Nutrients build-up and wash-off processes in urban land uses

This thesis describes outcomes of a research study conducted to investigate the nutrient build-up and wash-off processes on urban impervious surfaces. The data needed for the study was generated through a series of field investigations and laboratory test procedures. The study sites were selected in urbanised catchments to represent typical characteristics of residential, industrial and commercial land uses. The build-up and wash-off samples were collected from road surfaces in the selected study sites. A specially designed vacuum collection system and a rainfall simulator were used for sample collection. According to the data analysis, the solids build-up on road surfaces was significantly finer with more than 80% of the particles below 150 ìm for all the land uses. Nutrients were mostly associated with the particle size range below 150 ìm in both build-up and wash-off samples irrespective of type of land use. Therefore, the finer fraction of solids was the most important for the nutrient build-up and particulate nutrient wash-off processes. Consequently, the design of stormwater quality mitigation measures should target particles less than 150 ìm for the removal of nutrients irrespective of type of land use. Total kjeldahl nitrogen (TKN) was the most dominant form of nitrogen species in build-up on road surfaces. Phosphorus build-up on road surfaces was mainly in inorganic form and phosphate (PO4 3-) was the most dominant form. The nutrient wash-off process was found to be dependent on rainfall intensity and duration. Concentration of both total nitrogen and phosphorus was higher at the beginning of the rain event and decreased with the increase in rainfall duration. Consequently, in the design of stormwater quality mitigation strategies for nutrients removal, it is important to target the initial period of rain events. The variability of wash-off of nitrogen with rainfall intensity was significantly different to phosphorus wash-off. The concentration of nitrogen was higher in the wash-off for low intensity rain events compared to the wash-off for high intensity rain events. On the other hand, the concentration of phosphorus in the wash-off was high for high intensity rain events compared to low intensity rain events. Consequently, the nitrogen washoff can be defined as a source limiting process and phosphorus wash-off as a transport limiting process. This highlights the importance of taking into consideration the wash-off of low intensity rain events in the design of stormwater quality mitigation strategies targeting the nitrogen removal. All the nitrogen species in wash-off are primarily in dissolved form whereas phosphorus is in particulate form. The differences in the nitrogen and phosphorus wash-off processes is principally due to the degree of solubility, attachment to particulates, composition of total nitrogen and total phosphorus and the degree of adherence of the solids particles to the surface to which nutrients are attached. The particulate nitrogen available for wash-off is removed readily as these are mobilised as free solids particles on the surface. Phosphorus is washed-off mostly with the solids particles which are strongly adhered to the surface or as the fixed solids load. Investigation of the nitrogen wash-off process using bulk wash-off samples was in close agreement with the investigation of dissolved fraction of wash-off solids. This was primarily due to the predominant nature of dissolved nitrogen. However, the investigation of the processes which underpin phosphorus wash-off using bulk washoff samples could lead to loss of information. This is due to the composition of total phosphorus in wash-off solids and the inherent variability of the wash-off process for the different particle size ranges. This variability should preferably be taken into consideration as phosphorus wash-off is predominantly in particulate form. Therefore, care needs to be taken in the investigation of the phosphorus wash-off process using bulk wash-off samples to ensure that there is no loss of information and hence result in misleading outcomes. The investigation of different particle size ranges of wash-off solids is preferable in the interest of designing effective stormwater quality management strategies targeting phosphorus removal.

Up the junction? Exploiting knowledge-based development through supply chain and SME cluster interactions

Maximisation of Knowledge-Based Development (KBD) benefits requires effective dissemination and utilisation mechanisms to accompany the initial knowledge creation process. This work highlights the potential for interactions between Supply Chains (SCs) and Small and Medium sized Enterprise Clusters (SMECs), (including via ‘junction’ firms which are members of both networks), to facilitate such effective dissemination and utilisation of knowledge. In both these network types there are firms that readily utilise their relationships and ties for ongoing business success through innovation. The following chapter highlights the potential for such beneficial interactions between SCs and SMECs in key elements of KBD, particularly knowledge management, innovation and technology transfer. Because there has been little focus on the interactions between SCs and SMECs, particularly when firms simultaneously belong to both, this chapter examines the conduits through which information and knowledge can be transferred and utilised. It shows that each network type has its own distinct advantages in the types of information searched for and transferred amongst network member firms. Comparing and contrasting these advantages shows opportunities for both networks to leverage the knowledge sharing strengths of each other, through these ‘junctions’ to address their own weaknesses, allowing implications to be drawn concerning new ways of utilising relationships for mutual network gains.

