Analysis of sandflies (Diptera: Psychodidae) in Barra do Garças, State of Mato Grosso, Brazil, and the influence of environmental variables on the vector density of Lutzomyia longipalpis (Lutz & Neiva, 1912)

INTRODUCTION: Leishmaniasis is an infectious and parasitic zoonotic, non-contagious, vector-borne disease caused by protozoa of the genus Leishmania. In Brazil, the major vector of Leishmania (Leishmania) infantum chagasi (Cunha & Chagas, 1934) is Lutzomyia longipalpis. Barra do Garças, State of Mato Grosso, was designated as a priority area by the Brazilian Ministry of Health for american visceral leishmaniasis, and it is important to identify the vector species present in this municipality. Our objective was to raise sandflies and study the influence of environmental variables on the vector density of Lutzomyia longipalpis. METHODS: We performed entomological monitoring in 3 districts using Centers for Disease Control and Prevention (CDC) light traps and recorded human cases of american visceral leishmaniasis in the city. We calculated the relative frequency and richness of sandflies and applied a transfer function model to the vector density correlate with relative humidity. RESULTS: The sandfly population was composed of 2 genera and 27 species, totaling 8,097 individuals. Monitoring identified Lutzomyia longipalpis (44%), followed by Lutzomyia lenti (18.9%), Lutzomyia whitmani (13.9%), Lutzomyia carmelinoi (9.1%), Lutzomyia evandroi (5.1%), Lutzomyia termitophila (3.3%), Lutzomyia sordellii (1.9%), and 20 other species (<4%). The male:female ratio was 3.5:1. We observed high species diversity (Dα = 6.65). Lutzomyia longipalpis showed occurrence peaks during the rainy season; there was a temporal correlation with humidity, but not with frequency or temperature. CONCLUSIONS: The presence of Lutzomyia longipalpis in the urban area of Barra do Garças underscores the changing disease profile, which was previously restricted to the wild environment.

Normal bone density in male pseudohermaphroditism due to 5alpha- reductase 2 deficiency

Bone is an androgen-dependent tissue, but it is not clear whether the androgen action in bone depends on testosterone or on dihydrotestosterone. Patients with 5alpha-reductase 2 deficiency present normal levels of testosterone and low levels of dihydrotestosterone, providing an in vivo human model for the analysis of the effect of testosterone on bone. OBJECTIVE: To analyze bone mineral density in 4 adult patients with male pseudohermaphroditism due to 5alpha-reductase 2 deficiency. RESULTS: Three patients presented normal bone mineral density of the lumbar column (L1-L4) and femur neck, and the other patient presented a slight osteopenia in the lumbar column. CONCLUSION: Patients with dihydrotestosterone deficiency present normal bone mineral density, suggesting that dihydrotestosterone is not the main androgen acting in bone.

Distribution of Atta (Hymenoptera - Formicidae) in "terra-firme" rain forest of Central Amazonia: density, species composition and preliminary results on effects of forest fragmentation

One hundred and fourteen hectares of a "terra-fiirme" rain forest 70 km north of Manaus, Amazonas, Brazil, were surveyed for leaf-cutting ant colonies (Atta spp). One half of this area was in isolated forest fragments (surrounded by pastures or second growth) of two sizes: 1 and 10 ha. The other half was in non-isolated fragments (connected to a large parch of forest) of the same sizes. Only two species occured in this forest: Atta sexdens sexdens L. and A. cepfhalotes L. The first was the most abundant species with a mean density of 0.35 colonies per ha. The mean density of A. cephalotes colonies was 0.03 per ha. The density of colonies was not significantly different between the isolated fragments and the continuous forest. Furthermore, the species composition did not change with isolation. However, pre-isolation data and long term monitoring are necessary to conclude that the isolation of a forest fragment has no effect upon Atta colonies. The non-uniform spatial distribution of Atta colonics within the "terra-firme" forest must be taken into account when selecting conservation areas in the Amazon, in order to preserve this important group of ants together with their native habitat.

