Optimizing potentiometric ionophore and electrode design for environmental on-site control of antibiotic drugs: Application to sulfamethoxazole

Potentiometric sensors are typically unable to carry out on-site monitoring of environmental drug contaminants because of their high limits of detection (LODs). Designing a novel ligand material for the target analyte and managing the composition of the internal reference solution have been the strategies employed here to produce for the first time a potentiometric-based direct reading method for an environmental drug contaminant. This concept has been applied to sulfamethoxazole (SMX), one of the many antibiotics used in aquaculture practices that may occur in environmental waters. The novel ligand has been produced by imprinting SMX on the surface of graphitic carbon nanostructures (CN) < 500 nm. The imprinted carbon nanostructures (ICN) were dispersed in plasticizer and entrapped in a PVC matrix that included (or not) a small amount of a lipophilic additive. The membrane composition was optimized on solid-contact electrodes, allowing near-Nernstian responses down to 5.2 μg/mL and detecting 1.6 μg/mL. The membranes offered good selectivity against most of the ionic compounds in environmental water. The best membrane cocktail was applied on the smaller end of a 1000 μL micropipette tip made of polypropylene. The tip was then filled with inner reference solution containing SMX and chlorate (as interfering compound). The corresponding concentrations were studied for 1 × 10−5 to 1 × 10−10 and 1 × 10−3 to 1 × 10−8 mol/L. The best condition allowed the detection of 5.92 ng/L (or 2.3 × 10−8 mol/L) SMX for a sub-Nernstian slope of −40.3 mV/decade from 5.0 × 10−8 to 2.4 × 10−5 mol/L.

Carnitine tailored Sensors on Surface Molecular Imprinting based on Graphene layers

III Jornadas de Electroquímica e Inovação (Electroquímica e Nanomateriais), na Universidade de Trás-os-Montes e Alto Douro, Vila Real, 16 a 17 de Setembro de 2013

Host-Tailored Sensors for Carnitine Potentiometric Measurements based on Surface Molecular Imprinting

Graduate Student Symposium on Molecular Imprinting 2013, na Queen’s University, Belfast, United Kingdom, 15 a 17 de Agosto de 2013

Carbon key-properties for microcystin adsorption in drinking water treatment: structure or surface chemistry?

Dissertação para Obtenção de Grau de Mestre em Engenharia Química e Bioquímica

Selective synthesis under microwave irradiation of new monomers for potential applications in PDLC films

Dissertation to obtain the degree of master in Bioorganic

Structure-function relationships in a glycosyltransferase, a phosphatase and an oxidoreductase

Dissertation presented to obtain the Ph.D degree in Biochemistry

Participatory mapping in the design process of a spatial data infrastructure SDI: a case study in the Biosphere Reserve Rio Platano (Honduras)

Dissertation submitted in partial fulfillment of the requirements for the Degree of Master of Science in Geospatial Technologies.

The additive effects in matrix dispersed liquid crystals

Dissertation presented at Faculdade de Ciências e Tecnologia from Universidade Nova de Lisboa to obtain the degree of Master in Chemical and Biochemical Engineering

Purification of complex biopharmaceuticals with new processes, advanced analytics and computer-aided process design tools

Dissertação para obtenção do Grau de Mestre em Biotecnologia

Mental health care assessed based on structure, process and outcome : a retrospective cohort study

