Crystal structure of quenched and in-field electroluminescent phosphors

Electroluminescent zinc sulfide doped with copper and chloride (ZnS:Cu, Cl) powder was heated to 400°C and rapidly quenched to room temperature. Comparison between the quenched and non-quenched phosphors using synchrotron radiation X-ray powder diffraction (XRPD) (λ = 0.828692 Å) and X-ray absorption spectroscopy (XAS) was made. XRPD shows that the expected highly faulted structure is observed with excellent resolution out to 150° 2θ (or to (12 2 2) of the sphalerite phase). The quenched sample compared to the unheated sample shows a large change in peak ratios between 46.7° and 46.9°, which is thought to correspond to the wurtzite (0 0 6), (0 3 2) and sphalerite (3 3 3)/(5 1 1) peaks. Hence, a large proportion of this sphalerite diffraction is lost from the material upon rapid quenching, but not when the material is allowed to cool slowly. The Zn K-edge XAS data indicate that the crystalline structures are indistinguishable using this technique, but do give an indication that the electronic structure has altered due to changing intensity of the white line. It is noted that the blue electroluminescence (EL) emission bands are lost upon quenching: however, a large amount of total EL emission intensity is also removed, which is consistent with our findings. We report the XRPD of a working alternating-current electroluminescence device in the synchrotron X-ray beam, which exhibits a new diffraction pattern when the device is powered in an AC field even though the phosphor is fixed in the binder. Significantly, only a few crystals are required to yield the diffraction data because of the high flux X-ray source. These in panel data show multiple sharp diffraction lines spread out under the region, where capillary data show broad diffraction intensity indicating that the phosphor powder is comprised of unique crystals, each having different structures.

Notices of Brazil in 1828 and 1929

Contém notas detalhadas da viagem do sacerdote inglês, em meados do Século XIX, às Províncias do Rio de Janeiro e de Minas Gerais, com especial atenção aos fenômenos sociais, enfatizando a situação dos escravos no Brasil, seu tráfico desde o descobrimento até a coroação de D.Pedro I. Reproduz, no apêndice do volume 2, documentos históricos e a partitura do Hino Imperial, composto por D. Pedro I, conforme anotações de Borba de Moraes.

Gillraker analysis and speciation in the thread herring genus Opisthonema

ENGLISH: The thread herrings, genus Opisthonema, family Clupeidae, are marine fishes that occur only in tropical and subtropical waters off both coasts of the American continent. The genus is composed of one Atlantic species and four Pacific species. Opisthonema oglinum (LeSueur), the single species in the western Atlantic Ocean, occurs from Brazil to Massachusetts, at Bermuda, and throughout the West Indies. Opisthonema libertate (Günther), Opisthonema bulleri (Regan), and Opisthonema medirastre, new species, are Pacific coastal species which occur together from Peru to Mexico (with at least one occasionally in California). Opisthonema berlangai, new species, is confined to the vicinity of the Galapagos Islands. SPANISH: Los arenques de hebra, género Opisthonema, familia Clupeidae, son peces marinos que se encuentran sólo en aguas tropicales y subtropicales cerca a ambas costas del continente americano. El género está compuesto de una especie en el Atlántico y de cuatro en el Pacifico. Opisthonema oglinum (LeSueur), única especie que medra el Océano Atlántico occidental, se encuentra del Brasil a Massachusetts, en Bermuda, y las Indias Occidentales. Opisthonema libertate (Günther), Opisthonema bulleri (Regan), y Opisthonema medirastre, especie nueva, son especies costaneras del Pacífico que aparecen entremezcladas del Perú a México (ocasionalmente por lo menos una de ellas en California). Opisthonema berlangai, especie nueva, está confinada a la vecindad de las Islas Galápagos.

