Curing studies of elastomer blends with special reference to NR/ NBR and NR/BR blends

There are a large number of commercial examples and property advantages of immiscible elastomer blends.73 Blends of natural rubber (NR) and polybutadiene (BR) have shown various advantages including heat stability, improved elasticity and abrasion resistance. Ethylene-propylene-diene-rubber (EPDM) blended with styrene-butadiene rubber (SBR) has shown improvements in ozone and chemical resistance with better compression set properties. Blends of EPDM and nitrile rubber (NBR) have been cited as a compromise for obtaining moderate oil and ozone resistance with improved low temperature properties. Neoprene (CR)/BR blends offer improved low temperature properties and abrasion resistance with better processing characteristics etc. However, in many of the commercial two-phase elastomer blends, segregation of the crosslinking agents, carbon black or antioxidants preferentially into one phase can result in failure to attain optimum properties. Soluble and insoluble compounding ingredients are found to be preferentially concentrated in one phase. The balance of optimum curing of both phases therefore presents a difficult problem. It has been the aim of this study to improve the performance of commercially important elastomer blends such as natural rubber (NR)/styrene-butadiene rubber (SBR) and natural rubber/polybutadiene rubber (BR) by industrially viable procedures

“Studies on short polyester fiber - polyurethane elastomer composite with different interfacial bonding agents”

The work presented in this thesis is regarding the development and evaluation of new bonding agents for short polyester fiber - polyurethane elastomer composites. The conventional bonding system based on hexamethylenetetramine, resorcinol and hydrated silica was not effective as a bonding agent for the composite, as the water eliminated during the formation of the RF resin hydrolysed the urethane linkages. Four bonding agents based on MDI/'I‘DI and polypropyleneglycol, propyleneglycol and glycerol were prepared and the composite recipe was optimised with respect to the cure characteristics and mechanical properties. The flow properties, stress relaxation pattern and the thermal degradation characteristics of the composites containing different bonding agents were then studied in detail to evaluate the new bonding systems. The optimum loading of resin was 5 phr and the ratio of the -01 to isocyanate was 1:1. The cure characteristics showed that the optimum combination of cure rate and processability was given by the composite with the resin based on polypropyleneglycol/ glycerol/ 4,4’diphenylmethanediisocynate (PPG/GL/MDI). From the rheological studies of the composites with and without bonding agents it was observed that all the composites showed pseudoplastic nature and the activation energy of flow of the composite was not altered by the presence of bonding agents. Mechanical properties such as tensile strength, modulus, tear resistance and abrasion resistance were improved in the presence of bonding agents and the effect was more pronounced in the case of abrasion resistance. The composites based on MDI/GL showed better initial properties while composites with resins based on MDI/PPG showed better aging resistance. Stress relaxation showed a multistage relaxation behaviour for the composite. Within the-strain levels studied, the initial rate of relaxation was higher and the cross over time was lesser for the composite containing bonding agents. The bonding agent based on MDI/PPG/GL was found to be a better choice for improving stress relaxation characteristics with better interfacial bonding. Thennogravimetirc analysis showed that the presence of fiber and bonding agents improved the thennal stability of the polyurethane elastomer marginally and it was maximum in the case of MDI / GL based bonding agents. The kinetics of degradation was not altered by the presence of bonding agents

“Studies on new base materials for microcellular soles"

The most important part of any footwear is the sole (or sole and heel) which withstands all the hannful external factors such as rouglmess of the ground or road, sharp objects, thorns and stones, heat, dampness and cold during walking. The properties desirable in soling material, therefore, would be 1. lightness 2. resistance to wear and tear for long service life 3. flexibility/softness for wearing comfort 4. thennal insulation Rubber soling surpasses all other soling materials in better performance and lower cost. Because MC sole is soft and very light, and has good abrasion resistance, flex properties and set behaviour it has become very popular all over the world and demand for better quality product is ever increasing. Due to the traditional approach adopted by the footwear industry in foot wear design, the rubber based footwear export surprisingly contributes only a small percentage. The essence of success for any industry lies in the expansion of the export market. Microcellular soles are manufactured for the last three decades without much change in the traditional design and colour pattern. In recent years domestic customers have also started demanding better quality products. In view of the changing taste of the customer and growing competition from other countries, substantial improvement in the export potential will require new base materials for regular or fashion rubber based footwears. The main objective of the present study is to develop new base materials for making MC soles with good quality, viz., light weight, durability and bright colours

