Solution-Combustion Synthesized Nanocrystalline Li4Ti5O12 As High-Rate Performance Li-Ion Battery Anode

Nanocrystalline Li4Ti5O12 (LTO) crystallizing in cubic spinel-phase has been synthesized by single-step-solution-combustion method in less than one minute. LTO particles thus synthesized are flaky and highly porous in nature with a surface area of 12 m(2)/g. Transmission electron micrographs indicate the primary particles to be agglomerated crystallites of varying size between 20 and 50 nm with a 3-dimensional interconnected porous network. During their galvanostatic charge-discharge at varying rates, LTO electrodes yield a capacity value close to the theoretical value of 175 mA h/g at C/2 rate. The electrodes also exhibit promising capacity retention with little capacity loss over 100 cycles at varying discharge rates together with attractive discharge-rate capabilities yielding capacity values of 140 mA h/g and 70 mA h/g at 10 and 100 C discharge rates, respectively. The ameliorated electrode-performance is ascribed to nano and highly porous morphology of the electrodes that provide short diffusion-paths for Li in conjunction with electrolyte percolation through the electrode pores ensuring a high flux of Li.

Structural and optical properties of (100-x)Li2B4O7 center dot x(Ba5Li2Ti2Nb8O30) glasses and glass nanocrystal composites

Optically clear glasses of various compositions in the system (100-x)Li2B4O7 center dot x(Ba5Li2Ti2Nb8O30) (5 <= x <= 20, in molar ratio) were fabricated by splat quenching technique. Controlled heat-treatment of the as-quenched glasses at 500 degrees C for 8 h yielded nanocrystallites embedded in the glass matrix. High Resolution Transmission Electron Microscopy (HRTEM) of these samples established the composition of the nano-crystallites to be that of Ba5Li2Ti2Nb8O30. B-11 NMR studies revealed the transformation of BO4 structural units into BO3 units owing to the increase in TiO6 and NbO6 structural units as the composition of Ba5Li2Ti2Nb8O30 increased in the glass. This, in turn, resulted in an increase in the density of the glasses. The influence of the nominal composition of the glasses and glass nanocrystal composites on optical band gap (E-opt), Urbach energy (Delta E), refractive index (n), molar refraction (R-m), optical polarizability (alpha(m)) and third order non-linear optical susceptibility (chi(3)) were studied.

Screening Cycles

We demonstrate how endogenous information acquisition in credit markets creates lending cycles when competing banks undertake their screening decisions in an uncoordinated way, thereby highlighting the role of intertemporal screening externalities induced by lending market competition as a structural source of instability. We show that uncoordinated screening behavior of competing banks may be not only the source of an important financial multiplier, but also an independent source of fluctuations inducing business cycles. The screening cycle mechanism is robust to generalizations along many dimensions such as the lending market structure, the lending rate determination and the imperfections in the screening technology.

Crystallization and preliminary X-ray crystallographic analysis of a galactose-specific lectin from Dolichos lablab

The galactose-specific lectin from the seeds of Dolichos lablab has been crystallized using the hanging-drop vapour-diffusion technique. The crystals belong to space group P1, with unit-cell parameters a = 73.99, b = 84.13, c = 93.15 angstrom, alpha = 89.92, beta = 76.01, gamma = 76.99 degrees. X-ray diffraction data to a resolution of 3.0 angstrom have been collected under cryoconditions ( 100 K) using a MAR imaging-plate detector system mounted on a rotating-anode X-ray generator. Molecular-replacement calculations carried out using the available structures of legume lectins as search models revealed that the galactose-specific lectin from D. lablab forms a tetramer similar to soybean agglutinin; two such tetramers are present in the asymmetric unit.

Continuous-cooling method of specific heat measurement in the temperature range 100-300 K

The authors have developed a simple continuous-cooling method to determine specific heat of liquids and solids in the temperature range 100-300 K. The technique employs very simple instrumentation and continuously records the sample temperature as it cools to the bath temperature through a calibrated heat link. They have obtained specific heat values which agree with the reported data to within 3% for the samples investigated. This method also facilitates easy detection of abrupt changes in specific heat, as demonstrated in the observation of glass transition in some organic glass-forming systems. The method is sensitive to the study of relaxing heat capacity in supercooled liquids.

