Polarization-dependent pulse compression in an argon-filled cell through filamentation

Pulse compression through filamentation in an argon-filled cell was experimentally demonstrated by using circularly and linearly polarized pulses. A 53 fs circularly polarized pulse was successfully compressed to 15 fs. By using circularly polarized pulse input, the broadened spectrum was much wider and the incident energy in the gas cell can be increased by more than 3/2 times. Much shorter pulse could be compressed by using circularly polarized pulse input. [GRAPHICS] The temporal profile of the compressed pulse (C) 2008 by Astro Ltd. Published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA.

Influence of target thickness on the generation of high-density ion bunches by ultrashort circularly polarized laser pulses

Ion acceleration by ultrashort circularly polarized laser pulse in a solid-density target is investigated using two-dimensional particle-in-cell simulation. The ions are accelerated and compressed by the continuously extending space-charge field created by the evacuation and compression of the target electrons by the laser light pressure. For a sufficiently thin target, the accelerated and compressed ions can reach and exit from the rear surface as a high-density high-energy ion bunch. The peak ion energy depends on the target thickness and reaches maximum when the compressed ion layer can just reach the rear target surface. The compressed ion layer exhibits lateral striation which can be suppressed by using a sharp-rising laser pulse. (c) 2008 American Institute of Physics.

Spectral analysis and control to obtain sub-5 fs pulses by femtosecond filamentation

A spectral-filter method is numerically demonstrated to obtain sub-5 fs pulses by using femtosecond filamentation in fused silica. Instead of employing spectral phase compensation, by properly employing a high-pass filter to select the broadened high-frequency spectra that are located almost in phase in the tailing edge of the self-compressed pulses owing to self-steepening, as short as single-cycle pulses can be obtained. For instance, for an input pulse with a duration of 50 fs and energy 2.2 mu J, the minimum pulse duration can reach to similar to 4 fs (about 1.5 cycles) by applying a proper spectral filter. (C) 2008 Optical Society of America

Generation of sub-5 fs pulses through cascade of filamentation and hollow fiber compression

A pulse-compression scheme based on cascade of filamentation and hollow fiber has been demonstrated, Pulses with duration of sub-5 fs and energy of 0.2 mJ near 800 nm have been generated by compressing the similar to 40 fs pulses from a commercial laser system. This method is promising to generate near monocycle high energy pulses. [GRAPHICS] Measured autocorrelation curve of the final compressed pulses with duration of sub-5 fs (black solid) and the simulated autocorrelation curve of 4.6 fs pulse near 800 rim (red dash) (C) 2008 by Astro Ltd. Published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA

The propagation and deposition of fast muons in dense DT mixture

The propagation of the fast muon population mainly due to collisional effect in a dense deuterium-tritium (DT for short) mixture is investigated and analysed within the framework of the relativistic Fokker-Planck equation. Without the approximation that the muons propagate straightly in the DT mixture, the muon penetration length, the straggling length, and the mean transverse dispersion radius are calculated for different initial energies, and especially for different densities of the densely compressed DT mixture in our suggested muon-driven fast ignition (FI). Unlike laser-driven FI requiring super-high temperature, muons can catalyze DT fusion at lower temperatures and may generate an ignition sparkle before the self-heating fusion follows. Our calculation is important for the feasibility and the experimental study of muon-driven FI.

1kHz-0．1TW高效率钛宝石激光放大器

介绍了一种高重复频率掺钛蓝宝石飞秒激光多通高效率放大系统．在抽运功率为23W，入射功率为660mW时，获得7．2W的放大输出，放大效率达30％．经压缩器压缩后，获得单脉冲能量4．5mJ，脉冲宽度为38fs，重复频率为1kHz，峰值功率大于0．1TW的超短超强激光脉冲．

Direct acceleration of solid-density plasma bunch by ultraintense laser

The interaction of a petawatt laser with a small solid-density plasma bunch is studied by particle-in-cell simulation. It is shown that when irradiated by a laser of intensity >10(21) W/cm(2), a dense plasma bunch of micrometer size can be efficiently accelerated. The kinetic energy of the ions in the high-density region of the plasma bunch can exceed ten MeV at a density in the 10(23)-cm(-3) level. Having a flux density orders of magnitude higher than that of the traditional charged-particle pulses, the laser-accelerated plasma bunch can have a wide range of applications. In particular, such a dense energetic plasma bunch impinging on the compressed fuel in inertial fusion can significantly enhance the nuclear-reaction cross section and is thus a promising alternative for fast ignition.

Optimization of single attosecond x-ray pulses by genetic algorithm control of the chirp and initial phase of 5 fs laser pulses

We show that the peak intensity of single attosecond x-ray pulses is enhanced by 1 or 2 orders of magnitude, the pulse duration is greatly compressed, and the optimal propagation distance is shortened by genetic algorithm optimization of the chirp and initial phase of 5 fs laser pulses. However, as the laser intensity increases, more efficient nonadiabatic self-phase matching can lead to a dramatically enhanced harmonic yield, and the efficiency of optimization decreases in the enhancement and compression of the generated attosecond pulses. (c) 2006 Optical Society of America.

