Ion transport in polymer electrolytes containing nanoparticulate TiO2 : The influence of polymer morphology

Recent studies have shown that composite polymer electrolytes, formed by dispersing nanosized ceramic particles in polyether-based electrolytes, have improved ion transport properties as compared to their unfilled analogues. In the present study polymer electrolytes with different loadings of nano-sized ceramic particles (TiO₂) and different polymer chemistry and morphology have been investigated. Of special interest are filler induced effects on polymer, solvent and cationic mobility. Partly crystalline polymer electrolytes based on poly(ethylene oxide) have been compared to fully amorphous polymer electrolytes based on a polyether urethane, as well as gel electrolytes based on PMMA. ⁷Li pfg-NMR, linewidth and spin–spin relaxation times as well as ¹H pfg-NMR and spin–spin relaxation times, were measured as a function of temperature and composition. The ¹H spin–spin relaxation measurements reveal increased average polymer mobility with the addition of filler up to a maximum at 4 and 8 wt.% TiO₂ for the fully amorphous and the partly crystalline electrolytes, respectively. The ⁷Li linewidth measurements for the fully amorphous system show a broadening of the linewidth with addition of filler. Based on variable temperature measurements this broadening is interpreted as a result of the inhomogeneity introduced by the filler particles. Pulsed field gradient (pfg) diffusion measurements were employed to determine ion and solvent self-diffusion coefficients. In the case of the PMMA-based gel electrolyte and the fully amorphous electrolytes enhanced cation self-diffusion was observed upon addition of TiO₂.

7Li NMR measurements of polymer gel electrolytes

Ion conducting polymer gels prepared from (ethylene oxide)_n grafted methacrylates, ethylene carbonate (EC), gamma butyrolactone (gBL), and lithium hexafluorophosphate are studied by means of nuclear magnetic resonance spectroscopy. This study shows that there are at least two possible lithium sites with different mobility. The lithium-ions with lower mobility dominate at room temperature, but this is changed as the temperature is increased. The NMR results also show that the ⁷Li spin–spin relaxation time decreases with increasing length of the grafted ethylene oxide side chains, indicating a stronger interaction between the polymer and the Li-ions, and hence, a lower mobility of the Li-ions.

A 7Li and 19F NMR relaxation study of LiCF3SO3 in plasticised solid polyether electrolytes

⁷Li and ¹⁹F NMR relaxation time (T₁, T₂, T_1ρ) measurements have been used to probe the dynamics of LiCF₃SO₃ dissolved in an amorphous co-polymer poly(ethylene oxide-co-propylene oxide), and in particular the influence of the plasticising agents propylene carbonate and dimethyl formamide. The changes in relaxation behaviour of ¹⁹F and ⁷Li with increasing plasticiser concentration are very different, as is the effect of each plasticiser. These differences can be explained qualitatively in terms of the interaction between the plasticiser and the ions. Preliminary ⁷Li T_1ρ measurements reveal two components at low temperatures.

Microscopic interactions in nanocomposite electrolytes

Nanocomposite electrolytes of a fully amorphous trifunctional polyether (3PEG) and poly- (methylene ethylene oxide) (PMEO) have been complexed with two lithium salts and nanoparticulate (~20 nm) fillers of TiO2 and Al2O3. Addition of the fillers to the polymer salt complexes shows a significant change in the conformational modes of both polymers, especially the D-LAM region between 200 and 400 cm-1, indicating a reduced segmental flexibility of the chain. These changes are more pronounced with the use of TiO2 than Al2O3. Incorporation of the nanoparticulate fillers to the electrolytes fails to influence the degree of ion association, suggesting that the number of charge carriers available for conduction in both polymers using both LiClO4 and LiCF3SO3 is not the source of any conductivity increase. Addition of the fillers, which was seen to increase the conductivity in PEO-based systems, generally lowers the conductivity in the present PMEO systems, while the addition of TiO2 has little or no effect except in the cases of 3PEG 1.5 and 1.25 mol/kg LiClO4. In this case, 10 wt % TiO2 provides a conductivity increase of half an order of magnitude at approximately 60 °C. We also report for the first time a Raman spectroscopy investigation into the PEO-based nanocomposite electrolytes. The present results are discussed in terms of the electrostatic interactions involving dielectric properties of the fillers, of special interest being the interactions between the polymer and the fillers and between the ionic species and the fillers, when the effect of crystallization can be ignored.

