Remoção de óleo da água de produção por flotação em coluna utilizando tensoativos de origem vegetal

In the petroleum industry, water is always present in the reservoir formation together with petroleum and natural gas and this fact provokes the production of water with petroleum, resulting in a great environmental impact. Several methods can be applied for treatment of oily waters, such as: gravitational vases, granulated media filtration systems, flotation process, centrifugation process and the use of hydrocyclones, which can also be used in a combined way. However, the flotation process has showed a great efficiency as compared with other methods, because these methods do not remove great part of the emulsified oil. In this work was investigated the use of surfactants derived from vegetable oils, OSS and OGS, as collectors, using the flotation process in a glass column with a porous plate filter in its base for the input of the gaseous steam. For this purpose, oil/water emulsions were prepared using mechanical stirring, with concentrations around 300 ppm. The air flow rate was set at 700 cm3/min and the porous plate filter used for the generation of the air bubbles has pore size varying from 16 to 40 Pm. The column operated at constant volume (1500mL). A new methodology has been developed to collect the samples, where, instead of collecting the water phase, it was collected the oil phase removed by the process in the top of the flotation column. It has been observed that it is necessary to find an optimum surfactant concentration to achieve enhanced removal efficiency. Being for OSS 1.275 mmol/L and for OGS 0.840 mmol/L, with removal efficiencies of 93% and 99%, respectively, using synthetic solutions. For the produced water, the removal in these concentrations was 75% for OSS and 65% for OGS. It is possible to remove oil from water in a flotation process using surfactants of high HLB, fact that is against the own definition of HLB (Hydrophile-Lipophile Balance). The interfacial tension is an important factor in the oil removal process using a flotation process, because it has direct interference in the coalescence of the oil drops. The spreading of the oil of the air bubble should be considered in the process, and for the optimum surfactant concentrations it reached a maximum value. The removal kinetics for the flotation process using surfactants in the optimum concentration has been adjusted according to a first order model, for synthetic water as for the produced water.

Avaliação da temperatura de cristalização da parafina em sistemas: parafina, solvente e tensoativo

The formation of paraffin deposits is common in the petroleum industry during production, transport and treatment stages. It happens due to modifications in the thermodynamic variables that alter the solubility of alkanes fractions present in petroleum. The deposition of paraffin can provoke significant and growing petroleum losses, arriving to block the flow, hindering to the production. This process is associated with the phases equilibrium L-S and the stages and nucleation, growth and agglomeration the crystals. That process is function of petroleum intrinsic characteristics and temperature and pressure variations, during production. Several preventive and corrective methods are used to control the paraffin crystallization, such as: use of chemical inhibitors, hot solvents injection, use of termochemistry reactions, and mechanical removal. But for offshore exploration this expensive problem needs more investigation. Many studies have been carried through Wax Appearance Temperature (WAT) of paraffin; therefore the formed crystals are responsible for the modification of the reologics properties of the oil, causing a lot off operational problems. From the determination of the WAT of a system it is possible to affirm if oil presents or not trend to the formation of organic deposits, making possible to foresee and to prevent problems of wax crystallization. The solvent n-paraffin has been widely used as fluid of perforation, raising the production costs when it is used in the removal paraffin deposits, needing an operational substitute. This study aims to determine the WAT of paraffin and the interference off additives in its reduction, being developed system paraffin/solvent/surfactant that propitiates the wax solubilization. Crystallization temperatures in varied paraffin concentrations and different solvents were established in the first stage of the experiments. In the second stage, using the methodology of variation of the photoelectric signal had been determined the temperature of crystallization of the systems and evaluated the interferences of additives to reduction of the WAT. The experimental results are expressed in function of the variations of the photoelectric signals during controlled cooling, innovating and validating this new methodology to determine WAT, relatively simple with relation the other applied that involve specific equipments and of high cost. Through the curves you differentiate of the results had been also identified to the critical stages of growth and agglomeration of the crystals that represent to the saturation of the system, indicating difficulties of flow due to the increase of the density

