InAs/AlGaAs quantum dot intermediate band solar cells with enlarged sub-bandgaps

In the last decade several prototypes of intermediate band solar cells (IBSCs) have been manufactured. So far, most of these prototypes have been based on InAs/GaAs quantum dots (QDs) in order to implement the IB material. The key operation principles of the IB theory are two photon sub-bandgap (SBG) photocurrent, and output voltage preservation, and both have been experimentally demonstrated at low temperature. At room temperature (RT), however, thermal escape/relaxation between the conduction band (CB) and the IB prevents voltage preservation. To improve this situation, we have produced and characterized the first reported InAs/AlGaAs QD-based IBSCs. For an Al content of 25% in the host material, we have measured an activation energy of 361 meV for the thermal carrier escape. This energy is about 250 meV higher than the energies found in the literature for InAs/GaAs QD, and almost 140 meV higher than the activation energy obtained in our previous InAs/GaAs QD-IBSC prototypes including a specifically designed QD capping layer. This high value is responsible for the suppression of the SBG quantum efficiency under monochromatic illumination at around 220 K. We suggest that, if the energy split between the CB and the IB is large enough, activation energies as high as to suppress thermal carrier escape at room temperature (RT) can be achieved. In this respect, the InAs/AlGaAs system offers new possibilities to overcome some of the problems encountered in InAs/GaAs and opens the path for QD-IBSC devices capable of achieving high efficiency at RT.

Tuning the current ratio of a CPV system to maximize the energy harvesting in a particular location

A method based on experimental data is proposed to optimize the energy harvesting of a silicone-on-glass Fresnel-lens based CPV system. It takes into account the spectral variations along the year in a particular location as well as the thermal and spectral sensitivities of the optics and solar cell. In addition, different alternatives to tune the top/middle subcells current ratio in a CPV module are analyzed and their capacity to maximize the annually produced energy is quantified.

New concepts and techniques for the development of high-efficiency concentrating photovoltaic modules

