Utilização de resíduos da indústria madeireira para fabricação de chapas cimento-madeira

A industrialização da madeira gera grande quantidade de resíduos, que são lançados no meio ambiente, e não são aproveitados em sua totalidade, ou quando no máximo são utilizados para geração de energia causando também poluição ambiental. Esta pesquisa teve como objetivo avaliar por meio de ensaios físicos, mecânicos e análise da interface fibra-matriz, por microscopia eletrônica de varredura, a utilização dos resíduos da indústria madeireira para moldagem de chapas de cimento-madeira. Foram avaliadas a compatibilidade de seis espécies de dicotiledôneas nativas da Amazônia, e a mistura delas em partes iguais, com ensaios de compressão axial em corpos-de-prova cilíndricos, para escolha daquelas de melhor desempenho para aplicação em chapas. Os resíduos foram utilizados ao natural e submetidos ao tratamento de lavagem em água quente por duas horas, para verificação da influência deste tratamento. O cimento utilizado foi o CP V ARI, com a relação cimento/madeira 3: 1 ,em massa juntamente com os aditivos aceleradores de pega sulfato de alumínio a 3% e cloreto de cálcio a 3% e 5%. Os resultados do ensaio de compressão axial indicaram três espécies com potencial para uso em chapas, com o tratamento lavagem combinado com o acelerador de pega cloreto de cálcio a 5%. A espécie Cedrela odorata L. (Cedro), apresentou o melhor desempenho nos ensaios físicos e mecânicos, superando especificações de fabricantes de chapas, sendo, potencialmente o resíduo mais indicado para utilização em chapas de cimento-madeira.

Avaliação do uso da casca do fruto e das folhas de Caesalpinia ferrea Martius como suplemento nutricional de Fe, Mn e Zn

As plantas medicinais podem ser usadas como fontes alternativas de nutrientes minerais na dieta alimentar. Elementos como ferro, manganês e zinco apresentam biodisponibilidade variável em função de suas formas químicas (espécies) presentes em um alimento. Este trabalho tem como objetivo avaliar o teor e a biodisponibilidade de ferro, manganês e zinco em extratos da casca do fruto e das folhas de Caesalpinia ferrea Martius por Espectrometria de Absorção Atômica com Chama (FAAS). Os agentes extratores testados foram as soluções de NaOH 0,05 mol. L^-1, tampão Tris-HCl 0,05 mol.L^-1 (pH= 8), tampão Tris-HCl 0,05 mol.L^-1 (pH = 8) em dodecil sulfato de sódio (SDS) 1% (m/v), HCl 0,05 mol.L^-1 e água quente (60 ºC). A casca do fruto e as folhas de Caesalpinia ferrea Martius apresentaram níveis altos de ferro e manganês quando comparados aos de outras plantas medicinais. Os elementos estudados mostraram predominante associação com compostos de alta e baixa massa molecular, espécies solúveis e insolúveis em água. Dentre os elementos analisados, o ferro apresentou melhor biodisponibilidade na casca do fruto e nas folhas. Manganês e zinco se mostraram mais biodisponível nas folhas. A casca do fruto e as folhas de Caesalpinia ferrea Martius podem ser uma fonte alternativa de ferro, manganês e zinco na dieta alimentar.

Chapas de cimento-madeira com resíduos da indústria madeireira da Região Amazônica

Este estudo teve como objetivo avaliar o emprego do resíduo da indústria madeireira da região da Amazônia brasileira na produção de material compósito cimento-madeira. Foi avaliada a compatibilidade de seis espécies de dicotiledôneas nativas da Amazônia com o cimento CP V ARI por meio da realização de ensaios de compressão axial em corpos de prova cilíndricos. Os resíduos foram utilizados ao natural e submetidos ao tratamento de lavagem em água quente por 2 h. A relação cimento-madeira foi de 3:1, em massa, juntamente com os aditivos aceleradores de pega sulfato de alumínio a 3% e cloreto de cálcio a 3% e 5%. Os resultados dos ensaios de compressão indicaram como potencial de uso os resíduos de três espécies combinado ao tratamento com o acelerador de pega cloreto de cálcio a 5%. Foram confeccionadas chapas cimento-madeira com resíduos das espécies Cedrela Odorata L. (Cedro), Vochysia máxima Ducke (Quaruba), Hymenaea courbaril L. (Jatobá) e mais a mistura delas. Os resultados dos ensaios das propriedades físicas e mecânicas das chapas mostraram que todas apresentaram características adequadas para a finalidade, e as chapas da espécie cedro apresentaram o melhor desempenho.

