Temperature variation at the external root surface during 980-nm diode laser irradiation in the root canal

Objective: To assess the temperature variation in the cervical, middle and apical thirds of root external wall, caused by 980-nm diode laser irradiation with different parameters. Methods: The roots of 90 canines, had their canals instrumented and were randomly distributed into 3 groups (n = 30) according to the laser potency (1.5 W, 3.0 W and 5.0 W). Each group was subdivided into 3 (n = 10) according to the frequency (CM, 100 Hz and 1000 Hz), and each subgroup divided into 2 (n = S): dried canal or filled with distilled water. The maximum temperature values were collected by 3 thermocouples located at each third of the root external wall and recorded by digital thermometers. Results: The groups irradiated in the continuous mode (CM) presented the highest values (11.82 +/- 5.78), regardless of the canals were dry or not, which were statistically different (p < 0.01) from those obtained with 100 Hz (6.22 +/- 3.64) and 1000 Hz (6.00 +/- 3.36), which presented no statistical difference between them (p > 0.01). The groups irradiated with 5.0 W presented the greatest temperature variation (12.15 +/- 5.14), followed by 3.0 W (7.88 +/- 3.92) and 1.5 W (4.02 +/- 2.16), differing between them (p < 0.01). The cervical third of the root presented the highest temperature rises (9.68 +/- 5.80), followed by the middle (7.66 +/- 4.87) and apical (6.70 +/- 4.23), with statistical difference among them (p < 0.01). After 30 s from the end of irradiation, all the specimens presented temperature variation lower than 10 degrees C. Conclusions: Application of 980-nm diode laser in the root, at 1.5 W in all operating modes, and 3.0 W, in the pulsed mode, for 20 s, can safely be used in endodontic treatment, irrespective of the presence of humidity. (C) 2008 Elsevier Ltd. All rights reserved.

Influence of Filling Materials on the Bonding Interface of Thin-walled Roots Reinforced with Resin and Quartz Fiber Posts

Introduction: A common complication during the restoration of severely destroyed teeth is the loss of coronal root dentine. The aim of this study was to evaluate the influence of different sealers on the bonding interface of weakened roots reinforced with resin and fiber posts. Methods: Sixty extracted maxillary canines were used. The crowns were removed, and the thickness of root dentine was reduced in the experimental (n = 40) and positive control (n = 10) groups. The specimens of experimental group were assigned to four subgroups (n = 10) according to the filling material: gutta-percha + Grossmann`s sealer, gutta-percha + AH Plus (Dentsply De Trey Gmbh, Konstanz, Germany), gutta-percha + Epiphany (Pentron Clinical Technologies, Wallingford, CT), and Resilon (Resilon Research LLC, Madison, CT) + Epiphany. In the negative control group (n = 10), canals were not filled. After post space preparation, the roots were restored with composite resin light-activated through a translucent fiber post. After 24 hours, specimens were transversally sectioned into 1-mm-thick slices. Push-out test and scanning electron microscopic (SEM) analyses of different regions were performed. Data from push-out test were analyzed by using Tukey post hoc multiple comparison tests. The percentage of failure type was calculated. Data from SEM analysis were compared by Friedman and Kruskal-Wallis tests (alpha = 0.05). Results: The mean bond strength was significantly higher in the negative control group as compared with the other groups (P < .05). In all groups, the most frequent type of failure was adhesive. Overall, apical and middle regions presented a lower density of resin tags than the coronal region (P < .05). Conclusions: The push-out bond strength was not affected by sealer or region. The canal region affected significantly the resin tag morphology and density at the bonding interface. (J Endod 2011;37:531-537)

Influence of shaft design on the shaping ability of 3 nickel-titanium rotary systems by means of spiral computerized tomography

Objective. To evaluate the influence of shaft design on the shaping ability of 3 rotary nickel-titanium (NiTi) systems. Study design. Sixty curved mesial canals of mandibular molars were used. Specimens were scanned by spiral tomography before and after canal preparation using ProTaper, ProFile, and ProSystem GT rotary instruments. One-millimeter-thick slices were scanned from the apical end point to the pulp chamber. The cross-sectional images from the slices taken earlier and after canal preparation at the apical, coronal, and midroot levels were compared. Results. The mean working time was 137.22 +/- 5.15 s. Mean transportation, mean centering ratio, and percentage of area increase were 0.022 +/- 0.131 mm, 0.21 +/- 0.11, and 76.90 +/- 42.27%, respectively, with no statistical differences (P > .05). Conclusions. All instruments were able to shape curved mesial canals in mandibular molars to size 30 without significant errors. The differences in shaft designs seemed not to affect their shaping capabilities.