FT-IR investigation of Ion association in plasticized solid polymer electrolytes

FT-IR spectroscopy has been utilized to monitor ion association in plasticized solid polymer electrolytes (SPEs). The SPEs were prepared from a random copolymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethanesulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethyl ether (tetraglyme) and N,N‘-dimethylformamide (DMF) were chosen as model plasticizers. Despite having a similar dielectric constant to that of the polymer host, ε ~ 5, the incorporation of tetraglyme into the SPEs resulted in increased ion association. The addition of a higher dielectric constant solvent , DMF, ε = 36.7, resulted in decreased ion association in the SPE. The effects of salt concentration (0.05−1.25 mol dm^-3) and temperature (25−100 °C) upon ion association in SPEs were also investigated. At low salt concentrations, ion association was found to increase with temperature, however, at 1.25 mol dm^-3 the temperature dependence of ion association was dominated by concentration effects. There appears to be a maximum in the fraction of “free” ions at a LiCF₃SO₃ concentration of 0.4 mol dm^-3, preceded by a minimum at approximately 0.2 mol dm^-3, consistent with the molar conductivity behavior previously observed in these electrolytes.

Triflate ion association in plasticized polymer electrolytes

Ion association in plasticised solid polymer electrolytes (SPEs) has been monitored using FT-IR spectroscopy. The SPEs were prepared from a random co-polymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethane sulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethylether (tetraglyme, ε˜5) and N,N'-dimethyl formamide (DMF, ε = 36.7) were chosen as model plasticisers. Decreased ion association resulted from plasticization with DMF, indicating that the addition of a higher dielectric constant solvent increases the fraction of dissociated ions in the SPE. The incorporation of tetraglyme into these SPEs results in increased ion association, despite the similar dielectric constants of the plasticiser and polymer host. The effects of salt concentration (0.05–1.25 mol dm^{− 3} solvent) upon ion association in SPEs was also investigated. There appears to be a minimum in the number of “free” ions at a LiTf concentration of 0.2 mol dm^{− 3} solvent followed by a maximum at approximately 0.4 mol dm^{− 3} solvent, consistent with the molar conductivity behaviour previously observed in these electrolytes.

Ionic conductivity studies of polymeric electrolytes containing lithium salt with plasticizer

New plasticized polymer electrolytes were synthesized based on poly ethylene oxide (PEO), Poly (N,N-dimethylamino-ethyl-methacrylate) (PDMAEMA), LiN(CF₃SO₂)₂ (LITFSI) as the salt and tetraethylene glycol dimethyl ether(tetraglyme) and EC + PC as plasticizers. The preparation and characterization of the polymer electrolytes were investigated as a function of temperature and various concentrations of LITFSI. Impedance spectroscopy and differential scanning calorimeter (DSC) were used to characterize the effects of various temperature, lithium salt concentration and two plasticizers on conductivity. The complex of PDMAEMA/PEO/LiTFSI/tetraglyme (S2) exhibits higher conductivity (4.74 × 10⁻⁴ S cm⁻¹at 25 °C) than PDMAEMA/PEO/LiTFSI/EC + PC (S1).

Conductivity and NMR properties of plasticized polyethers complexed with lithium salts

NMR provides a tool whereby the dynamic properties of specific nuclei can be investigated. In the present study, a poly(ethylene oxide-co-propylene oxide) network has been used as the polymer host to prepare solid polymer electrolytes (SPE) containing either LiClO₄ or LiCF₃SO₃. In addition, a low molecular weight plasticizer [propylene carbonate (PC), dimethyl formamide (DMF) or tetraglyme] has been added to several of the samples to enhance the mobility of the polymer and, thus, of the ionic species. The effects of plasticizer and salt concentration on the ionic structure and mobility in these SPEs, as measured by NMR relaxation times, and correlation to the conductivity behaviour in these systems are discussed. Temperature dependent triflate diffusion coefficients, as measured by Pulsed Field Gradient ¹⁹F-NMR, in plasticized SPEs are also reported.