Block Copolymers of Unsaturated Polyesters and Functional Elastomers

Block copolymers of unsaturated polyester were prepared by condensation polymerization of hydroxyl or carboxyl terminated liquid rubbers with maleic anhydride, phthalic anhydride, and propylene glycol. The condensate obtained was mixed with styrene monomer to get an unsaturated polyester resin formulation. In this study, copolymers of unsaturated polyesters with hydroxy terminated polybutadiene, carboxy terminated nitrile rubber, and hydroxy terminated natural rubber were prepared. Mechanical properties such as tensile strength, tensile modulus, elongation at break, toughness, impact strength, surface hardness, abrasion resistance, and water absorption were evaluated after the resin was cured in appropriate molds for comparison with the control resin. The fracture toughness and impact resistance of CTBN-modified unsaturated polyester show substantial improvement by this copolymerization without seriously affecting any other property

Analyse und Beschreibung des Innengewindefertigungsverfahrens Gewindefurchen auf Basis eines Modellversuchs

Das Gewindefurchen ist ein spanloses Fertigungsverfahren zur Herstellung von Innengewinden. Es bietet wesentliche Vorteile gegenüber der spanenden Innengewindeherstellung, wie z.B. keine Notwendigkeit zur Spanentsorgung, höhere Festigkeit der Gewindeflanken und eine erhöhte Prozessgeschwindigkeit. Um die Vorteile des Verfahrens unter wirtschaftlichen und technologischen Aspekten besser auszunutzen, bietet die Weiterentwicklung der Werkzeuggeometrie sowohl im makroskopischen als auch im mikroskopischen Bereich ein enormes Potential, welches nicht nur bezüglich der Standzeit bzw. Standmenge und Prozessgeschwindigkeit, sondern auch hinsichtlich der Qualität der erzeugten Gewinde erschlossen werden sollte. Durch die empirische Untersuchung der technischen und physikalischen Eigenschaften am Gewindefurcher sollen der Anformbereich und die Formkeilgeometrie in Abhängigkeit verschiedener Prozessparameter und Werkstoffe verbessert werden, um optimale Bearbeitungsergebnisse hinsichtlich der hergestellten Gewindefurchen und des auftretenden Verschleißes am Gewindefurcher bzw. Formkeils zu erreichen. Die Basis dieser Untersuchungen bildet ein neuartiger Modellversuch, bei dem modifizierte Gewindefurcher verwendet werden, die derart umgestaltet sind, dass von einem üblichen Gewindefurcher durch Umschleifen nur noch ein einzelner Gewindegang am Werkzeug verbleibt. Dadurch ist es möglich, in einer vergrößerten Vorbohrung mit einem Formkeil die einzelnen Umformstufen beim Gewindefurchen separat zu fertigen, die auftretenden Prozesskräfte während des Eingriffs in das Werkstück zu messen und das Bearbeitungsergebnis im Werkstück und den Verschleiß am Formkeil zu bewerten. Weiterhin wird eine rein theoretische Methode beschrieben, mit der die Berechnung der Umformkraft und darauf basierend der Furchmomente am Formkeil bzw. dem ganzen Gewindefurcher möglich ist. Durch die Kenntnis der berechneten Kräfte und Momente am einzelnen Formkeil bzw. dem Gewindefurcher kann bereits in der Konzeptionsphase eines Gewindefurchers eine Anpassung des Werkszeuges an die jeweiligen Bearbeitungsanforderungen durchgeführt werden, wodurch der Entwurf von Gewindefurchern wesentlich wirtschaftlicher realisierbar ist, als durch rein empirische Herangehensweisen.