Public health and clinical dilemmas resulting from imprecise vitamin D tests

Objective: To determine whether there are clinical and public health dilemmas resulting from the reproducibility of routine vitamin D assays. Methods: Blinded agreement studies were conducted in eight clinical laboratories using two commonly used assays to measure serum 25-hydroxyvitamin D (25(OH)D) levels in Australasia and Canada (DiaSorin Radioimmunoassay (RIA) and DiaSorin LIAISON® one). Results: Only one laboratory measured 25(OH)D with excellent precision. Replicate 25(OH)D measurements varied by up to 97% and 15% of paired results differed by more than 50%. Thirteen percent of subjects received one result indicating insufficiency [25-50 nmol/l] and another suggesting adequacy [>50 nmol/l]). Agreement ranged from poor to excellent for laboratories using the manual RIA, while the precision of the semi-automated Liaison® system was consistently poor. Conclusions: Recent interest in the relevance of vitamin D to human health has increased demand for 25(OH)D testing and associated costs. Our results suggest clinicians and public health authorities are making decisions about treatment or changes to public health policy based on imprecise data. Clinicians, researchers and policy makers should be made aware of the imprecision of current 25(OH)D testing so that they exercise caution when using these assays for clinical practice, and when interpreting the findings of epidemiological studies based on vitamin D levels measured using these assays. Development of a rapid, reproducible, accurate and robust assay should be a priority due to interest in populationbased screening programs and research to inform public health policy about the amount of sun exposure required for human health. In the interim, 25(OH)D results should routinely include a statement of measurement uncertainty.

Adiabatic compression testing - part I : historical development and evaluation of fluid dynamic processes including shock-wave considerations

Adiabatic compression testing of components in gaseous oxygen is a test method that is utilized worldwide and is commonly required to qualify a component for ignition tolerance under its intended service. This testing is required by many industry standards organizations and government agencies. This paper traces the background of adiabatic compression testing in the oxygen community and discusses the thermodynamic and fluid dynamic processes that occur during rapid pressure surges. This paper is the first of several papers by the authors on the subject of adiabatic compression testing and is presented as a non-comprehensive background and introduction.

Adiabatic compression testing - part II : background and approach to estimating severity of test methodology

Adiabatic compression testing of components in gaseous oxygen is a test method that is utilized worldwide and is commonly required to qualify a component for ignition tolerance under its intended service. This testing is required by many industry standards organizations and government agencies; however, a thorough evaluation of the test parameters and test system influences on the thermal energy produced during the test has not yet been performed. This paper presents a background for adiabatic compression testing and discusses an approach to estimating potential differences in the thermal profiles produced by different test laboratories. A “Thermal Profile Test Fixture” (TPTF) is described that is capable of measuring and characterizing the thermal energy for a typical pressure shock by any test system. The test systems at Wendell Hull & Associates, Inc. (WHA) in the USA and at the BAM Federal Institute for Materials Research and Testing in Germany are compared in this manner and some of the data obtained is presented. The paper also introduces a new way of comparing the test method to idealized processes to perform system-by-system comparisons. Thus, the paper introduces an “Idealized Severity Index” (ISI) of the thermal energy to characterize a rapid pressure surge. From the TPTF data a “Test Severity Index” (TSI) can also be calculated so that the thermal energies developed by different test systems can be compared to each other and to the ISI for the equivalent isentropic process. Finally, a “Service Severity Index” (SSI) is introduced to characterizing the thermal energy of actual service conditions. This paper is the second in a series of publications planned on the subject of adiabatic compression testing.

