Wave dynamic processes induced by a supersonic projectile discharging from a shock tube

A numerical study on wave dynamic processes occurring in muzzle blast flows, which are created by a supersonic projectile released from the open-end of a shock tube into ambient air, is described in this paper. The Euler equations, assuming axisymmetric flows, are solved by using a dispersion-controlled scheme implemented with moving boundary conditions. Three test cases are simulated for examining friction effects on the muzzle flow. From numerical simulations, the wave dynamic processes, including two blast waves, two jet flows, the bow shock wave and their interactions in the muzzle blasts, are demonstrated and discussed in detail. The study shows that the major wave dynamic processes developing in the muzzle flow remain similar when the friction varies, but some wave processes, such as shock-shock interactions, shock-jet interactions and the contact surface instability, get more intensive, which result in more complex muzzle blast flows.

Analytical Study of Idealized Two-Dimensional Cellular Detonations

In this study, the idealized two-dimensional detonation cells were decomposed into the primary units referred to as sub-cells. Based on the theory of oblique shock waves, an analytical formula was derived to describe the relation between the Mach number ratio through triple-shock collision and the geometric properties of the cell. By applying a modified blast wave theory, an analytical model was developed to predict the propagation of detonation waves along the cell. The calculated results show that detonation wave is, first, strengthened at the beginning of the cell after triple-shock collision, and then decays till reaching the cell end. The analytical results were compared with experimental data and previous numerical results; the agreement between them appears to be good, in general.

爆炸载荷下三峡三期纵向围堰响应的离散元分析

通过离散元方法的数值模拟，首先对清江高洲二期碾压混凝土围堰在爆炸载荷下的响应进行了分析，经与实验结果比较，得到了较合适的材料参数；然后根据这些材料参数并结合实验提供的部分数据，分析了三峡三期纵向围堰在爆炸载荷条件下的振动速度随离爆源距离衰减的变化规律，以及振动速度随时间的变化规律等。计算结果表明，三峡三期围堰爆破拆除时振动安全问题集中在纵向围堰拆除，研究爆破载荷作用下纵向围堰的振动响应是非常重要的。

爆炸容器内冲击波系演化及壳体响应的数值研究

对中心装药爆炸后冲击波的产生、传播和壳体动态响应全过程进行了数值研究。认为RDX瞬时爆炸，爆炸近场采用自相似解；冲击波传播和波系演化采用PPM(the Piecewise Parabolic Method)格式求解Euler方程；壳体响应采用有限元方法求解拉氏坐标系下由虚功原理得到的动力学方程。壳体内壁面边界条件分别采用强耦合和弱耦合方法处理。结果表明：（1）当装药量相同时，薄壁壳体振型比厚壁宙体复杂得多，振幅也大；（2）当装药量不同，壳体厚度相同时，爆炸场冲击波的演化过程不同；（3）对少量装药，产生的冲击波强度低，壳体变形小，是否考虑内边界运动，对计算结果的影响不大；（4）在本文条件下，爆炸容器封头顶点所受的载荷最大，是取易发生破坏的地方，侧壁与爆点所在横截面的交线，也易破坏。

Propagation of Explosion Wave in Hard-Soft-Hard Layered Media

The paper presents a reasonable analysis for dynamic response and failure process of a plane multi-layered media, which are subjected to a blast loading. This blast loading is induced by a cylindric explosive put on the center of top surface of the layered media. With the help of numerical simulation technique provided by LS-DYNA software, the whole process of explosion wave propagation and attenuation can be revealed. The feature of local failure around the blasting site is also discussed in some detail. Our focus will be on the explosion wave attenuation for the hard-soft-hard sandwich layers. As seen in the paper, the computational results are delivered in a feasible way by comparing with experimental data.

Improving coastal livelihoods through sustainable aquaculture practices - a report to the collaborative APEC Grouper Research and Development Network

Wild-harvest fisheries for live reef fish are largely over-exploited or unsustainable because of over-fishing and the widespread use of destructive fishing practices such as blast and cyanide fishing. Sustainable aquaculture – such as that of groupers – is one option for meeting the strong demand for reef fish, as well as potentially maintaining or improving the livelihoods of coastal communities. This report from a short study by the STREAM Initiative draws on secondary literature, media sources and four diverse case studies from at-risk reef fisheries, to frame a strategy for encouraging sustainable aquaculture as an alternative to destructive fishing practices. It was undertaken as a component of the APEC-funded project Collaborative Grouper Research and Development Network (FWG/01/2001) to better understand how recent technical advances in grouper culture and other complementary work – including that of the Asia-Pacific Marine Finfish Aquaculture Network (APMFAN) hosted by NACA – could better support the livelihoods of poor coastal communities. (PDF contains 49 pages)