A Log-linear model of grain size influence on the geochemistry of sediments

Sediment composition is mainly controlled by the nature of the source rock(s), and chemical (weathering) and physical processes (mechanical crushing, abrasion, hydrodynamic sorting) during alteration and transport. Although the factors controlling these processes are conceptually well understood, detailed quantification of compositional changes induced by a single process are rare, as are examples where the effects of several processes can be distinguished. The present study was designed to characterize the role of mechanical crushing and sorting in the absence of chemical weathering. Twenty sediment samples were taken from Alpine glaciers that erode almost pure granitoid lithologies. For each sample, 11 grain-size fractions from granules to clay (ø grades <-1 to >9) were separated, and each fraction was analysed for its chemical composition. The presence of clear steps in the box-plots of all parts (in adequate ilr and clr scales) against ø is assumed to be explained by typical crystal size ranges for the relevant mineral phases. These scatter plots and the biplot suggest a splitting of the full grain size range into three groups: coarser than ø=4 (comparatively rich in SiO2, Na2O, K2O, Al2O3, and dominated by “felsic” minerals like quartz and feldspar), finer than ø=8 (comparatively rich in TiO2, MnO, MgO, Fe2O3, mostly related to “mafic” sheet silicates like biotite and chlorite), and intermediate grains sizes (4≤ø <8; comparatively rich in P2O5 and CaO, related to apatite, some feldspar). To further test the absence of chemical weathering, the observed compositions were regressed against three explanatory variables: a trend on grain size in ø scale, a step function for ø≥4, and another for ø≥8. The original hypothesis was that the trend could be identified with weathering effects, whereas each step function would highlight those minerals with biggest characteristic size at its lower end. Results suggest that this assumption is reasonable for the step function, but that besides weathering some other factors (different mechanical behavior of minerals) have also an important contribution to the trend. Key words: sediment, geochemistry, grain size, regression, step function

Frost jacking of joint blocks above Cwm Idwal, in North Wales

The in situ development of ground ice is a major mechanism in rock breakdown. Where well-jointed rock has been streamlined through glacial abrasion, subsequent growth of subsurface intrusive ice may lead to the uplift of individual blocks and disruption of the ice erosional landform. This jacking' mechanism is likely to be a progressive process. Following climatic change and allied ground ice decay, the degree of subsequent settlement will be controlled by the degree to which individual blocks become wedged against their neighbours. Possibly the first example to be identified in Britain is described here. It dates from a severe phase of periglaciation occurring between the Last Glacial Maximum and the Flandrian Interglacial (c. 22-11.6 ka BP). Where identified in currently temperate regions, frost-jacked blocks may be interpreted as evidence for palaeopermafrost.

Frost jacking of joint blocks above Cwm Idwal, in North Wales

The in situ development of ground ice is a major mechanism in rock breakdown. Where well-jointed rock has been streamlined through glacial abrasion, subsequent growth of subsurface intrusive ice may lead to the uplift of individual blocks and disruption of the ice erosional landform. This jacking' mechanism is likely to be a progressive process. Following climatic change and allied ground ice decay, the degree of subsequent settlement will be controlled by the degree to which individual blocks become wedged against their neighbours. Possibly the first example to be identified in Britain is described here. It dates from a severe phase of periglaciation occurring between the Last Glacial Maximum and the Flandrian Interglacial (c. 22-11.6 ka BP). Where identified in currently temperate regions, frost-jacked blocks may be interpreted as evidence for palaeopermafrost.

Age relationships beteen low level rock platforms and the high coastal slopes in Jersey and the surrounding area.