Eri maitohappobakteerien ja niiden annostustason vaikutus säilörehun käymislaatuun ja aerobiseen stabiilisuuteen

Tämän maisterin tutkielman tarkoituksena oli testata eri maitohappobakteerien ja niiden annostustason vaikutusta säilörehun käymislaatuun ja aerobiseen stabiilisuuteen. Biologisilla säilöntäaineilla eli ympeillä säilöttyjen rehujen laatua verrattiin kontrolleina toimiviin painorehuun ja muurahaishapolla tehtyyn rehuun. Koerehut tehtiin Helsingin yliopiston Maataloustieteiden laitoksella 7.6.2010. Timotei (Phleum pratense) - nurminata (Festuca pratensis) kasvusto korjattiin tähkimisen alkuvaiheessa D-arvon ollessa 711 g/kg ka. Nurmikasvuston kuiva-ainepitoisuus oli 170 g/kg heti niiton jälkeen määritettäessä ja neljän tunnin esikuivauksen jälkeen 208 g/kg. Rehuraaka-aine jaettiin kuuteen erään, joihin lisättiin säilöntäaine. Säilöntäainekäsittelyt olivat: 1) ei säilöntäainetta (painorehu), 2) muurahaishappo (100 %:na 4 l/t), 3) Lactobacillus plantarum ja Pediococcus acidilactici 1x10? pmy/g sekä pektinaasi-, ksylanaasi- ja sellulaasientsyymi, 4) L. plantarum 1x10? pmy/g, 5) L. plantarum 1x10? pmy/g ja 6) L. plantarum ja L. buchneri 2x10? pmy/g. Rehut säilöttiin laboratoriosiiloissa kolmena rinnakkaisena. Laboratoriosiilojen lisäksi rehua säilöttiin jokaisesta säilöntäainekäsittelystä kuuteen rinnakkaiseen minisiiloon säilönnän alkuajan fermentaation ja rehujen pH:n muutoksen seuraamiseksi. Minisiiloista seurattiin kaasuntuotantoa 21 päivän ajan. Raaka-aineen koostumus ja rehujen säilönnällinen laatu sekä aerobinen stabiilisuus määritettiin. Säilörehujen kuiva-ainepitoisuus oli suhteellisen pieni (n. 210 g/kg), jotta voitiin testata biologisten säilöntäaineiden tehoa märässä rehussa. Kosteassa rehussa biologisten säilöntäaineiden toiminnan onnistuminen on haastavaa. Koska raaka-aineen sokeripitoisuus oli kuitenkin erittäin suuri (196 g/kg ka), onnistui ymppirehujen säilöntä hyvin. Kaikkien koerehujen pH oli alle 4:n. Painorehu ei täyttänyt hyvän rehun kriteerejä ammoniumtypen osalta. Muurahaishapporehu oli laadultaan tyydyttävää etikkahapon pitoisuuden osalta. Rehussa tapahtui epätyypillistä etanolikäymistä hiivojen toimesta, jonka johdosta rehussa muodostui suuri määrä kaasua säilönnän aikana. Muurahaishapporehu ei kuitenkaan lämmennyt aerobisen stabiilisuuden mittauksen aikana, johtuen todennäköisesti suuresta etikkahapon määrästä ja toisaalta pienestä sokerin määrästä. Maitohappobakteerisäilöntäaineilla saatiin käymislaadultaan parempaa säilörehua verrattuna painorehuun, lukuun ottamatta maitohappobakteeri-entsyymirehua. Entsyymilisäyksestä ei todennäköisesti ollut hyötyä rehun säilöntälaadun kannalta. Raaka-aineen suuren sokeripitoisuuden johdosta säilörehussa oli koko säilönnän ajan tarpeeksi sokeria maitohappobakteerien käytettäväksi ja sokeri toimi siten substraattina haitallisille mikrobeille tuottaen suuren etikkahappopitoisuuden. Maitohappobakteeri-entsyymiseoksella tehty rehu oli etikkahappopitoisuuden perusteella heikkolaatuista. Lactobacillus plantarumin molemmilla annostustasoilla (1x10? ja 1x10? pmy/g rehua) saatiin laadultaan hyvää rehua. Suuri sokeripitoisuus molemmissa rehuissa johtui todennäköisesti raaka-aineen tavallista suuremmasta sokerin määrästä. Molempien rehujen maitohappo-etikkahappo-suhde oli melko korkea, viitaten homofermentatiiviseen maitohappokäymiseen. Lactobacillus buchneri –lisäyksellä rehu oli säilönnälliseltä laadultaan hyvää. Heterofermentatiivisen ympin lisäys nosti tyypillisesti rehun pH:ta sekä pienensi maitohappoetikkahappo-suhdelukua verrattuna homofermentatiiviseen ymppiin. L. buchneri –lisäys paransi hieman säilörehun aerobista stabiilisuutta verrattuna homofermentatiivisella maitohappobakteerilla säilöttyyn rehuun, mutta tulos ei ollut tilastollisesti merkitsevä.