Ftir study of ion-pairing effects in plasticized polymer electrolytes

The effect of plasticizer on the ubiquitous ion-pairing observed in polymer electrolytes has been investigated using FTIR as a probe of the local environment of the triflate ion in sodium and lithium triflate based electrolytes. Plasticizers having a range of properties, such as, propylene carbonate, and dimethyl formamide (DMF), have been investigated in the pure state for comparison with the polymer (a random copolymer of ethylene oxide at propylene oxide (mol ratio 3: 1)). The different plasticizers exhibited strikingly different effects on the triflate ion bands normally observed in polyether salt systems. In particular, the cation associated triflate ion bands at 1288 and 1248 cm⁻¹ and the band at 1272 cm⁻¹ which has variously been assigned to the free ion and also to the strongly aggregated anion, are different. PC produces a rapid disappearance of the “free” ion band in favour of the monodentate ion pair. On the other hand, DMF strongly enhances the band near 1270 cm⁻¹ at salt concentrations higher than 0.7 mol kg⁻¹. These observations are discussed in terms of recent ab initio calculations of the triflate vibrational bands.

Mechanical properties of polyether-plasticiser-salt systems as polymer electrolytes

The mechanical properties of urethane crosslinked poly(ethylene oxide-co-propylene oxide) glyceryl ether-plasticiser (tetraethylene glycol dimethyl ether, or methylformamide)-salt (LiClO₄)-based polymer electrolytes have been studied. It was found that, with increasing concentration of salt, the elastic modulus and tensile strength of the materials unexpectedly decrease. This is interpreted in terms of a predominance of intramolecular coordination of the Li⁺ ions by the polymer.

Microphase separation through competitive hydrogen bonding in double crystalline diblock copolymer/homopolymer blends

Microphase separation induced by competitive hydrogen bonding interactions in double crystalline diblock copolymer/homopolymer blends was studied for the first time. Poly(ethylene oxide)- block-poly(e-caprolactone) (PEO-b-PCL)/poly(4-vinylphenol) (PVPh) blends were prepared in tetrahydrofuran. The diblock copolymer PEO-b-PCL consists of two immiscible crystallizable blocks wherein bothPEO and PCL blocks can form hydrogen bonds with PVPh. In these A-b-B/C diblock copolymer homopolymer blends, microphase separation takes place due to the disparity in intermolecular interactions; specifically, PVPh and PEO block interact strongly whereas PVPh and PCL block interact weakly. The TEM and SAXS results show that the cubic PEO-b-PCL diblock copolymer changes into ordered hexagonal cylindrical morphology upon addition of 20 wt % PVPh followed by disordered bicontinuous phase in the blend with 40 wt % PVPh and then to homogeneous phase at 60 wt % PVPh and above blends. Up to 40 wt % PVPh there is only weak interaction between PVPh and PCL due to the selective hydrogen bonding between PVPh and PEO. However, with higher PVPh concentration, the blends become homogeneous since a sufficient amount of PVPh is available to form hydrogen bonds with both PEO and PCL. A structural model was proposed to explain the self-assembly and microphase morphology of these blends based on the experimental results obtained. The formation of nanostructures and changes in morphologies depend on the relative strength of hydrogen bonding interaction between each block of the block copolymer and the homopolymer.

Cloud-point extraction of phenanthrene by nonionic surfactants

Extraction and preconcentration of the model polycyclic aromatic hydrocarbon (PAH), phenanthrene, in aqueous solutions by two different kinds of nonionic ethoxylated alcohols, Tergitol 15-S-7 and Neodol 25-7, as extractants was studied at ambient temperature (22°C). Both surfactants have almost the same numbers of hydrocarbons and ethylene-oxide (EO) units, but differ in the location of the alcohols. Neodol 25-7 is a primary alcohol, while Tergitol 15-S-7 is a secondary one. The extraction process is based on the clouding phenomena of these two nonionic surfactants. Addition of sodium sulfate or sodium phosphate could decrease the cloud point temperatures of the surfactant solutions below the ambient temperatures, so that the cloud-point extraction process could be facilitated. Increasing the salt concentration or decreasing the surfactant concentration could improve the preconcentration factor, which is attributable to the decrease in the volume of surfactant-rich phase. Consequently, the recovery efficiency higher than 96% was achieved for phenanthrene in aqueous solution.