Recent research along the coastal cliffs and embayments of Jersey has revealed new aspects of the geomorphology of the rocky shore platform and its relationship with the steep slopes that link it to the island plateau above. Specifically, a rockhead platform meets a 10-30 m high, near vertical cliff at approximately 8-10 m above Jersey Datum (J.D.= ±0 m Ordnance Datum; likewise Guernsey Datum: G.D.), slopes down-towards mid-tide levels becoming ever more deeply dissected. Generalised contours of this platform show it to be distinct from a lower tidal rockhead platform which is comparatively smooth over large areas as it undergoes continuing contemporary abrasion. This lower platform is generally separated from the higher one by low cliffs, less than a metre high at mid-tidal levels, but two to three metres at the base of the backing cliffs. Both of these platforms are shown to antedate the Last Cold Stage (Devensian) head at a number of localities and this relationship is taken to represent the general situation, not only in Jersey, but throughout the other Channel Islands and adjacent coasts of Armorica. Whether either, or both, of these two platforms are older than Marine Oxygen Isotope Substage (MOIS) 5e (Ipswichian) as well is not known. However the considerable age of the numerous and wide intertidal shore platforms of the Channel Islands and adjacent coasts of Amorica makes a greater age quite possible.

Optical thin films

Optical thin films are coatings of amorphous, crystalline or polymerized materials, in single or multiple layers, on surfaces of optical components such as lenses and mirrors. These thin film coatings are used in optics to reduce reflections from optical parts (antireflection coatings) or to provide highly reflective surfaces (dielectric mirrors), as well as to protect components against abrasion and ambient moisture.

Efficacy of Microwaves and Chlorhexidine on the Disinfection of Pacifiers and Toothbrushes: An In Vitro Study

Purpose: The purpose of this study was to evaluate, in vitro, the contamination of toothbrushes and pacifiers by Streptococcus mutans, and the efficacy of microwave and chlorhexidine for their disinfection. Methods: Sixty pacifiers and 60 toothbrushes were contaminated with S mutans and then divided into groups according to the disinfection protocol: Group 1-chlorhexidine solution; Group 2-microwave sterilization; and Group 3-sterile tap water. The devices were evaluated microbiologically as to the formation of S mutans colonies/biofilms and were examined by scanning electron microscopy. The results were submitted for statistical analysis by Friedman`s test at a 5% significance level. Results: The results of both types of evaluation showed a large number of S mutans colonies/biofilms after spraying with sterile tap water, and chlorhexidine spraying and microwaving were effective in eliminate colonies/biofilms. Groups 1 and 2 were statistically similar to each other (P>.05) and differed significantly from Group 3 (P<.05). Conclusions: The 0.12% chlorhexidine solution spray and 7 minutes of microwave irradiation were effective for disinfection of pacifiers and toothbrushes. (Pediatr Dent 2011;33:10-3) Received July 29, 2009 I Last Revision January 26, 2010 I Accepted March 10, 2010

Effect of Two Restorative Materials on Root Dentine Erosion

This study sought to evaluate the microhardness of root dentine adjacent to glass-ionomer and composite resin restorations after erosive challenge. A crossover study was performed in two phases of 4 consecutive days each. One hundred twelve bovine root dentine slabs were obtained, and standardized box-shaped cavities were prepared at center of each specimen. The prepared cavities were randomly restored with glass-ionomer cement or composite resin. The slabs were randomly assigned among 14 volunteers, which wore intraoral palatal device containing four restored root dentin slabs. Starting on the second day, half of the palatal acrylic devices were immersed extraorally in a lemonade-like carbonated soft drink for 90 s, four times daily for 3 days. Alter 3-day wash-out, dentine slabs restored with the alternative material were placed into palatal appliance and the volunteers started the second phase of this study. After erosive challenges. microhardness measurements were performed. Regardless of the restorative material employed, eroded specimens demonstrated lower microhardness value (p < 0.0001). At eroded condition examined in this study, dentine restored with glass-ionomer cement showed higher microhardness values (p < 0.0001). It may be concluded that the glass-ionomer cement decreases the progression of root dentine erosion at restoration margin. (C) 2010 Wiley Periodicals, Inc J Biomed Mater Res Part B Appl Biomater 93B 304-305, 2010