Determination of burn criterion for promoted combustion testing

Promoted ignition testing [1–3] is used to determine the relative flammability of metal rods in oxygen-enriched atmospheres. In these tests, a promoter is used to ignite each metal rod to start the sample burning. Experiments were performed to better understand the promoted ignition test by obtaining insight into the effect a burning promoter has on the preheating of a test sample. Test samples of several metallic materials were prepared and coupled to fast-responding thermocouples along their length. Various ignition promoters were used to ignite the test samples. The thermocouple measurements and test video were synchronized to determine temperature increase with respect to time and length along each test sample. A recommended length of test sample that must be consumed to be considered a flammable material was determined based on the preheated zone measured from these tests. This length was determined to be 30 mm (1.18 in.). Validation of this length and its rationale are presented.

Sustainability of a multimodal intervention to promote lifestyle factors associated with the prevention of cardiovascular disease in midlife Australian women : a 5-year follow-up

We evaluated sustainability of an intervention to reduce women’s cardiovascular risk factors, determined the influence of self-efficacy, and described women’s current health. We used a mixed method approach that utilized forced choice and open-ended questionnaire items about health status, habits, and self-efficacy. Sixty women, average age 61, returned questionnaires. Women in the original intervention group continued health behaviors intended to reduce cardiovascular disease (CVD) at a higher rate than the control group, supporting the feasibility of a targeted intervention built around women’s individual goals. The role of self-efficacy in behavior change is unclear. The original intervention group reported higher self-reported health.

Regulatory approaches to genetic testing in insurance

Rapid advancements in the field of genetic science have engendered considerable debate, speculation, misinformation and legislative action worldwide. While programs such as the Human Genome Project bring the prospect of seemingly miraculous medical advancements within imminent reach, they also create the potential for significant invasions of traditional areas of privacy and human dignity through laying the potential foundation for new forms of discrimination in insurance, employment and immigration regulation. The insurance industry, which has of course, traditionally been premised on discrimination as part of its underwriting process, is proving to be the frontline of this regulatory battle with extensive legislation, guidelines and debate marking its progress.

The effect of prolonged reading on visual functions and reading performance in students with low vision