Electrokinetic treatment of environmental matrices. Contaminants removal and phosphorus recovery

There is a need to develop viable techniques for removal and recovery organic and inorganic compounds from environmental matrices, due to their ecotoxicity, regulatory obligations or potential supplies as secondary materials. In this dissertation, electro –removal and –recovery techniques were applied to five different contaminated environmental matrices aiming phosphorus (P) recovery and/or contaminants removal. In a first phase, the electrokinetic process (EK) was carried out in soils for (i) metalloids and (ii) organic contaminants (OCs) removal. In the case of As and Sb mine contaminated soil, the EK process was additionally coupled with phytotechnologies. In a second phase, the electrodialytic process (ED) was applied to wastes aiming P recovery and simultaneous removal of (iii) toxins from membrane concentrate, (iv) heavy metals from sewage sludge ash (SSA), and (v) OCs from sewage sludge (SS). EK enhanced phytoremediation showed to be viable for the remediation of soils contaminated with metalloids, as although remediation was low, it combines advantages of both technologies while allowing site management. EK also proved to be an effective remediation technology for the removal and degradation of emerging OCs from two types of soil. Aiming P recovery and contaminants removal, different ED cell set-ups were tested. For the membrane concentrates, the best P recovery was achieved in a three compartment (3c) cell, but the highest toxin removal was obtained in a two compartment (2c) cell, placing the matrix in the cathode end. In the case of SSA the best approach for simultaneous P recovery and heavy metals removal was to use a 2c-cell placing the matrix in the anode end. However, for simultaneous P recovery and OCs removal, SS should be placed in the cathode end, in a 2c-cell. Overall, the data support that the selection of the cell design should be done case-by-case.

Engineering bio-based polymers using alternative solvents and processes

The work presented in this thesis explores novel routes for the processing of bio-based polymers, developing a sustainable approach based on the use of alternative solvents such as supercritical carbon dioxide (scCO2), ionic liquids (ILs) and deep eutectic solvents (DES). The feasibility to produce polymeric foams via supercritical fluid (SCF) foaming, combined with these solvents was assessed, in order to replace conventional foaming techniques that use toxic and harmful solvents. A polymer processing methodology is presented, based on SCF foaming and using scCO2 as a foaming agent. The SCF foaming of different starch based polymeric blends was performed, namely starch/poly(lactic acid) (SPLA) and starch/poly(ε-caprolactone) (SPCL). The foaming process is based on the fact that CO2 molecules can dissolve in the polymer, changing their mechanical properties and after suitable depressurization, are able to create a foamed (porous) material. In these polymer blends, CO2 presents limited solubility and in order to enhance the foaming effect, two different imidazolium based ILs (IBILs) were combined with this process, by doping the blends with IL. The use of ILs proved useful and improved the foaming effect in these starch-based polymer blends. Infrared spectroscopy (FTIR-ATR) proved the existence of interactions between the polymer blend SPLA and ILs, which in turn diminish the forces that hold the polymeric structure. This is directly related with the ability of ILs to dissolve more CO2. This is also clear from the sorption experiments results, where the obtained apparent sorption coefficients in presence of IL are higher compared to the ones of the blend SPLA without IL. The doping of SPCL with ILs was also performed. The foaming of the blend was achieved and resulted in porous materials with conductivity values close to the ones of pure ILs. This can open doors to applications as self-supported conductive materials. A different type of solvents were also used in the previously presented processing method. If different applications of the bio-based polymers are envisaged, replacing ILs must be considered, especially due to the poor sustainability of some ILs and the fact that there is not a well-established toxicity profile. In this work natural DES – NADES – were the solvents of choice. They present some advantages relatively to ILs since they are easy to produce, cheaper, biodegradable and often biocompatible, mainly due to the fact that they are composed of primary metabolites such as sugars, carboxylic acids and amino-acids. NADES were prepared and their physicochemical properties were assessed, namely the thermal behavior, conductivity, density, viscosity and polarity. With this study, it became clear that these properties can vary with the composition of NADES, as well as with their initial water content. The use of NADES in the SCF foaming of SPCL, acting as foaming agent, was also performed and proved successful. The SPCL structure obtained after SCF foaming presented enhanced characteristics (such as porosity) when compared with the ones obtained using ILs as foaming enhancers. DES constituted by therapeutic compounds (THEDES) were also prepared. The combination of choline chloride-mandelic acid, and menthol-ibuprofen, resulted in THEDES with thermal behavior very distinct from the one of their components. The foaming of SPCL with THEDES was successful, and the impregnation of THEDES in SPCL matrices via SCF foaming was successful, and a controlled release system was obtained in the case of menthol-ibuprofen THEDES.

Wood density of trees in black water floodplains of Rio Jaú National Park, Amazonia, Brazil

The Jaú National Park is the largest protected forested area in the world. The Vitória Amazônica Foundation is working towards understanding its ecosystem, to which this paper contributes. Wood density was analysed in 27 common tree species growing in the blackwater flood-plains of the Rio Jaú, an affluent of the Rio Negro (Amazonia, Brazil). Wood was sampled with an increment borer. Mean wood density of the analysed species ranged from 0.35 to 0.87 g cm-3. The mean of all sampled species was 0.67 g cm-3 (st. dev. 0.13). Lowest density was found for Hevea spruceana with 0.32 g cm-3 and highest for Crudia amazonica with 0.9 g cm-3.

