Heavy-metal pollution and remediation of forest soil around the Harjavalta Cu-Ni smelter, in SW Finland

Abstract

Development of MASH TL-3 Transition Between Guardrail and Portable Concrete Barriers, TPF-5(081), 2014

Often, road construction causes the need to create a work zone. In these scenarios, portable concrete barriers (PCBs) are typically installed to shield workers and equipment from errant vehicles as well as prevent motorists from striking other roadside hazards. For an existing W-beam guardrail system installed adjacent to the roadway and near the work zone, guardrail sections are removed in order to place the portable concrete barrier system. The focus of this research study was to develop a proper stiffness transition between W-beam guardrail and portable concrete barrier systems. This research effort was accomplished through development and refinement of design concepts using computer simulation with LS-DYNA. Several design concepts were simulated, and design metrics were used to evaluate and refine each concept. These concepts were then analyzed and ranked based on feasibility, likelihood of success, and ease of installation. The rankings were presented to the Technical Advisory Committee (TAC) for selection of a preferred design alternative. Next, a Critical Impact Point (CIP) study was conducted, while additional analyses were performed to determine the critical attachment location and a reduced installation length for the portable concrete barriers. Finally, an additional simulation effort was conducted in order to evaluate the safety performance of the transition system under reverse-direction impact scenarios as well as to select the CIP. Recommendations were also provided for conducting a Phase II study and evaluating the nested Midwest Guardrail System (MGS) configuration using three Test Level 3 (TL-3) full-scale crash tests according to the criteria provided in the Manual for Assessing Safety Hardware, as published by the American Association of Safety Highway and Transportation Officials (AASHTO).

Genesis of the Jurassic carbonate-hosted Pb-Zn deposits of Jebel Ressas (North-eastern Tunisia): Evidence from mineralogy, petrography and trace metal contents and isotope (O, C, S, Pb) geochemistry

The Jebel Ressas Pb-Zn deposits in North-Eastern Tunisia occur mainly as open-space fillings (lodes, tectonic breccia cements) in bioclastic limestones of the Upper Jurassic Ressas Formation and along the contact of this formation with Triassic rocks. The galena-sphalerite association and their alteration products (cerussite, hemimorphite, hydrozincite) are set within a calcite gangue. The Triassic rocks exhibit enrichments in trace metals, namely Pb, Co and Cd enrichment in clays and Pb, Zn, Cd, Co and Cr enrichment in carbonates, suggesting that the Triassic rocks have interacted with the ore-bearing fluids associated with the Jebel Ressas Pb-Zn deposits. The delta(18)O content of calcite associated with the Pb-Zn mineralization suggests that it is likely to have precipitated from a fluid that was in equilibrium with the Triassic dolostones. The delta(34)S values in galenas from the Pb-Zn deposits range from -1.5 to +11.4%, with an average of 5.9% and standard deviation of 3.9%. These data imply mixing of thermochemically-reduced heavy sulfur carried in geothermal- and fault-stress-driven deep-seated source fluid with bacterially-reduced light sulfur carried in topography-driven meteoric fluid. Lead isotope ratios in galenas from the Pb-Zn deposits are homogenous and indicate a single upper crustal source of base-metals for these deposits. Synthesis of the geochemical data with geological data suggests that the base-metal mineralization at Jebel Ressas was formed during the Serravallian-Tortonian (or Middle-Late Miocene) Alpine compressional tectonics.

Isothermal sections of the Ru-Si-Ge, Ru-Ge-Sn and Ru-Si-Sn systems at 900°C

The ternary systems Ruthenium-Silicon-Germanium, Ruthenium-Germanium-Tin and Ruthenium-Silicon-Tin were investigated by powder X-ray diffraction and electron microprobe analysis. Relations at 900 degrees C between solid phases are given and no ternary compound was found. Solubilities and evolution of lattice parameters have been correlated. Maximum mutual solubilities in the Si-Sn and Ge-Sn systems are given. (C) 1998 Elsevier Science S.A.

Freezing Point Depressions of Dilute Solutions of Alkali Metal Chlorides and Bromides

Freezing point depressions (¿Tf) of dilute solutions of several alkali metal chlorides and bromides were calculated by means of the best activity coefficient equations. In the calculations, Hückel, Hamer and Pitzer equationswere used for activity coefficients. The experimental ¿Tf values available in the literature for dilute LiCl, NaCl and KBr solutions can be predicted within experimental error by the Hückel equations used. The experimental ¿Tf values for dilute LiCl and KBr solutions can also be accurately calculated by corresponding Pitzer equations and those for dilute NaCl solutions by the Hamer equation for this salt. Neither Hamer nor Pitzer equations predict accurately the freezing points reported in the literature for LiBr and NaBr solutions. The ¿Tf values available for dilute solutions of RbCl, CsCl or CsBr are not known at the moment accurately because the existing data for these solutions are not precise. The freezing point depressions are tabulated in the present study for LiCl, NaCl and KBr solutions at several rounded molalities. The ¿Tf values in this table can be highly recommended. The activity coefficient equations used in the calculation of these values have been tested with almost allhigh-precision electrochemical data measured at 298.15 K.