This study is the first to investigate the effect of prolonged reading on reading performance and visual functions in students with low vision. The study focuses on one of the most common modes of achieving adequate magnification for reading by students with low vision, their close reading distance (proximal or relative distance magnification). Close reading distances impose high demands on near visual functions, such as accommodation and convergence. Previous research on accommodation in children with low vision shows that their accommodative responses are reduced compared to normal vision. In addition, there is an increased lag of accommodation for higher stimulus levels as may occur at close reading distance. Reduced accommodative responses in low vision and higher lag of accommodation at close reading distances together could impact on reading performance of students with low vision especially during prolonged reading tasks. The presence of convergence anomalies could further affect reading performance. Therefore, the aims of the present study were 1) To investigate the effect of prolonged reading on reading performance in students with low vision 2) To investigate the effect of prolonged reading on visual functions in students with low vision. This study was conducted as cross-sectional research on 42 students with low vision and a comparison group of 20 students with normal vision, aged 7 to 20 years. The students with low vision had vision impairments arising from a range of causes and represented a typical group of students with low vision, with no significant developmental delays, attending school in Brisbane, Australia. All participants underwent a battery of clinical tests before and after a prolonged reading task. An initial reading-specific history and pre-task measurements that included Bailey-Lovie distance and near visual acuities, Pelli-Robson contrast sensitivity, ocular deviations, sensory fusion, ocular motility, near point of accommodation (pull-away method), accuracy of accommodation (Monocular Estimation Method (MEM)) retinoscopy and Near Point of Convergence (NPC) (push-up method) were recorded for all participants. Reading performance measures were Maximum Oral Reading Rates (MORR), Near Text Visual Acuity (NTVA) and acuity reserves using Bailey-Lovie text charts. Symptoms of visual fatigue were assessed using the Convergence Insufficiency Symptom Survey (CISS) for all participants. Pre-task measurements of reading performance and accuracy of accommodation and NPC were compared with post-task measurements, to test for any effects of prolonged reading. The prolonged reading task involved reading a storybook silently for at least 30 minutes. The task was controlled for print size, contrast, difficulty level and content of the reading material. Silent Reading Rate (SRR) was recorded every 2 minutes during prolonged reading. Symptom scores and visual fatigue scores were also obtained for all participants. A visual fatigue analogue scale (VAS) was used to assess visual fatigue during the task, once at the beginning, once at the middle and once at the end of the task. In addition to the subjective assessments of visual fatigue, tonic accommodation was monitored using a photorefractor (PlusoptiX CR03™) every 6 minutes during the task, as an objective assessment of visual fatigue. Reading measures were done at the habitual reading distance of students with low vision and at 25 cms for students with normal vision. The initial history showed that the students with low vision read for significantly shorter periods at home compared to the students with normal vision. The working distances of participants with low vision ranged from 3-25 cms and half of them were not using any optical devices for magnification. Nearly half of the participants with low vision were able to resolve 8-point print (1M) at 25 cms. Half of the participants in the low vision group had ocular deviations and suppression at near. Reading rates were significantly reduced in students with low vision compared to those of students with normal vision. In addition, there were a significantly larger number of participants in the low vision group who could not sustain the 30-minute task compared to the normal vision group. However, there were no significant changes in reading rates during or following prolonged reading in either the low vision or normal vision groups. Individual changes in reading rates were independent of their baseline reading rates, indicating that the changes in reading rates during prolonged reading cannot be predicted from a typical clinical assessment of reading using brief reading tasks. Contrary to previous reports the silent reading rates of the students with low vision were significantly lower than their oral reading rates, although oral and silent reading was assessed using different methods. Although the visual acuity, contrast sensitivity, near point of convergence and accuracy of accommodation were significantly poorer for the low vision group compared to those of the normal vision group, there were no significant changes in any of these visual functions following prolonged reading in either group. Interestingly, a few students with low vision (n =10) were found to be reading at a distance closer than their near point of accommodation. This suggests a decreased sensitivity to blur. Further evaluation revealed that the equivalent intrinsic refractive errors (an estimate of the spherical dioptirc defocus which would be expected to yield a patient’s visual acuity in normal subjects) were significantly larger for the low vision group compared to those of the normal vision group. As expected, accommodative responses were significantly reduced for the low vision group compared to the expected norms, which is consistent with their close reading distances, reduced visual acuity and contrast sensitivity. For those in the low vision group who had an accommodative error exceeding their equivalent intrinsic refractive errors, a significant decrease in MORR was found following prolonged reading. The silent reading rates however were not significantly affected by accommodative errors in the present study. Suppression also had a significant impact on the changes in reading rates during prolonged reading. The participants who did not have suppression at near showed significant decreases in silent reading rates during and following prolonged reading. This impact of binocular vision at near on prolonged reading was possibly due to the high demands on convergence. The significant predictors of MORR in the low vision group were age, NTVA, reading interest and reading comprehension, accounting for 61.7% of the variances in MORR. SRR was not significantly influenced by any factors, except for the duration of the reading task sustained; participants with higher reading rates were able to sustain a longer reading duration. In students with normal vision, age was the only predictor of MORR. Participants with low vision also reported significantly greater visual fatigue compared to the normal vision group. Measures of tonic accommodation however were little influenced by visual fatigue in the present study. Visual fatigue analogue scores were found to be significantly associated with reading rates in students with low vision and normal vision. However, the patterns of association between visual fatigue and reading rates were different for SRR and MORR. The participants with low vision with higher symptom scores had lower SRRs and participants with higher visual fatigue had lower MORRs. As hypothesized, visual functions such as accuracy of accommodation and convergence did have an impact on prolonged reading in students with low vision, for students whose accommodative errors were greater than their equivalent intrinsic refractive errors, and for those who did not suppress one eye. Those students with low vision who have accommodative errors higher than their equivalent intrinsic refractive errors might significantly benefit from reading glasses. Similarly, considering prisms or occlusion for those without suppression might reduce the convergence demands in these students while using their close reading distances. The impact of these prescriptions on reading rates, reading interest and visual fatigue is an area of promising future research. Most importantly, it is evident from the present study that a combination of factors such as accommodative errors, near point of convergence and suppression should be considered when prescribing reading devices for students with low vision. Considering these factors would also assist rehabilitation specialists in identifying those students who are likely to experience difficulty in prolonged reading, which is otherwise not reflected during typical clinical reading assessments.