Efeito do envelhecimento acelerado sobre a microdureza superficial, rugosidade e opacidade de resinas acrílicas incolores termopolimerizáveis e calotas oculares empregadas em prótese ocular, em função da espessura

Pós-graduação em Odontologia - FOA

Análise da variação da posição dos dentes artificiais durante as fases específicas do processamento de próteses totais superiores mensurada por computação gráfica

Pós-graduação em Odontologia - FOA

Analise exergoeconômica aplicada a microgeração em condomínios residenciais

Pós-graduação em Engenharia Mecânica - FEG

Controle de doenças fúngicas e de danos por frio em pós-colheita de lima ácida Tahiti

The Tahiti lime appears very susceptible to attack by post-harvest diseases, primarily by the fungi Penicillium and Phomopsis, and also because of its high sensitivity to storage at low temperatures. In order to reduce such damage, the present study aimed to verify the efficiency of heat treatment and disinfection of pathogens in the prevention of post-harvest chilling injury of this cultivar and to compare this treatment with other products using the conventional fungicides. The heat treatments were studied with hot-water temperatures ranging between 48 and 56° C. Water at room temperature was used as a control treatment. After treatment, the fruits were kept under cold temperature at 10° C and RH 90% for about 45 days. For comparison, three other treatments were carried out simultaneously, one using imazalil, one with baking soda, and a third with sodium carbonate, these three products being applied by baths in cold water. Two groups of fruit were evaluated, one treated by immersion considering pathogens coming from the field and another by inoculation with spores of the previously isolated pathogens. For the evaluation of physical and chemical parameters of fruits, determinations were made of the skin color, texture, weight loss, size, juice yield, soluble solids, total acidity and vitamin C content. The determination of the sensitivity of the fruit to cold was made by their exposure at temperatures inducing cold damage. The design was a randomized block design with nine treatments, analyzed by the Statgraphics statistical package. Heat treatments, especially at 52° C, were shown to be more promising in the control of pathogenic fungi and cold damage, surpassing the conventional fungicides. No changes were found in the intrinsic and extrinsic parameters in relation to the application of the different treatments.

Effect of Post-silanization Heat Treatments of Silanized Feldspathic Ceramic on Adhesion to Resin Cement

Purpose: To evaluate the effect of post-silanization heat treatment of a silane agent and rinsing with hot water of silanized CAD/CAM feldspathic ceramic surfaces on the microtensile bond strength between resin cement and the ceramic, before and after mechanical cycling.Materials and Methods: Blocks measuring 10 x 5.7 x 3.25 mm(3) were produced from feldspathic ceramic cubes (VITA Mark II, VITA Zanhfabrik). Each ceramic block was duplicated in composite resin using a template made of polyvinylsiloxane impression material. Afterwards, ceramic and corresponding resin composite blocks were ultrasonically cleaned and randomly divided according to the 5 strategies used for conditioning the ceramic surface (n = 10): GHF: etching with hydrofluoric acid 10% + rinsing with water at room temperature + silanization at 20 degrees C; G20: silanization; G77: silanization + oven drying at 77 degrees C; G20r: silanization + hot water rinsing; G77r: silanization + oven drying at 77 C + hot water rinsing. The resin and ceramic blocks were cemented using a dual-curing resin cement. Every group was divided in two subgroups: aging condition (mechanical cycling, designated as a) or non-aging (designated as n). All the bonded assemblies were sectioned into microsticks for microtensile bond strength (mu TBS) testing. The failure mode of the tested specimens was assessed and mu TBS data were statistically analyzed in two ways: first 2-way ANOVA (GHF, G20 and G77 in non-aging/aging conditions) and 3-way ANOVA (temperature x rinsing x aging factors, excluding GHF), followed by Tukey's test (p = 0.05).Results: The 2-way ANOVA revealed that the mu TBS was significantly affected by the surface treatment (p < 0.001) but not by aging (p = 0.68), and Tukey's test showed that G77-n/G77-a (18.0 MPa) > GHF-n/GHF-a (12.2 MPa) > G20-n/G20-a (9.1 MPa). The 3-way ANOVA revealed that the mu TBS was significantly affected by the heat treatment and rinsing factors (p < 0.001), but not affected by aging (p = 0.36). The rinsing procedure decreased, while oven drying increased the bond strengths. Group G77, in both non-aging and aging conditions (18.6-17.4 MPa), had the highest bond values. Failure modes were mainly mixed for all groups.Conclusion: Oven drying at 77 degrees C improved the bond strength between the resin cement and feldspathic ceramic, but hot water rinsing reduced the bond strength and should not be recommended.

Conservação pós-colheita de melões inteiros e minimamente processados

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Análise da relação desempenho/custo de alguns coletores solares comerciais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Cogeneration design problem Computational complexity analysis and solution through an expert system

Purpose - The purpose of this paper is twofold: to analyze the computational complexity of the cogeneration design problem; to present an expert system to solve the proposed problem, comparing such an approach with the traditional searching methods available.Design/methodology/approach - The complexity of the cogeneration problem is analyzed through the transformation of the well-known knapsack problem. Both problems are formulated as decision problems and it is proven that the cogeneration problem is np-complete. Thus, several searching approaches, such as population heuristics and dynamic programming, could be used to solve the problem. Alternatively, a knowledge-based approach is proposed by presenting an expert system and its knowledge representation scheme.Findings - The expert system is executed considering two case-studies. First, a cogeneration plant should meet power, steam, chilled water and hot water demands. The expert system presented two different solutions based on high complexity thermodynamic cycles. In the second case-study the plant should meet just power and steam demands. The system presents three different solutions, and one of them was never considered before by our consultant expert.Originality/value - The expert system approach is not a "blind" method, i.e. it generates solutions based on actual engineering knowledge instead of the searching strategies from traditional methods. It means that the system is able to explain its choices, making available the design rationale for each solution. This is the main advantage of the expert system approach over the traditional search methods. On the other hand, the expert system quite likely does not provide an actual optimal solution. All it can provide is one or more acceptable solutions.

