Combustion products of bulk aluminum rods burning in high pressure oxygen

Characterization of the combustion products released during the burning of commonly used engineering metallic materials may aid in material selection and risk assessment for the design of oxygen systems. The characterization of combustion products in regards to size distribution and morphology gives useful information for systems addressing fire detection. Aluminum rods (3.2-mm diameter cylinders) were vertically mounted inside a combustion chamber and ignited in pressurized oxygen by resistively heating an aluminum/palladium igniter wire attached to the bottom of the test sample. This paper describes the experimental work conducted to establish the particle size distribution and morphology of the resultant combustion products collected after the burning was completed and subsequently analyzed. In general, the combustion products consisted of a re-solidified oxidized slag and many small hollow spheres of size ranging from about 500 nm to 1000 µm in diameter, surfaced with quenched dendritic and grain-like structures. The combustion products were characterized using optical and scanning electron microscopy.

The influence of atmospheric conditions on the leakage current of ceramic insulators on the Colombian Caribbean coast

The contamination of electrical insulators is one of the major contributors to the risk of operation outages in electrical substations, especially in coastal zones with high salinity levels and atmospheric pollution. By using the measurement of leakage-currents, which is one of the main indicators of contamination in insulators, this work seeks to the determine the correlation with climatic variables, such as ambient temperature, relative humidity, solar irradiance, atmospheric pressure, and wind speed and direction. The results obtained provide an input to the behaviour of the leakage current under atmospheric conditions that are particular to the Caribbean coast of Colombia. Spearman’s rank correlation coefficients and principal component analysis are utilised to determine the significant relationships among the different variables under consideration. The necessary information for the study was obtained via historical databases of both atmospheric variables and the leakage current measured in over a period of one year in a 220-kV potential transformer insulator. We identified the influencing factors of temperature, humidity, radiation, wind speed and direction on the magnitude of the leakage current as the most relevant.

Analysis of arm elevation muscle activity through different movement planes and speeds during in-water and dry-land exercise

Objective The objectives of this cross-sectional, analytical inference analysis were to compare shoulder muscle activation at arm elevations of 0° to 90° through different movement planes and speeds during in-water and dry-land exercise and to extrapolate this information to a clinical rehabilitation model. Methods Six muscles of right-handed adult subjects (n = 16; males/females: 50%; age: 26.1 ± 4.5 years) were examined with surface electromyography during arm elevation in water and on dry land. Participants randomly performed 3 elevation movements (flexion, abduction, and scaption) through 0° to 90°. Three movement speeds were used for each movement as determined by a metronome (30°/sec, 45°/sec, and 90°/sec). Dry-land maximal voluntary contraction tests were used to determine movement normalization. Results Muscle activity levels were significantly lower in water compared with dry land at 30°/sec and 45°/sec but significantly higher at 90°/sec. This sequential progressive activation with increased movement speed was proportionally higher on transition from gravity-based on-land activity to water-based isokinetic resistance. The pectoralis major and latissimus dorsi muscles showed higher activity during abduction and scaption. Conclusions These findings on muscle activation suggest protocols in which active flexion is introduced first at low speeds (30°/sec) in water, then at medium speeds (45°/sec) in water or on dry land, and finally at high speeds (90°/sec) on dry land before in water. Abduction requires higher stabilization, necessitating its introduction after flexion, with scaption introduced last. This model of progressive sequential movement ensures that early active motion and then stabilization are appropriately introduced. This should reduce rehabilitation time and improve therapeutic goals without compromising patient safety or introducing inappropriate muscle recruitment or movement speed.

A comparison land-water environment of maximal voluntary isometric contraction during manual muscle testing through surface electromyography

Background The aim of this study was to compare through surface electromyographic (sEMG) recordings of the maximum voluntary contraction (MVC) on dry land and in water by manual muscle test (MMT). Method Sixteen healthy right-handed subjects (8 males and 8 females) participated in measurement of muscle activation of the right shoulder. The selected muscles were the cervical erector spinae, trapezius, pectoralis, anterior deltoid, middle deltoid, infraspinatus and latissimus dorsi. The MVC test conditions were random with respect to the order on the land/in water. Results For each muscle, the MVC test was performed and measured through sEMG to determine differences in muscle activation in both conditions. For all muscles except the latissimus dorsi, no significant differences were observed between land and water MVC scores (p = 0.063–0.679) and precision (%Diff = 7–10%) were observed between MVC conditions in the muscles trapezius, anterior deltoid and middle deltoid. Conclusions If the procedure for data collection is optimal, under MMT conditions it appears that comparable MVC sEMG values were achieved on land and in water and the integrity of the EMG recordings were maintained during wáter immersion.