Discount rates in disarray : evidence on flawed goodwill impairment testing

Carlin and Finch, this issue, compare goodwill impairment discount rates used by a sample of large Australian firms with ‘independently’ generated discount rates. Their objective is to empirically determine whether managers opportunistically select goodwill discount rates subsequent to the 2005 introduction of International Financial Reporting Standards (IFRS) in Australia. This is a worthwhile objective given that IFRS introduced an impairment regime, and within this regime, discount rate selection plays a key role in goodwill valuation decisions. It is also timely to consider the goodwill valuation issue. Following the recent downturn in the economy, there is a high probability that many firms will be forced to write down impaired goodwill arising from boom period acquisitions. Hence, evidence of bias in rate selection is likely to be of major concern to investors, policymakers and corporate regulators. Carlin and Finch claim their findings provide evidence of such bias. In this commentary I review the validity of their claims.

Do strategy choices matter for nascent firms? A study on effectuation and causation impacts on new ventures outcomes

Principal Topic : Nascent entrepreneurship has drawn the attention of scholars in the last few years (Davidsson, 2006, Wagner, 2004). However, most studies have asked why firms are created focussing on questions such as what are the characteristics (Delmar and Davidsson, 2000) and motivations (Carter, Gartner, Shaver & Reynolds, 2004) of nascent entrepreneurs, or what are the success factors in venture creation (Davidsson & Honig; 2003; Delmar and Shane, 2004). In contrast, the question of how companies emerge is still in its infancy. On a theoretical side, effectuation, developed by Sarasvathy (2001) offers one view of the strategies that may be at work during the venture creation process. Causation, the theorized inverse to effectuation, may be described as a rational reasoning method to create a company. After a comprehensive market analysis to discover opportunities, the entrepreneur will select the alternative with the higher expected return and implement it through the use of a business plan. In contrast, effectuation suggests that the future entrepreneur will develop her new venture in a more iterative way by selecting possibilities through flexibility and interaction with the market, affordability of loss of resources and time invested, development of pre-commitments and alliances from stakeholders. Another contrasting point is that causation is ''goal driven'' while an effectual approach is ''mean driven'' (Sarasvathy, 2001) One of the predictions of effectuation theory is effectuation is more likely to be used by entrepreneurs early in the venture creation process (Sarasvathy, 2001). However, this temporal aspect and the impact of the effectuation strategy on the venture outcomes has so far not been systematically and empirically tested on large samples. The reason behind this research gap is twofold. Firstly, few studies collect longitudinal data on emerging ventures at an early enough stage of development to avoid severe survivor bias. Second, the studies that collect such data have not included validated measures of effectuation. The research we are conducting attempts to partially fill this gap by combining an empirical investigation on a large sample of nascent and young firms with the effectuation/causation continuum as a basis (Sarasvathy, 2001). The objectives are to understand the strategies used by the firms during the creation process and measure their impacts on the firm outcomes. Methodology/Key Propositions : This study draws its data from the first wave of the CAUSEE project where 28,383 Australian households were randomly contacted by phone using a specific methodology to capture emerging firms (Davidsson, Steffens, Gordon, Reynolds, 2008). This screening led to the identification of 594 nascent ventures (i.e., firms that are not operating yet) and 514 young firms (i.e., firms that have started operating from 2004) that were willing to participate in the study. Comprehensive phone interviews were conducted with these 1108 ventures. In a likewise comprehensive follow-up 12 months later, 80% of the eligible cases completed the interview. The questionnaire contains specific sections designed to distinguish effectual and causal processes, innovation, gestation activities, business idea changes and ventures outcomes. The effectuation questions are based on the components of effectuation strategy as described by Sarasvathy (2001) namely: flexibility, affordable loss and pre-commitment from stakeholders. Results from two rounds of pre-testing informed the design of the instrument included in the main survey. The first two waves of data have will be used to test and compare the use of effectuation in the venture creation process. To increase the robustness of the results, temporal use of effectuation will be tested both directly and indirectly. 1. By comparing the use of effectuation in nascent and young firms from wave 1 to 2, we will be able to find out how effectuation is affected by time over a 12-month duration and if the stage of venture development has an impact on its use. 2. By comparing nascent ventures early in the creation process versus nascent ventures late in the creation process. Early versus late can be determined with the help of time-stamped gestation activity questions included in the survey. This will help us to determine the change on a small time scale during the creation phase of the venture. 3. By comparing nascent firms to young (already operational) firms. 4. By comparing young firms becoming operational in 2006 with those first becoming operational in 2004. Results and Implications : Wave 1 and 2 data have been completed and wave 2 is currently being checked and 'cleaned'. Analysis work will commence in September, 2009. This paper is expected to contribute to the body of knowledge on effectuation by measuring quantitatively its use and impact on nascent and young firms activities at different stages of their development. In addition, this study will also increase the understanding of the venture creation process by comparing over time nascent and young firms from a large sample of randomly selected ventures. We acknowledge the results from this study will be preliminary and will have to be interpreted with caution as the changes identified may be due to several factors and may not only be attributed to the use/not use of effectuation. Meanwhile, we believe that this study is important to the field of entrepreneurship as it provides some much needed insights on the processes used by nascent and young firms during their creation and early operating stages.