Metal surface and subsurface inspection using nondestructive optical methods

This thesis considers nondestructive optical methods for metal surface and subsurface inspection. The main purpose of this thesis was to study some optical methods in order to find out their applicability to industrial measurements. In laboratory testing the simplest light scattering approach, measurement of specular reflectance, was used for surface roughness evaluation. Surface roughness, curvature and finishing process of metal sheets were determined by specular reflectance measurements. Using a fixed angleof incidence, the specular reflectance method might be automated for industrialinspection. For defect detection holographic interferometry and thermography were compared. Using either holographic interferometry or thermography, relativelysmall-size defects in metal plates could be revealed. Holographic techniques have some limitations for industrial measurements. On the contrary, thermography has excellent prospects for on-line inspection, especially with scanning techniques.

Horizontal pressures in cylindrical metal silos and comparison with different international standards

The focus of this research was to evaluate the horizontal pressures on a cylindrical metal silo of corrugated walls and flat bottom with 1.82m diameter and 5.4m high, and to compare the values with those obtained theoretically by the ISO 11697, EP 433 and AS 3774 standards. The silo was symmetrically filled and constant speed with wheat cv. soft red for two different height/diameter ratios (H/D) and was unloaded through three orifices with a diameter of 71.6mm, one concentric and two eccentrics. Horizontal pressures were measured on the walls of the silo at three positions using hydraulic type pressure cells. The results showed that shortly after the start of the unloading, there was a mass flow above the quota of H/D = 1.2, whereas below this quota funnel flow occurred. It can be said that the EP 433 standard was more appropriate to predict horizontal pressures in silos in H/D ratio = 1.0, with eccentric unloading. For the H/D ratio = 1.5, AS 3774 standard was the one that produced values closer to the experimental.

Extraction and Simultaneous Determination of Glyphosate, AMPA and Compounds of the Shikimic Acid Pathway in Plants

This study has aimed to develop a method for simultaneous extraction and determination by liquid chromatography and mass spectrometry (LC-MS/MS) of glyphosate, aminomethylphosphonic acid (AMPA), shikimic acid, quinic acid, phenylalanine, tyrosine and tryptophan. For the joint analysis of these compounds the best conditions of ionization in mass spectrometry and for chromatographic separation of the compounds were selected. Calibration curves and linearity ranges were also determined for each compound. Different extraction systems of the compounds were tested from plant tissues collected from sugarcane (Saccharum officinarum) and eucalyptus (Eucalyptus urophylla platiphylla) plants two days after the glyphosate application at the dose of 720 g a.e. ha-1. The plant material was dried in a forced air circulation drying oven and in a lyophilizer, and subsequently the extractions with acidified water (pH 2.5), acetonitrile-water (50:50) [v/v] and methanol-water (50:50) [v/v] were tested. To verify the recovery of the compounds in the plant matrix with acidified water as an extracting solution, the samples were fortified with a solution containing the mixture of the different analytical standards present so that this one presented the same levels of 50 and 100 μg L-1 of each compound. All experiments were conducted with three replicates. The analytical method developed was efficient for compounds quantifications. The extraction from the samples dried in an oven and using acidified water allowed better extraction levels for all compounds. The recovery levels of the compounds in the fortified samples with known amounts of each compound for both plants samples were rather satisfactory.

Antibacterial and anti-inflammatory activities of an extract, fractions, and compounds isolated from Gochnatia pulchra aerial parts

This paper reports on the in vitro antibacterial and in vivo anti-inflammatory properties of a hydroethanolic extract of the aerial parts of Gochnatia pulchra (HEGP). It also describes the antibacterial activity of HEGP fractions and of the isolated compounds genkwanin, scutellarin, apigenin, and 3,5-O-dicaffeoylquinic acid, as evaluated by a broth microdilution method. While HEGP and its fractions did not provide promising results, the isolated compounds exhibited pronounced antibacterial activity. The most sensitive microorganism was Streptococcus pyogenes, with minimum inhibitory concentration (MIC) values of 100, 50 and 25 µg/mL for genkwanin and the flavonoids apigenin and scutellarin, respectively. Genkwanin produced an MIC value of 25 µg/mL against Enterococcus faecalis. A paw edema model in rats and a pleurisy inflammation model in mice aided investigation of the anti-inflammatory effects of HEGP. This study also evaluated the ability of HEGP to modulate carrageenan-induced interleukin-1 beta (IL-1β), tumor necrosis factor alpha (TNF-α), and monocyte chemoattractant protein-1 (MCP-1) production. Orally administered HEGP (250 and 500 mg/kg) inhibited carrageenan-induced paw edema. Regarding carrageenan-induced pleurisy, HEGP at 50, 100, and 250 mg/kg diminished leukocyte migration by 71.43%, 69.24%, and 73.34% (P<0.05), respectively. HEGP suppressed IL-1β and MCP-1 production by 55% and 50% at 50 mg/kg (P<0.05) and 60% and 25% at 100 mg/kg (P<0.05), respectively. HEGP abated TNF-α production by macrophages by 6.6%, 33.3%, and 53.3% at 100, 250, and 500 mg/kg (P<0.05), respectively. HEGP probably exerts anti-inflammatory effects by inhibiting production of the pro-inflammatory cytokines TNF-α, IL-1β, and MCP-1.

