com fronteiras mais permeáveis e em constante reformulação

Modos projetuais de simulação: uso de ferramentas de simulação térmica no processo projetual de arquitetura

This thesis aims to describe and demonstrate the developed concept to facilitate the use of thermal simulation tools during the building design process. Despite the impact of architectural elements on the performance of buildings, some influential decisions are frequently based solely on qualitative information. Even though such design support is adequate for most decisions, the designer will eventually have doubts concerning the performance of some design decisions. These situations will require some kind of additional knowledge to be properly approached. The concept of designerly ways of simulating focuses on the formulation and solution of design dilemmas, which are doubts about the design that cannot be fully understood nor solved without using quantitative information. The concept intends to combine the power of analysis from computer simulation tools with the capacity of synthesis from architects. Three types of simulation tools are considered: solar analysis, thermal/energy simulation and CFD. Design dilemmas are formulated and framed according to the architect s reflection process about performance aspects. Throughout the thesis, the problem is investigated in three fields: professional, technical and theoretical fields. This approach on distinct parts of the problem aimed to i) characterize different professional categories with regards to their design practice and use of tools, ii) investigate preceding researchers on the use of simulation tools and iii) draw analogies between the proposed concept, and some concepts developed or described in previous works about design theory. The proposed concept was tested in eight design dilemmas extracted from three case studies in the Netherlands. The three investigated processes are houses designed by Dutch architectural firms. Relevant information and criteria from each case study were obtained through interviews and conversations with the involved architects. The practical application, despite its success in the research context, allowed the identification of some applicability limitations of the concept, concerning the architects need to have technical knowledge and the actual evolution stage of simulation tools

Do modelo geométrico ao modelo físico: o tridimensional na educação do arquiteto e urbanista

In the teaching practice of architecture and urbanism in Brazil, educational legislation views modeling laboratories and workshops as an indispensable component of the infrastructure required for the good functioning of any architectural course of study. Although the development of information technology at the international level has created new possibilities for digital production of architectural models, research in this field being underway since the early 1990s, it is only from 2007 onwards that such technologies started to be incorporated into the teaching activity of architecture and urbanism in Brazil, through the pioneering experience at LAPAC/FEC/UNICAMP. It is therefore a recent experiment whose challenges can be highlighted through the following examples: (i) The implementation of digital prototyping laboratories in undergraduate courses of architecture and urbanism is still rare in Brazil; (ii) As a new developing field with few references and application to undergraduate programs, it is hard to define methodological procedures suitable for the pedagogical curricula already implemented or which have already been consolidated over the years; (iii) The new digital ways for producing tridimensional models are marked with specificities which make it difficult to fit them within the existing structures of model laboratories and workshops. Considering the above, the present thesis discusses the tridimensional model as a tool which may contribute to the development of students skills in perceiving, understanding and representing tridimensional space. Analysis is made of the relation between different forms of models and the teaching of architectural project, with emphasis on the design process. Starting from the conceptualization of the word model as it is used in architecture and urbanism, an attempt is made to identify types of tridimensional models used in the process of project conception, both through the traditional, manual way of model construction as well as through the digital ones. There is also an explanation on how new technologies for digital production of models through prototyping are being introduced in undergraduate academic programs of architecture and urbanism in Brazil, as well as a review of recent academic publications in this area. Based on the paradigm of reflective practice in teaching as designed by Schön (2000), the experiment applied in the research was undertaken in the integrated workshop courses of architectural project in the undergraduate program of architecture and urbanism at Universidade Federal do Rio Grande do Norte. Along the experiment, physical modeling, geometric modeling and digital prototyping are used in distinct moments of the design process with the purpose of observing the suitability of each model to the project s phases. The procedures used in the experiments are very close to the Action Research methodology in which the main purpose is the production of theoretical knowledge by improving the practice. The process was repeated during three consecutive semesters and reflection on the results which were achieved in each cycle helped enhancing the next one. As a result, a methodological procedure is proposed which consists of the definition of the Tridimensional Model as the integrating element for the contents studied in a specific academic period or semester. The teaching of Architectural Project as it is developed along the fifth academic period of the Architecture and Urbanism undergraduate program of UFRN is taken as a reference

Todo Brasileiro merece nível A : habitação multifamiliar para o programa minha casa minha vida energeticamente eficiente

This thesis describes the theoretical, methodological and programmatic proposal for a multifamily residential building located in the urban expansion area of Parnamirim/RN, inserted in the program Minha Casa Minha Vida and level of energy efficiency "A", as the RegulamentoTécnico de Qualidade (RTQ-R/INMETRO) for residential buildings. The development project initially consists of procedures as the study of theoretical, architectural programming and cases studies. With the delimitation of a field solution, situated between the reference and the context, proposals are studied to determine the solution and architectural detailing of the proposal. The architectural program was built based on the method of Problem Seeking (Peña and Parshall, 2001) and research has highlighted aspects of reducing the environmental impact and of the program Minha Casa Minha Vida , among others. The design process was characterized by the incorporation of aspects reviewed and programmed, seeking them compatible and have an economically viable building, socio-spatial quality and energy efficient. The results show that it is possible to obtain a building that meets the constraints of the program that provides housing and energy efficiency level A - and many other environmental qualities and constructive, particularly through architectural design

GRIOT - sistema CAD inteligente para design de calçados

O presente trabalho é o estudo dos aspectos da metodologia projetual, face às novas tecnologias da informática, Inteligência Artificial (Sistemas Especialistas) e CAD, consideradas as reais possibilidades de automatização no processo de concepção em Design. Esse artigo propõe uma metodologia para a construção de sistema inteligente capaz de auxiliar o designer nas tarefas projetuais. A indústria de calçados foi utilizada como estudo de caso para a aplicação da metodologia, onde as reais possibilidades de automação são verificadas.