Up the e-learning curve : ensuring quality online education within an Australian university

The paper describes the implementation of a project within Australian Catholic University designed to launch the Faculties into online education in a manner which ensured quality in all aspects of the teaching-learning experiences of academics and students. Key elements of the strategic approach adopted by the project leaders, including the involvement of a specialist commercial provider of web-based delivery systems as a partner in the project, mechanisms to support the initiative through the first stages, careful choice of the programs offered online, and staff development matched to the emerging needs of those involved in the teaching of courses, are described. Challenges encountered in the implementation process, and the factors which assisted in overcoming these problems are identified. The paper draws upon this experience to raise some important issues relevant to the successful introduction of online education as an integral component of the teaching repertoire of Faculties.

Will the Australian national curriculum up the intellectual ante in classrooms?

A critical review of the current and potential impacts of the Australian National Curriculum on the enacted curriculum in primary schools, with specific attention to issues of equity and social justice.

A biomechanical study of top screw pullout in anterior scoliosis correction constructs

Study Design: Biomechanical testing of vertebral body screw pullout resistance with relevance to top screw pullout in endoscopic anterior scoliosis constructs. Objectives: To analyse the effect of screw positioning and angulation on pullout resistance of vertebral body screws, where the pullout takes place along a curved path as occurs in anterior scoliosis constructs. Summary of Background Data: Top screw pullout is a significant clinical problem in endoscopic anterior scoliosis surgery, with rates of up to 18% reported in the literature. Methods: A custom designed biomechanical test rig was used to perform pullout tests of Medtronic anterior vertebral screws where the pullout occurred along an arc of known radius. Using synthetic bone blocks, a range of pullout radii and screw angulations were tested, in order to determine an ‘optimal’ configuration. The optimal configuration was then compared with standard screw positioning using a series of tests on ovine vertebrae (n=29). Results: Screw angulation has a small but significant effect on pullout resistance, with maximum strength being achieved at 10 degree cephalad angulation. Combining 10 degree cephalad angulation with maximal spacing between the top two screws (maximum pullout radius) increased the pullout resistance by 88% compared to ‘standard’ screw positioning (screws inserted perpendicular to rod at mid-body height). Conclusions: The positioning of the top screw in anterior scoliosis constructs can significantly alter its pullout resistance.