Superação da dormência de sementes de Tucum (Astrocaryum huaimi Mart.)

The objective of this study was to evaluate the effect of immersion for varying periods in different concentrations of gibberellic acid and separate methods of scarification on the germination of seeds tucum. In the first trial, testing different soaking periods (24 and 48 hours), different forms of soaking (fast and slow) and different concentrations of gibberellic acid (0, 100 and 200 mg L-(1)) compared to the control (water) under completely randomized design in a factorial 2x2x3. The second experiment evaluated the different scarification treatments being: physical (seed coat removal in the hilar region with the aid of a scalpel), chemical (sulfuric acid 98 PA for 2:04 minutes) and thermal (hot water at approximately 98 degrees C and cold water at about 2 degrees C for 4 minutes). In the first trial were evaluated % of contaminated seeds (seeds infected by microorganisms) and hard seeds (who did not start the germination process, but not soiled), and in the second we assessed germination percentage (%) every two days for three months; germination Speed Index (GSI), time to occurrence of 50 % germination (T50) and Emergency Speed Index (ESI). The use of gibberellic acid was ineffective in promoting germination of Tucum (Astrocaryum Huaimi Mart.). Scarification treatments were effective in promoting germination and emergence of seedlings in the nursery and the most efficient physical removal scarification of the seed coat in the hilar region with the highest percentage of germination.

Analise técnico-econômica de um gaseificador Downdraft e de filtros para limpeza de gás de síntese

The biomass gasification systems have been used for a long time and prove to be a good alternative to the generation of energy problems. This type of management requires a simple installation and maintenance which gives them a high availability. In Biomass project via Call CTEnerg 33/2006-1, funded by the Ministry of Science and Technology - MCT - Brazil, the Group Energy Systems Optimization – GOSE - at FEG - UNESP built and tested two prototypes of gasifiers. These is fed with 25 kg / h of dry wood (chips), and 50 Nm3 / h of air to produce gas at a flow rate of approximately 70 Nm3 / h of wood (syngas) at a temperature approximately 600 ° C. In this work of graduation, studies were conducted on the materials used in both the gasifier as well as cleaning the filter synthesis gases. The system of gas cleaning and conditioning is vital to ensure the life of the Internal Combustion Engine. In this case the studies of different filters for small gasification systems (properties, materials used, characteristics, types, etc.) are very relevant to its use in the prototype of the college campus. Were also performed a technical and economic analysis of a cogeneration system that consists in the combination of the downdraft gasifier studied in this work, an internal combustion engine, two heat exchangers and a SRA (absorption system refrigerator). Were calculated the costs of electricity generation, hot water and cold water. Finally, we analyzed the economic feasibility of the project

Avaliação da viabilidade econômica do uso de um aquecedor solar de água de garrafas pet para aquecer o ar de uma cabine de pintura e uma estufa de secagem

Nowadays, the biggest part of the world's energy supply comes from fossil fuels and nuclear. However, the current need of the society for the preservation of the environment and wise use of natural resources, has favored the search for alternative energy sources and improvement of energy efficiency. In this new scenario, companies are beginning to mobilize in order to adapt its facilities to renewable energy. Solar, with its immense potential, not really exploited yet, can be very useful for companies that want to beat their sustainability goals. Given these facts, the aim is to evaluate the economic viability of introducing a solar water heater which uses a colorless PET bottle as one of its components in a plant. The hot water generated will heat the air of a paint booth and a warm house, reducing energy consumption, since they are heated by electric heaters

Fibras naturais: características químicas e potenciais aplicações

This study has as objective determining the chemical properties that serve as the basis for potential scientific and technological applications of seven species of fibrous plants cultivated in Brazil, which are: Banana” (Musa spp.), “Coco” (Cocos nucifera), Curauá (Ananas erectifolius), Fique (Furcraea andina), Piteira” (Furcraea gigantea), Sisal(Agave sisalana) and “Taboa” (Typha domingensis). The tests for determining the percent dry completely, extractives soluble in cold water, in hot water, in sodium hydroxide 1% and in ethanol-toluene, and the percentages of ash, hydrophobicity, lignin, holocellulose and cellulose were performed at the Department of Environmental Sciences, Agronomy College (FCA) of UNESP – Botucatu, São Paulo State. It also presents a literature review about these fibers and their potential applications. Differences between the results obtained and those found by other authors are possibly explained by variations on the origin of plant material, the harvest season, the climate and soil where they were grown. However, the results and the methodology used, serve as a basis for further studies with natural fibers