Assessment of the risk of failure of high voltage substations due to environmental conditions and pollution on insulators

Pollution on electrical insulators is one of the greatest causes of failure of substations subjected to high levels of salinity and environmental pollution. Considering leakage current as the main indicator of pollution on insulators, this paper focus on establishing the effect of the environmental conditions on the risk of failure due to pollution on insulators and determining the significant change in the magnitude of the pollution on the insulators during dry and humid periods. Hierarchical segmentation analysis was used to establish the effect of environmental conditions on the risk of failure due to pollution on insulators. The Kruskal-Wallis test was utilized to determine the significant changes in the magnitude of the pollution due to climate periods. An important result was the discovery that leakage current was more common on insulators during dry periods than humid ones. There was also a higher risk of failure due to pollution during dry periods. During the humid period, various temperatures and wind directions produced a small change in the risk of failure. As a technical result, operators of electrical substations can now identify the cause of an increase in risk of failure due to pollution in the area. The research provides a contribution towards the behaviour of the leakage current under conditions similar to those of the Colombian Caribbean coast and how they affect the risk of failure of the substation due to pollution.

Immunochip analysis identifies multiple susceptibility loci for systemic sclerosis

In this study, 1,833 systemic sclerosis (SSc) cases and 3,466 controls were genotyped with the Immunochip array. Classical alleles, amino acid residues, and SNPs across the human leukocyte antigen (HLA) region were imputed and tested. These analyses resulted in a model composed of six polymorphic amino acid positions and seven SNPs that explained the observed significant associations in the region. In addition, a replication step comprising 4,017 SSc cases and 5,935 controls was carried out for several selected non-HLA variants, reaching a total of 5,850 cases and 9,401 controls of European ancestry. Following this strategy, we identified and validated three SSc risk loci, including DNASE1L3 at 3p14, the SCHIP1-IL12A locus at 3q25, and ATG5 at 6q21, as well as a suggested association of the TREH-DDX6 locus at 11q23. The associations of several previously reported SSc risk loci were validated and further refined, and the observed peak of association in PXK was related to DNASE1L3. Our study has increased the number of known genetic associations with SSc, provided further insight into the pleiotropic effects of shared autoimmune risk factors, and highlighted the power of dense mapping for detecting previously overlooked susceptibility loci.

Ink-jet printing of graphene for flexible electronics: An environmentally-friendly approach

Mechanical flexibility is considered an asset in consumer electronics and next-generation electronic systems. Printed and flexible electronic devices could be embedded into clothing or other surfaces at home or office or in many products such as low-cost sensors integrated in transparent and flexible surfaces. In this context inks based on graphene and related two-dimensional materials (2DMs) are gaining increasing attention owing to their exceptional (opto)electronic, electrochemical and mechanical properties. The current limitation relies on the use of solvents, providing stable dispersions of graphene and 2DMs and fitting the proper fluidic requirements for printing, which are in general not environmentally benign, and with high boiling point. Non-toxic and low boiling point solvents do not possess the required rheological properties (i.e., surface tension, viscosity and density) for the solution processing of graphene and 2DMs. Such solvents (e.g., water, alcohols) require the addition of stabilizing agents such as polymers or surfactants for the dispersion of graphene and 2DMs, which however unavoidably corrupt their properties, thus preventing their use for the target application. Here, we demonstrate a viable strategy to tune the fluidic properties of water/ethanol mixtures (low-boiling point solvents) to first effectively exfoliate graphite and then disperse graphene flakes to formulate graphene-based inks. We demonstrate that such inks can be used to print conductive stripes (sheet resistance of ~13 kΩ/□) on flexible substrates (polyethylene terephthalate), moving a step forward towards the realization of graphene-based printed electronic devices.

Perinatal nutrition and gastrointestinal disorders : Working Group Report of the Second World Congress of Pediatric Gastroenterology, Hepatology, and Nutrition

Metabolic programming during the perinatal period as a consequence of early nutrition is an emerging area of great interest. This concept is known as the "fetal origins of adult disease" theory (1). Numerous epidemiological studies published over the past 20 years or so have suggested that small body size at birth and during infancy and, more specifically, intrauterine growth retardation are associated later in life with lowered cognitive performance and increased rates of coronary heart disease and its major biological risk factors, ie, raised blood pressure, insulin resistance, coronary artery disease, and abnormalities in lipid metabolism. The molecular mechanisms that govern this phenomenon in humans, however, are unknown and need to be elucidated.

Spray deposition of exfoliated MoS2 flakes as hole transport layer in perovskite-based photovoltaics

We propose the use of solution-processed molybdenum disulfide (MoS2) flakes as hole transport layer (HTL) for metal-organic perovskite solar cells. MoS2 bulk crystals are exfoliated in 2-propanol and deposited on perovskite layers by spray coating. We fabricated cells with glass/FTO/compact-TiO2/mesoporous-TiO2/CH3NH3PbI3/spiro- OMeTAD/Au structure and cells with the same structure but with MoS2 flakes as HTL instead of spiro-OMeTAD, the most widely used HTL. The electrical characterization of the cells with MoS2 as HTL show promising power conversion efficiency -η- of 3.9% with respect to cells with pristine spiro-OMeTAD (η=3.1%). Endurance test on 800-hour shelf life has shown higher stability for the MoS2–based cells (ΔPCE/PCE=-17%) with respect to the doped spiro-OMeTAD-based one (ΔPCE/PCE =-45%). Further improvements are expected with the optimization of the MoS2 deposition process

Expected Performance of the ATLAS Experiment - Detector, Trigger and Physics

A detailed study is presented of the expected performance of the ATLAS detector. The reconstruction of tracks, leptons, photons, missing energy and jets is investigated, together with the performance of b-tagging and the trigger. The physics potential for a variety of interesting physics processes, within the Standard Model and beyond, is examined. The study comprises a series of notes based on simulations of the detector and physics processes, with particular emphasis given to the data expected from the first years of operation of the LHC at CERN.

