CMOS-based active pixel for low-light-level detection: Analysis and measurements

An analysis of the active pixel sensor (APS), considering the doping profiles of the photodiode in an APS fabricated in a 0.18 μm standard CMOS technology, is presented. A simple and accurate model for the junction capacitance of the photodiode is proposed. An analytic expression for the output voltage of the APS obtained with this capacitance model is in good agreement with measurements and is more accurate than the models used previously. A different mode of operation for the APS based on the dc level of the output is suggested. This new mode has better low-light-level sensitivity than the conventional APS operating mode, and it has a slower temporal response to the change of the incident light power. At 1μW/cm2 and lower levels of light, the measured signal-to-noise ratio (SNR) of this new mode is more than 10 dB higher than the SNR of previously reported APS circuits. Also, with an output SNR of about 10 dB, the proposed dc level is capable of detecting light powers as low as 20 nW/cm2, which is about 30 times lower than the light power detected in recent reports by other groups. © 2007 IEEE.

Air-assistance and low volume application to control of asian rust on soybean crop

Currently, one of factors that cause the production cost increase of soybean crop is the pesticide application. The most important disease in soybean crop is Asian rust, caused by Phakopsora pachyrhizi Sydon & P. Sydon fungus, which can cause significant loss of the production. Therefore, this work aimed at evaluation of different spraying techniques on the spray deposits and some parameters of soybean crop: grain size, weight of 1 000 seeds and the crop productivity. Two experiments were carried out in the experimental area of FCA/UNESP (Faculdade de Ciencias Agronomicas/Universidade Estadual Paulista Julio de Mesquita Filho) - Botucatu, S P, Brazil, in soybean crop, Conquista variety, in the 2007/2008 season. In the first experiment, three air levels (0, 9 and 29 km/h of the air speed generated by fan) with flat fan nozzle XR 8002 with a spray volume of 130 l/ha were compared with a rotating nozzle - using low volume oily - LVO at 40 l/ha of spray volume. The second experiment was carried out under the same conditions as the previous experiment, including a control treatment (untreated plants). The disease severity was evaluated using a diagrammatic scale with a visual evaluation of the disease on 15 leaves of each plot. The grades varied between 0.6 and 78.5% of the disease severity. The use of air assistance when compared with the rotating system nozzle did not show significant differences for spray deposits on adaxial and abaxial surface of the leaves in bottom part of the plant. The air assistance with maximum air speed (29 km/h) increased the productivity with respect of the other treatments.

Photodetection with gate-controlled lateral BJTs from standard CMOS technology

The silicon-based gate-controlled lateral bipolar junction transistor (BJT) is a controllable four-terminal photodetector with very high responsivity at low-light intensities. It is a hybrid device composed of a MOSFET, a lateral BJT, and a vertical BJT. Using sufficient gate bias to operate the MOS transistor in inversion mode, the photodetector allows for increasing the photocurrent gain by 106 at low light intensities when the base-emitter voltage is smaller than 0.4 V, and BJT is off. Two operation modes, with constant voltage bias between gate and emitter/source terminals and between gate and base/body terminals, allow for tuning the photoresponse from sublinear to slightly above linear, satisfying the application requirements for wide dynamic range, high-contrast, or linear imaging. MOSFETs from a standard 0.18-μm triple-well complementary-metal oxide semiconductor technology with a width to length ratio of 8 μm /2 μm and a total area of ∼ 500μm2 are used. When using this area, the responsivities are 16-20 kA/W. © 2001-2012 IEEE.

Storage of sugarcane stalks (Saccharum officinarum cv. SP 79-1011) in low oxygen atmospheres and the effects on enzymatic browning

Although sugarcane consumption is very popular worldwide there are few studies regarding the postharvest storage of stalks that focus on controlling enzymatic browning. The objective of this study was to evaluate the quality of sugarcane stalks stored at 10±1°C in controlled atmosphere with various oxygen (O2) levels (1kPa, 5kPa, 10kPa, 15kPa, and 21kPa) and to verify the effect of this storage on the activities of polyphenoloxidase (PPO) and peroxidase (POD). At 1kPa and 5kPa O2, the stalks' respiratory rate, POD activity, and reducing sugar content were significantly less (P<0.05) than at higher O2 concentrations. In contrast, low O2 levels did not affect PPO activity or influence cane coloration. These results can be used to guide the choice of plastic films, making it possible to store sugarcane stalks in a controlled atmosphere. © 2013 Elsevier B.V.