Optimum hot electron production with low-density foams for laser fusion by fast ignition

We propose a foam cone-in-shell target design aiming at optimum hot electron production for the fast ignition. A thin low-density foam is proposed to cover the inner tip of a gold cone inserted in a fuel shell. An intense laser is then focused on the foam to generate hot electrons for the fast ignition. Element experiments demonstrate increased laser energy coupling efficiency into hot electrons without increasing the electron temperature and beam divergence with foam coated targets in comparison with solid targets. This may enhance the laser energy deposition in the compressed fuel plasma.

Techniques for strength measurement at high pressures and strain-rates using transverse waves

The study of the strength of a material is relevant to a variety of applications including automobile collisions, armor penetration and inertial confinement fusion. Although dynamic behavior of materials at high pressures and strain-rates has been studied extensively using plate impact experiments, the results provide measurements in one direction only. Material behavior that is dependent on strength is unaccounted for. The research in this study proposes two novel configurations to mitigate this problem.

The first configuration introduced is the oblique wedge experiment, which is comprised of a driver material, an angled target of interest and a backing material used to measure in-situ velocities. Upon impact, a shock wave is generated in the driver material. As the shock encounters the angled target, it is reflected back into the driver and transmitted into the target. Due to the angle of obliquity of the incident wave, a transverse wave is generated that allows the target to be subjected to shear while being compressed by the initial longitudinal shock such that the material does not slip. Using numerical simulations, this study shows that a variety of oblique wedge configurations can be used to study the shear response of materials and this can be extended to strength measurement as well. Experiments were performed on an oblique wedge setup with a copper impactor, polymethylmethacrylate driver, aluminum 6061-t6 target, and a lithium fluoride window. Particle velocities were measured using laser interferometry and results agree well with the simulations.

The second novel configuration is the y-cut quartz sandwich design, which uses the anisotropic properties of y-cut quartz to generate a shear wave that is transmitted into a thin sample. By using an anvil material to back the thin sample, particle velocities measured at the rear surface of the backing plate can be implemented to calculate the shear stress in the material and subsequently the strength. Numerical simulations were conducted to show that this configuration has the ability to measure the strength for a variety of materials.

Pulse compression by filamentation in argon with an acoustic optical programmable dispersive filter for predispersion compensation

We have experimentally demonstrated pulses 0.4 mJ in duration smaller than 12 fs; with an excellent spatial beam profile by self-guided propagation in argon. The original 52 fs pulses from the chirped pulsed amplification laser system are first precompressed to 32 fs by inserting an acoustic optical programmable dispersive filter instrument into the laser system for spectrum reshaping and dispersion compensation, and the pulse spectrum is subsequently broadened by filamentation in an argon cell. By using chirped mirrors for post-dispersion compensation, the pulses are successfully compressed to smaller than 12 fs.

Pulse self-compression in normally dispersive bulk media

We experimentally demonstrate that high-power femtosecond pulses can be compressed during the nonlinear propagation in the normally dispersive solid bulk medium. The self-compression behavior was detailedly investigated under a variety of experimental conditions, and the temporal and spectral characteristics of resulted pulses were found to be significantly affected by the input pulse intensity, with higher intensity corresponding to shorter compressed pulses. By passing through a piece of BK7 glass, a self-compression from 50 to 20 fs was achieved, with a compression factor of about 2.5. However, the output pulse was observed to be split into two peaks when the input intensity is high enough to generate supercontinuum and conical emission. (c) 2005 Elsevier B.V. All rights reserved.

Compression of intense laser pulse through filamentation in an argon-filled cell

We demonstrate a pulse compression technique through filamentation in an argon-filled cell. By using a pair of chirped mirrors for dispersion compensation, we have successfully compressed the 53 fs pulse to 15 fs with good spatial qualities and good pulse stability. The total transmitted efficiency is more than 75%. The influence of the experiment parameters to the compressed pulses is also studied experimentally.

再生放大器宽带光谱整形的双折射片设计

提出了一种用于再生放大器中展宽光谱的双折射片的设计方法，利用这种方法设计了厚度为761微米的石英双折射片，并将其插入钛宝石再生放大器中，有效抑制了增益窄化效应，实验的结果和理论计算一致。使用设计的石英双折射片后光谱带宽由使用前的28nm展宽到了62nm，最后压缩脉冲为23fs。

Parasitic lasing suppression in high gain femtosecond petawatt Ti: sapphire amplifier

New parasitic lasing suppression techniques are developed and high gain amplification is demonstrated in a petawatt level Ti:sapphire amplifier based on the chirped pulse amplification (CPA) scheme. Cladding the large aperture Ti: sapphire with refractive-index matched liquid doped with absorber suppresses the transverse lasing. The acousto-optic programmable dispersive filter (AOPDF) is used to realize side-lobe suppression in the temporal profile of the compressed pulse. The 800 nm laser output with peak power of 0.89 PW and pulse width of 29.0 fs is demonstrated. (c) 2007 Optical Society of America.