Heat shock resistance traits in specimens of the seaweed Gracilaria vermiculophylla originating from native and non-native populations

We compared the responses of native and non-native populations of the seaweed Gracilaria vermiculophylla to heat shock in common garden-type experiments. Specimens from six native populations in East Asia and from eight non-native populations in Europe and on the Mexican Pacific coast were acclimated to two sets of identical conditions before their resistance to heat shock was examined. The experiments were carried out twice - one time in the native range in Qingdao, China and one time in the invaded range in Kiel, Germany - to rule out effects of specific local conditions. In both testing sites the non-native populations survived heat shock significantly better than the native populations, The data underlying this statement are presented in https://doi.pangaea.de/10.1594/PANGAEA.859335. After three hours of heat shock G. vermiculophylla exhibited increased levels of heat shock protein 70 (HSP70) and of a specific isoform of haloperoxidase, suggesting that both enzymes could be required for heat shock stress management. However, the elevated resistance toward heat shock of non-native populations only correlated with an increased constitutive expression of heat shock protein 70 (HSP70). The haloperoxidase isoform was more prominent in native populations, suggesting that not only increased HSP70 expression, but also reduced allocation into haloperoxidase expression after heat shock was selected during the invasion history. The data describing expression of HSP70 and three different isoforms of haloperoxidase are presented in https://doi.pangaea.de/10.1594/PANGAEA.859358.

The Effect of Sequence of Operations on Fatigue Life of LSP Treated Open-hole Aluminium Specimens

Fastener holes in aeronautical structures are typical sources of fatigue cracks due to their induced local stress concentration. A very efficient solution to this problem is to establish compressive residual stresses around the fastener holes that retard the fatigue crack nucleation and its subsequent local propagation. Previous work done on the subject of the application of LSP treatment on thin, open-hole specimens [1] has proven that the LSP effect on fatigue life of treated specimens can be detrimental, if the process is not properly optimized. In fact, it was shown that the capability of the LSP to introduce compressive residual stresses around fastener holes in thin-walled structures representative of typical aircraft constructions was not superior to the performance of conventional techniques, such as cold-working.

Fatigue in laser shock peened open-hole thin aluminium specimens

An experimental study was performed in order to determine the influence of the sequence of operations on the effectiveness of Laser Shock Peening (LSP) treatment in increasing the fatigue performances of open-hole aluminium specimens. Residual stress measurements, fractographic analysis and FEM analysis were performed, indicating the presence of compressive residual stresses on the surface of the treated specimens and tensile residual stresses in the mid-section along the thickness of the specimens. Negative effects on fatigue lives were encountered on the specimens with the hole already present, while positive effect were observed in specimens in which the hole was drilled after LSP treatment. These results indicate that LSP can be a good solution for “in production” application, in which open holes are to be drilled after the LSP treatment. The application in which LSP is used “in service” on structures with pre-existing cut-outs, has proven to be impracticable in the investigated configuration.

Packaging and testing of fiber Bragg gratings for use as strain sensor for rock specimens

This paper reports a packaging and calibration procedure for surface mounting of fiber Bragg grating (FBG) sensors to measure strain in rocks. The packaging of FBG sensors is performed with glass fiber and polyester resin, and then subjected to tensile loads in order to obtain strength and deformability parameters, necessaries to assess the mechanical performance of the sensor packaging. For a specific package, an optimal curing condition has been found, showing good repeatability and adaptability for non-planar surfaces, such as occurs in rock engineering. The successfully packaged sensors and electrical strain gages were attached to standard rock specimens of gabbro. Longitudinal and transversal strains under compression loads were measured with both techniques, showing that response of FBG sensors is linear and reliable. An analytical model is used to characterize the influences of rock substrate and FBG packaging in strain transmission. As a result, we obtained a sensor packaging for non-planar and complex natural material under acceptable sensitivity suitable for very small strains as occurs in hard rocks.

The Cohesive Crack Model Applied To Notched PMMA Specimens Obeying a Non Linear Behaviour Under Torsion Loading

This article presents a new material model developed with the aim of analyzing failure of blunt notched components made of nonlinear brittle materials. The model, which combines the cohesive crack model with Hencky's theory of total deformations, is used to simulate an experimental benchmark carried out previously by the authors. Such combination is achieved through the embedded crack approach concept. In spite of the unavailability of precise material data, the numerical predictions obtained show good agreement with the experimental results.