Subdivision-stabilised immersed b-spline finite elements for moving boundary flows

An immersed finite element method is presented to compute flows with complex moving boundaries on a fixed Cartesian grid. The viscous, incompressible fluid flow equations are discretized with b-spline basis functions. The two-scale relation for b-splines is used to implement an elegant and efficient technique to satisfy the LBB condition. On non-grid-aligned fluid domains and at moving boundaries, the boundary conditions are enforced with a consistent penalty method as originally proposed by Nitsche. In addition, a special extrapolation technique is employed to prevent the loss of numerical stability in presence of arbitrarily small cut-cells. The versatility and accuracy of the proposed approach is demonstrated by means of convergence studies and comparisons with previous experimental and computational investigations.

Tests for conceptual design of 6.6 kV class superconducting fault current limiter with YBCO thin film elements

A superconducting fault current limiter (SFCL) for 6.6 kV and 400 A installed in a cubicle for a distribution network substation was conceptually designed. The SFCL consists of parallel- and series-connected superconducting YBCO elements and a limiting resistor. Before designing the SFCL, some tests were carried out. The width and length of each element used in the tests are 30 mm and 210 mm, respectively. The element consists of YBCO thin film of about 200 nm in thickness on cerium dioxide (CeO2) as a cap-layer on a sapphire substrate by metal-organic deposition with a protective metal coat. In the tests, characteristics of each element, such as over-current, withstand-voltage, and so on, were obtained. From these characteristics, series and parallel connections of the elements, called units, were considered. The characteristics of the units were obtained by tests. From the test results, a single phase prototype SFCL was manufactured and tested. Thus, an SFCL rated at 6.6 kV and 400 A can be designed. © 2009 IEEE.

Seismic analyses of shallow tunnels by dynamic centrifuge tests and finite elements

The increments of internal forces induced in a tunnel lining during earthquakes can be assessed with several procedures at different levels of complexity. However, the substantial lack of well-documented case histories still represents a difficulty in order to validate any of the methods proposed in literature. To bridge this gap, centrifuge model tests were carried out on a circular aluminium tunnel located at two different depths in dense and loose dry sand. Each model has been instrumented for measuring soil motion and internal loads in the lining and tested under several dynamic input signals. The tests performed represented an experimental benchmark to calibrate dynamic analyses with different approaches to account for soil-tunnel kinematic interaction. © 2009 IOS Press.

Recycle of transuranium elements in light water reactors for reduction of geological storage requirements

This paper presents results of a feasibility study aimed at developing a zero-transuranic-discharge fuel cycle based on the U-Th-TRU ternary cycle. The design objective is to find a fuel composition (mixture of thorium, enriched uranium, and recycled transuranic components) and fuel management strategy resulting in an equilibrium charge-discharge mass flow. In such a fuel cycle scheme, the quantity and isotopic vector of the transuranium (TRU) component is identical at the charge and discharge time points, thus allowing the whole amount of the TRU at the end of the fuel irradiation period to be separated and reloaded into the following cycle. The TRU reprocessing activity losses are the only waste stream that will require permanent geological storage, virtually eliminating the long-term radiological waste of the commercial nuclear fuel cycle. A detailed three-dimensional full pressurized water reactor (PWR) core model was used to analyze the proposed fuel composition and management strategy. The results demonstrate the neutronic feasibility of the fuel cycle with zero-TRU discharge. The amount of TRU and enriched uranium loaded reach equilibrium after about four TRU recycles. The reactivity coefficients were found to be within a range typical for a reference PWR core. The soluble boron worth is reduced by a factor of ∼2 from a typical PWR value. Nevertheless, the results indicate the feasibility of an 18-month fuel cycle design with an acceptable beginning-of-cycle soluble boron concentration even without application of burnable poisons.

Ultra-thin 242mAm fuel elements in nuclear reactors

There is a growing interest in using 242mAm as a nuclear fuel. The advantages of 242mAm as a nuclear fuel derive from the fact that 242mAm has the highest thermal fission cross section. The thermal capture cross section is relatively low and the number of neutrons per thermal fission is high. These nuclear properties make it possible to obtain nuclear criticality with ultra-thin fuel elements. The possibility of having ultra-thin fuel elements enables the use of these fission products directly, without the necessity of converting their energy to heat, as is done in conventional reactors. There are three options of using such highly energetic and highly ionized fission products. 1. Using the fission products themselves for ionic propulsion. 2. Using the fission products in an MHD generator, in order to obtain electricity directly. 3. Using the fission products to heat a gas up to a high temperature for propulsion purposes. In this work, we are not dealing with a specific reactor design, but only calculating the minimal fuel elements' thickness and the energy of the fission products emerging from these fuel elements. It was found that it is possible to design a nuclear reactor with a fuel element of less than 1 μm of 242mAm. In such a fuel element, 90% of the fission products' energy can escape.

