Redundancy in interface design and its impact on intuitive use of a product in older users

Many older adults have difficulty using modern consumer products due to their complexity both in terms of functionality and interface design. It has been observed that older people also have more problems learning new systems. It was hypothesised that designing technological products that are more intuitive for older people to use can solve this problem. An intuitive interface allows a user’s to employ prior knowledge, thus minimizing the learning needed for effective interaction. This paper discusses an experiment investigating the effectiveness of redundancy in interface design. The primary objective of this experiment was to find out if using more than one modality for a product’s interface improves the speed and intuitiveness of interactions for older adults. Preliminary analysis showed strong correlation between technology familiarity and time on tasks, but redundancy in interface design improved speed and accuracy of use only for participants with moderate to high technology familiarity.

Mailed treatment to augment primary care for alcohol disorders : a randomised controlled trial

Introduction and Aims: Remote delivery of interventions is needed to address large numbers of people with alcohol use disorders who are spread over large areas. Previous correspondence trials typically examined its effects as stand-alone treatment. This study aimed to test whether adding postal treatment to general practitioner (GP) support would lower alcohol use more than GP intervention alone. Design and Methods: A single-blind, randomised controlled trial with a crossover design was conducted over 12 months on 204 people with alcohol use disorders. Participants in an immediate correspondence condition received treatment over the first 3 months; those receiving delayed treatment received it in months 3–6. Results: Few participants were referred from GPs, and little intervention was offered by them. At 3 months, 78% of participants remained in the study. Those in immediate treatment showed greater reductions in alcohol per week, drinking days, anxiety, depression and distress than those in the delayed condition. However, post-treatment and follow-up outcomes still showed elevated alcohol use, depression, anxiety and distress. Greater baseline anxiety predicted better alcohol outcomes, although more mental distress at baseline predicted dropout. Discussion and Conclusions: The study gave consistent results with those from previous research on correspondence treatments, and showed that high levels of participant engagement over 3 months can be obtained. Substantial reductions in alcohol use are seen, with indications that they are well maintained. However, many participants continue to show high-risk alcohol use and psychological distress.

Problem solving in a middle school robotics design classroom

Little research has been conducted on how students work when they are required to plan, build and evaluate artefacts in technology rich learning environments such as those supported by tools including flow charts, Labview programming and Lego construction. In this study, activity theory was used as an analytic tool to examine the social construction of meaning. There was a focus on the effect of teachers’ goals and the rules they enacted upon student use of the flow chart planning tool, and the tools of the programming language Labview and Lego construction. It was found that the articulation of a teacher’s goals via rules and divisions of labour helped to form distinct communities of learning and influenced the development of different problem solving strategies. The use of the planning tool flow charting was associated with continuity of approach, integration of problem solutions including appreciation of the nexus between construction and programming, and greater educational transformation. Students who flow charted defined problems in a more holistic way and demonstrated more methodical, insightful and integrated approaches to their use of tools. The findings have implications for teaching in design dominated learning environments.

Capability measurement for Inclusive Design

Understanding users' capabilities, needs and expectations is key to the domain of Inclusive Design. Much of the work in the field could be informed and further strengthened by clear, valid and representative data covering the full range of people's capabilities. This article reviews existing data sets and identifies the challenges inherent in measuring capability in a manner that is informative for work in Inclusive Design. The need for a design-relevant capability data set is identified and consideration is given to a variety of capability construct operationalisation issues including questions associated with self-report and performance measures, sampling and the appropriate granularity of measures. The need for further experimental work is identified and a programme of research designed to culminate in the design of a valid and reliable capability survey is described.

Effects and feasibility of a multi-disciplinary orientation program for newly registered cancer patients : design of a randomised controlled trial