A Computational Module Assembled from Different Protease Family Motifs Identifies PI PLC from Bacillus cereus as a Putative Prolyl Peptidase with a Serine Protease Scaffold

Proteolytic enzymes have evolved several mechanisms to cleave peptide bonds. These distinct types have been systematically categorized in the MEROPS database. While a BLAST search on these proteases identifies homologous proteins, sequence alignment methods often fail to identify relationships arising from convergent evolution, exon shuffling, and modular reuse of catalytic units. We have previously established a computational method to detect functions in proteins based on the spatial and electrostatic properties of the catalytic residues (CLASP). CLASP identified a promiscuous serine protease scaffold in alkaline phosphatases (AP) and a scaffold recognizing a beta-lactam (imipenem) in a cold-active Vibrio AP. Subsequently, we defined a methodology to quantify promiscuous activities in a wide range of proteins. Here, we assemble a module which encapsulates the multifarious motifs used by protease families listed in the MEROPS database. Since APs and proteases are an integral component of outer membrane vesicles (OMV), we sought to query other OMV proteins, like phospholipase C (PLC), using this search module. Our analysis indicated that phosphoinositide-specific PLC from Bacillus cereus is a serine protease. This was validated by protease assays, mass spectrometry and by inhibition of the native phospholipase activity of PI-PLC by the well-known serine protease inhibitor AEBSF (IC50 = 0.018 mM). Edman degradation analysis linked the specificity of the protease activity to a proline in the amino terminal, suggesting that the PI-PLC is a prolyl peptidase. Thus, we propose a computational method of extending protein families based on the spatial and electrostatic congruence of active site residues.

Potential Application of Adsorptive Media to Enhance Phosphorus Uptake in Stormwater Basins and Wetlands at Lake Tahoe : literature review. Report to the University of California Davis Tahoe Research Group

Phosphorus removal by wetlands and basins in Lake Tahoe may be improved through designing these systems to filter storm water through media having higher phosphorus removal capabilities than local parent material. Substrates rich in iron, aluminum and calcium oftentimes have enhanced phosphorus removal. These substrates can be naturally occurring, byproducts of industrial or water treatment processes, or engineered. Phosphorus removal fundamentally occurs through chemical adsorption and/or precipitation and much of the phosphorus can be irreversibly bound. In addition to these standard media, other engineered substrates are available to enhance P removal. One such substrate is locally available in Reno and uses lanthanum coated diatomaceous earth for arsenate removal. This material, which has a high positive surface charge, can also irreversibly remove phosphorus. Physical factors also affect P removal. Specifically, specific surface area and particle shape affect filtration capacity, contact area between water and the surface area, and likelihood of clogging and blinding. A number of substrates have been shown to effectively remove P in case studies. Based upon these studies, promising substrates include WTRs, blast furnace slag, steel furnace slag, OPC, calcite, marble Utelite and other LWAs, zeolite and shale. However, other nonperformance factors such as environmental considerations, application logistics, costs, and potential for cementification narrow the list of possible media for application at Tahoe. Industrial byproducts such as slags risk possible leaching of heavy metals and this potential cannot be easily predicted. Fly ash and other fine particle substrates would be more difficult to apply because they would need to be blended, making them less desirable and more costly to apply than larger diameter media. High transportation costs rule out non-local products. Finally, amorphous calcium products will eventually cementify reducing their effectiveness in filtration systems. Based upon these considerations, bauxite, LWAs and expanded shales/clays, iron-rich sands, activated alumina, marble and dolomite, and natural and lanthanum activated diatomaceous earth are the products most likely to be tested for application at Tahoe. These materials are typically iron, calcium or aluminum based; many have a high specific surface area; and all have low transportation costs. (PDF contains 21 pages)

Cell fate specification during Caenorhabditis elegans male tail development

The cells of the specialized mating structures of the nematode Caenorhabditis elegans adult male tail develop from sex-specific divisions of postembryonic blast cells. One male-specific blast cell, B, is the precursor to all the cells of the copulatory spicules. Both cell interactions and autonomous fate specification mechanisms are utilized in the B lineage to specify fate.