An estimate of the number of tropical tree species

The high species richness of tropical forests has long been recognized, yet there remains substantial uncertainty regarding the actual number of tropical tree species. Using a pantropical tree inventory database from closed canopy forests, consisting of 657,630 trees belonging to 11,371 species, we use a fitted value of Fisher's alpha and an approximate pantropical stem total to estimate the minimum number of tropical forest tree species to fall between similar to 40,000 and similar to 53,000, i.e., at the high end of previous estimates. Contrary to common assumption, the Indo-Pacific region was found to be as species-rich as the Neotropics, with both regions having a minimum of similar to 19,000-25,000 tree species. Continental Africa is relatively depauperate with a minimum of similar to 4,500-6,000 tree species. Very few species are shared among the African, American, and the Indo-Pacific regions. We provide a methodological framework for estimating species richness in trees that may help refine species richness estimates of tree-dependent taxa.

Análisis de la contribución de los sistemas silvopastoriles a la conservación de la flora y fauna en tres comunidades de la reserva de biósfera Bosawás

El estudio se realizó en tres comunidades del Territorio Miskitu Indian Tasbaika Kum, Reserva de Biósfera BOSAWAS (Shiminka, Boca de Plis y Esperanza), para describir la interacción entre especies de flora y avifauna y su influencia en la conservación de estas especies en las áreas de pastoreo, a partir de tres criterios: 1) cuantificar flora y avifauna, 2) prácticas de manejo tradicional, 3) estimar beneficios económico generado por sistemas de pastoreo. Se establecieron tres puntos de conteo dentro de transeptos para avifauna, se estableció parcelas para muestreo de la vegetación en cada comunidad, se seleccionó una comunidad beneficiada por subproyectos del Proyecto Corazón (MARENA) y dos áreas clasificadas como bosque secundario. Para evaluar el beneficio económi co se aplicó entrevistas abiertas y estructuradas dirigida a propietarios de ganado, para documentar los principales beneficios tangibles e intangibles que la población obtiene de estos agrosistemas. El análisis de resultados se determinó en base a índices de diversidad, dominancia, equidad y similitud; tomando en cuenta la riqueza, abundancia y densidad de especies. Se encontró que para flora Shiminka obtuvo los mayores valores de dominancia lo que indica que se encuentran especies de mayor importancia, Esperanza tiene mayor equidad y diversidad, en Shiminka y Esperanza se necesitan mayores estudios, el análisis de Clúster arrojó que aunque existe alguna concordancia entre Boca de Plis y Shiminka, las tres difieren entre sí y el mismo resultado se encontró para la avifauna; y para fauna mayor equidad en Shiminka y Esperanza, mientras la más diversa resultó Esperanza. La similitud establece que Boca de Plis y Esperanza necesitan mayor intensidad de muestreo.

Evaluación del establecimiento de tres especies forestales en la unidad experimental finca El Plantel, Nindirí, Masaya

El estudio se realizó en la Finca El Plantel, propiedad de la Universidad Nacional Agraria, para evaluar el establecimiento de Hymenaea courbaril, Tabebuia ochracea y Caesalpinia violacea con el propósito de conocer su comportamiento en sobrevivencia, diámetro y altura. La plantación se estableció en parcelas con dimensiones de 15 x 15m , teniendo un distanciamiento de 3 x 3m entre cada planta. Considerando el efecto de borde la cantidad de plantas evaluadas por especie es de cuarenta y ocho, para un total de 144 individuos. Efectuándose dos mediciones con respecto a variable sobrevivencia, diámetro y altura; donde la primera se realizó en octubre 2009 y la segunda en octubre de 2010. Al final del periodo de la evaluación se realizó un monitoreo de los daños observados en la plantación (octubre del 2010). La plantación obtuvo una sobrevivencia global de 63%, siendo C. violacea la especie que obtuvo mayor porcentaje 69%, H. courbaril con 63% y Tabebuia ochracea (57.6%) la que obtuvo el menor porcentaje. Caesalpinia violacea obtuvo un notorio incremento en altura con 123.3 cm superando a T. ochracea (37 cm) y H. courbaril (15.1 cm). En cuanto al incremento en diámetro Hymenaea courbaril (4.43 mm) obtuvo casi el doble del incremento que las otras dos especies, C. violacea (2.29 mm) y T.ochracea (1.79 mm). Haciendo una valoración general de los principales daños registrados en la plantación corresponden a la categoría defoliación 64.9%. Las especies T. ochracea y C. violacea reportaron mayor del 80% de las plantas afectadas por defoliación, causada por zompopos del género Attacephalotus, sin embargo; Hymenaea courbaril se encontraba sin ningún tipo de daños.