Flow of metal in constrained plane-strain extrusion forging- Part II

With many innovations in process technology, forging is establishing itself as a precision manufacturing process: as forging is used to produce complex shapes in difficult materials, it requires dies of complex configuration of high strength and of wear-resistant materials. Extensive research and development work is being undertaken, internationally, to analyse the stresses in forging dies and the flow of material in forged components. Identification of the location, size and shape of dead-metal zones is required for component design. Further, knowledge of the strain distribution in the flowing metal indicates the degree to which the component is being work hardened. Such information is helpful in the selection of process parameters such as dimensional allowances and interface lubrication, as well as in the determination of post-forging operations such as heat treatment and machining. In the presently reported work the effect of aperture width and initial specimen height on the strain distribution in the plane-strain extrusion forging of machined lead billets is observed: the distortion of grids inscribed on the face of the specimen gives the strain distribution. The stress-equilibrium approach is used to optimise a model of flow in extrusion forging, which model is found to be effective in estimating the size of the dead-metal zone. The work carried out so far indicates that the methodology of using the stress-equilibrium approach to develop models of flow in closed-die forging can be a useful tool in component, process and die design.

Optimising indoor phosphine fumigation of paddy rice bag-stacks under sheeting for control of resistant insects

Three indoor, sheeted bag-stack fumigations of paddy rice using aluminium phosphide were undertaken in Guangdong Province, southern China. We measured the effect of two types of sheeting (polyvinylchloride [PVC] or polyethylene [PE]) and two types of floor sealing (clips or fixing into a slot with a rubber pipe) on phosphine concentration and retention. The aim was to test the feasibility of retaining fumigant at a sufficient concentration for long enough to control known resistant insect pests. Each stack was pressure tested and phosphine concentrations measured daily during the fumigation. Cages of test insects in culture medium, including resistant and susceptible strains, were placed inside each stack and could be observed through the clear sheeting. Highest concentrations for the longest period were obtained in a PVC-covered stack that included a ground sheet and wall sheets sealed to the floor with rubber pipes. A similar PVC-covered stack sealed to the floor with clips instead of pipe did not retain gas as efficiently and required re-dosing. A PE-covered stack, with no ground sheet but also with wall sheets sealed to the floor with pipe, produced an acceptable fumigation. Susceptible Rhyzopertha dominica were controlled in 2 days and the most resistant strain in 15 days. Resistant Cryptolestes ferrugineus survived until day 21. The paddy was still free of insect infestation 7 months later when the bag-stack was opened to mill the rice. Pressure half-lives correlated with gas concentration and retention. Sorption appeared to be a major limiting factor, reducing potential fumigant dosage by about 50%. The trials demonstrated the feasibility of sealing bag-stacks to a standard high enough to control all known resistant strains.

Influence of concentration, temperature and humidity on the toxicity of phosphine to the strongly phosphine-resistant psocid Liposcelis bostrychophila Badonnel (Psocoptera: Liposcelididae)

BACKGROUND: The psocid Liposcelis bostrychophila Badonnel, is a widespread, significant pest of stored commodities, has developed strong resistance to phosphine, the major grain disinfestant. The aim was to develop effective fumigation protocols to control this resistant pest. RESULTS: Time to population extinction of all life stages (TPE) in days was evaluated at a series of phosphine concentrations and temperatures at two relative humidities. Regression analysis showed that temperature, concentration and relative humidity all contributed significantly to describing TPE (P < 0.001, R2 = 0.95), with temperature being the dominant variable, accounting for 74.4% of the variation. Irrespective of phosphine concentration, TPE was longer at lower temperatures and high humidity (70% RH) and shorter at higher temperatures and low humidity (55% RH). At any concentration of phosphine, a combination of higher temperature and lower humidity provides the shortest fumigation period to control resistant L. bostrychophila. For example, 19 and 11 days of fumigation are required at 15 °C and 70% RH at 0.1 and 1.0 mg L-1 of phosphine respectively, whereas only 4 and 2 days are required at 35 °C and 55% RH for the same respective concentrations. CONCLUSIONS: The developed fumigation protocols will provide industry with flexibility in application of phosphine.

Effect of micro-propagation on the health status of strawberry planting material for commercial production of strawberry runners for Queensland

Plant tissue culture has been used for a number of years to produce micropropagated strawberry plants for planting into runner growing beds in the Stanthorpe (Queensland) and Bothwell (Tasmania) regions. This process has allowed the rapid release of new cultivars from the LAWS (Late Autumn, Winter, Spring) breeding program into the current runner production system. Micro-propagation in vitro allows plants to be produced during the autumn and winter months, when mother plants would normally be in a fruit production phase in the field in Queensland. The plants produced are of a high health status when they are planted. The subsequent arrival and build up of various diseases in the runner fields are closely monitored. Using tissue culture for the first generation reduces the time the plants spend in the field by twelve months, reducing disease incidence. To date, any disease outbreak has been successfully managed using early detection and rapid response methods.

