Heat Transfer in an Airfoil Shaped Strut

The heat transfer from a hot primary flow stream passing over the outside of an airfoil shaped strut to a cool secondary flow stream passing through the inside of that strut was studied experimentally and numerically. The results showed that the heat transfer on the inside of the strut could be reliably modeled as a developing flow and described using a power law model. The heat transfer on the outside of the strut was complicated by flow separation and stall on the suction side of the strut at high angles of attack. This separation was quite sensitive to the condition of the turbulence in the flow passing over the strut, with the size of the separated wake changing significantly as the mean magnitude and levels of anisotropy were varied. The point of first stall moved by as much as 15% of the chord, while average heat transfer levels changed by 2-5% as the inlet condition was varied. This dependence on inlet conditions meant that comparisons between experiment and steady RANS based CFD were quite poor. Differences between the CFD and experiment were attributed to anisotropic and unsteady effects. The coupling between the two flows was shown to be quite low - that is to say, heat transfer coefficients on both the inner and outer surfaces of the strut were relatively unaffected by the temperature of the strut, and it was possible to predict the temperature on the strut surface quite reliably using heat transfer data from decoupled tests, especially for CFD simulations.

Sedimentology of a Middle Jurassic Base-of-Slope environment, Cutri Formation, Mallorca

The Cutri Formation’s, type location, exposed in the NW of Mallorca, Spain has previously been described by Álvaro et al., (1989) and further interpreted by Abbots (1989) unpublished PhD thesis as a base-of-slope carbonate apron. Incorporating new field and laboratory analysis this paper enhances this interpretation. From this analysis, it can be shown without reasonable doubt that the Cutri Formation was deposited in a carbonate base-of-slope environment on the palaeowindward side of a Mid-Jurassic Tethyan platform. Key evidence such as laterally extensive exposures, abundant deposits of calciturbidtes and debris flows amongst hemipelagic deposits strongly support this interpretation.

Diseño de una turbina experimental de vapor de baja potencia.

Este trabajo se enfoca en el diseño de una turbina de vapor de carácter experimental para simular, en un laboratorio de transferencia térmica, la dinámica propia de una turbina de mayor tamaño en el circuito secundario de un ciclo de potencia. La máquina diseñada produciría 185 kW de potencia en el eje a 9.000 RPM con un rendimiento interno del 88 %, tomando en la entrada 0,4 kg/s de vapor saturado a 40 bar y descargando a una presión de 1,5 bar. Se desarrolló la teoría de turbomáquinas necesaria para realizar los cálculos fuidodinámicos y se propuso un método de diseño apropiado para el alcance del trabajo. Se decidió que la turbina sería de tres etapas, dos Curtis y una de impulso, y se realizaron los cálculos correspondientes. Una vez que el diseño fluidodinámico estaba definido, se procedió a dimensionar los distintos elementos mecánicos, con el alcance correspondiente a ingeniería conceptual y básica. Se realizaron detalladamente los cálculos propios del dimensionado del rotor (eje y discos), rodamientos, carcasa, válvula de seguridad de presión y asociados. Además se presentó el diseño conceptual de los elementos restantes, sistema de control y otros auxiliares. Finalmente, se realizaron los modelos en software 3D de todas las piezas y se produjeron los planos correspondientes.

Dynamics of an axisymmetric electromagnetic 'crucible' melting

Different industrial induction melting processes involve free surface and melt-solid interface of the liquid metal subject to dynamic change during the technological operation. Simulation of the liquid metal dynamics requires to solve the non-linear, coupled hydrodynamic-electromagnetic-heat transfer problem accounting for the time development of the liquid metal free boundary with a suitable turbulent viscosity model. The present paper describes a numerical solution method applicable for various axisymmetric induction melting processes, such as, crucible with free top surface, levitation, semi-levitation, cold crucible and similar melting techniques. The presented results in the cases of semi-levitation and crucible with free top surface meltings demonstrate oscillating transient behaviour of the free metal surface indicating the presence of gravity-inertial-electromagnetic waves which are coupled to the internal fluid flow generated by both the rotational and potential parts of the electromagnetic force.

Diseño de una turbina experimental de vapor de baja potencia.

Este trabajo se enfoca en el diseño de una turbina de vapor de carácter experimental para simular, en un laboratorio de transferencia térmica, la dinámica propia de una turbina de mayor tamaño en el circuito secundario de un ciclo de potencia. La máquina diseñada produciría 185 kW de potencia en el eje a 9.000 RPM con un rendimiento interno del 88 %, tomando en la entrada 0,4 kg/s de vapor saturado a 40 bar y descargando a una presión de 1,5 bar. Se desarrolló la teoría de turbomáquinas necesaria para realizar los cálculos fuidodinámicos y se propuso un método de diseño apropiado para el alcance del trabajo. Se decidió que la turbina sería de tres etapas, dos Curtis y una de impulso, y se realizaron los cálculos correspondientes. Una vez que el diseño fluidodinámico estaba definido, se procedió a dimensionar los distintos elementos mecánicos, con el alcance correspondiente a ingeniería conceptual y básica. Se realizaron detalladamente los cálculos propios del dimensionado del rotor (eje y discos), rodamientos, carcasa, válvula de seguridad de presión y asociados. Además se presentó el diseño conceptual de los elementos restantes, sistema de control y otros auxiliares. Finalmente, se realizaron los modelos en software 3D de todas las piezas y se produjeron los planos correspondientes.