Tensile and bond characterization of natural fibers embeeded in inorganic matrices

Innovative composite materials made of continuous fibers embedded in mortar matrices have been recently received attention for externally bonded reinforcement of masonry structures. In this regards, application of natural fibers for strengthening of the repair mortars is attractive due to their low specific weight, sustainability and recycability. This paper presents experimental characterization of tensile and pull-out behavior of natural fibers embedded in two different mortar-based matrices. A lime-based and a geopolymeric-based mortar are used as sustainable and innovative matrices. The obtained experimental results and observations are presented and discussed.

Heliconia acuminata reproductive success is independent of local floral density

Reproductive plants in tropical forests are patchily distributed, with some in large aggregations of reproductive consepecifics while others are relatively isolated. This variation in floral density is hypothesized to have a major effect on plant reproductive success, since individuals in higher density neighborhoods can attract more or higher quality pollinators. We experimentally tested this hypothesis with populations of the understory herb Heliconia acuminata in central Amazonia. We created replicated plots in which reproductive plant density spanned the range of naturally occurring floral neighborhood size, then measured three surrogates of plant fitness in focal plants in each array. There was no significant difference between any of the three floral neighborhood treatments in total seed production, fruit set, or the number of seeds produced per fruit. Pollinator visitation rates to plants in all treatments were extremely low, with many plants not visited at all during the observation period. This could be because H. acuminata's hummingbird pollinators are unable to find the widely scattered reproductive plants, however this hypothesis appears unlikely. Instead, natural flowering plant densities may simply be below the threshold value at which neighborhood effects become important, even in "high-density" aggregations. Nutrient limitation, selective fruit abortion, and reproduction via male rather than female function may also be playing a role. We argue the absence of neighborhood effects may be a general phenomenon in central Amazonian forests, though additional experiments with other plant-pollinator systems are needed to determine the extent to which this hypothesis is supported.

Desenvolvimento de estruturas fibrosas com comportamento auxético

Tese de Doutoramento Engenharia Têxtil

Effects of forest structure components on the occurence, group size and density of groups of bare-face tamarin (Saguinus bicolor - primates: Callitrichinae) in Central Amazonia

This study analyzed the influence of forest structural components on the occurence, size and density of groups of Bare-face Tamarin (Saguinus bicolor) - the most threatened species in the Amazon - and produced the first map of distribution of groups in large-scale spatial within the area of continuous forest. Population censuses were conducted between November 2002 and July 2003, covering 6400 hectares in the Ducke Reserve, Manaus-AM, Brazil. Groups of S. bicolor were recorded 41 times accordingly distributed in the environments: plateau (20); slopes (12); and lowlands (09). The mean group size was 4.8 indiv./group, and ranged from 2 to 11 individuals. In the sites where the groups were recorded, and in an equivalent number of sites where no tamarins were found located at least 500 m from those where they had been recorded, we placed 50 m x 50 m plots to record the following forest structural components: abundance of trees; abundance of lianas; abundance of fruiting trees and lianas; abundance of snags; abundance of logs; percentage of canopy opening; leaf litter depth; and altitude. Bare-face Tamarin more often uses areas with lower abundance of forest logs, smaller canopy opening and with higher abundance of snags, areas in the forest with smaller canopy opening present higher density of S. bicolor groups. Apparently this species does not use the forest in a random way, and may select areas for its daily activities depending on the micro-environmental heterogeneity produced by the forest structural components.

Dispersion of fillers in viscoelastic polymer matrices using Eulerian-Lagrangian approaches

Understanding the behavior of c omplex composite materials using mixing procedures is fundamental in several industrial processes. For instance, polymer composites are usually manufactured using dispersion of fillers in polymer melt matrices. The success of the filler dispersion depends both on the complex flow patterns generated and on the polymer melt rheological behavior. Consequently, the availability of a numerical tool that allow to model both fluid and particle would be very useful to increase the process insight. Nowadays there ar e computational tools that allow modeling the behavior of filled systems, taking into account both the behavior of the fluid (Computational Rheology) and the particles (Discrete Element Method). One example is the DPMFoam solver of the OpenFOAM ® framework where the averaged volume fraction momentum and mass conservation equations are used to describe the fluid (continuous phase) rheology, and the Newton’s second law of motion is used to compute the particles (discrete phase) movement. In this work the refer red solver is extended to take into account the elasticity of the polymer melts for the continuous phase. The solver capabilities will be illustrated by studying the effect of the fluid rheology on the filler dispersion, taking into account different fluid types (generalized Newtonian or viscoelastic) and particles volume fraction and size. The results obtained are used to evaluate the relevance of considering the fluid complex rheology for the prediction of the composites morphology