Influence of different endodontic filling materials on root fracture susceptibility

Objective: To evaluate the influence of different endodontic materials on root fracture susceptibility. Methods: Seventy-two mandibular incisors were sectioned 1 mm below the cementoenamel junction to obtain roots of 12 mm length. Roots were submitted to chemomechanical preparation with the rotary instruments of Profile system. The obturation of root canals were performed with the following filling materials (n = 12): GI, unfilled teeth (control); GII, Endofill + gutta-percha; GIII, Sealer 26 + gutta-percha; GIV, AH Plus + gutta-percha; GV, Epiphany + gutta-percha; GVI, Epiphany + Resilon. After the sealers setting time, each root was embedded in acrylic resin. The specimens were then submitted to fracture resistance test using an Instron testing machine at 1 mm/min. Results: The ANOVA test showed no significant statistical difference (p > .05) among GI (162.16 +/- 41.4N), GII (168.46 +/- 37.5N), GIII (164.83 +/- 35.7N), GIV (168.29 +/- 38.7N), GV (172.36 +/- 20.6N) and GVI (193.11 +/- 42.8N). Conclusion: The core materials (gutta-percha or Resilon) combined with the tested endodontic sealers are not able to increase the root fracture resistance in canals submitted to chemomechanical preparation. (c) 2007 Elsevier Ltd. All rights reserved.

Effect of Chelating Solutions on the Microhardness of Root Canal Lumen Dentin

Introduction: The greatest reduction in microhardness of the most superficial layer of dentin of the root canal lumen is desired. The use of chelating agents during biomechanical preparation of root canals removes smear layer, increasing the access of the irrigant into the dentin tubules to allow adequate disinfection, and also reduces dentin microhardness, facilitating the action of endodontic instruments. This study evaluated the effect of different chelating solutions on the microhardness of the most superficial dentin layer from the root canal lumen. Methods: Thirty-five recently extracted single-rooted maxillary central incisors were instrumented, and the roots were longitudinally sectioned in a mesiodistal direction to expose the entire canal extension. The specimens were distributed in seven groups according to the final irrigation: 15% EDTA, 10% citric acid, 5% malic acid, 5% acetic acid, apple vinegar, 10% sodium citrate, and control (no irrigation). A standardized volume of 50 mu L of each chelating solution was used for 5 minutes. Dentin microhardness was measured with a Knoop indenter under a 10-g load and a 15-second dwell time. Data were analyzed statistically by one-way analysis of variance and Tukey-Kramer multiple-comparison test at 5% significance level. Results: EDTA and citric acid had the greatest overall effect, causing a sharp decrease in dentin microhardness without a significant difference (p > .05) from each other. However, both chelators differed significantly from the other solutions (p < .001). Sodium citrate and deionized water were similar to each other (p > .05) and did not affect dentin microhardness. Apple vinegar, acetic acid, and malic acid were similar to each other (p > .05) and presented intermediate results. Conclusion: Except for sodium citrate, all tested chelating solutions reduced microhardness of the most superficial root canal dentin layer. EDTA and citric acid were the most efficient. (J Endod 2011;37:358-362)

The lateral line canal sensory organs of the Epaulette Shark (Hemiscyllium ocellatum)

Examination of the lateral line canals in the Epaulette Shark reveals a much more differentiated sensory system than previously reported from any elasmobranch. Two main types of lateral line canals are found. In one type rounded patches of sensory epithelia are separated by elevations of the canal floor. The other type is a straight canal without restrictions and with an almost continuous sensory epithelium. In addition, we found epithelia (type A) with very long apical microvilli on the supporting cells. These microvilli reach beyond the stereovilli of the hair cells. Another type (B) of sensory epithelium has short microvilli on the supporting cells. In this latter type of epithelium the stereovilli of the hair cells are comparatively tall and reach out beyond the supporting cell microvilli. New hair cells are found widely in both types of sensory epithelia. These always occur as single cells, unlike those described in teleost lateral line canal sensory epithelia where new hair cells seem to form in pairs. Dying hair cells are also widespread, indicating a continuous turnover of hair cells.

The current status of laser applications in dentistry

A range of lasers. is now available for use in dentistry. This paper summarizes key current and emerging applications, for lasers in clinical practice. A major diagnostic application of low power lasers is the detection of caries, using fluorescence elicited from hydroxyapatite or from bacterial by-products. Laser fluorescence is an effective method for detecting and quantifying incipient occlusal and cervical,carious lesions, and with further refinement could be used in the, same manner for proximal lesions. Photoactivated dye techniques have been developed which use low power lasers to elicit a photochemical reaction, Photoactivated dye techniques' can be used to disinfect root canals, periodontal pockets, cavity preparations and sites of peri-implantitis. Using similar principles, more powerful lasers tan be used for photodynamic therapy in the treatment of malignancies of the oral mucosa. Laser-driven photochemical reactions can also be used for tooth whitening. In combination with fluoride, laser irradiation can improve the resistance of tooth structure to demineralization, and this application is of particular benefit for susceptible sites in high caries risk patients. Laser technology for caries' removal, cavity preparation and soft tissue surgery is at a high state of refinement, having had several decades of development up to the present time. Used in conjunction with or as a replacement for traditional methods, it is expected that specific laser technologies will become an essential component of contemporary dental practice over the next decade.