Multi-hit ballistic damage characterisation of 304 stainless steel plates with finite elements

Multi-impact of projectiles on thin 304 stainless steel plates is investigated to assess the degradation of ballistic performance, and to characterise the inherent mechanisms. Assessment of ballistic degradation is by means of a double-impact of rigid spheres at the same site on a circular clamped plate. The limiting velocity of the second impact, will be altered by the velocity of the antecedent impact. Finite element analyses were used to elucidate experimental results and understand the underlying mechanisms that give rise to the performance degradation. The effect of strength and ductility on the single and multi-impact performance was also considered. The model captured the experimental results with excellent agreement. Moreover, the material parameters used within the model were exclusively obtained from published works with no fitting or calibration required. An attempt is made to quantify the elevation of the ballistic limit of thin plates by the dynamic mechanism of travelling hinges. Key conclusions: The multi-hit performance scales linearly with the single-hit performance; and strength is a significantly greater effector of increased ballistic limit than ductility, even at the expense of toughness. © 2014 Elsevier Ltd.

Identification of the Angel-related elements in cyprinid fishes and their phylogenetic implications

Angel-related element belongs to the family of miniature inverted-repeat transposable elements (MITEs). In this paper we report the identification of an Angel-related element in the series Leuciscini of cyprinid fishes, which is located in the second intron of the growth hormone (GH) gene. We have also found that this element is absent in orthologous locus in the series Barbini of cyprinid fishes, that provides new evidence for the monophyly of the series Leuciscini. The insertion of Angel-related element into the GH gene might take place in the common ancestor of the series Leuciscini after its divergence from the series Barbini. The high sequence divergence and relatively broad species distribution of Angel-related elements implies that they might be ancient transposons which appeared about 26 million years ago.

Total and subcellular distribution of trace elements in the liver of a mother-fetus pair of Dall's porpoises (Phocoenoides dalli)

Total and subcellular hepatic Zn, Cu, Se, Mn, V, Hg, Cd, and Ag were determined in a mother-fetus pair of Dall's porpoises (Phocoenoides dalli). Except for higher fetal Cu concentration, all maternal elements were higher. Elements existed mostly in the cytosol of both animals except in the case of maternal Ag in the microsome and fetal Cu and Ag in the nuclei and mitochondria. In the maternal cytosol, Zn, Mn, Hg, and Ag were present in the high-molecular-weight substances (HMW); Se and V were present in the low-molecular-weight substances (LMW); Cu and Cd were mostly sequestered by metallothionein (MT). In the fetal cytosol, Zn, Se, Mn, Hg, Cd, and Ag were present in the HMW and V in the LMW, while Cu and Ag were mostly associated with MT. MT isoforms were characterized using the HPLC/ICP-MS. Two and four obvious peaks appeared in the maternal and fetal MT fractions, respectively. The highest elemental ion intensities were at a retention time of 7.8 min for the mother, and for the fetus the peak elemental ion intensities occurred at a retention time of 4.3 min, suggesting that different MT isoforms may be involved in elemental accumulation in maternal and fetal hepatocytosols. (C) 2003 Elsevier Ltd. All rights reserved.

Kinetic studies on the effects of rare earth elements (REES) on the growth of Microcystis and their accumulation by Microcystis

In the paper the kinetic effects of La3+ and Ce4+ on the growth of Microcystis and the accumulation kinetics of Microcystis in the single and combined systems of La3+ and Ce4+ were studied. The mechanism of the effects of La3+ and Ce4+ on the growth of Microcystis and their accumulation kinetics were also discussed. In the single system, La3+ stimulated the growth of Microcystis at initial concentrations below 2 mg / 1, but inhibited it above 2 mg / 1. Ce4+ accelerated the growth of Microcystis at initial concentrations below 0.2 mg / 1 and inhibited at above 0.2 mg /l. Furthermore, the stimulation weakened with the increase of initial concentrations of La3+ and Ce4+. In the combined system, the growth of Microcystis was accelerated in the over all cases. In the single system, the amount of La3+ and Ce4+ uptake was more at higher initial concentrations than at lower ones. At the same initial concentrations, La3+ and Ce4+ uptake in the combined system was less than that in the single system. The kinetic process of La3+ and Ce4+ adsorpted by Microcystis can be explained with the second order kinetics adsorption model.

When Does a Polynomial Over a Finite Field Permute the Elements of the Field?

We present a class of indecomposable polynomials of non prime-power degree over the finite field of two elements which are permutation polynomials on infinitely many finite extensions of the field. The associated geometric monodromy groups are the simple ...

Species transformation of trace elements and their distribution prediction in dyestuff residue incineration

The release of heavy metals from the combustion of hazardous wastes is an environmental issue of increasing concern. The species transformation characteristics of toxic heavy metals and their distribution are considered to be a complex problem of mechanism. The behavior of hazardous dyestuff residue is investigated in a tubular furnace under the general condition of hazardous waste pyrolysis and gasfication. Data interpretation has been aided by parallel theoretical study based on a thermodynamic equilibrium model based on the principle of Gibbs free energy minimization. The results show that Ni, Zn, Mn, and Cr are more enriched in dyestuff residue incineration than other heavy metals (Hg, As, and Se) subjected to volatilization. The thermodynamic model calculation is used for explaining the experiment data at 800 degrees C and analyzing species transformation of heavy metals. These results of species transformation are used to predict the distribution and emission characteristics of trace elements. Although most trace element predictions are validated by the measurements, cautions are in order due to the complexity of incineration systems.