Sviluppo di modelli motore e veicolo per l'analisi di strategie di controllo in applicazioni Software e Hardware In the Loop

This work describes the development of a simulation tool which allows the simulation of the Internal Combustion Engine (ICE), the transmission and the vehicle dynamics. It is a control oriented simulation tool, designed in order to perform both off-line (Software In the Loop) and on-line (Hardware In the Loop) simulation. In the first case the simulation tool can be used in order to optimize Engine Control Unit strategies (as far as regard, for example, the fuel consumption or the performance of the engine), while in the second case it can be used in order to test the control system. In recent years the use of HIL simulations has proved to be very useful in developing and testing of control systems. Hardware In the Loop simulation is a technology where the actual vehicles, engines or other components are replaced by a real time simulation, based on a mathematical model and running in a real time processor. The processor reads ECU (Engine Control Unit) output signals which would normally feed the actuators and, by using mathematical models, provides the signals which would be produced by the actual sensors. The simulation tool, fully designed within Simulink, includes the possibility to simulate the only engine, the transmission and vehicle dynamics and the engine along with the vehicle and transmission dynamics, allowing in this case to evaluate the performance and the operating conditions of the Internal Combustion Engine, once it is installed on a given vehicle. Furthermore the simulation tool includes different level of complexity, since it is possible to use, for example, either a zero-dimensional or a one-dimensional model of the intake system (in this case only for off-line application, because of the higher computational effort). Given these preliminary remarks, an important goal of this work is the development of a simulation environment that can be easily adapted to different engine types (single- or multi-cylinder, four-stroke or two-stroke, diesel or gasoline) and transmission architecture without reprogramming. Also, the same simulation tool can be rapidly configured both for off-line and real-time application. The Matlab-Simulink environment has been adopted to achieve such objectives, since its graphical programming interface allows building flexible and reconfigurable models, and real-time simulation is possible with standard, off-the-shelf software and hardware platforms (such as dSPACE systems).

Sviluppo di algoritmi di RCP per la stima della coppia indicata erogata da un motore a combustione interna.

Combustion control is one of the key factors to obtain better performances and lower pollutant emissions for diesel, spark ignition and HCCI engines. An algorithm that allows estimating, as an example, the mean indicated torque for each cylinder, could be easily used in control strategies, in order to carry out cylinders trade-off, control the cycle to cycle variation, or detect misfires. A tool that allows evaluating the 50% of Mass Fraction Burned (MFB50), or the net Cumulative Heat Release (CHRNET), or the ROHR peak value (Rate of Heat Release), could be used to optimize spark advance or to detect knock in gasoline engines and to optimize injection pattern in diesel engines. Modern management systems are based on the control of the mean indicated torque produced by the engine: they need a real or virtual sensor in order to compare the measured value with the target one. Many studies have been performed in order to obtain an accurate and reliable over time torque estimation. The aim of this PhD activity was to develop two different algorithms: the first one is based on the instantaneous engine speed fluctuations measurement. The speed signal is picked up directly from the sensor facing the toothed wheel mounted on the engine for other control purposes. The engine speed fluctuation amplitudes depend on the combustion and on the amount of torque delivered by each cylinder. The second algorithm processes in-cylinder pressure signals in the angular domain. In this case a crankshaft encoder is not necessary, because the angular reference can be obtained using a standard sensor wheel. The results obtained with these two methodologies are compared in order to evaluate which one is suitable for on board applications, depending on the accuracy required.

Analisi di vulnerabilità di un ponte ferroviario ad arco in muratura

L'elaborato è sviluppato sullo studio della vulnerabilità sismica globale e locale di un ponte ad arco in muratura.

Un metodo multilivello per la semplificazione di mesh poligonali da scanner 3D

L'algoritmo di semplificazione proposto in questa tesi agisce in modo iterativo su due livelli, in una prima fase alla mesh viene applicato un operatore di smoothing e alla mesh così elaborata viene poi applicata la decimazione. L'alternanza di questi due operatori permette di avere mesh semplificate che mantengono però una qualità maggiore rispetto al risultato che si avrebbe invece applicando solo la decimazione. A partire da una mesh ad alta risoluzione, ad ogni iterazione viene quindi creata una mesh con una risoluzione inferiore fino all'ultima iterazione che produce la mesh coarse (a bassa risoluzione) desiderata. Si viene quindi a creare una struttura di semplificazione multilivello, utile in molte applicazioni di computer graphics.

Progettazione robusta di un motore Stirling

Descrizione dell'applicazione di tecniche di progettazione robusta, robust design, ad un motore Stirling per generazione di corrente elettrica. La progettazione robusta è una tecnica che permette lo sviluppo di prodotti cercando di minimizzare gli effetti negativi dovuti a variazioni inaspettate nei parametri di progetto, interessante, quindi, perchè in ambito industriale accade spesso che i valori nominali dei parametri per cui si progetta un dispositivo od una macchina siano diversi da quelli che si presentano nel suo reale funzionamento.