Dimensões geométricas das fibras do músculo sóleo de ratos exercitados em esteira rolante: a importância da análise por meio de imagens digitalizadas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Two-dimensional modeling of material failure in reinforced concrete by means of a continuum strong discontinuity approach

The paper presents a new methodology to model material failure, in two-dimensional reinforced concrete members, using the Continuum Strong Discontinuity Approach (CSDA). The mixture theory is used as the methodological approach to model reinforced concrete as a composite material, constituted by a plain concrete matrix reinforced with two embedded orthogonal long fiber bundles (rebars). Matrix failure is modeled on the basis of a continuum damage model, equipped with strain softening, whereas the rebars effects are modeled by means of phenomenological constitutive models devised to reproduce the axial non-linear behavior, as well as the bondslip and dowel effects. The proposed methodology extends the fundamental ingredients of the standard Strong Discontinuity Approach, and the embedded discontinuity finite element formulations, in homogeneous materials, to matrix/fiber composite materials, as reinforced concrete. The specific aspects of the material failure modeling for those composites are also addressed. A number of available experimental tests are reproduced in order to illustrate the feasibility of the proposed methodology. (c) 2007 Elsevier B.V. All rights reserved.

Comparação dos valores de desgaste abrasivo e de microdureza de 13 resinas compostas usadas em odontologia através do método do disco retificado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermoeconomic analysis method for optimization of combined heat and power systems

This article presents an thermoeconomic analysis of cogeneration plants, applied as a rational technique to produce electric power and saturated steam. The aim of this new methodology is the minimum exergetic manufacturing cost (EMC), based on the Second Law of Thermodynamics. The decision variables selected for the optimization are the pressure and the temperature of the steam leaving the boiler in the case of using steam turbine, and the pressure ratio, turbine exhaust temperature and mass flow in the case of using gas turbines. The equations for calculating the capital costs of the components and products are formulated as a function of these decision variables. An application of the method using real data of a multinational chemical industry located in São Paulo state is presented. The conditions which establish the minimum cost are presented as finals conclusions.

Distribuição diária das atividades comportamentais dos camarões marinhos Farfantepenaeus subtilis (Pérez Farfante, 1967) e Litopenaeus schmitti (Burkenroad, 1938) em condições laboratoriais

Marine aquaculture has developed in the last decades all over the world, especially related to shrimp management. In Brazil, the introduction of the species Litopenaeus vannamei has contributed to the success of the activity, even if there are problems associated with the management of a exotic species, such as new diseases and ecological pressure on native species. It has been emphasized the need of research for developing new methodology that will allow native species management, being the most important Farfantepenaeus subtilis and Litopenaeus schmitti. Most knowledge obtained from research with those species has generally used a technical approach and mainly focused feeding process. There are no specific behavioral data on their activity pattern which should be of great importance for the use of native species on commercial culture farms. So, it was our objective to study and compare the daily distribution of behavioral activities of the marine shrimp species Litopenaeus schmitti and Farfantepenaeus subtilis. Forty animals of each species, 5 individuals per aquarium, were maintained in aquaria containing 200L of sea water under continuous aeration and filtration. They were marked individually and were observed by the instantaneous focal time sampling, along 10 continuous days, in 6 daily 15 min observation windows, every two hour. In each window, behaviors and location position of the animals in the aquarium were registered at 1 min intervals. Food was offered 3 times a day, representing 10% of each aquarium biomass. Aquaria were maintained in artificial photoperiod, 12hour light/l2 hour dark, 4 aquaria in light cycle equivalent to the environmental one (light from 06:00 to 17:59 h and dark from 18:00 to 05:59 h) and the other 4 in the reverse light cycle (light from 18:00 to 05:59 h and dark from 06:00 to 17:59 h) to allow sequential behavioral observation in both phases of the 24 hour cycle. There was a clear distinction between the distribution of behavioral activities of F. subtilis and L. schmitti in the two phases. The activity pattern of Farfantepenaeus subtilis demonstrates that species has prominently night habits and a burying pattern during the light cycle. Exploration, inactivity and swimming were the most common activities. The behavioral pattern of Litopenaeus schmitti indicates that species is active along both phases of the light cycle, and the most evident behaviors were exploration, inactivity and swimming