El interés por los sistemas fotovoltaicos de concentración (CPV) ha resurgido en los últimos años amparado por el desarrollo de células multiunión de muy alta eficiencia basadas en semiconductores de los grupos III-V. Estas células han permitido obtener módulos de concentración con eficiencias que prácticamente duplican las del panel plano y que llegan al 35% en los módulos récord. Esta tesis está dedicada al diseño y la implementación experimental de nuevos conceptos que permitan obtener módulos CPV que no sólo alcancen una eficiencia alta en condiciones estándar sino que, además, sean lo suficientemente tolerantes a errores de montaje, seguimiento, temperatura y variaciones espectrales para que la energía que producen a lo largo del año sea máxima. Una de las primeras cuestiones que se abordan es el diseño de elementos ópticos secundarios para sistemas cuyo primario es una lente de Fresnel y que permiten, para una concentración fija, aumentar el ángulo de aceptancia y la tolerancia del sistema. Varios secundarios reflexivos y refractivos han sido diseñados y analizados mediante trazado de rayos. En particular, utilizando óptica anidólica y basándose en el diseño de una sola etapa conocido como ‘concentrador dieléctrico que funciona por reflexión total interna‘, se ha diseñado, fabricado y caracterizado un secundario con salida cuadrada que, usado junto con una lente de Fresnel, permite alcanzar simultáneamente una elevada eficiencia, concentración y aceptancia. Además, se ha propuesto y prototipado un método alternativo de fabricación para otro de los secundarios, denominado domo, consistente en el sobremoldeo de silicona sobre células solares. Una de las características que impregna todo el trabajo realizado en esta tesis es la aproximación holística en el diseño de módulos CPV, es decir, se ha prestado especial atención al diseño conjunto de la célula y la óptica para garantizar que el sistema total alcance la mayor eficiencia posible. En este sentido muchos sistemas ópticos desarrollados en esta tesis han sido diseñados, caracterizados y optimizados teniendo en cuenta que el ajuste de corriente entre las distintas subcélulas que comprenden la célula multiunión bajo el concentrador sea muy próximo a uno. La capa antirreflectante sobre la célula funciona, en cierto modo, como interfaz entre la óptica y la célula, por lo que se ha diseñado un método de optimización de capas antirreflectantes que considera no sólo el amplio rango de longitudes de onda para el que las células multiunión son sensibles sino también la distribución angular de intensidad sobre la célula creada por la óptica de concentración. Además, la cuestión de la falta de uniformidad también se ha abordado mediante la comparación de las distribuciones espectrales y espaciales de irradiancia que crean diferentes ópticas (simuladas mediante trazado de rayos y fotografiadas) y las pérdidas de eficiencia que experimentan las células iluminadas por dichas ópticas de concentración medidas experimentalmente. El efecto de la temperatura en la óptica de concentración también ha sido objeto de estudio de esta tesis. En particular, mediante simulaciones de elementos finitos se han dado los primeros pasos para el análisis de las deformaciones que sufren los dientes de las lentes de Fresnel híbridas (vidrio-silicona), así como el cambio de índice de refracción con la temperatura y la influencia de ambos efectos sobre el funcionamiento de los sistemas. Se ha implementado un modelo que tiene por objeto considerar las variaciones ambientales, principalmente temperatura y contenido espectral de la radiación directa, así como las sensibilidades térmica y espectral de los sistemas CPV, con el fin de maximizar la energía producida por un módulo de concentración a lo largo de un año en un emplazamiento determinado. Los capítulos 5 y 6 de este libro están dedicados al diseño, fabricación y caracterización de un nuevo concepto de módulo fotovoltaico denominado FluidReflex y basado en una única etapa reflexiva con dieléctrico fluido. En este nuevo concepto la presencia del fluido aporta algunas ventajas significativas como son: un aumento del producto concentración por aceptancia (CAP, en sus siglas en inglés) alcanzable al rodear la célula con un medio cuyo índice de refracción es mayor que uno, una mejora de la eficiencia óptica al disminuir las pérdidas por reflexión de Fresnel en varias interfaces, una mejora de la disipación térmica ya que el calor que se concentra junto a la célula se trasmite por convección natural y conducción en el fluido y un aislamiento eléctrico mejorado. Mediante la construcción y medida de varios prototipos de unidad elemental se ha demostrado que no existe ninguna razón fundamental que impida la implementación práctica del concepto teórico alcanzando una elevada eficiencia. Se ha realizado un análisis de fluidos candidatos probando la existencia de al menos dos de ellos que cumplen todos los requisitos (en particular el de estabilidad bajo condiciones de luz concentrada) para formar parte del sistema de concentración FluidReflex. Por ´ultimo, se han diseñado, fabricado y caracterizado varios prototipos preindustriales de módulos FluidReflex para lo cual ha sido necesario optimizar el proceso de fabricación de la óptica multicavidad a fin de mantener el buen comportamiento óptico obtenido en la fabricación de la unidad elemental. Los distintos prototipos han sido medidos, tanto en el laboratorio como bajo el sol real, analizando el ajuste de corriente de la célula iluminada por el concentrador FluidReflex bajo diferentes distribuciones espectrales de la radiación incidente así como el excelente comportamiento térmico del módulo. ABSTRACT A renewed interest in concentrating photovoltaic (CPV) systems has emerged in recent years encouraged by the development of high-efficiency multijunction solar cells based in IIIV semiconductors that have led to CPV module efficiencies which practically double that of flat panel PV and which reach 35% for record modules. This thesis is devoted to the design and experimental implementation of new concepts for obtaining CPV modules that not only achieve high efficiency under standard conditions but also have such a wide tolerance to assembly errors, tracking, temperature and spectral variations, that the energy generated by them throughout the year is maximized. One of the first addressed issues is the design of secondary optical elements whose primary optics is a Fresnel lens and which, for a fixed concentration, allow an increased acceptance angle and tolerance of the system. Several reflective and refractive secondaries have been designed and analyzed using ray tracing. In particular, using nonimaging optics and based on the single-stage design known as ‘dielectric totally internally reflecting concentrator’, a secondary with square output has been designed, fabricated and characterized. Used together with a Fresnel lens, the secondary can simultaneously achieve high efficiency, concentration and acceptance. Furthermore, an alternative method has been proposed and prototyped for the fabrication of the secondary named dome. The optics is manufactured by direct overmolding of silicone over the solar cells. One characteristic that permeates all the work done in this thesis is the holistic approach in the design of CPV modules, meaning that special attention has been paid to the joint design of the solar cell and the optics to ensure that the total system achieves the highest attainable efficiency. In this regard, many optical systems developed in the thesis have been designed, characterized and optimized considering that the current matching among the subcells within the multijunction solar cell beneath the optics must be close to one. Antireflective coating over the cell acts, somehow, as an interface between the optics and the cell. Consequently, a method has been designed to optimize antireflective coatings that takes into account not only the broad wavelength range that multijunction solar cells are sensitive to but also the angular intensity distribution created by the concentrating optics. In addition, the issue of non-uniformity has also been addressed by comparing the spectral and spatial distributions of irradiance created by different optics (simulated by ray tracing and photographed) and the efficiency losses experienced by cells illuminated by those concentrating optics experimentally determined. The effect of temperature on the concentrating optics has also been studied in this thesis. In particular, finite element simulations have been use to analyze the deformations experienced by the facets of hybrid (silicon-glass) Fresnel lenses, the change of refractive index with temperature and the influence of both effects on the system performance. A model has been implemented which take into consideration atmospheric variations, mainly temperature and spectral content of the direct normal irradiance, as well as thermal and spectral sensitivities of systems, with the aim of maximizing the energy harvested by a CPV module throughout the year in a particular location. Chapters 5 and 6 of this book are devoted to the design, fabrication, and characterization of a new concentrator concept named FluidReflex and based on a single-stage reflective optics with fluid dielectric. In this new concept, the presence of the fluid provides some significant advantages such as: an increased concentration acceptance angle product (CAP) achievable by surrounding the cell with a medium whose refractive index is greater than one, an improvement of the optical efficiency by reducing losses due to Fresnel reflection at several interfaces, an improvement in heat dissipation as the heat concentrated near the cell is transmitted by natural convection and conduction in the fluid, and an improved electrical insulation. By fabricating and characterizing several elementary-unit prototypes it was shown that there is no fundamental reason that prevents the practical implementation of this theoretical concept reaching high efficiency. Several fluid candidates were investigated proving the existence of at least to fluids that meet all the requirements (including the stability under concentrated light) to become part of the FluidReflex concentrator. Finally, several pre-industrial FluidReflex module prototypes have been designed and fabricated. An optimization process for the manufacturing of the multicavity optics was necessary to attain such an optics quality as the one achieved by the single unit. The module prototypes have been measured, both indoors and outdoors, analyzing the current matching of the solar cells beneath the concentrator for different spectral distribution of the incident irradiance. Additionally, the module showed an excellent thermal performance.