Occurrence of immature Culicoides molestus (Skuse) (Diptera : Ceratopogonidae) in relation to habitat characteristics

Analysis of beach sites on the Gold Coast, Australia, found that 14 physical and chemical habitat characteristics differed significantly between sites where numerous immatures of the canal biting midge, Culicoides molestus (Skuse), were found and sites where no midge immatures occurred. Five of the chemical factors found to reliably distinguish C. molestus habitat are major components of seawater, while another, electrical conductivity, is related to the concentration of seawater components. Calcium was the only one of the six primary components of seawater that was not a statistically significant correlate of C. molestus habitation by sand analysis. It is likely that a causative variable in occurrence of immatures is the concentration of seawater present in canals, because larvae are found where seawater component concentration is low in relation to uninhabited sites of similar appearance.

Metodologia para obtenção do hidrograma de escoamento superficial em encostas e canais. Parte I: desenvolvimento e avaliação

Desenvolveu-se uma metodologia que permite obter o hidrograma de escoamento superficial e a vazão máxima para qualquer posição ao longo de uma encosta e para seções transversais de canais utilizando o modelo de ondas cinemáticas. A área da encosta é dividida num sistema matricial composto por 100 linhas e 100 colunas. Na encosta, considera-se que o escoamento ocorre na direção da declividade e que a vazão de cada pixel é a soma da vazão produzida nesse com a vazão advinda dos pixels que contribuem com o escoamento superficial para o pixel em análise. No canal, a vazão é calculada pela soma dos hidrogramas advindos das colunas do sistema reticulado. A comparação entre os valores de lâmina e vazão máxima de escoamento superficial obtidas experimentalmente e calculadas em duas condições (encosta e bacia) permitiu evidenciar que a metodologia, comparada aos métodos Racional e do Número da Curva, ofereceu boas estimativas tanto da lâmina quanto da vazão máxima de escoamento superficial.

Metodologia para obtenção do hidrograma de escoamento superficial em encostas e canais. Parte II: modelo computacional e análise de sensibilidade

Estimativas de vazão máxima de escoamento superficial são necessárias para o projeto de obras hidráulicas em bacias urbanas e rurais. A dificuldade em aplicar os procedimentos disponíveis para calcular a variação do escoamento superficial com o tempo e de seu valor máximo deve-se à inexatidão dos métodos usados para esse objetivo e à variabilidade nos resultados que podem ser obtidos por profissionais que usem o mesmo procedimento. Dessa forma, a investigação de um método que produza estimativas confiáveis da vazão máxima e do hidrograma de escoamento superficial é de grande interesse. Neste trabalho, desenvolveu-se e avaliou-se a sensibilidade de um software (HIDROGRAMA 2.1) que permite a obtenção do hidrograma de escoamento superficial, da vazão máxima e seu tempo de ocorrência, da altura e da velocidade máximas do escoamento, do volume e da lâmina de escoamento superficial em encosta e em canais. O modelo apresentou grande sensibilidade ao período de retorno, à taxa de infiltração estável e ao comprimento da encosta e do canal.

Modeling for control design of a multi-reach water canal

This article addresses the problem of obtaining reduced complexity models of multi-reach water delivery canals that are suitable for robust and linear parameter varying (LPV) control design. In the first stage, by applying a method known from the literature, a finite dimensional rational transfer function of a priori defined order is obtained for each canal reach by linearizing the Saint-Venant equations. Then, by using block diagrams algebra, these different models are combined with linearized gate models in order to obtain the overall canal model. In what concerns the control design objectives, this approach has the advantages of providing a model with prescribed order and to quantify the high frequency uncertainty due to model approximation. A case study with a 3-reach canal is presented, and the resulting model is compared with experimental data. © 2014 IEEE.

Modeling for control design of a multi-reach water canal

This article addresses the problem of obtaining reduced complexity models of multi-reach water delivery canals that are suitable for robust and linear parameter varying (LPV) control design. In the first stage, by applying a method known from the literature, a finite dimensional rational transfer function of a priori defined order is obtained for each canal reach by linearizing the Saint-Venant equations. Then, by using block diagrams algebra, these different models are combined with linearized gate models in order to obtain the overall canal model. In what concerns the control design objectives, this approach has the advantages of providing a model with prescribed order and to quantify the high frequency uncertainty due to model approximation. A case study with a 3-reach canal is presented, and the resulting model is compared with experimental data. © 2014 IEEE.