Understanding the dispersion of fillers in polymer matrices

Understanding the mixing process of complex composite materials is fundamental in several industrial processes. For instance, the dispersion of fillers in polymer melt matrices is commonly employed to manufacture polymer composites, using a twin-screw extruder. The effectiveness of the filler dispersion depends not only on the complex flow patterns generated, but also on the polymer melt rheological behavior. Therefore, the availability of a numerical tool able to predict mixing, taking into account both fluid and particles phases would be very useful to increase the process insight, and thus provide useful guidelines for its optimization. In this work, a new Eulerian-Lagrangian numerical solver is developed OpenFOAM® computational library, and used to better understand the mechanisms determining the dispersion of fillers in polymer matrices. Particular attention will be given to the effect of the rheological model used to represent the fluid behavior, on the level of dispersion obtained. For the Eulerian phase the averaged volume fraction governing equations (conservation of mass and linear momentum) are used to describe the fluid behavior. In the case of the Lagrangian phase, Newton’s second law of motion is used to compute the particles trajectories and velocity. To study the effect of fluid behavior on the filler dispersion, several systems are modeled considering different fluid types (generalized Newtonian or viscoelastic) and particles volume fraction and size. The results obtained are used to correlate the fluid and particle characteristics on the effectiveness of mixing and morphology obtained.

Outcrossing rate of Couratari multiflora (J.Smith) Eyma (Lecythidaceae), a low-density tropical tree species from a central Amazonian rainforest

A multilocus mixed-mating model was used to evaluate the mating system of a population of Couratari multiflora, an emergent tree species found in low densities (1 individual/10 ha) in lowland forests of central Amazonia. We surveyed and observed phenologically 41 trees in an area of 400 ha. From these, only four mother trees were analyzed here because few of them set fruits, which also suffered high predation. No difference was observed between the population multilocus outcrossing rate (t mp = 0.953 ± 0.040) and the average single locus rate (t sp = 0.968 ± 0.132). The four mother trees were highly outcrossed (t m ~ 1). Two out of five loci showed departures from the Hardy-Weinberg Equilibrium (HWE) expectations, and the same results occurred with the mixed-mating model. Besides the low number of trees analyzed, the proportion of loci in HWE suggests random mating in the population. However, the pollen pool was heterogeneous among families, probably due to both the small sample number and the flowering of trees at different times of the flowering season. Reproductive phenology of the population and the results presented here suggest, at least for part of the population, a long-distance pollen movement, around 1,000 m.

Density, size and distribution of stomata in 35 rainforest tree species in Central Amazonia

Stomata are turgor-operated valves that control water loss and CO2 uptake during photosynthesis, and thereby water relation and plant biomass accumulation is closely related to stomatal functioning. The aims of this work were to document how stomata are distributed on the leaf surface and to determine if there is any significant variation in stomatal characteristics among Amazonian tree species, and finally to study the relationship between stomatal density (S D) and tree height. Thirty five trees (>17 m tall) of different species were selected. Stomatal type, density (S D), size (S S) and stomatal distribution on the leaf surface were determined using nail polish imprints taken from both leaf surfaces. Irrespective of tree species, stomata were located only on the abaxial surface (hypostomaty), with large variation in both S D and S S among species. S D ranged from 110 mm-2 in Neea altissima to 846 mm-2 in Qualea acuminata. However, in most species S D ranges between 271 and 543 mm-2, with a negative relationship between S D and S S. We also found a positive relationship between S D and tree height (r² = 0.14, p < 0.01), but no correlation was found between S D and leaf thickness. The most common stomatal type was anomocytic (37%), followed by paracytic (26%) and anisocytic (11%). We conclude that in Amazonian tree species, stomatal distribution on the leaf surface is a response most likely dependent on the genetic background of every species, rather than a reaction to environmental changes, and that somehow S D is influenced by environmental factors dependent on tree height.

On simple bounds for eigenvalues of symmetric tridiagonal matrices

How much can be said about the location of the eigenvalues of a symmetric tridiagonal matrix just by looking at its diagonal entries? We use classical results on the eigenvalues of symmetric matrices to show that the diagonal entries are bounds for some of the eigenvalues regardless of the size of the off-diagonal entries. Numerical examples are given to illustrate that our arithmetic-free technique delivers useful information on the location of the eigenvalues.