Present and future of photovoltaic solar electricity

Introduction Crystalline silicon technology, from quartz to system Economical and environmental issues Alternatives to cristalline silicon technology Conclusions

A free real-time hourly tilted solar irradiation data Website for Europe

The engineering of solar power applications, such as photovoltaic energy (PV) or thermal solar energy requires the knowledge of the solar resource available for the solar energy system. This solar resource is generally obtained from datasets, and is either measured by ground-stations, through the use of pyranometers, or by satellites. The solar irradiation data are generally not free, and their cost can be high, in particular if high temporal resolution is required, such as hourly data. In this work, we present an alternative method to provide free hourly global solar tilted irradiation data for the whole European territory through a web platform. The method that we have developed generates solar irradiation data from a combination of clear-sky simulations and weather conditions data. The results are publicly available for free through Soweda, a Web interface. To our knowledge, this is the first time that hourly solar irradiation data are made available online, in real-time, and for free, to the public. The accuracy of these data is not suitable for applications that require high data accuracy, but can be very useful for other applications that only require a rough estimate of solar irradiation.

Integral energy performance characterization of semi-transparent photovoltaic elements for building integration under real operation conditions

In this paper, a methodology for the integral energy performance characterization (thermal, daylighting and electrical behavior) of semi-transparent photovoltaic modules (STPV) under real operation conditions is presented. An outdoor testing facility to analyze simultaneously thermal, luminous and electrical performance of the devices has been designed, constructed and validated. The system, composed of three independent measurement subsystems, has been operated in Madrid with four prototypes of a-Si STPV modules, each one corresponding to a specific degree of transparency. The extensive experimental campaign, continued for a whole year rotating the modules under test, has validated the reliability of the testing facility under varying environmental conditions. The thermal analyses show that both the solar protection and insulating properties of the laminated prototypes are lower than those achieved by a reference glazing whose characteristics are in accordance with the Spanish Technical Building Code. Daylighting analysis shows that STPV elements have an important lighting energy saving potential that could be exploited through their integration with strategies focused to reduce illuminance values in sunny conditions. Finally, the electrical tests show that the degree of transparency is not the most determining factor that affects the conversion efficiency.

Magnetic Attitude Control System for a Small Satellite. Impact on the Thermal Performance

El principal objetivo de la tesis es estudiar el acoplamiento entre los subsistemas de control de actitud y de control térmico de un pequeño satélite, con el fin de buscar la solución a los problemas relacionados con la determinación de los parámetros de diseño. Se considera la evolución de la actitud y de las temperaturas del satélite bajo la influencia de dos estrategias de orientación diferentes: 1) estabilización magnética pasiva de la orientación (PMAS, passive magnetic attitude stabilization), y 2) control de actitud magnético activo (AMAC, active magnetic attitude control). En primer lugar se presenta el modelo matemático del problema, que incluye la dinámica rotacional y el modelo térmico. En el problema térmico se considera un satélite cúbico modelizado por medio de siete nodos (seis externos y uno interno) aplicando la ecuación del balance térmico. Una vez establecido el modelo matemático del problema, se estudia la evolución que corresponde a las dos estrategias mencionadas. La estrategia PMAS se ha seleccionado por su simplicidad, fiabilidad, bajo coste, ahorrando consumo de potencia, masa coste y complejidad, comparado con otras estrategias. Se ha considerado otra estrategia de control que consigue que el satélite gire a una velocidad requerida alrededor de un eje deseado de giro, pudiendo controlar su dirección en un sistema inercial de referencia, ya que frecuentemente el subsistema térmico establece requisitos de giro alrededor de un eje del satélite orientado en una dirección perpendicular a la radiación solar incidente. En relación con el problema térmico, para estudiar la influencia de la velocidad de giro en la evolución de las temperaturas en diversos puntos del satélite, se ha empleado un modelo térmico linealizado, obtenido a partir de la formulación no lineal aplicando un método de perturbaciones. El resultado del estudio muestra que el tiempo de estabilización de la temperatura y la influencia de las cargas periódicas externas disminuye cuando aumenta la velocidad de giro. Los cambios de temperatura se reducen hasta ser muy pequeños para velocidades de rotación altas. En relación con la estrategia PMAC se ha observado que a pesar de su uso extendido entre los micro y nano satélites todavía presenta problemas que resolver. Estos problemas están relacionados con el dimensionamiento de los parámetros del sistema y la predicción del funcionamiento en órbita. Los problemas aparecen debido a la dificultad en la determinación de las características magnéticas de los cuerpos ferromagnéticos (varillas de histéresis) que se utilizan como amortiguadores de oscilaciones en los satélites. Para estudiar este problema se presenta un modelo analítico que permite estimar la eficiencia del amortiguamiento, y que se ha aplicado al estudio del comportamiento en vuelo de varios satélites, y que se ha empleado para comparar los resultados del modelo con los obtenidos en vuelo, observándose que el modelo permite explicar satisfactoriamente el comportamiento registrado. ABSTRACT The main objective of this thesis is to study the coupling between the attitude control and thermal control subsystems of a small satellite, and address the solution to some existing issues concerning the determination of their parameters. Through the thesis the attitude and temperature evolution of the satellite is studied under the influence of two independent attitude stabilization and control strategies: (1) passive magnetic attitude stabilization (PMAS), and (2) active magnetic attitude control (AMAC). In this regard the mathematical model of the problem is explained and presented. The mathematical model includes both the rotational dynamics and the thermal model. The thermal model is derived for a cubic satellite by solving the heat balance equation for 6 external and 1 internal nodes. Once established the mathematical model of the problem, the above mentioned attitude strategies were applied to the system and the temperature evolution of the 7 nodes of the satellite was studied. The PMAS technique has been selected to be studied due to its prevalent use, simplicity, reliability, and cost, as this strategy significantly saves the overall power, weight, cost, and reduces the complexity of the system compared to other attitude control strategies. In addition to that, another control law that provides the satellite with a desired spin rate along a desired axis of the satellite, whose direction can be controlled with respect to the inertial reference frame is considered, as the thermal subsystem of a satellite usually demands a spin requirement around an axis of the satellite which is positioned perpendicular to the direction of the coming solar radiation. Concerning the thermal problem, to study the influence of spin rate on temperature evolution of the satellite a linear approach of the thermal model is used, which is based on perturbation theory applied to the nonlinear differential equations of the thermal model of a spacecraft moving in a closed orbit. The results of this study showed that the temperature stabilization time and the periodic influence of the external thermal loads decreases by increasing the spin rate. However, the changes become insignificant for higher values of spin rate. Concerning the PMAS strategy, it was observed that in spite of its extended application to micro and nano satellites, still there are some issues to be solved regarding this strategy. These issues are related to the sizing of its system parameters and predicting the in-orbit performance. The problems were found to be rooted in the difficulties that exist in determining the magnetic characteristics of the ferromagnetic bodies (hysteresis rods) that are applied as damping devices on-board satellites. To address these issues an analytic model for estimating their damping efficiency is proposed and applied to several existing satellites in order to compare the results with their respective in-flight data. This model can explain the behavior showed by these satellites.

