Natural Convection Heat Transfer From an Isothermal Vertical Surface to a Stable Thermally Stratified Fluid

Natural convection from an isothermal vertical surface to a thermally stratified fluid is studied numerically. A wide range of stratification levels is considered. It is shown that at high levels of ambient thermal stratification, a portion at the top of the plate absorbs heat, while a horizontal plume forms around a location where the plate temperature equals the ambient temperature. The plume is shown to be inherently unsteady, and its transient nature is investigated in detail. The effect of the temperature defect in striating the plume is discussed. Average Nusselt number data are presented for Pr = 6.0 and 0.7.

Hydrography and circulation in the western Bay of Bengal during the northeast monsoon

The Bay of Bengal, a semienclosed tropical basin that comes under the influence of monsoonal wind and freshwater influx, is distinguished by a strongly stratified surface layer and a seasonally reversing circulation. We discuss characteristics of these features in the western Bay during the northeast monsoon, when the East India Coastal Current (EICC) flows southward, using hydrographic data collected during December 1991. Vertical profiles show uniform temperature and salinity in a homogeneous surface layer, on average, 25 m deep but shallower northward and coastward. The halocline, immediately below, is approximately 50 m thick; salinity changes by approximately 3 parts per thousand. About two thirds of the profiles show temperature inversions in this layer. Salinity below the halocline hardly changes, and stratification is predominantly due to temperature variation, The halocline is noticeably better developed and the surface homogeneous layer is thinner in a low-salinity plume that hugs the coastline along the entire east coast of India, The plume is, on average, 50 km wide, with isohalines sloping down toward the coast. Most prominent in the geostrophic velocity field is the equatorward EICC. Its transport north of about 13 degrees N, computed with 1000 dbar as the level of reference, varies between 2.6 and 7.1 x 10(6) m(3) s(-1); just south of this latitude, a northwestward flow from offshore recurves and merges with the coastal current. At the southern end of the region surveyed, the transport is 7.7 x 10(6) m(3) s(-1). Recent model studies lead us to conclude that the EICC during the northeast monsoon is driven by winds along the east coast of India and Ekman pumping in the interior bay. In the south, Ekman pumping over the southwestern bay is responsible for the northwestward flow that merges with the EICC.

Role of silver doping in oxygen incorporation of oxide thin film

A distinctive characteristic of silver in oxygen incorporation of oxide thin films during pulsed laser ablation has been discovered. Optical emission spectroscopy studies of laser-induced plume of Ag-target indicates the presence of AgO species whose concentration increases with an increase in oxygen partial pressure. The formation of AgO in laser-plume has been found to be very useful for the realization of high temperature superconducting YBa2Cu3O7-delta (YBCO) and giant magnetoresistive La0.7MnO3-delta (LMO) thin films with dramatically superior quality if the target materials contained a small amount of silver. The improvement in the quality of these films is brought about by the supply of atomic oxygen to oxide lattices during their formation. This becomes possible due to the fact that Ag, after it is ablated with other constituent materials in the target, gets moderately oxidized in an oxygen atmosphere and the oxidized species dissociate back into Ag and nascent O at the substrate surface. The nascent oxygen is very highly reactive and is easily assimilated into the lattice of these compounds. (C) 1997 Elsevier Science S.A.