Enhancement of fatigue life of Ni-Ti-Fe shape memory alloys by thermal cycling

The effect of thermal cycling on the load-controlled tension-tension fatigue behavior of a Ni-Ti-Fe shape memory alloy (SMA) at room temperature was studied. Considerable strain accumulation was observed to occur in this alloy under both quasi-static and cyclic loading conditions. Though, in all cases, steady-state is reached within the first 50-100 cycles, the accumulated steady-state strain, epsilon(p.ss), is much smaller in thermally cycled alloy. As a result, the fatigue performance of them was found to be significantly enhanced vis-a-vis the as-solutionized alloy. Furthermore, under load-controlled conditions, the fatigue life of Ni-Ti-Fe alloys was found to be exclusively dependent on epsilon(p.ss). Observations made by profilometry and differential scanning calorimetry (DSC) indicate that the 200-500% enhancement in fatigue life of thermally cycled alloy is due to the homogeneous distribution of the accumulated fatigue strain. (C) 2010 Elsevier B.V. All rights reserved.

Microwave Irradiation Assisted Method for the Rapid Synthesis of fine Particles of alpha Al2O3 And alpha (Al1-XCrx)(2)O-3 And Their Coatings on Si(100)

Chromium substituted beta diketonate complexes of aluminium have been synthesized and employed as precursors for a novel soft chemistry process wherein microwave irradiation of a solution of the complex yields within minutes well crystallized needles of alpha (Al1 XCrx)(2)O-3 measuring 20 30 nm in diameter and 50 nm long By varying the microwave irradiation parameters and using a surfactant such as polyvinyl pyrrolidone the crystallite size and shape can be controlled and their agglomeration prevented These microstructural parameters as well as the polymorph of the Cr substituted Al2O3 formed may also be controlled by employing a different complex Samples of alpha (Al1 XCrx)(2)O-3 have been characterized by XRD FTIR and TEM The technique results in material of homogeneous metal composition, as shown by EDAX and can be adjusted as desired The technique has been extended to obtain coatings of alpha (Al1 XCrx)(2)O-3 on Si(100)