Thermal control of SUNRISE, a balloon-borne solar telescope

SUNRISE is a balloon-borne solar telescope flown with a long-duration balloon by NASA's Columbia Scientific Balloon Facility team from Esrange (Swedish Space Corporation), on 8 June 2009. SUNRISE has been a challenging mission from the thermal point of view because of its size and power dissipation. Thus, a dedicated thermal analysis has been carried out to find a solution that allows all the devices to be kept within their appropriate temperature ranges, without exceeding the allowable temperature gradients, critical for optical devices. In this article, the thermal design of SUNRISE is described. A geometrical mathematical model and a thermal mathematical model of the whole system have been set up for the different load cases in order to obtain the temperature distribution and gradients in the system. Some trade-offs have been necessary to fulfil all the thermal requirements. The thermal hardware used to achieve it is described. Finally, the temperatures obtained with the models have been compared with flight data.

Thermal control of SUNRISE, a balloon-borne solar telescope

SUNRISE is a balloon-borne solar telescope flown with a long-duration balloon by NASA's Columbia Scientific Balloon Facility team from Esrange (Swedish Space Corporation), on 8 June 2009. SUNRISE has been a challenging mission from the thermal point of view because of its size and power dissipation. Thus, a dedicated thermal analysis has been carried out to find a solution that allows all the devices to be kept within their appropriate temperature ranges, without exceeding the allowable temperature gradients, critical for optical devices. In this article, the thermal design of SUNRISE is described. A geometrical mathematical model and a thermal mathematical model of the whole system have been set up for the different load cases in order to obtain the temperature distribution and gradients in the system. Some trade-offs have been necessary to fulfil all the thermal requirements. The thermal hardware used to achieve it is described. Finally, the temperatures obtained with the models have been compared with flight data.

Energy yield determination of concentrator solar cells using laboratory measurements

The annual energy conversion efficiency is calculated for a four junction inverted metamorphic solar cell that has been completely characterized in the laboratory at room temperature using measurements fit to a comprehensive optoelectronic model of the multijunction solar cells. A simple model of the temperature dependence is used redict the performance of the solar cell under varying temperature and spectra characteristic of Golden, CO for an entire year. The annual energy conversion efficiency is calculated by integrating the predicted cell performance over the entire year. The effects of geometric concentration, CPV system thermal characteristics, and luminescent coupling are ighlighted.

Criterios técnicos del proyecto con módulos tridimensionales ligeros: las casas del Solar Decathlon 2005 y 2007