Streptococcus Mutans Photoinactivation by Combination of Short Exposure of a Broad-Spectrum Visible Light and Low Concentrations of Photosensitizers

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Interfacial integrity of low-shrinkage composite restorations related to the filling technique and consistency

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

TACTILE CARTOGRAPHY EXPERIENCES IN BRAZIL: METHODOLOGIES AND DIDACTICAL MATERIAL WITH TECHNOLOGICAL RESOURCES FOR INCLUSION OF BLIND AND LOW VISION STUDENTS

The tactile cartography is an area of Cartography that aims the development of methodologies and didactical material to work cartographic concepts with blind and low vision people. The main aim of this article is to present the experience of Tactile Cartography Research Group from Sao Paulo State University (UNESP), including some didactical material and courses for teachers using the System MAPAVOX. The System MAPAVOX is software developed by our research group in a partnership with Federal University of Rio de Janeiro (UFRJ) that integrates maps and models with a voice synthesizer, sound emission, texts, images and video visualizing for computers. Our research methodology is based in authors that have in the students the centre of didactical activity such as Ochaita and Espinosa in [1], which developed studies related to blind children's literacy. According to Almeida the child's drawing is, thus, a system of representation. It isn't a copy of objects, but interpretation of that which is real, done by the child in graphic language[2]. In the proposed activities with blind and low vision students they are prepared to interpret reality and represent it by adopting concepts of graphic language learned. To start the cartographic initialization it is necessary to use personal and quotidian references, for example the classroom tactile model or map, to include concepts in generalization and scale concerning to their space of life. During these years many case studies were developed with blind and low vision students from Special School for Hearing Impaired and Visually Impaired in Araras and Rio Claro, Sao Paulo - Brazil. The most part of these experiences and others from Brazil and Chile are presented in [3]. Tactile material and MAPAVOX facilities are analysed by students and teachers who contribute with suggestions to reformulate and adapt them to their sensibility and necessity. Since 2005 we offer courses in Tactile Cartography to prepare teachers from elementary school in the manipulation of didactical material and attending students with special educational needs in regular classroom. There were 6 classroom and blended courses offered for 184 teachers from public schools in this region of the Sao Paulo state. As conclusion we can observe that methodological procedures centred in the blind and low vision students are successful in their spatial orientation if use didactical material from places or objects with which they have significant experience. During the applying of courses for teachers we could see that interdisciplinary groups can find creative cartographic alternatives more easily. We observed too that the best results in methodological procedures were those who provided concreteness to abstract concepts using daily experiences.

Effect of the addition of wheat fiber and partial pork back fat on the chemical composition, texture and sensory property of low-fat bologna sausage containing inulin and oat fiber

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A low-power silicon-on-insulator PWM discriminator for biomedical applications

A CMOS/SOI circuit to decode PWM signals is presented as part of a body-implanted neurostimulator for visual prosthesis. Since encoded data is the sole input to the circuit, the decoding technique is based on a double-integration concept and does not require dc filtering. Nonoverlapping control phases are internally derived from the incoming pulses and a fast-settling comparator ensures good discrimination accuracy in the megahertz range. The circuit was integrated on a 2 mu m single-metal SOI fabrication process and has an effective area of 2mm(2) Typically, the measured resolution of encoding parameter a was better than 10% at 6MHz and V-DD=3.3V. Stand-by consumption is around 340 mu W. Pulses with frequencies up to 15MHz and alpha = 10% can be discriminated for V-DD spanning from 2.3V to 3.3V. Such an excellent immunity to V-DD deviations meets a design specification with respect to inherent coupling losses on transmitting data and power by means of a transcutaneous link.

Feasibility of solar heating systems composed of recyclable packaging for low-income rural communities

Solar heaters are an appropriate technology in tropical and sub-tropical climates to heat bath water by solar energy. Low-cost solar heaters meet the demand of low-income rural communities which currently do not have access to this technology. Current research analyzes the economic viability of solar heaters, built with recyclable materials, to reduce electric energy bill. A solar heating system was built consisting of recyclable materials in accordance with the manuals provided by the Secretariat of Environment of the state of Paraná (SEMA). Duration of use of electric showers by families of rural properties was determined to calculate expenses and billing of electricity. Simulation and material costs showed that the system was feasible. Commercial solar heaters could be replaced at a cost of R$ 22.61 per month during 13 months.

Leveraging Technology for the Future of Nebraska: Creating a Statewide Broadband Plan

In Nebraska, some areas of the state S primarily in the most rural areas of the state S may be underserved or unserved in terms of broadband access. Rural areas of the state also lag in economic development and are experiencing population losses. Additionally, broadband adoption and Internet usage among certain income and population groups remains low. Increasing adoption of broadband and Information Technology (IT) services is one way to create economic opportunities, attract new residents to rural areas and address economic inequalities among population groups.

Lean diesel technology and human health: a case study in six Brazilian metropolitan regions

OBJECTIVE: Due to their toxicity, diesel emissions have been submitted to progressively more restrictive regulations in developed countries. However, in Brazil, the implementation of the Cleaner Diesel Technologies policy (Euro IV standards for vehicles produced in 2009 and low-sulfur diesel with 50 ppm of sulfur) was postponed until 2012 without a comprehensive analysis of the effect of this delay on public health parameters. We aimed to evaluate the impact of the delay in implementing the Cleaner Diesel Technologies policy on health indicators and monetary health costs in Brazil. METHODS: The primary estimator of exposure to air pollution was the concentration of ambient fine particulate matter (particles with aerodynamic diameters, <2.5 mu m, [PM2.5]). This parameter was measured daily in six Brazilian metropolitan areas during 2007-2008. We calculated 1) the projected reduction in the PM2.5 that would have been achieved if the Euro IV standards had been implemented in 2009 and 2) the expected reduction after implementation in 2012. The difference between these two time curves was transformed into health outcomes using previous dose-response curves. The economic valuation was performed based on the DALY (disability-adjusted life years) method. RESULTS: The delay in implementing the Cleaner Diesel Technologies policy will result in an estimated excess of 13,984 deaths up to 2040. Health expenditures are projected to be increased by nearly US$ 11.5 billion for the same period. CONCLUSIONS: The present results indicate that a significant health burden will occur because of the postponement in implementing the Cleaner Diesel Technologies policy. These results also reinforce the concept that health effects must be considered when revising fuel and emission policies.