Longwave radiative forcing of Indian Ocean tropospheric aerosol

A spectrally resolved discrete-ordinates radiative transfer model is used to calculate the change in downwelling surface and top-of-the-atmosphere (TOA) outgoing longwave (3.9-500 mum) radiative fluxes induced by tropospheric aerosols of the type observed over the Indian Ocean during the Indian Ocean Experiment (INDOEX). Both external and internal aerosol mixtures were considered. Throughout the longwave, the aerosol volume extinction depends more strongly on relative humidity than in most of the shortwave (0.28-3.9 mum), implying that particle growth factors and realistic relative humidity profiles must be taken into account when modeling the longwave radiative effects of aerosols. A typical boundary layer aerosol loading, with a 500-nm optical depth of 0.3, will increase the downwelling longwave flux at the surface by 7.7 W m(-2) over the clean air case while decreasing the outgoing longwave radiation by 1.3 W m(-2). A more vertically extended aerosol loading, exhibiting a high opacity plume between 2 and 3 km above the surface and having a typical 500-nm optical depth of 0.7, will increase the downwelling longwave flux at the surface by 11.2 W m(-2) over the clean air case while decreasing the outgoing longwave radiation by 2.7 W m(-2). For a vertically extended aerosol profile, approximately 30% of the TOA radiative forcing comes from sea salt and approximately 60% of the forcing comes from the combination of sea salt and dust. The remaining forcing is from anthropogenic constituents. These results are for the external mixture. For an internal mixture, TOA longwave forcings can be up to a factor of two larger. Therefore, to complete our understanding of this region's longwave aerosol radiative properties, more detailed information is needed about aerosol mixing states. These longwave radiative effects partially offset the large shortwave aerosol radiative forcing and should be included in regional and global climate modeling simulations.

Laboratory simulations show diabatic heating drives cumulus-cloud evolution and entrainment

Clouds are the largest source of uncertainty in climate science, and remain a weak link in modeling tropical circulation. A major challenge is to establish connections between particulate microphysics and macroscale turbulent dynamics in cumulus clouds. Here we address the issue from the latter standpoint. First we show how to create bench-scale flows that reproduce a variety of cumulus-cloud forms (including two genera and three species), and track complete cloud life cycles-e.g., from a ``cauliflower'' congestus to a dissipating fractus. The flow model used is a transient plume with volumetric diabatic heating scaled dynamically to simulate latent-heat release from phase changes in clouds. Laser-based diagnostics of steady plumes reveal Riehl-Malkus type protected cores. They also show that, unlike the constancy implied by early self-similar plume models, the diabatic heating raises the Taylor entrainment coefficient just above cloud base, depressing it at higher levels. This behavior is consistent with cloud-dilution rates found in recent numerical simulations of steady deep convection, and with aircraft-based observations of homogeneous mixing in clouds. In-cloud diabatic heating thus emerges as the key driver in cloud development, and could well provide a major link between microphysics and cloud- scale dynamics.

Length of near-wall plumes in turbulent convection

We present planforms of line plumes formed on horizontal surfaces in turbulent convection, along with the length of line plumes measured from these planforms, in a six decade range of Rayleigh numbers (10(5) < Ra < 10(11)) and at three Prandtl numbers (Pr = 0.7, 5.2, 602). Using geometric constraints on the relations for the mean plume spacings, we obtain expressions for the total length of near-wall plumes on horizontal surfaces in turbulent convection. The plume length per unit area (L(p)/A), made dimensionless by the near-wall length scale in turbulent convection (Z(w)), remains constant for a given fluid. The Nusselt number is shown to be directly proportional to L(p)H/A for a given fluid layer of height H. The increase in Pr has a weak influence in decreasing L(p)/A. These expressions match the measurements, thereby showing that the assumption of laminar natural convection boundary layers in turbulent convection is consistent with the observed total length of line plumes. We then show that similar relationships are obtained based on the assumption that the line plumes are the outcome of the instability of laminar natural convection boundary layers on the horizontal surfaces.

Planform structure of turbulent free convection on horizontal surfaces

The planform structure of turbulent free convection over a heated horizontal surface has been visualized and analyzed for different boundary conditions at the top and for different aspect ratios, for flux Rayleigh numbers ranging from 10 exp 8 - 10 exp 10. The different boundary conditions correspond to Rayleigh-Benard convection, open convection with evaporation at the top and with an imposed external flow on the heated boundary. Without the external flow the planform is one randomly oriented line plume. At large Ra, these line plumes seem to align along the diagonal, persumably due to a large-scale flow along as visualized in the side view. When the external flow is imposed, the line plumes clearly align in the direction of external flow. Flow visualization reveals that at these Ra, the shear tends to break the plumes which otherwise would reach the opposite boundary. (Author)