Este trabajo se ocupa de la construcción modular ligera de viviendas unifamiliares, más concretamente aborda el problema de la definición constructiva de las mismas, habida cuenta de lo poco conocido y publicado de este aspecto en particular. Dado que la construcción es fruto de la evolución, resulta de gran importancia el estudio de los antecedentes para comprender la situación actual, por ello para documentar como corresponde el estado de la técnica y de la investigación se estudiaron los antecedentes desde sus primeras manifestaciones a finales del siglo XIX hasta nuestros días. Contrariamente a las profecías de Le Corbusier y otros, la industrialización no ha llegado a la construcción ni en la forma ni en la medida que era de esperar a principios del siglo XX. Sin embargo y a pesar del relativo “fracaso” de la industrialización en convertirse en la forma mayoritaria de producir edificios, lo cierto es que algunos sistemas altamente industrializados, como lo es la construcción modular ligera, han logrado un lugar en el mercado, que en algunos países resulta cuanto menos significativo. Delimitar el estado de la técnica y la situación actual es crucial en este trabajo, toda vez que la construcción industrializada la realizan empresas, y situarse al margen de las mismas y de su producción, nos guste o no, resulta contrario al sentido común. De este modo se han identificado y documentado ejemplos como el de EE.UU. y Japón, entre otros, que resultan muy ilustrativos tanto desde la evolución como del estado actual. Del estado de la técnica y la investigación también resulta la escasez de publicación de detalles constructivos específicos de la construcción modular ligera. Es obvio que los fabricantes intentan blindarse mediante el secreto industrial, logrando que las soluciones constructivas más interesantes queden fuertemente protegidas dentro del conocimiento reservado de la empresa. De este modo un sistema que alcanza grados de prefabricación del 95%, tan atractivo e interesante para el arquitecto queda reservado al conocimiento de unos pocos dentro de las empresas. La búsqueda de mayor información sobre estos sistemas encuentra un filón indiscutible en los proyectos de las casas del concurso Solar Decathlon. En efecto, debido a las condiciones particulares de este concurso, las casas que compiten deben ser instaladas en un plazo corto, por lo que en su mayoría recurren al método de construcción modular ligera, para lograr correctamente este objetivo. Adicionalmente todos los planos de proyecto incluidos los de detalle, así como memorias de especificaciones técnicas, quedan colgadas en la Web, a libre disposición del público. De este modo se ha considerado interesante, conveniente y útil, aprovechar como fuente documental de este trabajo, aparte de lo obtenido en el estado de la técnica y la investigación, los proyectos de las casas de los concursos 2005 y 2007, que fueron las dos últimas ediciones celebradas cuando se inició esta tesis. De modo similar a esta carencia de detalles publicados se observa igualmente una falta de investigación y de metodologías adecuadas a la misma sobre soluciones y detalles constructivos propios de la construcción modular ligera. Por eso y ante la dificultad de manejar adecuadamente una información disponible pero farragosa, este trabajo ha dedicado una parte importante de su esfuerzo a la creación de una metodología adecuada a este tipo de situación. Hay que destacar que cada proyecto puede constar fácilmente de 60 a casi 200 planos, sin contar las memorias técnicas y otros documentos, tales como galerías de imágenes, etc. Por otra parte resulta útil establecer esta metodología, no solo para esta tesis, sino para futuros trabajos de investigación sobre el tema, toda vez que con posterioridad a 2007 se han celebrado nuevas ediciones del concurso con su correspondiente volumen de información disponible. La metodología del análisis de los proyectos se basa en el diseño y creación de siete fichas tipo que resumen los aspectos fundamentales del proyecto desde el punto de vista constructivo, permitiendo de este modo su rápida visualización y comprensión sin pretender exhaustividad, ya que en caso de querer profundizar en el detalle de la información siempre está el proyecto original para ello. Tras estudiar la información obtenida de los proyectos de las casas de concurso, se contrastan y discuten los resultados para obtener conocimientos de interés para el objetivo propuesto en la tesis. Se comparan los resultados procedentes del estado de la técnica y de la investigación y se obtienen las conclusiones correspondientes. De este modo ha sido posible identificar una serie de criterios técnicos de proyecto de viviendas unifamiliares realizadas mediante construcción modular ligera, que además se organizan en varios niveles, por lo que el resultado es un conjunto de criterios como germen de una futura guía o manual. Como conclusiones fundamentales de la tesis hay que destacar las metodológicas, que habilitan la extensión de este estudio a otros trabajos y la aportación original al conocimiento con la definición de una serie de criterios técnicos de proyecto de viviendas realizadas mediante construcción modular ligera, que además de mejorar esta parte del saber constructivo serán de gran ayuda a los arquitectos de cara a la reducción de errores, que a menudo derivan en mayores costes y plazos, cuando no directamente al abandono del sistema constructivo. El trabajo de la tesis se estructura en siete capítulos a saber: Capítulo 1: Introducción, donde se explica el tema de la tesis, el objetivo principal, las limitaciones y se aportan algunas definiciones. Capítulo 2: Estado de la técnica y la investigación, dentro del cual se presentan los antecedentes desde sus inicios pasando por la primera y segunda mitad del siglo XX y finalizando con el estado actual que recorre los sistemas de EE.UU, Japón, Europa, Escandinavia, centro Europa, Francia, España y algunos ejemplos de Latinoamérica. En el estado de la investigación se presentan las publicaciones tanto en revistas científicas indexadas en el JCR, como publicaciones no indexadas en las que se muestran artículos científicos, comunicaciones a congresos, documentación sobre el concurso Solar Decathlon, libros específicos y libros genéricos sobre construcción modular ligera, tesis doctorales tanto generales como específicas sobre el concurso Solar Decathlon, documentos de idoneidad técnica, páginas Web del concurso Solar Decathlon y finalmente páginas Web de empresas de construcción modular ligera y patentes. También se expresan las conclusiones parciales del capítulo así también como la justificación y los objetivos particulares. Capítulo 3: Metodología, se expone en primer lugar el planteamiento del problema, para luego desarrollar los métodos utilizados para el estudio y clasificación del transporte y de la organización modular, la relación entre la organización modular y distribución espacial, el diseño y contenido de las fichas resumen de los 38 proyectos presentados al SD2005 y SD2007, así también como la información consultada para su realización. Se explica asimismo como se realizaron las tablas comparativas partiendo de la información de las fichas. Finalmente se expresa la manera en que se trató el estudio particular de la junta entre módulos. Capítulo 4: Discusión de resultados, dónde en primer lugar se presenta la clasificación y las estrategias del transporte así también como una clasificación de la organización modular, en segundo lugar se estudian las relaciones que existen entre el sistema modular y la organización espacial. A partir de aquí se muestra el estudio de la estructura de todas las casas del SD2005 y SD2007, según el tipo y material de las zapatas, mostrando tanto tablas cuantitativas como tablas gráficas con fotos. De la misma manera se tratan los forjados, los pilares y las vigas y las cubiertas. Se estudia además el cerramiento opaco y acristalado, la cubierta y el forjado según las capas que lo componen. En el caso de las instalaciones se estudian las que son especiales, descartando las normales en este tipo de casas, como son los paneles fotovoltaicos, placas térmicas o tubos de vacío y los sistemas de almacenamiento de energía, como las baterías, presentando tablas numéricas y gráficas con fotos. El transporte se analiza según corresponda al traslado de la vivienda o al transporte de apoyo, según el tipo y la cantidad utilizado. Con respecto al montaje se diferencia en si se usó grúa o no, y en el caso de no utilizarse se muestran los métodos alternativos. Con respecto a la exploración de la organización modular se presentan la cantidad de módulos que utilizó cada casa, así como también la cuantificación de los sistemas híbridos como son elementos lineales 1D, paneles 2D. Por último se muestra el estudio detallado de la junta entre módulos 3D. Finalmente se realiza la propuesta de un conjunto de criterios técnicos de proyecto organizado en cuatro niveles: 1º nivel de criterios generales, 2º nivel sobre sistemas constructivos, 3º nivel de detalles constructivos y el 4º nivel llamado logística obras previas, transporte y montaje. Capítulo 5: Conclusiones y líneas futuras de investigación, se exponen las conclusiones generales, metodológicas, documentales y por último las de construcción modular. Finalmente se realiza una propuesta de líneas futuras de investigación. Capítulo 6: