Organization dependent collective magnetic properties of secondary nanostructures with differential spatial ordering and magnetic easy axis orientation

Achieving control on the formation of different organization states of magnetic nanoparticles is crucial to harness their organization dependent physical properties in desired ways. In this study, three organization states of iron oxide nanoparticles (gamma-Fe2O3), defining as (i) assembly (ii) network aggregate and (iii) cluster, have been developed by simply changing the solvent evaporation conditions. All three systems have retained the same phase and polydispersity of primary particles. Magnetic measurements show that the partial alignment of the easy axes of the particles in the network system due to the stacking aggregation morphology can result in significant enhancement of the coercivity and remanence values, while the opposite is obtained for the cluster system due to the random orientation of easy axes. Partial alignment in the aggregate system also results in noticeable non -monotonic field dependence of ZFC peak temperature (TpeaB). The lowest value of the blocking temperature (TB) for the cluster system is related to the lowering of the effective anisotropy due to the strongest demagnetizing effect. FC (Field cooled) memory effect was observed to be decreasing with the increasing strength of dipolar interaction of organization states. Therefore, the stacking aggregation and the cluster formation are two interesting ways of magnetic nanoparticles organization for modulating collective magnetic properties significantly, which can have renewed application potentials from recording devices to biomedicine. (C) 2016 Elsevier B.V. All rights reserved.

Distributions of temperature, velocity and viscosity at symmetrical axis of cylindrical plume in earth's mantle with variable viscosity

The parameters at the symmetrical axis of a cylindrical plume characterize the strength of this plume and provide a boundary condition which must be given to investigate the structure of a plume. For Newtonian fluid with a temperature-and pressure-dependence viscosity, an asymptotical solution of hydrodynamic equations at the symmetrical axis of the plume is found in the present paper. The temperature, upward velocity and viscosity at the symmetrical axis have been obtained as functions of depth, The calculated results have been given for two typical sets of Newtonian rheological parameters. The results obtained show that the temperature distribution along the symmetrical axis is nearly independent of the theological parameters. The upward velocity at the symmetrical axis, however, is strongly dependent on the rheological parameters.

Digitized Processing Track Generation of a Computer Integrated Multi-Functional 5-Axis Laser Processing System

Based on the computer integrated and flexible laser processing system, an intelligent measuring sub-system was developed. A novel model has been built up to compensate the deviations of the main frame-structure, and a new 3-D laser tracker system is applied to adjust the accuracy of the system. To analyze the characteristic of all kind surfaces of automobile outer penal moulds and dies, classification of types of the surface、brim and ridge(or vale) area to be measured and processed has been established, resulting in one of the main processing functions of the laser processing system. According to different type of surfaces, a 2-D adaptive measuring method based on B?zier curve was developed; furthermore a 3-D adaptive measuring method based on Spline curve was also developed. According to the laser materials processing characteristics and data characteristics, necessary methods have been developed to generate processing tracks, they are explained in details. Measuring experiments and laser processing experiments were carried out to testify the above mentioned methods, which have been applied in the computer integrated and flexible laser processing system developed by the Institute of Mechanics, CAS.

Effects of human chorionic gonadotropin (HCG), toad and Clarias pituitary hormogenates on spawning in the catfish: Clarias Lazera (C. and V.) and Clarias anguillaris (Linne)

Experiment on induced spawning of Clarias lazera and C. anguillaris using human chorionic gonadotropin (HCG) freshly prepared toad and Clarias pituitary hormogenates were carried out. Clarias pituitary hormogenates induced spawning in C. lazera and C. anguillaris at dosage levels of 0.27-0.46 mg/150 g body weight or 2 glands/fish of equivalent weights. HCG induced spawning in C. anguillaris at 500 i.u/500 g body weight but failed in C. lazera. Toad pituitary was not successful at even a higher dosage level of 0.60 mg/150 g body weight. The implications of these results are discussed. Spawning occurred in the HCG (and Clarias pituitary treated females in less than 12 hours after injection and subsequent examination of ovaries of the spawned fish showed incomplete spawning. Furthermore, fertilization occurred, following spawning in the piscine pituitary hormone treated male and female fish but failed in the HCG (treated pair. A mean fertilization rate of 50-90% was recorded. Possible explanations of these observations are advanced. The hatching time of 24-48 hours and a mean hatching rate of 75-90% were recorded. A high larval mortality of up to 95% was observed in the post yolk-sac stag after 8 days. The need for the development of appropriate larval food for Clarias species in culture practice is stressed

Induced spawning of African cat fish Clarias lazera (C. and V.) using acetone dried carp pituitary extract, deoxy-corticosterone acetate and human chorionic gonadotropin

A study was conducted to determine the efficacy of carp pituitary extract, deoxycorticosterone acetate, and human chorionic gonadotropin in inducing spawning in Clarias lazera . Results indicate deoxycorticosterone acetate to be more potent than pituitary extract, although the difference is not significant

Utilization of non-piscine pituitary extract in the breeding of Clarias gariepinus

The use of synthetic and non-synthetic hormones have been reported in different regions with the recommendation of different doses. The adaptability of these findings have however not been very successful due to the high cost of building and maintaining hatchery, high cost of synthetic hormone (when available) and high level manpower required. It is obvious that adaptive research in the past ten years in developing countries like Nigeria have been geared towards utilization of resources that are equally effective but cheap and ready to come by. This paper reports the utilization of the pituitary extract of bull frog (Rana adspersa) and the toad (Bufo regularis) in the induced breeding of the African catfish, Clarias gariepinus. The extraction and dosage are discussed alongside the preliminary rearing of fries in outdoor hatchery tanks. Human chorionic gonadotrophin (HCG) and Clarias pituitary extracts were used as control

On the behavior of pliable plate dynamics in wind : application to vertical axis wind turbines

Numerous studies have shown that flexible materials improve resilience and durability of a structure. Several studies have investigated the behavior of elastic plates under the influence of a free stream, such as studies of the fluttering flag and others of shape reconfiguration, due to a free stream.

The principle engineering contribution of this thesis is the design and development of a vertical axis wind turbine that features pliable blades which undergo various modes of behavior, ultimately leading to rotational propulsion of the turbine. The wind turbine design was tested in a wind tunnel and at the Caltech Laboratory for Optimized Wind Energy. Ultimately, the flexible blade vertical axis wind turbine proved to be an effective way of harnessing the power of the wind.

In addition, this body of work builds on the current knowledge of elastic cantilever plates in a free stream flow by investigating the inverted flag. While previous studies have focused on the fluid structure interaction of a free stream on elastic cantilever plates, none had studied the plate configuration where the trailing edge was clamped, leaving the leading edge free to move. Furthermore, the studies presented in this thesis establish the geometric boundaries of where the large-amplitude flapping occurs.