Background Diagnosis and treatment of cancer can contribute to psychological distress and anxiety amongst patients. Evidence indicates that information giving can be beneficial in reducing patient anxiety, so oncology specific information may have a major impact on this patient group. This study investigates the effects of an orientation program on levels of anxiety and self-efficacy amongst newly registered cancer patients who are about to undergo chemotherapy and/or radiation therapy in the cancer care centre of a large tertiary Australian hospital. Methods The concept of interventions for orienting new cancer patients needs revisiting due to the dynamic health care system. Historically, most orientation programs at this cancer centre were conducted by one nurse. A randomised controlled trial has been designed to test the effectiveness of an orientation program with bundled interventions; a face-to-face program which includes introduction to the hospital facilities, introduction to the multi-disciplinary team and an overview of treatment side effects and self care strategies. The aim is to orientate patients to the cancer centre and to meet the health care team. We hypothesize that patients who receive this orientation will experience lower levels of anxiety and distress, and a higher level of self-efficacy. Discussion An orientation program is a common health care service provided by cancer care centres for new cancer patients. Such programs aim to give information to patients at the beginning of their encounter at a cancer care centre. It is clear in the literature that interventions that aim to improve self-efficacy in patients may demonstrate potential improvement in health outcomes. Yet, evidence on the effects of orientation programs for cancer patients on self-efficacy remains scarce, particularly with respect to the use of multidisciplinary team members. This paper presents the design of a randomised controlled trial that will evaluate the effects and feasibility of a multidisciplinary orientation program for new cancer patients.

The Brisbane media map : participatory design and authentic learning to link students and industry

The Brisbane Media Map is both an online resource and a tertiary-level authentic learning project. The Brisbane Media Map is an online database which provides a detailed overview of about 600 media industry organisations in Brisbane, Australia. In addition to providing contact details and synopses for each organisation’s profile, the Brisbane Media Map also includes supplementary information on current issues, trends, and individuals in the media and communication industry sectors. This resource is produced and updated annually by final-year undergraduate Media and Communication students. This article introduces the Brisbane Media Map, its functionality and systems design approach, as well as its alignment with key learning infrastructures. It examines authentic learning as the pedagogical framework underpinning the ongoing development work of the resource and highlights some synergies of this framework with participatory design principles. The Brisbane Media Map is a useful example of an authentic learning approach that successfully engages students of non-traditional and non-design areas of study in human-computer interaction, usability, and participatory design activities.

Real Design of a Virtual Landscape : Designing and building a landscape in Second Life

3D Virtual Environments (VE) are real; they exist as digital worlds with the advantage of having none of the constraints of the real world. As such they are the perfect training ground for design students who can create, build and experiment with design solutions without the constraint of real world projects. This paper reports on an educational setting used to explore a model for using VE such as Second Life (SL) developed by Linden Labs in California, as a collaborative environment for design education. A postgraduate landscape architecture learning environment within a collaborative design unit was developed to integrate this model where the primary focus was the application of three-dimensional tools within design, not as a presentation tool, but rather as a design tool. The focus of the unit and its aims and objectives will be outlined before describing the use of SL in the unit. Attention is focused on the collaboration and learning experience before discussing the outcomes, student feedback, future projects using this model and potential for further research. The outcome of this study aims to contribute to current research on teaching and learning design in interactive VE’s. We present a case study of our first application of this model.

Historical timelines : analyzing multimodal text design

The recent focus on literacy in Social Studies has been on linguistic design, particularly that related to the grammar of written and spoken text. When students are expected to produce complex hybridized genres such as timelines, a focus on the teaching and learning of linguistic design is necessary but not sufficient to complete the task. Theorizations of new literacies identify five interrelated meaning making designs for text deconstruction and reproduction: linguistic, spatial, visual, gestural, and audio design. Honing in on the complexity of timelines, this paper casts a lens on the linguistic, visual, spatial, and gestural designs of three pairs of primary school aged Social Studies learners. Drawing on a functional metalanguage, we analyze the linguistic, visual, spatial, and gestural designs of their work. We also offer suggestions of their effect, and from there consider the importance of explicit instruction in text design choices for this Social Studies task. We conclude the analysis by suggesting the foci of explicit instruction for future lessons.

Alcohol and other drugs in the Australian construction industry : A national evaluation and the best way forward

Anecdotal evidence highlights issues of alcohol and other drugs (AODs) and its association with safety risk on construction sites. Information is limited however regarding the prevalence of AODs in the workplace and there is limited evidential guidance regarding how to effectively address it. This research aimed to scientifically evaluate the use of AODs within the Australian construction industry in order to reduce the potential resulting safety and performance impacts and engender a cultural change in the workforce. A national qualitative and quantitative evaluation of the use of AODs was conducted with approximately 500 employees. Results indicate that as in the general population, a proportion of those sampled in the construction sector may be at risk of hazardous alcohol consumption and support the need for evidence-based, tailored responses. This is the first known study to scientifically evaluate the use of AODs and potential workplace safety impacts in the construction sector.