Bibliografía. Capítulo 7: Anexos, en el que se presentan todas las fichas resumen de las casas realizadas por el autor de esta tesis. Además se incluyen los casos concretos de Voisin en Francia y la TVA (Tennessee Valley Authority) en EE.UU., así como referencias de manuales genéricos de construcción ligera, medidas de transporte en España e información sobre estadísticas de viviendas en la Unión Europea. ABSTRACT This paper deals with Light Modular Construction of houses, and specifically addresses the problem of the constructive definition of the same, given how little known and published this subject has been. Since building construction is the result of evolution, it is of great importance to study its background for understanding the current situation, therefore to document the state of the art and research, its history was studied from its origins dating to the end nineteenth century to our days. Contrary to the prophecies of Le Corbusier and others, industrialization has not reached the construction neither in the form nor to the extent that it was expected in the early twentieth century. However, despite the relative "failure" of industrialization to become the major form of production for buildings, the fact is that some highly industrialized systems, such as the so called Lightweight Modular Construction, have achieved a place in the market, which in some countries is at least significant. To outline the state of the art and the current situation is crucial in this work, since industrialized construction is carried out by companies, and to step away from them and their production, whether we like it or not, it is contrary to common sense. So that, several cases have been identified and documented, such as the US and Japan examples, among others, which are very illustrative both from evolution and the current status. The state of the art and research shows also a shortage of publication of specific construction details of light modular construction. Obviously, manufacturers try to shield themselves by trade secret, making the most interesting constructive solutions remain heavily protected within the reserved knowledge of the company, so a system that reaches levels of 95% prefabrication, so attractive and interesting for the architect It is reserved to the knowledge of a few people inside the companies. The search for more information on these systems finds an invaluable reef in the projects of the Solar Decathlon houses. Indeed, due to the particular conditions of this contest, houses competing must be installed in a short time, so mostly turn to modular construction methods for this purpose to achieve properly this goal. Additionally all levels of project, including detailed and technical specifications reports are published on the Web, freely available to the general public. Thus it was considered interesting, convenient and useful to take advantage as a documentary source of this work, apart from what it were obtained in the state of the art and research, the projects of the houses of the 2005 and 2007 contests, which were the last two editions already held before this thesis was started. Similar to this lack of published details it is also observed a lack of research and methodologies adapted to the solutions and construction details of lightweight modular construction. So that, and facing the difficulty of adequately manage the available but bulky information, this work has devoted a significant part of its effort to create an appropriate methodology for this type of situation. It is noteworthy that each project can easily consist of 60 to almost 200 blueprints, not including technical reports and other documents, such as photo galleries, etc. The methodology of the analysis of the projects is based on the design and creation of seven record sheets that summarize key aspects of the project from a construction point of view, thus allowing quick watching and understanding of the project, without claiming completeness, always keeping for further information the blueprints themselves. After studying the information obtained from the projects of the competition houses, the results are compared and discussed to obtain relevant knowledge according to the objective proposed in the thesis. The results from the state of the art and research are also compared and the conclusions so obtained make possible to identify a number of technical design criteria for single family homes made using lightweight modular construction, which also have been organized at various levels, so the result is a set of criteria as a seed for a future guide or manual. Among the main conclusions of the thesis must be noted the methodological ones, that enable the extension of this study to other works and are an original contribution to knowledge with the definition of a number of technical criteria for housing projects made by light modular construction, what in addition to improving this part of the constructive knowledge will be of great help for the architects to reduce errors that often result in higher costs and delays, if not in abandonment of the construction system itself. The work of the thesis is divided into seven chapters as follows: Chapter 1: Introduction, where the topic of the thesis, the main objective, limitations and the provided definitions is explained. Chapter 2: State of the art and research, within which history is presented from the beginning through the first and second half of the twentieth century and ending with the current systems, that spans from the USA to Japan, Europe, Scandinavia, Central Europe, France, Spain and some Latin American examples. In the state of research publications are presented both on scientific journals indexed in the JCR, and non-indexed publications in which scientific articles, conference papers, information about the Solar Decathlon competition, generic and specific books on light modular construction, articles both general and specific on the Solar Decathlon competition, technical approval documents, dissertations, the Solar Decathlon Web pages and finally lightweight modular construction companies Web pages and patents. The partial conclusions of the chapter as well as the rationale and specific objectives are also expressed. Chapter 3: Methodology first of all exposes the problem statement and then develops the methods used for the study and classification of transportation and modular organization, the relationship between the modular organization and spatial distribution, design and content summary records of the 38 projects submitted to the SD2005 and SD2007, as well as information consulted for its realization. It explains equally how the comparative tables based on information from the chips were made. Finally, the way the particular study of the joint between modules is carried out is also treated. Chapter 4: Discussion, first sorting a classification of transport strategies as well as of modular organization, secondly the relationship between the modular system and the spatial organization studied is presented. From then on, the study of the structure of every house Moreover, to establish this methodology is useful not only for this thesis, but for future research on the subject, since after 2007 there have been held new editions of the contest with a corresponding volume of information available. shown in the SD2005 and SD2007 contests, depending on the type and material of the shoe, showing both quantitative tables as graphic boards with pictures is carried out. Similarly slabs, columns and beams and roofs are treated. Furthermore, the opaque and transparent façades, as well as roof and floor enclosure, according to the layers that compose them are studied. In the case of facilities there have been only addressed that which are of a special type, discarding that considered usual in this type of houses such as photovoltaic panels, thermal panels or vacuum tubes and energy storage systems such as batteries, presenting numerical and graphical tables with photos .The transportation is analyzed depending on it is used to move the house or for additional support, depending on the type and quantity of items used. Regarding assembly it has been made a difference if crane is or not used and if not, what the alternative methods are. With respect to the exploration of the modular organization, the amount of modules used in each house is presented, as well as the quantification of hybrid systems such as linear members as well as 1D, 2D panels. Finally, it has been carried out the detailed study of the joint between 3D modules. Finally it is proposed a set of technical criteria organized into four levels, 1st level of general criteria, 2nd level on building systems, 3rd level construction details and 4th level called previous works and logistics, transportation and assembly. Chapter 5: Conclusions and future research, where general, methodological, documentary and finally modular construction findings are presented. A proposal for further research is done. Chapter 6: Bibliography. Chapter 7: Annexes, in which all the record sheets of houses made by the author of this thesis are presented. Besides the specific cases of Voisin in France and TVA (Tennessee Valley Authority) in the USA, as well as general reference manuals on lightweight construction, transportation dimensions in Spain, and information on housing statistics in the European Union are included.