Interview with Hans G. Hornung

An interview in two sessions, June and July 2014, with Hans Georg Hornung, Clarence L. Johnson Professor of Aeronautics, emeritus, in the Division of Engineering and Applied Science. Dr. Hornung describes the origins of the German Templer Colony in Palestine and his upbringing there before and during World War II. Family moves to Templer settlement, Melbourne, Australia, 1948. He attends technical college; University of Melbourne; master’s in engineering, 1962. Researcher, Aeronautical Research Laboratories, Melbourne; PhD, Imperial College, London, 1965. He recalls his academic career at the Australian National University, Canberra (1967-1980); his interest in hypersonics; building free-piston shock tunnel with Raymond Stalker. Sabbatical in Darmstadt with Ernst Becker. Seven years as director of fluid-mechanics institute of the DLR [Deutsches Zentrum für Luft- und Raumfahrt], in Göttingen. Comes to Caltech in 1987 to succeed Hans W. Liepmann as director of GALCIT [Graduate Aerospace Laboratories, California Institute of Technology]. Recalls his various aero colleagues, his work with Rocketdyne on Caltech’s T5 (successor to Canberra’s T3 shock tunnel) and Ludwieg tube, collaboration with JPL on space program, and work with graduate students Simon Sanderson and Eric Cummings. Discusses his involvement in various scientific societies and his current activities and continuing research as an emeritus professor.

Simulação computacional como ferramenta de auxílio ao projeto: aplicação em edifícios naturalmente ventilados no clima de Natal/RN

Natural air ventilation is the most import passive strategy to provide thermal comfort in hot and humid climates and a significant low energy strategy. However, the natural ventilated building requires more attention with the architectural design than a conventional building with air conditioning systems, and the results are less reliable. Therefore, this thesis focuses on softwares and methods to predict the natural ventilation performance from the point of view of the architect, with limited resource and knowledge of fluid mechanics. A typical prefabricated building was modelled due to its simplified geometry, low cost and occurrence at the local campus. Firstly, the study emphasized the use of computational fluid dynamics (CFD) software, to simulate the air flow outside and inside the building. A series of approaches were developed to make the simulations possible, compromising the results fidelity. Secondly, the results of CFD simulations were used as the input of an energy tool, to simulate the thermal performance under different rates of air renew. Thirdly, the results of temperature were assessed in terms of thermal comfort. Complementary simulations were carried out to detail the analyses. The results show the potentialities of these tools. However the discussions concerning the simplifications of the approaches, the limitations of the tools and the level of knowledge of the average architect are the major contribution of this study

Simulação numérica da convecção mista em cavidade preenchida com meio poroso heterogêneo e homogêneo

In this work is presented mixed convection heat transfer inside a lid-driven cavity heated from below and filled with heterogeneous and homogeneous porous medium. In the heterogeneous approach, the solid domain is represented by heat conductive equally spaced blocks; the fluid phase surrounds the blocks being limited by the cavity walls. The homogeneous or pore-continuum approach is characterized by the cavity porosity and permeability. Generalized mass, momentum and energy conservation equations are obtained in dimensionless form to represent both the continuum and the pore-continuum models. The numerical solution is obtained via the finite volume method. QUICK interpolation scheme is set for numerical treatment of the advection terms and SIMPLE algorithm is applied for pressure-velocity coupling. Aiming the laminar regime, the flow parameters are kept in the range of 102≤Re≤103 and 103≤Ra≤106 for both the heterogeneous and homogeneous approaches. In the tested configurations for the continuous model, 9, 16, 36, and 64 blocks are considered for each combination of Re and Ra being the microscopic porosity set as constant φ=0,64 . For the pore-continuum model the Darcy number (Da) is set according to the number of blocks in the heterogeneous cavity and the φ. Numerical results of the comparative study between the microscopic and macroscopic approaches are presented. As a result, average Nusselt number equations for the continuum and the pore continuum models as a function of Ra and Re are obtained.