Cumulus clouds and convective boundary layers: a tropical perspective on two turbulent shear flows

This paper is a review prepared for the second Marseille Colloquium on the mechanics of turbulence, held in 2011, 50 years after the first. The review covers recent developments in our understanding of the large-scale dynamics of cumulus cloud flows and of the atmospheric boundary layer in the low-wind convective regime that is often encountered in the tropics. It has recently been shown that a variety of cumulus cloud forms and life cycles can be experimentally realized in the laboratory, with the transient diabatic plume taken as the flow model for a cumulus cloud. The plume is subjected to diabatic heating scaled to be dynamically similar to heat release from phase changes in clouds. The experiments are complemented by exact numerical solutions of the Navier-Stokes-Boussinesq equations for plumes with scaled off-source heating. The results show that the Taylor entrainment coefficient first increases with heating, reaches a positive maximum and then drops rapidly to zero or even negative values. This reduction in entrainment is a consequence of structural changes in the flow, smoothing out the convoluted boundaries in the non-diabatic plume, including the tongues engulfing the ambient flow. This is accompanied by a greater degree of mixedness in the core flow because of lower dilution by the ambient fluid. The cloud forms generated depend strongly on the history of the diabatic heating profile in the vertical direction. The striking effects of heating on the flow are attributable to the operation of the baroclinic torque due to the temperature field. The mean baroclinic torque is shown to peak around a quasi-cylindrical sheet situated midway between the axis of the flow and the edges. This torque is shear-enhancing and folds down the engulfment tongues. The increase in mixedness can be traced to an explosive growth in the enstrophy, triggered by a strong fluctuating baroclinic torque that acts as a source, especially at the higher wave numbers, thus enhancing the mixedness. In convective boundary layers field measurements show that, under conditions prevailing in the tropics, the eddy fluxes of momentum and energy do not follow the Monin-Obukhov similarity. Instead, the eddy momentum flux is found to be linear in the wind speed at low winds; and the eddy heat flux is, to a first approximation, governed by free convection laws, with wind acting as a small perturbation on a regime of free convection. A new boundary layer code, based on heat flux scaling rather than wall-stress scaling, shows promising improvements in predictive skills of a general circulation model.

Review on atomization and sprays of biofuels for IC engine applications

Ever increasing energy requirements, environmental concerns and energy security needs are strongly influencing engine researchers to consider renewable biofuels as alternatives to fossil fuels. Spray process being important in IC engine combustion, existing literature on various biofuel sprays is reviewed and summarized. Both experimental and computational research findings are reviewed in a detailed manner for compression ignition (CI) engine sprays and briefly for spark ignition (SI) engine sprays. The physics of basic atomization process of sprays from various injectors is included to highlight the most recent research findings followed by discussion highlighting the effect of physico-chemical properties on spray atomization for both biofuels and fossil fuels. Biodiesel sprays are found to penetrate faster and haw narrow spray plume angle and larger droplet sizes compared to diesel. Results of analytical and computational models are shown to be useful in shedding light on the actual process of atomization. However, further studies on understanding primary atomization and the effect of fuel properties on primary atomization are required. As far as secondary atomization is concerned, changes in regimes are observed to occur at higher air-jet velocities for biodiesel compared to those of diesel. Evaporating sprays revealed that the liquid length is longer for biodiesel. Pure plant oil sprays with potential use in CI engines may require alternative injector technology due to slower breakup as compared to diesel. Application of ethanol to gasoline engines may be feasible without any modifications to port fuel injection (PFI) engines. More studies are required on the application of alternative fuels to high pressure sprays used in Gasoline Direct Injection (GDI) engines.