Eco-retrofitting - from managerialism to design

As all environmental problems are caused by human systems of design, sustainability can be seen as a design problem. Given the massive energy and material flows through the built environment, sustainability simply cannot be achieved without the re-design of our urban areas. ‘Eco-retrofitting’, as used here, means modifying buildings and/or urban areas to create net positive social and environmental impacts – both on site and off site. While this has probably not been achieved anywhere as yet, myriad but untapped eco-solutions are already available which could be up-scaled to the urban level. It is now well established that eco-retrofitting buildings and cities with appropriate design technology can pay for itself through lower health costs, productivity increases and resource savings. Good design would also mean happier human and ecological communities at a much lower cost over time. In fact, good design could increase life quality and the life support services of nature while creating sustainable‘economic’growth. The impediments are largely institutional and intellectual, which can be encapsulated in the term ‘managerial’. There are, however, also systems design solutions to the managerial obstacles that seem to be stalling the transition to sustainable systems designs. Given the sustainability imperative, then, why is the adoption of better management systems so slow? The oral presentation will show examples of ways in which built environment design can create environments that not only reduce the ongoing damage of past design, but could theoretically generate net positive social and ecological outcomes over their life cycle. These illustrations show that eco-retrofitting could cost society less than doing nothing - especially given the ongoing renovations of buildings - but for managerial hurdles. The paper outlines on how traditional managerial approaches stand in the way of ‘design for ecosystem services’, and list some management solutions that have long been identified, but are not yet widely adopted. Given the pervasive nature of these impediments and their alternatives, they are presented by way of examples. A sampling of eco-retrofitting solutions are also listed to show that ecoretrofitting is a win-win-win solution that stands ready to be implemented by people having management skills and/or positions of influence.

Daylighting design in the architectural design studio

This paper discusses two different approaches to teaching design and their modes of delivery and reflects upon their successes and failures. Two small groups of third year design students have been given projects focussing on incorporation of daylighting to architectural design in studios having different design themes. In association with the curriculum, the themes were Digital Tools and Sustainability. Although both studios had the topic of daylighting, the aim and methodology used were different. Digital Tool studio’s aim was to teach how to design daylighting by using a digital tool, where as, Sustainability studio aimed at using scale modelling as a tool to learn about daylighting and integrating it into design. Positive results for providing student learning success within the University context were the students’ chance to learn and practice some new skills –using a new tool for designing; integration of the tutors’ extensive research expertise to their teaching practice; and the students’ construction of their own understanding of knowledge in a student-centred educational environment. This environment created a very positive attitude in the form of exchanging ideas and collaboration among the students of Digital Tools students at the discussion forum. Sustainability group students were enthusiastic about designing and testing various proposals. Problems that both studios experienced were mainly related to timing. Synchronizing with other groups of their studios and learning of a new skill on top of an already complicated process of design learning were the setbacks.

Behaviour and design of cold-formed steel compression members at elevated temperatures