The interaction between two oppositely travelling, horizontally offset, antisymmetric quasi-geostrophic hetons

We investigate numerically the nonlinear interactions between hetons. Hetons are baroclinic structures consisting of two vortices of opposite sign lying at different depths. Hetons are long-lived. They most often translate (they can sometimes rotate) and therefore they can noticeably contribute to the transport of scalar properties in the oceans. Heton interactions can interrupt this translation and thus this transport, by inducing a reconfiguration of interacting hetons into more complex baroclinic multipoles. More specifically, we study here the general case of two hetons, which collide with an offset between their translation axes. For this purpose, we use the point vortex theory, the ellipsoidal vortex model and direct simulations in the three-dimensional quasi-geostrophic contour surgery model. More specifically, this paper shows that there are in general three regimes for the interaction. For small horizontal offsets between the hetons, their vortices recombine as same-depth dipoles which escape at an angle. The angle depends in particular on the horizontal offset. It is a right angle for no offset, and the angle is shallower for small but finite offsets. The second limiting regime is for large horizontal offsets where the two hetons remain the same hetonic structures but are deflected by the weaker mutual interaction. Finally, the intermediate regime is for moderate offsets. This is the regime where the formation of a metastable quadrupole is possible. The formation of this quadrupole greatly restrains transport. Indeed, it constrains the vortices to reside in a closed area. It is shown that the formation of such structures is enhanced by the quasi-periodic deformation of the vortices. Indeed, these structures are nearly unobtainable for singular vortices (point vortices) but may be obtained using deformable, finite-core vortices.

Air Entrainment in the Turbulent Ship Hull Boundary Layer

Turbulent fluctuations in the vicinity of the water free surface along a flat, vertically oriented surface-piercing plate are studied experimentally using a laboratory-scale experiment. In this experiment, a meter-wide stainless steel belt travels horizontally in a loop around two rollers with vertically oriented axes, which are separated by 7.5 meters. This belt device is mounted inside a large water tank with the water level set just below the top edge of the belt. The belt, rollers, and supporting frame are contained within a sheet metal box to keep the device dry except for one 6-meter-long straight test section between rollers. The belt is launched from rest with an acceleration of up to 3-g in order to quickly reach steady state velocity. This creates a temporally evolving boundary layer analogous to the spatially evolving boundary layer created along a flat-sided ship moving at the same velocity, with a length equivalent to the length of belt that has passed the measurement region since the belt motion began. Surface profile measurements in planes normal to the belt surface are conducted using cinematic Laser Induced Fluorescence and quantitative surface profiles are extracted at each instant in time. Using these measurements, free surface fluctuations are examined and the propagation behavior of these free surface ripples is studied. It is found that free surface fluctuations are generated in a region close to the belt surface, where sub-surface velocity fluctuations influence the behavior of these free surface features. These rapidly-changing surface features close to the belt appear to lead to the generation of freely-propagating waves far from the belt, outside the influence of the boundary layer. Sub-surface PIV measurements are performed in order to study the modification of the boundary layer flow field due to the effects of the water free surface. Cinematic planar PIV measurements are performed in horizontal planes parallel to the free surface by imaging the flow from underneath the tank, providing streamwise and wall-normal velocity fields. Additional planar PIV experiments are performed in vertical planes parallel to the belt surface in order to study the bahvior of streamwise and vertical velocity fields. It is found that the boundary layer grows rapidly near the free surface, leading to an overall thicker boundary layer close to the surface. This rapid boundary layer growth appears to be linked to a process of free surface bursting, the sudden onset of free surface fluctuations. Cinematic white light movies are recorded from beneath the water surface in order to determine the onset location of air entrainment. In addition, qualitative observations of these processes are made in order to determine the mechanisms leading to air entrainment present in this flow.

Sloshing and slamming oscillations in collapsible channel flow

We consider laminar high-Reynolds-number flow through a finite-length planar channel, where a portion of one wall is replaced by a thin massless elastic membrane that is held under longitudinal tension T and subject to an external pressure distribution. The flow is driven by a fixed pressure drop along the full length of the channel. We investigate the global stability of two-dimensional Poiseuille flow using a method of matched local eigenfunction expansions, which is compared to direct numerical simulations. We trace the neutral stability curve of the primary oscillatory instability of the system, illustrating a transition from high-frequency ‘sloshing’ oscillations at high T to vigorous ‘slamming’ motion at low T . Small-amplitude sloshing at high T can be captured using a low-order eigenmode truncation involving four surface-based modes in the compliant segment of the channel coupled to Womersley flow in the rigid segments. At lower tensions, we show that hydrodynamic modes contribute increasingly to the global instability and we demonstrate a change in the mechanism of energy transfer from the mean flow, with viscous effects being destabilising. Simulations of finite-amplitude oscillations at low T reveal a generic slamming motion, in which the the flexible membrane is drawn close to the opposite rigid wall before rapidly recovering. A simple model is used to demonstrate how fluid inertia in the downstream rigid channel segment, coupled to membrane curvature downstream of the moving constriction, together control slamming dynamics.