The top 100 questions of importance to the future of global agriculture

Despite a significant growth in food production over the past half-century, one of the most important challenges facing society today is how to feed an expected population of some nine billion by the middle of the 20th century. To meet the expected demand for food without significant increases in prices, it has been estimated that we need to produce 70-100 per cent more food, in light of the growing impacts of climate change, concerns over energy security, regional dietary shifts and the Millennium Development target of halving world poverty and hunger by 2015. The goal for the agricultural sector is no longer simply to maximize productivity, but to optimize across a far more complex landscape of production, rural development, environmental, social justice and food consumption outcomes. However, there remain significant challenges to developing national and international policies that support the wide emergence of more sustainable forms of land use and efficient agricultural production. The lack of information flow between scientists, practitioners and policy makers is known to exacerbate the difficulties, despite increased emphasis upon evidence-based policy. In this paper, we seek to improve dialogue and understanding between agricultural research and policy by identifying the 100 most important questions for global agriculture. These have been compiled using a horizon-scanning approach with leading experts and representatives of major agricultural organizations worldwide. The aim is to use sound scientific evidence to inform decision making and guide policy makers in the future direction of agricultural research priorities and policy support. If addressed, we anticipate that these questions will have a significant impact on global agricultural practices worldwide, while improving the synergy between agricultural policy, practice and research. This research forms part of the UK Government's Foresight Global Food and Farming Futures project.

Absorption-resorption heating cycles with the new working pairs R21-NMP and R21-DMA

The new working pairs, R21-NMP and R21-DMA, find potential application as working pairs for the single stage Resorption Heat Pump (RHP) and the Resorption Heat Transformer (RHT) cycles. A thermodynamic cycle analysis with these pairs shows that single stage RHPs have high COPs in their entire range of operation. RHTs show higher temperature boosts (up to 47 K) than the simple absorption heat transformers. Absorber temperatures of up to 400 K can be achieved in a single stage RHT system using R21 as the refrigerant. However, absorption-resorption systems have inherent limitations on the range of operating temperatures. Besides, they necessitate a higher pump work as compared to simple single stage absorption heating systems.

Electrical switching studies on Ge-Te-Tl chalcogenide glasses: Effect of thallium on the composition dependence of switching voltages

Bulk Ge(17)Te83_,JI glasses (05x.5_13), have been found to exhibit memory type electrical switching. The switching voltages (also known as threshold voltage V-th) of Ge17Te83-xTlx glasses are found to decrease with increasing thallium content. The rate of decrease of Vtry is greater at lower concentrations and \textbackslashid, falls at a slower rate for higher thallium concentrations (x 6). The addition of thallium to the Ge-Te network fragments the covalent network and introduces ionic nature to it; the reduction in network connectivity leads to the decrease in switching voltages with thallium content. The decrease in the glass transition temperatures of Ge17Te83-xTlx glasses with increasing thallium concentration supports the idea of decrease in network connectivity with TI addition. The more metallic nature of TI also contributes to the observed reduction in the switching voltages of Ge17Te83-xTlx glasses with TI content. Further, there is an interesting correlation seen between the threshold voltage V-th and the average bond energy, as a function of TI content. In addition, the switching voltages of Ge17Te83-xTlx glasses have been found to decrease with sample thickness almost linearly. The set-reset studies indicate that the Ge17Te83-xTl2 sample can be switched for more than 10 cycles, whereas other glasses could not be reset beyond two switching cycles. (C) 2010 Elsevier B.V. All rights reserved.

Substrate-dependent structure, microstructure, composition and properties of nanostructured TiN films

Titanium nitride films of a thickness of similar to 1.5 mu m were deposited on amorphous and crystalline substrates by DC reactive magnetron sputtering at ambient temperature with 100% nitrogen in the sputter gas. The growth of nanostructured, i.e. crystalline nano-grain sized, films at ambient temperature is demonstrated. The microstructure of the films grown on crystalline substrates reveals a larger grain size/crystallite size than that of the films deposited on amorphous substrates. Specular reflectance measurements on films deposited on different substrates indicate that the position of the Ti-N 2s band at 2.33 eV is substrate-dependent, indicating substrate-mediated stoichiometry. This clearly demonstrates that not only structure and microstructure, but also chemical composition of the films is substrate-influenced. The films deposited on amorphous substrates display lower hardness and modulus values than the films deposited on crystalline substrates, with the highest value of hardness being 19 GPa on a lanthanum aluminate substrate. (C) 2011 Elsevier Ltd. All rights reserved.