Setting the preheating and steady-state operation of electronic ballasts, considering electrodes of hot-cathode fluorescent lamps

This paper presents a new methodology for the adjustment of the preheating process and steady-state operation of electronic ballasts intended for hot-cathode fluorescent lamps. The classical series-resonant parallel-loaded half-bridge inverter is the power stage analyzed in this paper. In addition, the preheating process is based on the imposition of a constant rms current through the electrodes, in order to provide a proper value of the R-h/R-c ratio before the lamp start. According to the proposed methodology, it is possible to set suitable operating points for, the electronic ballast, considering optimal conditions for the lamps electrodes. Therefore, the proposed methodology for setting the preheating and steady-state operation is a complete platform to the design of electronic ballasts for hot-cathode fluorescent lamps.

Método da continuação aplicado na análise de contingência de linhas de transmissão

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Técnica de parametrização geométrica para o fluxo de carga continuado baseado nas variáveis tensão nodal e fator de carregamento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Voltammetric studies of titanium (IV) phosphate modified with copper hexacyanoferrate and electroanalytical determination of N-acetylcysteine

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Proposta metodológica para o imageamento, caracterização, parametrização e geração de modelos virtuais de afloramentos

The aim of this work was to describe the methodological procedures that were mandatory to develop a 3D digital imaging of the external and internal geometry of the analogue outcrops from reservoirs and to build a Virtual Outcrop Model (VOM). The imaging process of the external geometry was acquired by using the Laser Scanner, the Geodesic GPS and the Total Station procedures. On the other hand, the imaging of the internal geometry was evaluated by GPR (Ground Penetrating Radar).The produced VOMs were adapted with much more detailed data with addition of the geological data and the gamma ray and permeability profiles. As a model for the use of the methodological procedures used on this work, the adapted VOM, two outcrops, located at the east part of the Parnaiba Basin, were selected. On the first one, rocks from the aeolian deposit of the Piaui Formation (Neo-carboniferous) and tidal flat deposits from the Pedra de Fogo Formation (Permian), which arises in a large outcrops located between Floriano and Teresina (Piauí), are present. The second area, located at the National Park of Sete Cidades, also at the Piauí, presents rocks from the Cabeças Formation deposited in fluvial-deltaic systems during the Late Devonian. From the data of the adapted VOMs it was possible to identify lines, surfaces and 3D geometry, and therefore, quantify the geometry of interest. Among the found parameterization values, a table containing the thickness and width, obtained in canal and lobes deposits at the outcrop Paredão and Biblioteca were the more relevant ones. In fact, this table can be used as an input for stochastic simulation of reservoirs. An example of the direct use of such table and their predicted radargrams was the identification of the bounding surface at the aeolian sites from the Piauí Formation. In spite of such radargrams supply only bi-dimensional data, the acquired lines followed of a mesh profile were used to add a third dimension to the imaging of the internal geometry. This phenomenon appears to be valid for all studied outcrops. As a conclusion, the tool here presented can became a new methodology in which the advantages of the digital imaging acquired from the Laser Scanner (precision, accuracy and speed of acquisition) were combined with the Total Station procedure (precision) using the classical digital photomosaic technique

Estudo integrado de análogo a reservatórios petrolíferos fluviais: caracterização, parametrização e modelagem tridimensional de depósitos recentes do Rio Assu (Rio Grande do Norte/Brasil)