Studies on Catalysis by Vanadia Supported On Metal Oxides

Catalysis is an essential technology in manufacturing industries. The investigation based on supported vanadia catalysts and it’s sulfated analogues. Vanadia is a transition metal oxide and is used in oxidation reactions in chemical industry. It is more active and selective catalysts on suitable supports. The work deals with preparation of vanadia incorporated tin oxide and zirconia systems by wet impregnation. Physico-chemical characterization using instrumental techniques like BET etc. The surface acidic properties were determined by the ammonia TPD studies, Perylene absorption studies and Cumene conversion reaction. The catalytic activities of the prepared systems are tested by Friedel-Crafts benzylation of arenes and Bechmann rearrangement of Cyclohexanol oxime. Here the rector reactions are relatively rare. So to test the application of the catalyst systems for the selective oxidation of cyclohexanol to cyclohexanone and finally evaluate the catalytic activity of the systems for the vapour phase oxidative dehydrogenation of Ethylbenzene, which leads to the formation of Industrially important compound ‘styrene’ is another objective of this work

Fabrication of thin films and nano columnar structures of Fe-Ni amorphous alloys and modification of its surface properties by thermal annealing and swift heavy ion irradiation for tailoring the magnetic properties

Department of Physics, Cochin University of Science and Technology

Degenerate four wave mixing in some metal phthalocyanines and naphthalocyanines

Here we report measurements of third-order susceptibility χ(3), figure of merit F defined as χ(3)/α (where α is the absorption coefficient) and second hyperpolarizability 〈γ〉 of some metal substituted phthalocyanines and a naphthalocyanine in solutions of dimethyl formamide using degenerate four wave mixing at 532 nm under nanosecond excitation. It was found that among samples investigated, bis-naphthalocyanine possessed the highest value of 〈γ〉 followed by the bis-phthalocyanine. This observation is explained on the basis that bis-naphthalocyanine followed by bis-phthalocyanine has higher degree of π electron conjugation.

Lithium Containing Complex Metal Oxides and Metal phosphates:Investigations on their synthesis and various characterizations for rechargeable lithium battery applications

The work presented in the thesis is centered around two important types of cathode materials, the spinel structured LixMn204 (x =0.8to1.2) and the phospho -oIivine structured LiMP04 (M=Fe and Ni). The spinel system LixMn204, especially LiMn204 corresponding to x= 1 has been extensively investigated to understand its structural electrical and electrochemical properties and to analyse its suitability as a cathode material in rechargeable lithium batteries. However there is no reported work on the thermal and optical properties of this important cathode material. Thermal diffusivity is an important parameter as far as the operation of a rechargeable battery is concerned. In LixMn204, the electronic structure and phenomenon of Jahn-Teller distortion have already been established theoretically and experimentally. Part of the present work is an attempt to use the non-destructive technique (NDT) of photoacoustic spectroscopy to investigate the nature of the various electronic transitions and to unravel the mechanisms leading to the phenomenon of J.T distortion in LixMn204.The phospho-olivines LiMP04 (M=Fe, Ni, Mn, Co etc) are the newly identified, prospective cathode materials offering extremely high stability, quite high theoretical specific capacity, very good cycIability and long life. Inspite of all these advantages, most of the phospho - olivines especially LiFeP04 and LiNiP04 show poor electronic conductivity compared to LixMn204, leading to low rate capacity and energy density. In the present work attempts have been made to improve the electronic conductivity of LiFeP04 and LiNiP04 by adding different weight percentage MWNT .It is expected that the addition of MWNT will enhance the electronic conductivity of LiFeP04 and LiNiP04 with out causing any significant structural distortions, which is important in the working of the lithium ion battery.

Catalysis by Polymer Supported Dendrimers, their Metal Complexes and Nanoparticle Conjugates

The present thesis has described the development of some heterogeneous catalysts based on polymer supported dendrimers. Attachment of dendrimers to crosslinked polymer produced new catalysts with combined benefits of both dendrimers and heterogeneous catalysts. These were used as heterogeneous catalysts in selected reactions. All possible attempts were taken to avoid halogenated and aromatic solvents and toxic reagents. In short the present work has dealt with development of environmental friendly catalysts based on dendrimers.