Comparative analysis between a CAD model design and physical models obtained by manufacturing additive technologies using optical scan

This article presents a detailed study of the application of different additive manufacturing technologies (sintering process, three-dimensional printing, extrusion and stereolithographic process), in the design process of a complex geometry model and its moving parts. The fabrication sequence was evaluated in terms of pre-processing conditions (model generation and model STL SLI), generation strategy and physical model post-processing operations. Dimensional verification of the obtained models was undertook by projecting structured light (optical scan), a relatively new technology of main importance for metrology and reverse engineering. Studies were done in certain manufacturing time and production costs, which allowed the definition of an more comprehensive evaluation matrix of additive technologies.

Fatores associados à efetividade da doação de órgãos e tecidos para transplantes

The transplantation of organs and tissues presents itself as an important therapeutic option, both from a medical standpoint, the social or economic. Thus, the identification of variables that can interfere in the effectiveness of organs and tissues donation for transplantation needs to be investigated adequately, because it stands before increasing index of chronic and degenerative diseases in the population, what makes the waiting list for transplantation grow disproportionately and patients come to death without the opportunity of realization the treatment due to a lack of donors. In this context, has defined as objective of this study evaluate the factors associated with the effectiveness of organs and tissues donation for transplantation. It is a evaluative research, quantitative, prospective, with longitudinal design, developed at Central of Catchment, Notification and organ donation for transplant, Organ Procurement Organization and in six accredited hospitals to collect and transplantation of organs and tissues, in Natal/RN, between august 2010 and february 2011, after the approval of the Research Ethics Committee, under No. 414/10 and CAAE 007.0.294.000-10. The probabilistic sample without replacement was composed of 65 potential donors. It was used as an instrument of data collection a structured script non-participant observation of checklist type. Data were analyzed using descriptive statistics and presented in tables, charts, graphs and figures. For this, was used Microsoft Excel 2007 and statistical program SPSS version 20.0. To check the level of significance was chosen by applying the chi-square test (χ2) and Mann Whitney and caselas for less than five, it is considered the Fisher exact test. It was adopted as the significance level p-value <0.05. Among the surveyed it was observed that most of the individuals were male (50,8%), in the age group 45 years (53,8%), mean age of 42,3 years, minimum 5 and maximum 73 years (± 17,32 years). Single / widowers / divorced (56,9%), with up to completed elementary school (60,0%) in the exercise of professional activity (86,2%), catholic (83,1%) and residents in metropolitan region of Natal (52,3%). Was obtained donation effectiveness of 27,7%. There was no statistical significance between structure and effectiveness of the donation, but were observed inadequacies in physical resources (36,9%), materials (30,8%), organizational structure (29,2%) and human resources (18,5%). In the process, the maintenance phase (p= 0.004), diagnosis of brain death (p= 0.032), family interview (p≤ 0.001) and documentation (p= 0.001) presented statistical significance with effectiveness. Thus, it is accepts the alternative hypothesis of the study, in which is evidenced that the adequacy of the factors related to structure and process is associated to effectiveness of organs and tissues donation for transplantation. In this way, the effectiveness of organ and tissue donation ends in an essential way the rapidity and accuracy with which the donation process is conducted, requiring appropriate structure, with appropriate physical and material resources and skilled human resources to optimize the reduction of time and the suffering of those waiting for an organ or tissue transplant queued in Brazil

MARISA-MDD: uma abordagem para transformações entre modelos orientados a aspectos: dos requisitos ao projeto detalhado

Aspect Oriented approaches associated to different activities of the software development process are, in general, independent and their models and artifacts are not aligned and inserted in a coherent process. In the model driven development, the various models and the correspondence between them are rigorously specified. With the integration of aspect oriented software development (DSOA) and model driven development (MDD) it is possible to automatically propagate models from one activity to another, avoiding the loss of information and important decisions established in each activity. This work presents MARISA-MDD, a strategy based on models that integrate aspect-oriented requirements, architecture and detailed design, using the languages AOV-graph, AspectualACME and aSideML, respectively. MARISA-MDD defines, for each activity, representative models (and corresponding metamodels) and a number of transformations between the models of each language. These transformations have been specified and implemented in ATL (Atlas Definition Language), in the Eclipse environment. MARISA-MDD allows the automatic propagation between AOV-graph, AspectualACME, and aSideML models. To validate the proposed approach two case studies, the Health Watcher and the Mobile Media have been used in the MARISA-MDD environment for the automatic generation of AspectualACME and aSideML models, from the AOV-graph model