Anti-Atherogenic Effects of a Phenol-Rich Fraction from Brazilian Red Wine (Vitis labrusca L.) in Hypercholesterolemic Low-Density Lipoprotein Receptor Knockout Mice

Moderate wine intake (i.e., 1-2 glasses of wine a day) is associated with a reduced risk of morbidity and mortality from cardiovascular disease. The aim of this study was to evaluate the anti-atherosclerotic effects of a nonalcoholic ethyl acetate fraction (EAF) from a South Brazilian red wine obtained from Vitis labrusca grapes. Experiments were carried out on low-density lipoprotein (LDL) receptor knockout (LDLr-/-) mice, which were subjected to a hypercholesterolemic diet and treated with doses of EAF (3, 10, and 30 mg/kg) for 12 weeks. At the end of the treatment, the level of plasma lipids, the vascular reactivity, and the atherosclerotic lesions were evaluated. Our results demonstrated that the treatment with EAF at 3 mg/kg significantly decreased total cholesterol, triglycerides, and LDL plus very low-density lipoprotein levels compared with control hypercholesterolemic mice. The treatment of mice with EAF at 3 mg/kg also preserved the vasodilatation induced by acetylcholine on isolated thoracic aorta from hypercholesterolemic LDLr-/- mice. This result is in agreement with the degree of lipid deposit on arteries. Taken together, the results show for the first time that the lowest concentration of an EAF obtained from a red wine produced in southern Brazil significantly reduced the progression of atherosclerosis in mice.

Immunohistochemical features of claudin-low intrinsic subtype in metaplastic breast carcinomas

Purpose: The claudin-low molecular subtype of breast cancer includes triple negative invasive carcinomas, with a high frequency of metaplastic and medullary features. The aim of this study was to evaluate the immunohistochemistry expression of claudins in a series of metaplastic breast carcinomas. We also assessed other claudin-low features, such as the cancer stem cell-like and epithelial-to-mesenchymal transition phenotypes. Results: The majority of the cases showed weak or negative staining for membrane claudins expression. We found 76.9% (10/13) low expressing cases for claudin-1, 84.6% (11/13) for claudin-3 and claudin-4, and 92.3% (12/13) for claudin-7. Regarding the cancer stem cell marker ALDH1, 30.8% (4/13) showed positive staining. We also showed that the majority of the cases presented a CD44(+)CD24(-/low) phenotype, positivity for vimentin and lack of E-cadherin expression. Interestingly, these claudin-low molecular features were specific of the mesenchymal component of metaplastic breast carcinomas, since its frequency was very low in other breast cancer molecular subtypes, as luminal, HER2-overexpressing and non-metaplastic triple negative tumors. Conclusions: The negative/low expression of claudins and E-cadherin, high levels of vimentin, and the breast cancer stem cell phenotype suggests that metaplastic breast carcinomas have similar features to the ones included in the claudin-low molecular subtype, specially their mesenchymal components. (C) 2012 Elsevier Ltd. All rights reserved.

Low liquid-solid ratio (LSR) hot water pretreatment of sugarcane bagasse

Low liquid-solid ratio (LSR) can be used to obtain high-content xylo-oligosaccharide (XOS) spend liquor by hot water pretreatment. Developing a technology based on low LSR results in more efficient water usage in the system and thus in lower capital and operating costs. Xylans from xylan rich agro-industrial waste are abundant hemicellulosic polymers with enormous potential for industrial applications. Currently, freeze-dried xylo-oligosaccharides are used as bio-based polymers and hydrolysates containing high xylose contents are converted to several chemical products. In this study, sugarcane bagasse was treated with water at low LSRs and mild temperatures in order to assess the effects of varying the pretreatment conditions on the xylo-oligosaccharide and xylose concentrations, and use a central composite experimental design to optimize the process parameters. The pretreatments were performed in the ranges temperature: 143.3-176.7 degrees C, time: 20-70 min and LSR: 1 : 1 to 11 : 1 (g g(-1)). The maximum concentrations of xylose and xylan were 13.76 and 36.18 g L-1 (equivalent to 48.29 g L-1 of xylan), respectively, which were achieved by treating bagasse at 170 degrees C for 60 min, with LSR of 3 g g(-1). The amount of xylan removed under these conditions was almost 57%. The soluble xylan consisted mainly of xylo-oligosaccharides (74 wt% of the identified compound in the spent liquor).