Effects of additives on the cloud points of selected nonionic linear ethoxylated alcohol surfactants

Effects of various additives including inorganic salts, nonionic and ionic surfactants, water-soluble polymers and alcohols on the cloud points of three linear nonionic surfactants, Tergitol 15-S-7, Tergitol 15-S-9 and Neodol 25-7, were investigated. These surfactants are readily biodegradable and either linear primary or secondary ethoxylated alcohols. Cloud points of these surfactants were functions of their concentrations and concentrations of additives. The cloud points of nonionic surfactant mixtures lay in between the cloud points of individual component surfactants. Presence of two ionic surfactants, sodium dodecyl sulfate (SDS) and cetyl trimethyl ammonium bromide (CTAB), increased the cloud point of 1 wt% Tergitol 15-S-7 micellar solution dramatically when concentrations of ionic surfactants approaching their critical micelle concentration. Addition of water-soluble polymers decreased the cloud point, while addition of inorganic salts can either increase or decrease the cloud points. However, the effect of an alcohol additive on cloud point was dependent on its chain length or its water solubility. Interestingly, synergistic effects between sulfate or phosphate and pentanol on depression of cloud points of Tergitol 15-S-9 were discovered. A linear model predicting cloud points of Tergitol 15-S-X (X = 7, 9 and 12) surfactants and Neodol 25-X (X = 7, 9 and 12) surfactants were proposed with a correlation to logarithm of their ethylene oxide numbers.

Multiple vesicular morphologies in AB/AC diblock copolymer complexes through hydrogen bonding interactions

We report for the first time multiple vesicular morphologies in block copolymer complexes formed in aqueous media via hydrogen bonding interactions. A model AB/AC diblock copolymer system consisting of polystyrene-block- poly(acrylic acid) (PS-b-PAA) and polystyrene-block-poly(ethylene oxide) (PS-b-PEO) was examined using transmission electron microscopy, small-angle X-ray scattering, and dynamic light scattering. The complexation and morphological transitions were driven by the hydrogen bonding between the complementary binding sites on PAA and PEO blocks of the two diblock copolymers. Upon the addition of PS-b-PEO, a variety of bilayer aggregates were formed in PS-b-PAA/PS-b-PEO complexes including vesicles, multilamellar vesicles (MLVs), thick-walled vesicles (TWVs), interconnected compound vesicles (ICCVs), and irregular aggregates. Among these aggregates, ICCVs were observed as a new morphology. The morphology of aggregates was correlated with respect to the molar ratio of PEO to PAA. At [EO]/[AA] = 0.5, vesicles were observed, while MLVs were obtained at [EO]/[AA] = 1. TWVs and ICCVs were formed at [EO]/[AA] = 2 and 6, respectively. When [EO]/[AA] reached 8 and above, only irregular aggregates appeared. These findings suggest that complexation between two amphiphilic diblock copolymers is a viable approach to prepare polymer vesicles in aqueous media.

Hydrogen bonding induced vesicular morphologies in diblock copolymer complexes

It is well-known that the self-assembly of block copolymers either in water or in organic solvents can form a wide range of morphologies in nanometer dimensions depending on its chemical nature. In the present study, the complexation and aggregate morphologies in a model AB/AC diblock copolymer system consisting of polystyrene-block-poly(acrylic acid) (PS-b-PAA) and polystyrene-block-poly(ethylene oxide) (PS-b-PEO) in water were studied using transmission electron microscopy (TEM), small angle X-ray scattering (SAXS), and dynamic light scattering (DLS). By varying the relative amounts of the two block copolymers, a variety of bilayer aggregates were formed, including vesicles, multilamellar vesicles (MLVs), thick-walled vesicles (TWVs), interconnected compound vesicles (ICCVs), and irregular aggregates. The hydrophobic PS blocks were segregated as the cores while the hydrogen bonded PEO and PAA blocks formed the coronae of bilayer aggregates. We also investigate how the addition of PS-b-PEO into PS-b-PAA solutions influences the aggregate morphology of the resulting complexes. This work introduces a viable route to multicompartment vesicles in aqueous solutions. The formation of block copolymer vesicles in water is of particular interest because of their potential in various applications.