DISTRIBUTION AND FEEDING ECOLOGY OF THE AFRICAN TILAPIA Oreochromis mossambicus (TELEOSTEI, PERCIFORMES, CICHLIDAE) IN SURINAME (SOUTH AMERICA) WITH COMMENTS ON THE TILAPIA-KWIKWI (Hoplosternum littorale) (TELEOSTEI, SILURIFORMEs, CALLICHTHYIDAE) INTERACTION

The geographical distribution of the African Tilapia Oreochromis mossambicusin Suriname is restricted to a narrow strip of land along the Atlantic coast. Within the coastal plain, O. mossambicusoccurs in brackish lagoons, oligohaline canals, and shell-sand pit lakes. Physico-chemical characteristics and phytoplankton composition of representative Tilapia water bodies are described. Blue-green algae and fine flocculent detritus are dominant food items in the diet of the Tilapia, while Rotifera and microcrustacea are also important in the diet of larvae and juveniles. Intraspecific diet overlap among ontogenetic stages of the Tilapia did not differ significantly from 1, which means that these diets showed complete overlap. Interspecific diet overlap between the Tilapia and the indigenous armoured catfish Hoplosternum littoralewere moderate or low. The results are discussed in relation to recent developments in the Surinamese fisheries and aquaculture sector.

Distribució de revistes científiques en format digital

L'aparició de les revistes en format digital posa de nou de manifest la necessitat de disposar de bons mecanismes de distribució i accés a les mateixes. Això encara esdevé més rellevant en els actuals moments de concentració en grans grups empresarials de l'edició i la distribució de les revistes de l'anomenat àmbit científic, tècnic i mèdic (STM: “scientific, technical and medical”). Davant d'aquest fenomen, encara ho tenen més complicat les publicacions amb una circulació més restringida per raons de llengua o d'especialització. És el cas de moltes revistes publicades a Catalunya, editades i distribuïdes per canals diferents als del sistema STM comercial internacional. Davant d’aquesta problemàtica, el Consorci de Biblioteques Universitàries de Catalunya (CBUC) ha encarregat el present informe. Un dels objectius fonamentals del CBUC és facilitar l'accés dels usuaris a la informació especialitzada; dins d'aquesta es vol prestar un suport especial als continguts creats a Catalunya per tal de facilitar-ne la seva utilització i contribuir al seu desenvolupament futur. Dins l’actual moment de canvi provocat per la irrupció de l’edició digital, es corre el risc de que els continguts catalans no tinguin la suficient presència i utilització en aquest nou suport, cosa que suposaria un evident endarreriment. Per tal d’evitar-ho, el CBUC vol explorar les implicacions i les possibilitats de crear plataformes o portals per a la difusió de les revistes erudites catalanes, en el cas que no ho puguin fer pels canals comercials internacionals. A nivell operatiu aquest informe intenta respondre a les següents preguntes: Què és un portal de revistes científiques?, Quins elements s’han de preveure en la seva constitució?, Quines alternatives de servei hi ha?, Quines problemàtiques tècniques es plantegen? i Existeixen iniciatives o inquietuds semblants a les plantejades pel CBUC?

La Transició nutricional a la Catalunya contemporània 1780-1936

Un dels principals exponents del progrés en el nivell de vida és l’existència d’un accés generalitzat i regular de la població a una ingesta d’aliments suficient i de qualitat, que cobreixi de forma adequada els requeriments pel ple desenvolupament fisiològic i que suposi la reducció al mínim de les malalties associades a l’alimentació. Durant una gran part de la història, l’alimentació de les poblacions humanes, i en particular de les europees, s’ha caracteritzat per la seva monotonia i la irregularitat en la disponibilitat dels aliments més importants. Aquestes, juntament amb un deficient tractament higiènic i de conservació dels aliments ingerits, seran les notes dominants dels sistemes alimentaris europeus durant molts segles. Va ser des de finals del segle XVIII i principis del segle XIX quan, simultàniament al desenvolupament de la producció agrària i a la industrialització, es va iniciar el que es considera com una transició nutricional o dietètica moderna, que ha culminat a la segona meitat del segle XX amb profunds canvis en els sistemes alimentaris. Catalunya no estarà al marge d’aquestes transformacions, i experimentarà des del segle XVIII importants canvis en els seus sistemes agraris, els seus sistemes alimentaris, els canals de distribució i el modern tractament dels aliment. L’objectiu d’aquest treball és doncs, analitzar com es manifesta aquesta transició alimentària a la Catalunya contemporània, que es situa entre mitjans segle XIX i la guerra civil.