The isotope composition of selenium in chondrites constrains the depletion mechanism of volatile elements in solar system materials

Solar nebula processes led to a depletion of volatile elements in different chondrite groups when compared to the bulk chemical composition of the solar system deduced from the Sun's photosphere. For moderately-volatile elements, this depletion primarily correlates with the element condensation temperature and is possibly caused by incomplete condensation from a hot solar nebula, evaporative loss from the precursor dust, and/or inherited from the interstellar medium. Element concentrations and interelement ratios of volatile elements do not provide a clear picture about responsible mechanisms. Here, the abundance and stable isotope composition of the moderately- to highly-volatile element Se are investigated in carbonaceous, ordinary, and enstatite chondrites to constrain the mechanism responsible for the depletion of volatile elements in planetary bodies of the inner solar system and to define a δ(82/78)Se value for the bulk solar system. The δ(82/78)Se of the studied chondrite falls are identical within their measurement uncertainties with a mean of −0.20±0.26‰ (2 s.d., n=14n=14, relative to NIST SRM 3149) despite Se abundance depletions of up to a factor of 2.5 with respect to the CI group. The absence of resolvable Se isotope fractionation rules out a kinetic Rayleigh-type incomplete condensation of Se from the hot solar nebula or partial kinetic evaporative loss on the precursor material and/or the parent bodies. The Se depletion, if acquired during partial condensation or evaporative loss, therefore must have occurred under near equilibrium conditions to prevent measurable isotope fractionation. Alternatively, the depletion and cooling of the nebula could have occurred simultaneously due to the continuous removal of gas and fine particles by the solar wind accompanied by the quantitative condensation of elements from the pre-depleted gas. In this scenario the condensation of elements does not require equilibrium conditions to avoid isotope fractionation. The results further suggest that the processes causing the high variability of Se concentrations and depletions in ordinary and enstatite chondrites did not involve any measurable isotope fractionation. Different degrees of element depletions and isotope fractionations of the moderately-volatile elements Zn, S, and Se in ordinary and enstatite chondrites indicate that their volatility is controlled by the thermal stabilities of their host phases and not by the condensation temperature under canonical nebular conditions.