RESUMO: As doenças mentais são comuns, universais e associadas a uma significativa sobrecarga pessoal, familiar, social e económica. Os Serviços de Saúde Mental devem abordar de forma adequada as necessidades dos pacientes e familiares tanto ao nível clínico como também ao nível social. O presente estudo foi realizado num período de grande transformação nos sistemas de saúde primário e de saúde mental em Portugal, num Departamento de Psiquiatria desenvolvido com base nos princípios da OMS. Os objectivos incluem a caracterização: 1) das Unidades Funcionais do Departamento; 2) dos pacientes internados pela primeira vez no internamento de agudos; 3) da utilização dos serviços nas equipas comunitárias após a alta; e 4) da avaliação de alguns dos indicadores de qualidade do departamento, com recurso ao modelo de Donabedian sobre a articulação entre a Estrutura-Processo-Resultados. Metodologia: Foi escolhido um estudo de coorte retrospectivo. Todos os pacientes internados pela primeira vez entre 2008 e 2010 foram incluídos no estudo. Os seus processos clínicos e a base de dados do hospital onde são registados todos os contactos que estes tiveram com os profissionais de saúde mental foram revistos de forma a obter dados sociodemográficos e clínicos, durante o período do estudo e após a alta. Os instrumentos utilizados foram o WHO-ICMHC (Classificação Internacional de Cuidados de Saúde Mental), para caracterizar o Departamento, o AIESMP (Avaliação Inicial de Enfermagem em Saúde Mental e Psiquiatria) para recolha dos dados sociodemográficos, e o VSSS (Escala de Satisfação com os Serviços de Verona) de forma a avaliar a satisfação dos pacientes em relação aos cuidados recebidos. A análise estatística incluiu a análise descritiva, quantitativa e qualitativa dos dados. Resultados: As Unidades Funcionais do Departamento revelaram níveis elevados de articulação e consistência com as necessidades de cuidados psiquiátricos e reabilitação psicossocial dos pacientes. Os 543 pacientes admitidos pela primeira vez eram maioritariamente (56.9%) mulheres, caucasianas (81.2%), com diagnóstico de perturbações do humor (66.3%), internadas voluntariamente (59.7%), e uma idade média de 45.1 anos. Estas eram significativamente mais velhas, mais frequentemente empregadas, casadas/coabitar e tinham uma prevalência mais elevada de perturbações do humor, comparativamente aos homens. O internamento compulsivo era mais significativo nos homens (54.7%). A taxa de abandono no pós-alta (4.2%) e a taxa de reinternamentos (2.9%) na quinzena após a alta revelaram-se inferiores aos padrões na literatura internacional. De forma global, a satisfação dos pacientes com os cuidados de saúde mental foi positiva. Conclusões: Os cuidados prestados mostraram-se eficazes, adaptados e baseados nas necessidades e problemas específicos dos pacientes. A continuidade e a abrangência de cuidados foram difundidos e mantidos ao longo do processo de cuidados. Este Departamento pode ser considerado um exemplo de como proporcionar tratamento digno e eficiente, e uma referência para futuros serviços de psiquiatria.-------------- ABSTRACT: Mental health disorders are common, universal, and associated with heavy personal, family, social and economic burden. Mental health services should be aimed at adequately addressing patients’ and families’ needs at clinical and social level. The current study was carried out at a time of great transformation in the health and mental health systems in Portugal, in a Psychiatric Department developed taking in consideration the WHO principles. The objectives included characterizing: 1) the Psychiatric Department’s different units; 2) the patients admitted for the first time to the inpatient unit; 3) their use of community mental health services after discharge; and 4) assessing some of the department’s quality indicators, with resource to Donabedian’s Structure-Process-Outcome model. Methodology: A retrospective cohort design was chosen. All the firstly admitted patients in the period between 2008 and 2010 were included in the study. Their clinical records and the hospital’s database which registers all of the contacts the patients had with the mental health professionals during the study period, were reviewed to retrieve sociodemographic and clinical data and information on follow-up. The instruments used were the WHO International Classification of Mental Health Care (ICMHC) to characterize the department, the Initial Nurses’ Assessment in Mental Health and Psychiatry (AIESMP) for patients’ sociodemographic data, and the Verona Service Satisfaction Scale (VSSS) to assess patients’ satisfaction with care received. Statistical analysis included descriptive, quantitative and qualitative analysis of the data. Results: The Department’s Functional units revealed high levels of articulation, and were consistent with patients’ needs for psychiatric care and psychosocial rehabilitation. The 543 patients firstly admitted were mainly (56.9%) female, Caucasian (81.2%), diagnosed with mood disorders (66.3%), voluntarily admitted (59.7%), and with a mean age of 45.1 years. Female patients were significantly older, more frequently employed, married/cohabiting and had a higher prevalence of mood disorders when compared to males. Involuntary admission was more significant in males (54.7%). Dropout rates during follow-up (4.2%) and readmission rates (2.9%) in the fortnight following discharge were lower than standards in international literature. Overall patients’ satisfaction with mental health care was positive. Conclusions: The care delivered was effective, adapted and based on the patients’ specific needs and problems. Continuity and comprehensiveness of care was endorsed and maintained throughout the care process. This department may be considered an example of both humane and effective treatment, and a reference for future psychiatric care.