Tectonic inheritance of the Indian Shield: New insights from its elastic thickness structure

A new evaluation of the elastic thickness (Te) structure of the Indian Shield, derived from isotropic fan wavelet methodology, documents spatial variations of lithospheric deformation in different tectonic provinces correlated with episodic tectono-thermal events. The Te variations corroborated by shear velocity, crustal thickness, and seismogenic thickness reveal the heterogeneous rheology of the Indian lithosphere. The thinned, attenuated lithosphere beneath Peninsular India is considered to be the reason for its mechanically weak strength (<30 km), where a decoupled crust-mantle rheology under different surface/subsurface loading structures may explain the prominent low Te patterns. The arcuate Te structure of the Western Dharwar province and a NNE-trending band of low Te anomaly in the Southern Granulite Terrane are intriguing patterns. The average Te values (40-50 km) of the Central Indian Tectonic Zone, the Bastar Craton, and the northern Eastern Ghats Mobile Belt are suggestive of old, stable, Indian lithosphere, which was not affected by any major tectono-thermal events after cratonic stabilization. We propose that the anomalously high Te (60-85 km) and high S-wave velocity zone to the north of the Narmada-Son Lineament, mainly in NW Himalaya, and the northern Aravalli and Bundelkhand Cratons, suggest that Archean lithosphere characterized by a high velocity mantle keel supports the orogenic topographic loads in/near the Himalaya. The Te map clearly segments the volcanic provinces of the Indian Shield, where the signatures of the Reunion, Marion, and Kerguelen hotspots are indicated by significantly low Te patterns that correlate with plume- and rift-related thermal and mechanical rejuvenation, magmatic underplating, and crustal necking. The correlations between Te variations and the occurrence of seismicity over seismically active zones reveal different causal relationships, which led to the current seismogenic zonation of the Indian Shield. (C) 2013 Elsevier B.V. All rights reserved.

Neoarchean continental growth through arc magmatism in the Nilgiri Block, southern India

The formation and growth of continental crust in the Archean have been evaluated through models of subduction-accretion and mantle plume. The Nilgiri Block in southern India exposes exhumed Neoarchean lower crust, uplifted to heights of 2500 m above sea level along the north western margin of the Peninsula. Major lithologies in this block include charnockite with or without garnet, anorthosite-gabbro suite, pyroxenite, amphibolite and hornblende-biotite gneiss (TTG). All these rock types are closely associated as an arc magmatic suite, with diffuse boundaries and coeval nature. The charnockite and hornblende-biotite gneisses (TTG) show SiO2 content varying from 64 to 73 wt.%. The hornblende-biotite gneisses (TTG) are high-Al type with Al2O3 >15 wt.% whereas the charnockites show Al2O3 <15 wt.%. The composition of charnockite is mainly magnesian and calcic to calc-alkaline. The mafic-ultramafic rocks show composition close to that of tholeiitic series. The low values of K(2)o (<3 wt.%), (K/Rb)/K2O (<500), Zr/Ti, and trace element ratios like (La/Yb)n/(Sr/Y), (Y/Nb), (Y + Nb)/Rb, (Y+Ta)/Rb, Yb/Ta indicate a volcanic arc signature for these rocks. The geochemical signature is consistent with arc magmatic rocks generated through oceanic plate subduction. The primitive mantle normalized trace element patterns of these rocks display enrichment in large ion lithophile elements (LILE) and comparable high field strength elements (HFSE) in charnockite and hornblende-biotite gneisses (TTG) consistent with subduction-related origin. Primitive mantle normalized REE pattern displays an enrichment in LREE in the chamockite and hornblende-biotite gneisses (TTG) as compared to a flat pattern for the mafic rocks. The chondrite normalized REE patterns of zircons of all the rock types reveal cores with high HREE formed at ca. 2700 Ma and rims with low HREE formed at 2500-2450 Ma. Log-transformed La/Th-Nb/Th-Sm/Th-Yb/Th discrimination diagram for the mafic and ultramafic rocks from Nilgiri displays a transition from mid-oceanic ridge basalt (MORB) to island arc basalt (IAB) suggesting a MORB source. The U-Pb zircon data from the charnockites, mafic granulites and hornblende-biotite gneisses (TTG) presented in our study show that the magma generation during subduction and accretion events in this block occurred at 2700-2500 Ma. Together with the recent report on Neoarchean supra-subduction zone ophiolite suite at its southern margin, the Nilgiri Block provides one of the best examples for continental growth through vertical stacking and lateral accretion in a subduction environment during the Neoarchean. (c) 2014 Elsevier B.V. All rights reserved.