SSR analysis of cultivated groundnut (Arachis hypogaea L.) germplasm resistant to rust and late leaf spot diseases

Cultivated groundnut (Arachis hypogaea L.) is an agronomically and economically important oilseed crop grown extensively throughout the semi-arid tropics of Asia, Africa and Latin America. Rust (Puccinia arachidis) and late leaf spot (LLS, Phaseoisariopsis personata) are among the major diseases causing significant yield loss in groundnut. The development of varieties with high levels of resistance has been constrained by adaptation of disease isolates to resistance sources and incomplete resistance in resistant sources. Despite the wide range of morphological diversity observed in the cultivated groundnut gene pool, molecular marker analyses have thus far been unable to detect a parallel level of genetic diversity. However, the recent development of simple sequence repeat (SSR) markers presents new opportunities for molecular diversity analysis of cultivate groundnut. The current study was conducted to identify diverse disease resistant germplasm for the development of mapping populations and for their introduction into breeding programs. Twenty-three SSRs were screened across 22 groundnut genotypes with differing levels of resistance to rust and LLS. Overall, 135 alleles across 23 loci were observed in the 22 genotypes screened. Twelve of the 23 SSRs (52%) showed a high level of polymorphism, with PIC values ≥0.5. This is the first report detecting such high levels of genetic polymorphism in cultivated groundnut. Multi-dimensional scaling and cluster analyses revealed three well-separated groups of genotypes. Locus by locus AMOVA and Kruskal-Wallis one-way ANOVA identified candidate SSR loci that may be valuable for mapping rust and LLS resistance. The molecular diversity analysis presented here provides valuable information for groundnut breeders designing strategies for incorporating and pyramiding rust and late leaf spot resistances and for molecular biologists wishing to create recombinant inbred line populations to map these traits.

Simple sequence repeat markers associated with three quantitative trait loci for black point resistance can be used to enrich selection populations in bread wheat

Black point in wheat has the potential to cost the Australian industry $A30.4 million a year. It is difficult and expensive to screen for resistance, so the aim of this study was to validate 3 previously identified quantitative trait loci (QTLs) for black point resistance on chromosomes 2B, 4A, and 3D of the wheat variety Sunco. Black point resistance data and simple sequence repeat (SSR) markers, linked to the resistance QTLs and suited to high-throughput assay, were analysed in the doubled haploid population, Batavia (susceptible) × Pelsart (resistant). Sunco and Pelsart both have Cook in their pedigree and both have the Triticum timopheevii translocation on 2B. SSR markers identified for the 3 genetic regions were gwm319 (2B, T. timopheevii translocation), wmc048 (4AS), and gwm341 (3DS). Gwm319 and wmc048 were associated with black point resistance in the validation population. Gwm341 may have an epistatic influence on the trait because when resistance alleles were present at both gwm319 and wmc048, the Batavia-derived allele at gwm341 was associated with a higher proportion of resistant lines. Data are presented showing the level of enrichment achieved for black point resistance, using 1, 2, or 3 of these molecular markers, and the number of associated discarded resistant lines. The level of population enrichment was found to be 1.83-fold with 6 of 17 resistant lines discarded when gwm319 and wmc048 were both used for selection. Interactions among the 3 QTLs appear complex and other genetic and epigenetic factors influence susceptibility to black point. Polymorphism was assessed for these markers within potential breeding material. This indicated that alternative markers to wmc048 may be required for some parental combinations. Based on these results, marker-assisted selection for the major black point resistance QTLs can increase the rate of genetic gain by improving the selection efficiency and may facilitate stacking of black point resistances from different sources.

Micropropagation of vegetatively propagated crops: accelerating release of new cultivars and providing an important source of clean planting material

Micropropagation is unequalled for the rapid clonal propagation of improved cultivars from several Australian breeding programmes. This has been particularly true of the pineapple breeding programme, but it has also found an important role in the strawberry breeding programme where high-health mother stock is of paramount concern. In the banana and ginger industries, while access to new cultivars has been of importance, micropropagation has been adopted by the industry to ensure that planting materials are free from serious pests and diseases. Bananas can be used as planting material as early as the first generation ex vitro and is responsible for the establishment of laboratories and nurseries specializing in the production of pathogen-tested plants. The ginger industry, on the other hand, has used micropropagated plants as a source of disease and pest-free stock to establish a clean 'seed' scheme based on the production of conventional planting material.

Estimation of Cavitation Erosion with Incubation Periods and Material Properties

A detailed study of the normalized correlations between the incubation period tc and the properties of various materials tested in a rotating disk device indicates that, at very high intensities, the strength properties influence the duration of tc. The analysis of extensive data from other laboratories for cavitation and liquid impingement erosion also indicates that, while both energy and strength properties influence the duration of tc, the latter ones predominate for a majority of cases. A fatigue-type failure occurs during tc. For estimating the time required to pierce a metallic specimen in a rotating device a relationship tp = 160 tc0.44 is proposed. A detailed study of normalized correlations between erosion resistance (inverse of erosion rate) and tc values of different materials tested in the rotating disk shows that correlations are good. Analysis of data from eight other investigators clearly points out the validity and the usefulness of this type of prediction.