During development the anterior daughter of B, B.a, generates four distinct pairs of cells. Cell ablation experiments indicate that the cells of each pair respond to positional cues provided by other male-specific blast cells. F and U promote anterior fates, Y.p promotes some posterior fates, and the B.a progeny promote posterior fates. The cells within each pair may also interact.

The lin-3/let-23 signalling pathway, identified for its function in C. elegans hermaphrodite vulval induction, mediates the signal from F and U. Reduction-of-function mutations in lin-3 (EGF-like signal), let-23 (receptor), sem-5 (adaptor), let-60 (ras), or lin-45 (raf) disrupt the fates of the anterior cells, and mimic F and U ablation. In addition, ectopically expressed lin-3 disrupts the fates of the posterior cells, and can promote anterior fates even in the absence of F and U.

A genetic screen of over 9000 mutagenized gametes recovered 22 mutations in 20 loci that disrupt fate specification in male tail lineages. Seven of these mutations may represent new genes that play a role in male tail development.

The first division of the B cell is asymmetric. The gene vab-3 is required for specification of B.a fates, and it may represent a factor whose activity is localized to the B.a cell via the gene lin-17. lin-17 acts both at the first division of the B cell and at specific other cell divisions in the lineage.

Investigation of hypervelocity impact phenomena using real-time concurrent diagnostics

Hypervelocity impact of meteoroids and orbital debris poses a serious and growing threat to spacecraft. To study hypervelocity impact phenomena, a comprehensive ensemble of real-time concurrently operated diagnostics has been developed and implemented in the Small Particle Hypervelocity Impact Range (SPHIR) facility. This suite of simultaneously operated instrumentation provides multiple complementary measurements that facilitate the characterization of many impact phenomena in a single experiment. The investigation of hypervelocity impact phenomena described in this work focuses on normal impacts of 1.8 mm nylon 6/6 cylinder projectiles and variable thickness aluminum targets. The SPHIR facility two-stage light-gas gun is capable of routinely launching 5.5 mg nylon impactors to speeds of 5 to 7 km/s. Refinement of legacy SPHIR operation procedures and the investigation of first-stage pressure have improved the velocity performance of the facility, resulting in an increase in average impact velocity of at least 0.57 km/s. Results for the perforation area indicate the considered range of target thicknesses represent multiple regimes describing the non-monotonic scaling of target perforation with decreasing target thickness. The laser side-lighting (LSL) system has been developed to provide ultra-high-speed shadowgraph images of the impact event. This novel optical technique is demonstrated to characterize the propagation velocity and two-dimensional optical density of impact-generated debris clouds. Additionally, a debris capture system is located behind the target during every experiment to provide complementary information regarding the trajectory distribution and penetration depth of individual debris particles. The utilization of a coherent, collimated illumination source in the LSL system facilitates the simultaneous measurement of impact phenomena with near-IR and UV-vis spectrograph systems. Comparison of LSL images to concurrent IR results indicates two distinctly different phenomena. A high-speed, pressure-dependent IR-emitting cloud is observed in experiments to expand at velocities much higher than the debris and ejecta phenomena observed using the LSL system. In double-plate target configurations, this phenomena is observed to interact with the rear-wall several micro-seconds before the subsequent arrival of the debris cloud. Additionally, dimensional analysis presented by Whitham for blast waves is shown to describe the pressure-dependent radial expansion of the observed IR-emitting phenomena. Although this work focuses on a single hypervelocity impact configuration, the diagnostic capabilities and techniques described can be used with a wide variety of impactors, materials, and geometries to investigate any number of engineering and scientific problems.

Análise da região 5 não traduzida (5 utr) em sequências anotadas como trans-sialidase no genoma de Trypanosoma cruzi