Design and characterization of Chitin- Glucan polymeric structures for wound dressing materials

The main objective of this work was the development of polymeric structures, gel and films, generated from the dissolution of the Chitin-Glucan Complex (CGC) in biocompatible ionic liquids for biomedical applications. Similar as chitin, CGC is only soluble in some special solvents which are toxic and corrosive. Due to this fact and the urgent development of biomedical applications, the need to use biocompatible ionic liquids to dissolve the CGC is indispensable. For the dissolution of CGC, the biocompatible ionic liquid used was Choline acetate. Two different CGC’s, KiOnutrime from KitoZyme and biologically produced CGC from Faculdade de Ciencias e Tecnologia (FCT) - Universidade Nova de Lisboa, were characterized in order to develop biocompatible wound dressing materials. The similar result is shown in term of the ratio of chitin:glucan, which is 1:1.72 for CGC-FCT and 1:1.69 for CGC-Commercial. For the analysis of metal element content, water and inorganic salts content and protein content, both polymers showed some discrepancies, where the content in CGC-FCT is always higher compared to the commercial one. The different characterization results between CGC-FCT and CGC-Commercial could be addressed to differences in the purification method, and the difference of its original strain yeast, whereas CGC-FCT is derived from P.pastoris and the commercial CGC is from A.niger. This work also investigated the effect of biopolymers, temperature dissolution, non-solvent composition on the characteristics of generated polymeric structure with biocompatible ionic liquid. The films were prepared by casting a polymer mixture, immersion in a non-solvent, followed by drying at ambient temperature. Three different non-solvents were tested in phase inversion method, i.e. water, methanol, and glycerol. The results indicate that the composition of non-solvent in the coagulation bath has great influence in generated polymeric structure. Water was found to be the best coagulant for producing a CGC polymeric film structure. The characterizations that have been done include the analysis of viscosity and viscoelasticity measurement, as well as sugar composition in the membrane and total sugar that was released during the phase inversion method. The rheology test showed that both polymer mixtures exhibit a non- Newtonian shear thinning behaviour. Where the viscosity and viscoelasticity test reveal that CGCFCT mixture has a typical behaviour of a viscous solution with entangled polymer chains and CGCCommercial mixture has true gel behaviour. The experimental results show us that the generated CGC solution from choline acetate could be used to develop both polymeric film structure and gel. The generated structures are thermally stable at 100° C, and are hydrophilic. The produced films have dense structure and mechanical stabilities against puncture up to 60 kPa.

Design, implementation, and performance of a distributed and scalable sensor system for critical distance measurements in the CMS detector at LHC

The “CMS Safety Closing Sensors System” (SCSS, or CSS for brevity) is a remote monitoring system design to control safety clearance and tight mechanical movements of parts of the CMS detector, especially during CMS assembly phases. We present the different systems that makes SCSS: its sensor technologies, the readout system, the data acquisition and control software. We also report on calibration and installation details, which determine the resolution and limits of the system. We present as well our experience from the operation of the system and the analysis of the data collected since 2008. Special emphasis is given to study positioning reproducibility during detector assembly and understanding how the magnetic fields influence the detector structure.

Electro-Optical/Infrared sensor turret integration on an aircraft - structural im-pact on LOCKHEED MARTIN C-130H and design methodology