稳态等离子体推进器羽流的粒子模拟

本文利用结合了particle-in-cell方法的直接模拟Monte Carlo方法模拟了稳态等离子体推进器的羽流场.为了更真实地再现实验设备中的流动,模拟中包含了背压气体,并在计算中直接模拟,改变了以往的中性粒子平衡态的处理方式.为了匹配试验结果,修正了推进器出口处气流偏转角分布,并建议最大偏转半角取为20°.计算结果与现有的实验结果符合较好.

The convection during NaClO3 crystal growth observed by the phase shift interferometer

An optical diagnostic system consisting of the Mach-Zehnder interferometer with the phase shift device and an image processor has been developed for the study of the kinetics of the crystal growing process. The dissolution and crystallization process of NaClO3 crystal has been investigated. The concentration distributions around a growing and dissolving crystal have been obtained by using phase-shift of four-steps theory for the interpretation of the interferograms. The convection (a plume flow) has been visualized and analyzed in the process of the crystal growth. The experiment demonstrates that the buoyancy convection dominates the growth rate of the crystal growing face on the ground-based experiment.

Transient natural ventilation of a space with localised heating

The natural ventilation of a well-mixed, pre-heated room with a point source of heating, and openings at the base and roof is investigated. The transient draining associated with the room being warmer than the exterior combined with the convective ow produced by the point source of heat leads to a fascinating series of transient ow regimes as the system evolves to the two-layer steady-state regime described by Linden, Lane-Ser_ and Smeed [1]. As the room begins to ventilate, a turbulent plume rises from the point source of heat to the ceiling, and typically forms a deepening layer of hot air. However, with a weak heat source, then at some point the ascending plume will intrude beneath the layer of original uid. Otherwise, the ascending plume always reaches the top of the room as the system evolves to a steady state. We develop a simpli_ed model of the transient evolution and test this with some new laboratory experiments. We conclude with a discussion of the implications of our results for real buildings.

Transient Ventilation Dynamics Following a Change in Strength of a Point Source of Heat

We investigate the transient ventilation flow within a confined ventilated space, with high- and low-level openings, when the strength of a low-level point source of heat is changed instantaneously. The steady-flow regime in the space involves a turbulent buoyant plume, which rises from the point source to a well-mixed warm upper layer. The steady-state height of the interface between this layer and the lower layer of exterior fluid is independent of the heat flux, but the upper layer becomes progressively warmer with heat flux. New analogue laboratory experiments of the transient adjustment between steady states identify that if the heat flux is increased, the continuing plume propagates to the top of the room forming a new, warmer layer. This layer gradually deepens, and as the turbulent plume entrains fluid from the original warm layer, the original layer is gradually depleted and disappears, and a new steady state is established. In contrast, if the source buoyancy flux is decreased, the continuing plume is cooler than the original plume, so that on reaching the interface it is of intermediate density between the original warm layer and the external fluid. The plume supplies a new intermediate layer, which gradually deepens with the continuing flow. In turn, the original upper layer becomes depleted, both as a result of being vented through the upper opening of the space, but also due to some penetrative entrainment of this layer by the plume, as the plume overshoots the interface before falling back to supply the new intermediate layer. We develop quantitative models which are in good accord with our experimental data, by combining classical plume theory with models of the penetrative entrainment for the case of a decrease in heating. Typically, we find that the effect of penetrative entrainment on the density of the intruding layer is relatively weak, provided the change in source strength is sufficiently large. However, penetrative entrainment measurably increases the rate at which the depth of the draining layer decreases. We conclude with a discussion of the importance of these results for the control of naturally ventilated spaces.