A transsialidase é uma glicoproteína de membrana pertencente a uma família de genes de cópia múltipla, envolvida no processo de invasão celular do Trypanosoma cruzi no hospedeiro vertebrado. Esta dissertação foi concebida com um amplo componente analítico que dependia de dados publicamente disponíveis, ou seja, as sequências oriundas do projeto genoma de T. cruzi e cDNAs de trans-sialidase depositadas no Genbank-dbEST. Este componente analítico necessitou ser complementado e ampliado com a obtenção experimental de novas sequências, a partir da metodologia baseada na transcrição reversa acoplada a PCR. Os fragmentos obtidos de cepas de T. cruzi Dm28c (T. cruzi I), Y (T. cruzi II), CL-Brener (T. cruzi II, cepa híbrida), INPA4167 (zimodema III), 3663 (zimodema III) e Colombiana (zimodema III) foram clonados, sequenciados e analisados composicionalmente. Essas sequências foram editadas e alinhadas usando-se o software CLUSTAL X. Em uma seção específica do Genbank, denominada dbEST, buscamos os cDNAs homólogos a trans-sialidase. Esta busca por similaridade foi realizada individualmente com os números de acesso referentes às seqüências supracitadas contra o dbEST utilizando o BLAST a fim de obtermos informações funcionais e evolutivas. Em seguida, desenvolvemos metodologias experimentais que nos permitiu avaliar segmentos da 5 UTR, tais como os sítios de trans-splicing adicionais ou múltiplos em TS e seus respectivos sinais (região rica em polipirimidina), variação composicional e tamanho da região das sequências entre diferentes linhagens de T. cruzi. O resultado dessa averiguação também nos mostrou a quantidade de cDNAs relacionados com a transsialidase no dbEST bem como a relação desses cDNAs com o mini-exon. As cepas do zimodema III apresentaram tamanho médio dos fragmentos de 312 bases, enquanto T. cruzi I e T. cruzi II apresentaram, respectivamente 209 e 218. Trans splicing adicional ou duplicações gênicas com mutações no sítio primário de trans splicing não parece ser um fenômeno exclusivo de algum grupo populacional, embora seja mais evidente em T. cruzi zimodema III.

Metaconcrete: Engineered aggregates for enhanced dynamic performance

This work presents the development and investigation of a new type of concrete for the attenuation of waves induced by dynamic excitation. Recent progress in the field of metamaterials science has led to a range of novel composites which display unusual properties when interacting with electromagnetic, acoustic, and elastic waves. A new structural metamaterial with enhanced properties for dynamic loading applications is presented, which is named metaconcrete. In this new composite material the standard stone and gravel aggregates of regular concrete are replaced with spherical engineered inclusions. Each metaconcrete aggregate has a layered structure, consisting of a heavy core and a thin compliant outer coating. This structure allows for resonance at or near the eigenfrequencies of the inclusions, and the aggregates can be tuned so that resonant oscillations will be activated by particular frequencies of an applied dynamic loading. The activation of resonance within the aggregates causes the overall system to exhibit negative effective mass, which leads to attenuation of the applied wave motion. To investigate the behavior of metaconcrete slabs under a variety of different loading conditions a finite element slab model containing a periodic array of aggregates is utilized. The frequency dependent nature of metaconcrete is investigated by considering the transmission of wave energy through a slab, which indicates the presence of large attenuation bands near the resonant frequencies of the aggregates. Applying a blast wave loading to both an elastic slab and a slab model that incorporates the fracture characteristics of the mortar matrix reveals that a significant portion of the supplied energy can be absorbed by aggregates which are activated by the chosen blast wave profile. The transfer of energy from the mortar matrix to the metaconcrete aggregates leads to a significant reduction in the maximum longitudinal stress, greatly improving the ability of the material to resist damage induced by a propagating shock wave. The various analyses presented in this work provide the theoretical and numerical background necessary for the informed design and development of metaconcrete aggregates for dynamic loading applications, such as blast shielding, impact protection, and seismic mitigation.

Differenzierung von Pangasius (Pangasius hypophthalmus) und Asiatischem Rotflossenwels (Hemibagrus wyckioides) durch Protein- und DNA-Analyse

