Interferometric and fibre Bragg grating sensor interrogation using an arrayed waveguide grating

We investigate the use of an arrayed waveguide grating (AWG) to interrogate both fibre Bragg grating (FBG) and interferometric sensors. A broadband light source is used to illuminate both the FBG and interferometric sensors. Reflected spectral information is directed to an AWG with integral photodetectors providing 40 electrical outputs. To interrogate interferometric sensors we investigated the dual wavelength technique to measure the distance of a Fabry-Perot cavity, which produced a maximum unambiguous range of 1440μm with an active sensor. Three methods are described to interrogate FBG sensors. The first technique makes use of the reflected light intensity in an AWG channel passband from a narrow bandwidth grating, giving a usable range of 500με and a dynamic strain resolution of 96nε/√Hz at 30Hz. The second approach utilises wide gratings larger than the channel spacing of the AWG; by monitoring the intensity present in corresponding AWG channels an improved range of 1890με was achieved. The third method improves the dynamic range by utilising a heterodyne approach based on interferometric wavelength shift detection providing a dynamic strain resolution of 17nε/√Hz at 30Hz.

Quadratic behaviour of fibre Bragg grating temperature coefficients

We describe the characterization of the temperature and strain responses of fiber Bragg grating sensors by use of an interferometric interrogation technique to provide an absolute measurement of the grating wavelength. The fiber Bragg grating temperature response was found to be nonlinear over the temperature range -70 °C to 80 °C. The nonlinearity was observed to be a quadratic function of temperature, arising from the linear dependence on temperature of the thermo-optic coefficient of silica glass over this range, and is in good agreement with a theoretical model.

Acousto-optic effect in microstructured polymer fiber bragg gratings:simulation and experimental overview

A fine control of the microstructured polymer fiber Bragg grating spectrum properties, such as maximum reflected power and 3-dB bandwidth, through acousto-optic modulation is presented. For simulation purposes, the device is modelled as a single structure, comprising a silica horn and a fiber Bragg grating. For similar sized structures a good correlation between the numerical results and the experimental data is obtained, allowing the strain field to be completely characterized along the whole structure. It is also shown that the microstructured polymer fiber Bragg grating requires less effort from the piezoelectric actuator to produce modification in the grating spectrum when compared with a silica fiber Bragg grating. This technique has potential to be applied on tunable optical filters and tunable cavities for photonic applications.

Embedded fibre Bragg grating array sensors in aluminium alloy matrix by ultrasonic consolidation

Fibre Bragg Grating (FBG) array sensors have been successfully embedded in aluminium alloy matrix by ultrasonic consolidation (UC) technique. The temperature and loading responses of the embedded FBG arrays have been systematically characterised. The embedded grating sensors exhibit an average temperature sensitivity of ~36pm/°C, which is three times higher than that of normal FBGs, and a loading responsivity of ~0.1nm/kg within the dynamic range from 0kg to 3kg. This initial experiment clearly demonstrates that FBG array sensors can be embedded in metal matrix together with other passive and active fibres to fabricate smart materials to monitor the operation and health of engineering structures.

Highly sensitive liquid level sensor using a polymer optical Bragg grating for industrial applications

A novel and highly sensitive liquid level sensor based on a polymer optical fiber Bragg grating (POFBG) is reported for the first time. The sensitivity of the sensor is found to be 57 pm/cm of liquid, enhanced by more than a factor of 5 when compared to an equivalent sensor based on silica fiber. © 2015 OSA.

Proposal and design of phase-modulated fiber gratings in transmission for pulse shaping

A novel approach to pulse shaping using a phase-modulated fiber Bragg grating (FBG) in transmission is proposed and designed. We show that phase-modulated FBGs can provide transmission responses suitable for pulse shaping applications, offering important technological feasibility benefits, since the coupling strength remains basically uniform in the grating. Moreover, this approach retains the substantial advantages of FBGs in transmission, such as optimum energy efficiency, no requirement for an optical circulator, and robustness against fabrication errors.

Design of high channel-count fiber Bragg gratings using tailored group delay

A novel method of fiber Bragg grating design based on tailored group delay is presented. The method leads to designs that are superior to the previously reported results. © OSA 2012.

Graphene-based D-shaped polymer FBG for highly sensitive erythrocyte detection

Graphene-based silica fiber-optic sensors, with high sensitivity, fast response, and low cost, have shown great promise for gas sensing applications. In this letter, by covering a monolayer of p-doped graphene on a D-shaped microstructured polymer fiber Bragg grating (FBG), we propose and demonstrate a novel biochemical probe sensor, the graphene-based D-shaped polymer FBG (GDPFBG). Due to the graphene-based surface evanescent field enhancement, this sensor shows high sensitivity to detect surrounding biochemical parameters. By monitoring the Bragg peak locations of the GDPFBG online, human erythrocyte (red blood cell) solutions with different cellular concentrations ranging from 0 to 104 ppm were detected precisely, with the maximum resolution of sub-ppm. Such a sensor is structurally compact, is clinically acceptable, and provides good recoverability, offering a state-of-the-art polymer-fiber-based sensing platform for highly sensitive in situ and in vivo cell detection applications.