The diagnostic morphological features of British Sigara striata, S. dorsalis and intermediate specimens (Corixidae), with a new key for identification of adult males

There are 34 species of the family Corixidae (Hemiptera Heteroptera) in Britain and Ireland of which Sigara striata and Sigara dorsalis are the only two British representatives. In this article the authors briefly consider a range of diagnostic features that may be used to separate British specimens of striata from dorsalis. Most of these morphological features have been used in keys to the British species of the subgenus Sigara sensu strictu. A scoring system has also been devised to facilitate the identification of individuals from the southeast of England, although it is applicable to the whole of the British Isles, and a new (short) key is presented.

Acid precipitation and its effects on aquatic systems in the English Lake District

There is no evidence of an increase in the acidity (lower pH or alkalinity) of water-bodies in the Lake District over the last 50 years. Brown trout occur in acid streams and upland tarns where pH is 4.5-5.2 throughout the year. Their occurrence in such waters in Britain and Ireland has been known for most of this century and there is no previous evidence of harmful effects on salmonid fisheries, though numbers of fish are naturally low. However, many benthic invertebrates that are common in hill-streams where pH is above 5.7 do not occur in more acid streams. This phenomenon occurs in the headwaters of several western rivers in Cumbria. It is not a recent response to "acid rain". Harmful effects of pH are undoubtedly more pronounced in waters that are poor in other dissolved ions. Low concentrations of sodium, potassium, calcium and chloride are especially important and may limit the distributions of some aquatic animals even where pH is above 5.7. The concentration of sulphate ions is usually relatively high but this is not important to the fauna; concentrations are at least two times higher in productive alkaline water-bodies than they are in unproductive acid waters.

Lethal Parasites in Oysters from Coastal Georgia with Discussion of Disease and Management Implications

Extensive mortalities of oysters, Crassostrea virginica, occurred from 1985 through 1987 in coastal waters of Georgia. Fluid thioglycolate cultures of oysters collected from 16 of 17 locations revealed infections by the apicomplexan parasite Perkinsus marinus. An ascetosporan parasite, Haplosporidium nelsoni, was also observed in histopathological examination of oysters from 4 of the locations. While the range of H. nelsoni currently is recognized as the east coast of the United States from Maine to Florida, this is the first report of the parasite in Georgia waters. This paper documents the occurrence of these two lethal parasites in oysters from coastal waters of Georgia, along with potential disease and management implications. Results of an earlier independent and previously unpublished survey are also discussed which document the presence of P. marinus in Georgia as early as 1966.

Drought frequency analysis for California from observed, synthetic, and proxy data

Drought frequency analysis can be performed with statistical techniques developed for determining recurrence intervals for extreme precipitation and flood events (Linsley et al 1992). The drought analysis method discussed in this paper uses the log-Pearson Type III distribution, which has been widely used in flood frequency research. Some of the difficulties encountered when using this distribution for drought analysis are investigated.

Semiempirical down-scaling of GCM output to the local scale for temperature, precipitation, and runoff

EXTRACT (SEE PDF FOR FULL ABSTRACT): An empirically derived multiple linear regression model is used to relate a local-scale dependent variable (either temperature, precipitation, or surface runoff) measured at individual gauging stations to six large-scale independent variables (temperature, precipitation, surface runoff, height to the 500-mbar pressure surface, and the zonal and meridional gradient across this surface). ...The area investigated is the western United States. ... The calibration data set is from 1948 through 1988 and includes data from 268 joint temperature and precipitation stations, 152 streamflow stations (which are converted to runoff data), and 24 gridded 500-mbar pressure height nodes.

Influence of film cooling hole angles and geometries on aerodynamic loss and net heat flux reduction