Solar thermal collectors for use in hybrid solar-biomass power plants in India

This thesis examined solar thermal collectors for use in alternative hybrid solar-biomass power plant applications in Gujarat, India. Following a preliminary review, the cost-effective selection and design of the solar thermal field were identified as critical factors underlying the success of hybrid plants. Consequently, the existing solar thermal technologies were reviewed and ranked for use in India by means of a multi-criteria decision-making method, the Analytical Hierarchy Process (AHP). Informed by the outcome of the AHP, the thesis went on to pursue the Linear Fresnel Reflector (LFR), the design of which was optimised with the help of ray-tracing. To further enhance collector performance, LFR concepts incorporating novel mirror spacing and drive mechanisms were evaluated. Subsequently, a new variant, termed the Elevation Linear Fresnel Reflector (ELFR) was designed, constructed and tested at Aston University, UK, therefore allowing theoretical models for the performance of a solar thermal field to be verified. Based on the resulting characteristics of the LFR, and data gathered for the other hybrid system components, models of hybrid LFR- and ELFR-biomass power plants were developed and analysed in TRNSYS®. The techno-economic and environmental consequences of varying the size of the solar field in relation to the total plant capacity were modelled for a series of case studies to evaluate different applications: tri-generation (electricity, ice and heat), electricity-only generation, and process heat. The case studies also encompassed varying site locations, capacities, operational conditions and financial situations. In the case of a hybrid tri-generation plant in Gujarat, it was recommended to use an LFR solar thermal field of 14,000 m2 aperture with a 3 tonne biomass boiler, generating 815 MWh per annum of electricity for nearby villages and 12,450 tonnes of ice per annum for local fisheries and food industries. However, at the expense of a 0.3 ¢/kWh increase in levelised energy costs, the ELFR increased saving of biomass (100 t/a) and land (9 ha/a). For solar thermal applications in areas with high land cost, the ELFR reduced levelised energy costs. It was determined that off-grid hybrid plants for tri-generation were the most feasible application in India. Whereas biomass-only plants were found to be more economically viable, it was concluded that hybrid systems will soon become cost competitive and can considerably improve current energy security and biomass supply chain issues in India.

Monitoring system for small sized photovoltaic power plants

This paper presents a monitoring system devoted to small sized photovoltaic (PV) power plants. The system is characterized by: a high level of integration; a low cost, when compared to the cost of the PV system to be monitored; and an easy installation in the majority of the PV plants with installed power of some kW. The system is able to collect, store, process and display electrical and meteorological parameters that are crucial when monitoring PV facilities. The identification of failures in the PV system and the elaboration of performance analysis of such facilities are other important characteristics of the developed system. The access to the information about the monitored facilities is achieved by using a web application, which was developed with a focus on the mobile devices. In addition, there is the possibility of an integration between the developed monitoring system and the central supervision system of Martifer Solar (a company focused on the development, operation and maintenance of PV systems).

Analyzing the Effect of Soiling on the Performance of a Photovoltaic System of Different Module Technologies in Kalkbult, South Africa

The fact that most of the large scale solar PV plants are built in arid and semi-arid areas where land availability and solar radiation is high, it is expected the performance of the PV plants in such locations will be affected significantly due to high cell temperature as well as due to soiling. Therefore, it is essential to study how the different PV module technologies will perform in such geographical locations to ensure a consistent and reliable power delivery over the lifetime of the PV power plants. As soiling is strongly dependent on the climatic conditions of a particular location a test station, consisted of about 24 PV modules and a well-equipped weather station, was built within the fences of Scatec’s 75 MW Kalkbult solar PV plant in South Africa. This study was performed to a better understand the effect of soiling by comparing the relative power generation by the cleaned modules to the un-cleaned modules. Such knowledge can enable more quantitative evaluations of the cleaning strategies that are going to be implemented in bigger solar PV power plants. The data collected and recorded from the test station has been analyzed at IFE, Norway using a MatLab script written for this thesis project. This thesis work has been done at IFE, Norway in collaboration with Stellenbosch University in South Africa and Scatec Solar a Norwegian independent power producer company. Generally for the polycrystalline modules it is found that the average temperature corrected efficiency during the period of the experiment has been 15.00±0.08 % and for the thin film-CdTe with ARC is 11.52% and for the thin film without ARC is about 11.13% with standard uncertainty of ±0.01 %. Besides, by comparing the initial relative average efficiency of the polycrystalline-Si modules when all the modules have been cleaned for the first time and the final relative efficiency; after the last cleaning schedule which is when all the reference modules E, F, G, and H have been cleaned for the last time it is found that poly3 performs 2 % and 3 % better than poly1 and poly16 respectively, poly13 performs 1 % better than poly15 as well as poly5 and poly12 performs 1 % and 2 % better than poly10 respectively. Besides, poly5 and poly12 performs a 9 % and 11 % better than poly7. Furthermore, there is no change in performance between poly6 and poly9 as well as poly4 and poly15. However, the increase in performance of poly3 to poly1, poly13 to poly15 as well as poly5 and poly12 to poly10 is insignificant. In addition, it is found that TF22 perform 7% better than the reference un-cleaned module TF24 and similarly; TF21 performs 7% higher than TF23. Furthermore, modules with ARC glass (TF17, TF18, TF19, and TF20) shows that cleaning the modules with only distilled water (TF19) or dry-cleaned after cleaned with distilled water(TF20) decreases the performance of the modules by 5 % and 4 % comparing to its respective reference uncleanedmodules TF17 and TF18 respectively.