Effect of Rayleigh-scattering distributed feedback on multiwavelength Raman fiber laser generation

We experimentally demonstrate a Raman fiber laser based on multiple point-action fiber Bragg grating (FBG) reflectors and distributed feedback via Rayleigh scattering in a ∼22 km long optical fiber. Twenty two lasing lines with spacing of ∼100 GHz (close to ITU grid) in C-band are generated at Watts power level. In contrast to the normal cavity with competition between laser lines, the random distributed feedback cavity exhibits highly stable multiwavelength generation with a power-equalized uniform distribution which is almost independent on power. The current set up showing the capability of generating Raman gain of about 100-nm wide giving the possibility of multiwavelength generation at different bands. © 2011 SPIE.

一种同时测量温度和应变的光纤光栅传感器

报道了一种新型实用的用单根光纤布拉格光栅(FBG)实现温度和应变分离传感的技术。当光纤光栅一部分包层直径变小时，整个光栅可以看成由两个周期相同但直径不同的子光栅连接而成。理沦分析和实验都证实了这两个子光栅具有相同的温度敏感性和不同的应变敏感性．由此实现光纤光栅传感器中温度和应变两参数的分离测量，而且这两个子光栅的中心波长间距可以直接测量应变大小．温度变化不影响所测量的应变值。实验中光栅的一部分包层直径被HF酸腐蚀到82μm．获得了两子光栅应变响应系数分别为0．00201nm/με．0．000858nm/μ

光纤光栅滤波的瓦斯传感系统的研究

差分吸收法是进行瓦斯远距离监测的重要方法，根据瓦斯在近红外波段的吸收特性，报道了一种新型的远距离光纤瓦斯传感系统。采用1．3μm超辐射发光二极管为光源，利用光纤布拉格光栅(FBG)优良的窄带滤波特性实现了对瓦斯的差分吸收测量。和传统的干涉滤光片相比，光纤光栅滤波器插入损耗低、制备简单。系统具有全光纤化、结构简单、工作距离远、稳定性好的特点。工作距离10km，测量灵敏度为0．1％，是瓦斯爆炸极限的2％。

高分辨率光纤光栅温度传感器的研究

报道了一种具有高分辨率和高效且价廉的解调系统的光纤布拉格光栅(FBG)温度传感器。提出了光纤光栅的金属槽封装技术，以提高传感光栅的温度灵敏性。研究了金属槽封装光栅的温度灵敏性，理论分析和实验结果表明，封装光栅的温度灵敏系数比普通裸光栅提高了3．6倍。系统利用一长周期光栅(LPG)作为线性滤波器，宽带光源经此长周期光栅调制后入射到传感光栅，可解调布拉格传感光栅的波长位移。理论分析与实验结果一致，系统可达到的温度分辨率为0．02℃。

光纤光栅高温传感器的研究

提出了一种能够测量高温的光纤布拉格光栅（FBG）传感器结构。利用线膨胀系数和长度均不同的两种金属细杆和光纤布拉格光栅设计而成的传感头，能够将被测温度转化为光栅的应变，解调由应变引起的光栅波长漂移，即可得知待测的温度。目前在实验室实现了500℃的动态范围和1℃的温度分辨率，实验结果与理论分析一致。

基于3×3耦合器的马赫-曾德尔干涉仪的光纤光栅波长解调技术

介绍了一种基于3×3和2×2光纤耦合器构成的非平衡马赫-曾德尔干涉仪的波长解调方案。理论分析和数据对比表明，相对于由两个2×2光纤耦合器构成的马赫-曾德尔干涉仪，本干涉仪具有宽谱的灵敏度、能跟踪波长的变化方向和相位展开的优点，实验方案用于测量固定在悬臂梁上的传感光纤布拉格光栅（FBG）的峰值波长变化，获得了±1pm的静态波长解调精度，在10Hz处的动态分辨率为27nε/√Hz。相位展开算法使得应变测量范围达到了2014με，对应的相位变化为3．22π。

一种新型结构的单纵模光纤激光器

单纵模掺铒光纤激光器在光通信和光传感等方面有着广泛的应用前景。设计了一种新型的光纤激光器，在光纤环形镜中嵌入未抽运的掺铒光纤作为可饱和吸收体以抑制多纵模，用光纤环谐振腔作为滤波器抑制拍频噪声，用光纤光栅作为波长选择器件，最终得到了单纵模输出并消除了拍频噪声。使用零拍法测量其线宽小于频谱仪的低频极限5kHz。实验结果证明了可饱和吸收体和光纤环的功能。