Turbine design engineers have to ensure that film cooling can provide sufficient protection to turbine blades from the hot mainstream gas, while keeping the losses low. Film cooling hole design parameters include inclination angle (α), compound angle (β ), hole inlet geometry and hole exit geometry. The influence of these parameters on aerodynamic loss and net heat flux reduction is investigated, with loss being the primary focus. Low-speed flat plate experiments have been conducted at momentum flux ratios of IR = 0.16, 0.64 and 1.44. The film cooling aerodynamic mixing loss, generated by the mixing of mainstream and coolant, can be quantified using a three-dimensional analytical model that has been previously reported by the authors. The model suggests that for the same flow conditions, the aerodynamic mixing loss is the same for holes with different α and β but with the same angle between the mainstream and coolant flow directions (angle κ). This relationship is assessed through experiments by testing two sets of cylindrical holes with different α and β : one set with κ = 35°, another set with κ = 60°. The data confirm the stated relationship between α, β, κ and the aerodynamic mixing loss. The results show that the designer should minimise κ to obtain the lowest loss, but maximise β to achieve the best heat transfer performance. A suggestion on improving the loss model is also given. Five different hole geometries (α =35.0°, β =0°) were also tested: cylindrical hole, trenched hole, fan-shaped hole, D-Fan and SD-Fan. The D-Fan and the SD-Fan have similar hole exits to the fan-shaped hole but their hole inlets are laterally expanded. The external mixing loss and the loss generated inside the hole are compared. It was found that the D-Fan and the SD-Fan have the lowest loss. This is attributed to their laterally expanded hole inlets, which lead to significant reduction in the loss generated inside the holes. As a result, the loss of these geometries is ≈ 50 % of the loss of the fan-shaped hole at IR = 0.64 and 1.44. Copyright © 2011 by ASME.

Influence of film cooling hole angles and geometries on aerodynamic loss and net heat flux reduction

Turbine design engineers have to ensure that film cooling can provide sufficient protection to turbine blades from the hot mainstream gas, while keeping the losses low. Film cooling hole design parameters include inclination angle (a), compound angle (b), hole inlet geometry, and hole exit geometry. The influence of these parameters on aerodynamic loss and net heat flux reduction is investigated, with loss being the primary focus. Low-speed flat plate experiments have been conducted at momentum flux ratios of IR=0.16, 0.64, and 1.44. The film cooling aerodynamic mixing loss, generated by the mixing of mainstream and coolant, can be quantified using a three-dimensional analytical model that has been previously reported by the authors. The model suggests that for the same flow conditions, the aerodynamic mixing loss is the same for holes with different a and b but with the same angle between the mainstream and coolant flow directions (angle k). This relationship is assessed through experiments by testing two sets of cylindrical holes with different a and b: one set with k=35 deg, and another set with k=60 deg. The data confirm the stated relationship between α, β, k and the aerodynamic mixing loss. The results show that the designer should minimize k to obtain the lowest loss, but maximize b to achieve the best heat transfer performance. A suggestion on improving the loss model is also given. Five different hole geometries (α=35.0 deg, β=0 deg) were also tested: cylindrical hole, trenched hole, fan-shaped hole, D-Fan, and SD-Fan. The D-Fan and the SD-Fan have similar hole exits to the fan-shaped hole but their hole inlets are laterally expanded. The external mixing loss and the loss generated inside the hole are compared. It was found that the D-Fan and the SD-Fan have the lowest loss. This is attributed to their laterally expanded hole inlets, which lead to significant reduction in the loss generated inside the holes. As a result, the loss of these geometries is≈50% of the loss of the fan-shaped hole at IR=0.64 and 1.44. © 2013 by ASME.

Four nations feminism: Una Troy and Menna Gallie

The emergence of four nations framework in literary and historical scholarship has helped us to arrive at a fuller understanding of the complex and overlapping histories of the islands of Britain and Ireland, while recent research into Wales and Ireland in particular has helped to make the map of our relations more fully comprehensible. But what is the relevance and meaning of the four nations context for womenâ s writing in Ireland and Wales? What part does gender play in the interconnected histories of Wales and Ireland, and how are questions of sexual and artistic identity addressed within texts that imagine British-Irish history in gendered terms? This lecture identifies finds evidence of a feminist reimagining of archipelagic relationships by two writers: Munster novelist and playwright Una Troy, and Welsh writer Menna Gallie, born into a mining community on the western edge of the South Wales coalfields. Both Troy and Gallie wrote novels that deploy plots of female friendship to interrogate the relationship between gender and national affiliation in a four nations context.