The growing need to patrol and survey large maritime and terrestrial areas increased the need to integrate external sensors on aircraft in order to accomplish those patrols at increasingly higher altitudes, longer range and not depending upon vehicle type. The main focus of this work is to elaborate a practical, simple, effective and efficient methodology for the aircraft modification procedure resulting from the integration of an Elec-tro-Optical/Infra-Red (EO/IR) turret through a support structure. The importance of the devel-opment of a good methodology relies on the correct management of project variables as time, available resources and project complexity. The key is to deliver a proper tool for a project de-sign team that will be used to create a solution that fulfils all technical, non-technical and certi-fication requirements present in this field of transportation. The created methodology is inde-pendent of two main inputs: sensor model and aircraft model definition, and therefore it is in-tended to deliver the results for different projects besides the one that was presented in this work as a case study. This particular case study presents the development of a structure support for FLIR STAR SAPHIRE III turret integration on the front lower fuselage bulkhead (radome) of the LOCKHEED MARTIN C-130 H. Development of the case study focuses on the study of local structural analysis through the use of Finite Element Method (FEM). Development of this Dissertation resulted in a cooperation between Faculty of Science and Technology - Universidade Nova de Lisboa and the company OGMA - Indústria Aeronáutica de Portugal

Orthogonal models, structure crossing, nesting and inference

We intend to study the algebraic structure of the simple orthogonal models to use them, through binary operations as building blocks in the construction of more complex orthogonal models. We start by presenting some matrix results considering Commutative Jordan Algebras of symmetric matrices, CJAs. Next, we use these results to study the algebraic structure of orthogonal models, obtained by crossing and nesting simpler ones. Then, we study the normal models with OBS, which can also be orthogonal models. We intend to study normal models with OBS (Orthogonal Block Structure), NOBS (Normal Orthogonal Block Structure), obtaining condition for having complete and suffcient statistics, having UMVUE, is unbiased estimators with minimal covariance matrices whatever the variance components. Lastly, see ([Pereira et al. (2014)]), we study the algebraic structure of orthogonal models, mixed models whose variance covariance matrices are all positive semi definite, linear combinations of known orthogonal pairwise orthogonal projection matrices, OPOPM, and whose least square estimators, LSE, of estimable vectors are best linear unbiased estimator, BLUE, whatever the variance components, so they are uniformly BLUE, UBLUE. From the results of the algebraic structure we will get explicit expressions for the LSE of these models.

Design of bio-inspired ionic liquids for protein stabilisation

Ionic Liquids (ILs) consist in organic salts that are liquid at/or near room temperature. Since ILs are entirely composed of ions, the formation of ion pairs is expected to be one essential feature for describing solvation in ILs. In recent years, protein - ionic liquid (P-IL) interactions have been the subject of intensive studies mainly because of their capability to promote folding/unfolding of proteins. However, the ion pairs and their lifetimes in ILs in P-IL thematic is dismissed, since the action of ILs is therefore the result of a subtle equilibrium between anion-cation interaction, ion-solvent and ion-protein interaction. The work developed in this thesis innovates in this thematic, once the design of ILs for protein stabilisation was bio-inspired in the high concentration of organic charged metabolites found in cell milieu. Although this perception is overlooked, those combined concentrations have been estimated to be ~300 mM among the macromolecules at concentrations exceeding 300 g/L (macromolecular crowding) and transient ion-pair can naturally occur with a potential specific biological role. Hence the main objective of this work is to develop new bio-ILs with a detectable ion-pair and understand its effects on protein structure and stability, under crowding environment, using advanced NMR techniques and calorimetric techniques. The choline-glutamate ([Ch][Glu]) IL was synthesized and characterized. The ion-pair was detected in water solutions using mainly the selective NOE NMR technique. Through the same technique, it was possible to detect a similar ion-pair promotion under synthetic and natural crowding environments. Using NMR spectroscopy (protein diffusion, HSQC experiments, and hydrogen-deuterium exchange) and differential scanning calorimetry (DSC), the model protein GB1 (production and purification in isotopic enrichment media) it was studied in the presence of [Ch][Glu] under macromolecular crowding conditions (PEG, BSA, lysozyme). Under dilute condition, it is possible to assert that the [Ch][Glu] induces a preferential hydration by weak and non-specific interactions, which leads to a significant stabilisation. On the other hand, under crowding environment, the [Ch][Glu] ion pair is promoted, destabilising the protein by favourable weak hydrophobic interactions , which disrupt the hydration layer of the protein. However, this capability can mitigates the effect of protein crowders. Overall, this work explored the ion-pair existence and its consequences on proteins in conditions similar to cell milieu. In this way, the charged metabolites found in cell can be understood as key for protein stabilisation.