Elizabeth Krakauer nee Gottschalk seated in a Oberprima (high school) chemistry laboratory; Sophienschule; Hannover, Germany.

This picture was taken during her last year of high school. The chemistry teacher, Professor Schmigielski was one of Elizabeth's favorite teachers.

The use of temperate species in the Australian subtropics.

Temperate species and tropical crop silage are the basis for forage production for the dairy industry in the Australian subtropics. Irrigation is the key resource needed for production, with little survival of temperate species under rain-grown conditions except for lucerne. Annual ryegrass (Lolium multiflorum), fertilised with either inorganic nitrogen or grown with clovers, is the main cool season forage for the dairy industry. It is sown into fully prepared seedbeds, oversown into tropical grasses, especially kikuyu (Pennisetum clandestinum) or sown after mulching. There has been a continual improvement in the performance of annual and hybrid ryegrass cultivars over the last 25 years. In small plot, cutting experiments, yields of annual ryegrass typically range from 15 to 21 t DM/ha, with equivalent on-farm yields of 7 to 14 t DM/ha of utilised material. Rust (Puccinia coronata) remains the major concern although resistance is more stable than in oats. There have also been major improvements in the performance of perennial ryegrass (L. perenne) cultivars although their persistence under grazing is insufficient to make them a reliable forage source for the subtropics. On the other hand, tall fescue (Festuca arundinacea) and prairie grass (Bromus willdenowii) cultivars perform well under cutting and grazing, although farmer resistance to the use of tall fescue is strong. White clover (Trifolium repens) is a reliable and persistent performer although disease usually reduces its performance in the third year after sowing. Persian (Shaftal) annual clover (T. resupinatum) gives good winter production but the performance of berseem clover (T. alexandrinum) is less reliable and the sub clovers (T. subterraneum) are generally not suited to clay soils of neutral to alkaline pH. Lucerne (Medicago sativa), either as a pure stand or in mixtures, is a high producing legume under both irrigation and natural rainfall. Understanding the importance of leaf and crown diseases, and the development of resistant cultivars, have been the reasons for its reliability. Insects on temperate species are not as serious a problem in the subtropics as in New Zealand (NZ). Fungal and viral diseases, on the other hand, cause many problems and forage performance would benefit from more research into resistance.

Elizabeth Krakauer nee Gottschalk conducting an experiment in a Oberprima (high school) chemistry laboratory; Sophienschule; Hannover, Germany.

This picture was taken during her last year of high school. The chemistry teacher, Professor Schmigielski was one of Elizabeth's favorite teachers.

Elizabeth Krakauer nee Gottschalk seated in a Oberprima (high school) chemistry laboratory; Sophienschule; Hannover, Germany.

This picture was taken during her last year of high school. The chemistry teacher, Professor Schmigielski was one of Elizabeth's favorite teachers.

Behavior Of High-Voltage Machine Insulation System In The Presence Of Thermal And Electrical Stresses

This paper presents the results on a resin-rich machine insulation system subjected to varying stresses such as electrical (2.6 to 13.3 MV/m) and thermal (40 to 155° C) acting together. Accelerated electro-thermal aging experiments subsequently have been performed to understand the insulation degradation The interpretations are based on several measured properties like capacitance, loss tangent, ac resistance, leakage current, and partial discharge quantities. The results indicate that the changes in properties are not significant below a certain temperature for any applied stress, Beyond this temperature large variations are observed even for low electrical stresses. Electrothermal aging studies reveal that the acceleration of the insulation degradation and the ultimate time to failure depends on the relative values of temperature and voltage stresses. At lower temperatures, below critical, material characteristics of the system predominate whereas beyond this temperature, other phenomena come into play causing insulation deterioration. During aging under combined stresses, it appears that the prevailing temperature of the system has a significant role in the insulation degradation and ultimate failure.

Study of effects of dopants on structure of vitreous semiconductors (GeSe3.5)100-xMx (M = Bi, Sb) using high pressure techniques

An investigation of the problem of controlled doping of amorphous chalcogenide semiconductors utilizing a Bridgman anvil high pressure technique, has been undertaken. Bulk amorphous semiconducting materials (GeSe3.5)100-x doped with M = Bi (x = 2, 4, 10) and M = Sb (x = 10) respectively are studied up to a pressure of 100 kbar down to liquid nitrogen temperature, with a view to observe the impurity induced modifications. Measurement of the electrical conductivity of the doped samples under quasi-hydrostatic pressure reveals that the pressure induced effects in lightly doped (2 at % Bi) and heavily doped (x = 4, 10) semiconductors are markedly different. The pressure effects in Sb-doped semiconductors are quite different from those in Bi-doped material.

Elizabeth Krakauer nee Gottschalk seated in a Oberprima (high school) chemistry laboratory; Sophienschule; Hannover, Germany.

This picture was taken during her last year of high school. The chemistry teacher, Professor Schmigielski was one of Elizabeth's favorite teachers.