Interaction of strangelets with ordinary nuclei

Strangelets (hypothetical stable lumps of strange quarkmatter) of astrophysical origin may be ultimately detected in specific cosmic ray experiments. The initial mass distribution resulting from the possible astrophysical production sites would be subject to reprocessing in the interstellar medium and in the earth`s atmosphere. In order to get a better understanding of the claims for the detection of this still hypothetic state of hadronic matter, we present a study of strangelet-nucleus interactions including several physical processes of interest (abrasion, fusion, fission, excitation and de-excitation of the strangelets), to address the fate of the baryon number along the strangelet path. It is shown that, although fusion may be important for low-energy strangelets in the interstellar medium (thus increasing the initial baryon number A), in the earth`s atmosphere the loss of the baryon number should be the dominant process. The consequences of these findings are briefly addressed.

Neopaleozoic striated surfaces in the granitic basement and clast pavement remains of Salto, SP

Near Guarau Ceramic, localized southwest of Salto city in the State of Sao Paulo, two granite outcrops, distant some tens of meters from each other, display Neopaleozoic striated surfaces. These surfaces are in contact with diamictites from the Itarare Subgroup. The striae correspond to sub parallel grooves with millimetric spacing and depth, oriented about N48E and dipping 12 degrees to 42 degrees towards SE. Observed features and association with diamictites indicate an origin by glacial abrasion due to ice movement from southeast towards northwest. About 1.8 km east of Salto, unconsolidated material containing flat-iron-shaped and striated clasts was found on top of granite outcrops, interpreted as clasts pavement remains.

Accelerated aging of thick glass second surface silvered reflectors under sandstorm conditions

Concentrated solar power systems are expected to be sited in desert locations where the direct normal irradiation is above 1800 kWh/m2.year. These systems include large solar collector assemblies, which account for a significant share of the investment cost. Solarreflectors are the main components of these solar collector assemblies and dust/sand storms may affect their reflectance properties, either by soiling or by surface abrasion. While soiling can be reverted by cleaning, surface abrasion is a non reversible degradation.The aim of this project was to study the accelerated aging of second surface silvered thickglass solar reflectors under simulated sandstorm conditions and develop a multi-parametric model which relates the specular reflectance loss to dust/sand storm parameters: wind velocity, dust concentration and time of exposure. This project focused on the degradation caused by surface abrasion.Sandstorm conditions were simulated in a prototype environmental test chamber. Material samples (6cm x 6cm) were exposed to Arizona coarse test dust. The dust stream impactedthese material samples at a perpendicular angle. Both wind velocity and dust concentrationwere maintained at a stable level for each accelerated aging test. The total exposure time in the test chamber was limited to 1 hour. Each accelerated aging test was interrupted every 4 minutes to measure the specular reflectance of the material sample after cleaning.The accelerated aging test campaign had to be aborted prematurely due to a contamination of the dust concentration sensor. A robust multi-parametric degradation model could thus not be derived. The experimental data showed that the specular reflectance loss decreasedeither linearly or exponentially with exposure time, so that a degradation rate could be defined as a single modeling parameter. A correlation should be derived to relate this degradation rate to control parameters such as wind velocity and dust/sand concentration.The sandstorm chamber design would have to be updated before performing further accelerated aging test campaigns. The design upgrade should improve both the reliability of the test equipment and the repeatability of accelerated aging tests. An outdoor exposure test campaign should be launched in deserts to learn more about the intensity, frequencyand duration of dust/sand storms. This campaign would also serve to correlate the results of outdoor exposure tests with accelerated exposure tests in order to develop a robust service lifetime prediction model for different types of solar reflector materials.