This work shows a integrated study of modern analog to fluvial reservoirs of Açu Formation (Unit 3). The modern analog studied has been Assu River located in the same named city, Rio Grande do Norte State, Northeast of Brazil. It has been developed a new methodology to parameterizating the fluvial geological bodies by GPR profile (by central frequency antennas of 50, 100 and 200 MHz). The main parameters obtained were width and thickness. Still in the parameterization, orthophotomaps have been used to calculate the canal sinuosity and braided parameters of Assu River. These information are integrated in a database to supply input data in 3D geological models of fluvial reservoirs. It was made an architectural characterization of the deposit by trench description, GPR profile interpretation and natural expositions study to recognize and describe the facies and its associations, external and internal geometries, boundary surfaces and archtetural elements. Finally, a three-dimensional modeling has been built using all the acquired data already in association with real well data of a reservoir which Rio Assu is considered as analogous. Facies simulations have been used simple kriging (deterministic algorithm), SIS and Boolean (object-based, both stochastics). And, for modeling porosities have used the stochastic algorithm SGS

Sistemas de dunas do parque das Dunas e Barreiras do Inferno/Natal (RN: levantamento geológico /geofísico, elaboração do modelo deterministico e avaliação da vulnerabilidade/suscetibilidade

The current work was developed on the dune systems of the Parque das Dunas and Barreira do Inferno. These places are located in the cities of Natal and Parnamirim (RN, Brazil), respectively. This project has the purpose of developing the deterministic model on a specific blowout at Parque das Dunas, based in the geophysical interpretations of the lines gotten with the Ground Penetration Radar and the planialtimetric acquisitions of the topographical surface of the land. Also analyses of the vulnerability/susceptibility of these dune systems had been done in relation to the human pressures. To develop its deterministic model, it is necessary to acquire inner and outer geometries of the cited blowout. In order to depict inner geometries underneath the surface are used the GPR observing the altimetric control for topographical correction of the GPR lines. As for the outer geometries, the geodesic GPS gives us the planialtimetric points (x, y and z points) with milimetric precision, resulting in high-resolution surfaces. Using interpolation methods of the planialtimetric points was possible create Digital Elevations Models (DEM´s) of these surfaces. As a result, 1,161.4 meters of GPR lines were acquired on the blowout at the Parque das Dunas and 3,735.27 meters on the blowout at the Barreira do Inferno. These lines had been acquired with a 200 MHz antenna, except the 7 and 8 lines, for which we had been used a 100 MHz antenna. The gotten data had been processed and interpreted, being possible to identify boundary surfaces of first, second and third order. The first order boundary surface is related with the contact of the rocks of the Barreiras Group with the aeolian deposits. These deposits had been divided in two groups (Group 1 and Group 2) which are related with the geometry of stratum and the dip of its stratifications. Group 1 presented stratum of sigmoidal and irregular geometries and involved bodies where the reflectors had presented dips that had varied of 20 to the 28 degrees for the Parque das Dunas blowout and of 22 to the 29 degrees for the Barreira do Inferno blowout. Usually, it was limited in the base for the first order surface and in the top for the second order surface. Group 2 presented stratum of trough, wedge or lens geometries, limited in the base for the second order vi surface, where the corresponding deposits had more shown smoothed reflectors or with dips of low angle. The Deterministic and Digital Elevation Models had been developed from the integration and interpretation of the 2D data with the GOCAD® program. In Digital Elevations Models it was possible to see, for the localities, corridor or trough-shaped blowouts. In Deterministic Model it was possible to see first and second order boundary surfaces. For the vulnerability/susceptibility of the dune systems it was applied the methodology proposal by Boderè al (1991); however the same one did not show adequate because it evaluates actual coastal dunes. Actual coastal dunes are dunes that are presented in balance with the current environmental conditions. Therefore, a new methodology was proposal which characterizes the supplying and activity sedimentary, as well as the human pressures. For the methodology developed in this work, both the localities had presented a good management. The Parque das Dunas was characterized as a relic dune system and the Barreira do Inferno was characterized as a palimpsestic dune system. Also two Thematic Maps had been elaborated for the environmental characterization of the studied dune systems, with software ArcGis 8.3, and its respective data bases

Model for the Evaluation of Root Wear by Histometric Analysis

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)