Cold-formed steel members have been widely used in residential, industrial and commercial buildings as primary load bearing structural elements and non-load bearing structural elements (partitions) due to their advantages such as higher strength to weight ratio over the other structural materials such as hot-rolled steel, timber and concrete. Cold-formed steel members are often made from thin steel sheets and hence they are more susceptible to various buckling modes. Generally short columns are susceptible to local or distortional buckling while long columns to flexural or flexural-torsional buckling. Fire safety design of building structures is an essential requirement as fire events can cause loss of property and lives. Therefore it is essential to understand the fire performance of light gauge cold-formed steel structures under fire conditions. The buckling behaviour of cold-formed steel compression members under fire conditions is not well investigated yet and hence there is a lack of knowledge on the fire performance of cold-formed steel compression members. Current cold-formed steel design standards do not provide adequate design guidelines for the fire design of cold-formed steel compression members. Therefore a research project based on extensive experimental and numerical studies was undertaken at the Queensland University of Technology to investigate the buckling behaviour of light gauge cold-formed steel compression members under simulated fire conditions. As the first phase of this research, a detailed review was undertaken on the mechanical properties of light gauge cold-formed steels at elevated temperatures and the most reliable predictive models for mechanical properties and stress-strain models based on detailed experimental investigations were identified. Their accuracy was verified experimentally by carrying out a series of tensile coupon tests at ambient and elevated temperatures. As the second phase of this research, local buckling behaviour was investigated based on the experimental and numerical investigations at ambient and elevated temperatures. First a series of 91 local buckling tests was carried out at ambient and elevated temperatures on lipped and unlipped channels made of G250-0.95, G550-0.95, G250-1.95 and G450-1.90 cold-formed steels. Suitable finite element models were then developed to simulate the experimental conditions. These models were converted to ideal finite element models to undertake detailed parametric study. Finally all the ultimate load capacity results for local buckling were compared with the available design methods based on AS/NZS 4600, BS 5950 Part 5, Eurocode 3 Part 1.2 and the direct strength method (DSM), and suitable recommendations were made for the fire design of cold-formed steel compression members subject to local buckling. As the third phase of this research, flexural-torsional buckling behaviour was investigated experimentally and numerically. Two series of 39 flexural-torsional buckling tests were undertaken at ambient and elevated temperatures. The first series consisted 2800 mm long columns of G550-0.95, G250-1.95 and G450-1.90 cold-formed steel lipped channel columns while the second series contained 1800 mm long lipped channel columns of the same steel thickness and strength grades. All the experimental tests were simulated using a suitable finite element model, and the same model was used in a detailed parametric study following validation. Based on the comparison of results from the experimental and parametric studies with the available design methods, suitable design recommendations were made. This thesis presents a detailed description of the experimental and numerical studies undertaken on the mechanical properties and the local and flexural-torsional bucking behaviour of cold-formed steel compression member at ambient and elevated temperatures. It also describes the currently available ambient temperature design methods and their accuracy when used for fire design with appropriately reduced mechanical properties at elevated temperatures. Available fire design methods are also included and their accuracy in predicting the ultimate load capacity at elevated temperatures was investigated. This research has shown that the current ambient temperature design methods are capable of predicting the local and flexural-torsional buckling capacities of cold-formed steel compression members at elevated temperatures with the use of reduced mechanical properties. However, the elevated temperature design method in Eurocode 3 Part 1.2 is overly conservative and hence unsuitable, particularly in the case of flexural-torsional buckling at elevated temperatures.

Fast reconstruction of aerodynamic shapes using evolutionary algorithms and virtual Nash strategies in a CFD design environment

This paper compares the performances of two different optimisation techniques for solving inverse problems; the first one deals with the Hierarchical Asynchronous Parallel Evolutionary Algorithms software (HAPEA) and the second is implemented with a game strategy named Nash-EA. The HAPEA software is based on a hierarchical topology and asynchronous parallel computation. The Nash-EA methodology is introduced as a distributed virtual game and consists of splitting the wing design variables - aerofoil sections - supervised by players optimising their own strategy. The HAPEA and Nash-EA software methodologies are applied to a single objective aerodynamic ONERA M6 wing reconstruction. Numerical results from the two approaches are compared in terms of the quality of model and computational expense and demonstrate the superiority of the distributed Nash-EA methodology in a parallel environment for a similar design quality.

The present via the past : an archaelogical approach to analysing the design and use of a contemporary urban village

This research applies an archaeological lens to an inner-city master planned development in order to investigate the tension between the design of space and the use of space. The chosen case study for this thesis is Kelvin Grove Urban Village (KGUV), located in inner city Brisbane, Australia. The site of this urban village has strong links to the past. KGUV draws on both the history of the place in particular along with more general mythologies of village life in its design and subsequent marketing approaches. The design and marketing approach depends upon notions of an imagined past where life in a place shaped like a traditional village was better and more socially sustainable than modern urban spaces. The appropriation of this urban village concept has been criticised as a shallow marketing ploy. The translation and applicability of the urban village model across time and space is therefore contentious. KGUV was considered both in terms of its design and marketing and in terms of a reading of the actual use of this master planned place. Central to this analysis is the figure of the boundary and related themes of social heterogeneity, inclusion and exclusion. The refraction of history in the site is also an important theme. An interpretive archaeological approach was used overall as a novel method to derive this analysis.