In the last years farmed Pangasius (Tra-Pangasius, Pangasius hypophthalmus) from Vietnam has reached a considerable market share, whereas aquaculture of Asian Redtail Catfish (Hemibagrus wyckioides) is in its infancy. Recently it has been detected by food control authorities in Hamburg, that Pangasius fillets have been mislabelled and sold as fillets produced from Asian Redtail catfish. The necessity to improve the analytical methods for differentiation of Pangasius and Redtail Catfish prompted us to evaluate the suitability of isoelectric focusing (IEF) and DNA-analysis for identification of the two species. IEF of water soluble proteins was found to be a fast, reliable and economical method for differentiation of raw fillets of Pangasius and Redtail Catfish, as long as reference material is available. PCR-based DNA analysis was performed as follows: (i) amplification of a 464 bp segment of the cytochrome b gene; (ii) sequencing of the PCR product; (iii) comparison of the sequence with entries in GenBank using BLAST. The sequences of both species differed considerably, allowing the unequivocal differentiation between P. hypophthalmus and H. wyckioides. Kurzfassung Pangasius (Schlankwels, Tra-Pangasius, Pangasius hypophthalmus) hat sich innerhalb weniger Jahre zu einem bedeutenden Zuchtfisch entwickelt, während die Aquakultur des Asiatischen Rotflossenwelses (Hemibagrus wyckioides) in Vietnam noch in einem relativ kleinen Maßstab stattfindet. Kürzlich wurde von der Lebensmittelüberwachung in Hamburg nachgewiesen, dass im Handel erhältliche Filets mit der Deklaration „Rotflossenwels“ aus Pangasius hergestellt worden waren. Vor diesem Hintergrund wurden zwei Methoden auf ihre Eignung zur Differenzierung von Pangasius und Rotflossenwels geprüft. Es zeigte sich, dass sowohl die isoelektrische Fokussierung (IEF) wasserlöslicher Proteine als auch die PCR-basierte DNA-Analyse zur Unterscheidung beider Arten gut geeignet ist. Die IEF stellt eine schnelle und kostengünstige Untersuchungsmethode dar, die allerdings Referenzmaterial benötigt. Mit Hilfe der PCR (Polymerase-Kettenreaktion) wurde ein Abschnitt des Cytochrom b-Gens vervielfältigt und sequenziert. Die Sequenzen von P. hypophthalmus und H. wyckioides wiesen beträchtliche Unterschiede auf. Es wird diskutiert, wie sich durch Vergleich dieser Sequenzen mit Einträgen in Gendatenbanken unbekannte Proben beider Arten sicher zuordnen lassen.

Annotation of orthologous genes in Tunnus thynnus and T.albacore species

Albacore and Atlantic Bluefin tuna are two pelagic fish. Atlantic Bluefin tuna is included in the IUCN red list of threatened species and albacore is considered to be near threatened, so conservation plans are needed. However, no genomic resources are available for any of them. In this study, to better understand their transcriptome we functionally annotated orthologous genes. In all, 159 SNPs distributed in 120 contigs of the muscle transcriptome were analyzed. Genes were predicted for 98 contigs (81.2%) using the bioinformatics tool BLAST. In addition, another bioinformatics tool, BLAST2GO was used in order to achieve GO terms for the genes, in which 41 sequences were given a biological process, and 39 sequences were given a molecular process. The most repeated biological process was metabolism and it is important that no cellular process was given in any of the sequences. The most abundant molecular process was binding and very few catalytic activity processes were given. From the initial 159 SNPs, 40 were aligned with a sequence in the database after BLAST2GO was run, and were polymorphic in Atlantic Bluefin tuna and monomorphic in albacore. From these 40 SNPs, 24 were located in an open reading frame of which four were non-synonymous and 20 were synonymous and 16 were not located in a known open reading frame,. This study provides information for better understanding the ecology and evolution of these species and this is important in order to establish a proper conservation plan and an appropriate management.

Resolução numérica de escoamentos compressíveis empregando um método de partículas livre de malhas e o processamento em paralelo (CUDA)

Os métodos numéricos convencionais, baseados em malhas, têm sido amplamente aplicados na resolução de problemas da Dinâmica dos Fluidos Computacional. Entretanto, em problemas de escoamento de fluidos que envolvem superfícies livres, grandes explosões, grandes deformações, descontinuidades, ondas de choque etc., estes métodos podem apresentar algumas dificuldades práticas quando da resolução destes problemas. Como uma alternativa viável, existem os métodos de partículas livre de malhas. Neste trabalho é feita uma introdução ao método Lagrangeano de partículas, livre de malhas, Smoothed Particle Hydrodynamics (SPH) voltado para a simulação numérica de escoamentos de fluidos newtonianos compressíveis e quase-incompressíveis. Dois códigos numéricos foram desenvolvidos, uma versão serial e outra em paralelo, empregando a linguagem de programação C/C++ e a Compute Unified Device Architecture (CUDA), que possibilita o processamento em paralelo empregando os núcleos das Graphics Processing Units (GPUs) das placas de vídeo da NVIDIA Corporation. Os resultados numéricos foram validados e a eficiência computacional avaliada considerandose a resolução dos problemas unidimensionais Shock Tube e Blast Wave e bidimensional da Cavidade (Shear Driven Cavity Problem).