A unified circuit model for the polysilicon thin film transistor

This paper describes a unified approach to modelling the polysilicon thin film transistor (TFT) for the purposes of circuit design. The approach uses accurate methods of predicting the channel conductance and then fitting the resulting data with a polynomial. Two methods are proposed to find the channel conductance: a device model and measurement. The approach is suitable because the TFT does not have a well defined threshold voltage. The polynomial conductance is then integrated generally to find the drain current and channel charge, necessary for a complete circuit model. © 1991 The Japan Society of Applied Physics.

Influence of lattice temperature on SOI MOSFET's output characteristics

An explanation for the observed variations in the output behaviour of SOI transistors with different buried oxide thicknesses is presented. At low drain bias, the temperature effects are relatively insignificant while at high drain bias, the temperature effects dominate the nonlinear behaviour of the output characteristics.

Short-channel polymer field-effect-transistor fabrication using spin-coating-induced edge template and ink-jet printing

A method to fabricate polymer field-effect transistors with submicron channel lengths is described. A thin polymer film is spin coated on a prepatterned resist with a low resolution to create a thickness contrast in the overcoated polymer layer. After plasma and solvent etching, a submicron-sized line structure, which templates the contour of the prepattern, is obtained. A further lift-off process is applied to define source-drain electrodes of transistors. With a combination of ink-jet printing, transistors with channel length down to 400 nm have been fabricated by this method. We show that drive current density increases as expected, while the on/off current ratio 106 is achieved. © 2005 American Institute of Physics.

Ecological imbalances in the coastal areas of Pakistan and Karachi Harbour

The marine environment of Pakistan has been described in the context of three main regions : the Indus delta and its creek system, the Karachi coastal region, and the Balochistan coast. The creeks, contrary to concerns, do receive adequate discharges of freshwater. On site observations indicate that freshwater continues flowing into them during the lean water periods and dilutes the seawater there. A major factor for the loss of mangrove forests as well as ecological disturbances in the Indus delta is loss of the silt load resulting in erosion of its mudflats. The ecological disturbance has been aggravated by allowing camels to browse the mangroves. The tree branches and trunks, having been denuded of leaves are felled for firewood. Evidence is presented to show that while indiscriminate removal of its mangrove trees is responsible for the loss of large tracts of mangrove forests, overharvesting of fisheries resources has depleted the river of some valuable fishes that were available from the delta area. Municipal and industrial effluents discharged into the Lyari and Malir rivers and responsible for land-based pollution at the Karachi coast and the harbour. The following are the three major areas receiving land-based pollution and whose environmental conditions have been examined in detail: (l) the Manora channel, located on the estuary of the Lyari river and serving as the main harbour, has vast areas forming its western and eastern backwaters characterized by mud flats and mangroves. The discharge of industrial wastewater from the S.I.T.E. and municipal effluents from the northern and central districts into the Lyari has turned this river into an open drain. This, in turn, has caused a negative impact on the environment of the port, fish harbour, and the adjacent beaches. (2) The Gizri creek receives industrial and municipal effluents from the Malir river as well as from several industries and power stations. The highly degraded discharges from the Malir have negatively impacted the environment in this creek. (3) The coastline between the Manora channel and Gizri creek where the untreated municipal effluents are discharged by the southern districts of Karachi, is responsible for the degraded environment of the Chinna creek, and also of the beaches and the harbour. The Balochistan coast is relatively safe from land-based pollution, mainly because of the lack of industrial, urban or agricultural activity, except the Hingol river system where some agricultural activities have been initiated.

Mercury bioaccumulation in pike (Esox lucius) food chain from Anzali Lagoon, Iran

A number of wide-ranging monitoring studies have been performed in order to estimate the degree of mercury (Hg) contamination in freshwater ecosystems. Knowledge regarding contamination of different levels of the food chain is necessary for estimation of total pollutant input fluxes and subsequent partitioning among different phases in the aquatic system. The growing international concern about this environmental data is closely related to the strongly developing ecological risk assessment activities. In addition,freshwater monitoring outputs hold a key position in the estimation of the Hg dose consumed by the human population as it is highly dependent on fish consumption. So monitoring of Hg in the tissue of edible fish is extremely important because of contaminated fish has caused serious neurological damage to new born babies and adults. Mercury tends to accumulate in fish tissue, particularly, in the form of methyl mercury, which is about 10 times more toxic than inorganic mercury. The Anzali lagoon is one of the biggest wetland of Guilan province, which joins to the Caspian sea. Many Chemical and industrial factories plus agricultural runoffs and urban and rural sewages are major polluting sources of the Anzali wetland. Since many of those polluting sources drain their wastes directly or indirectly into the Anzali wetland and their sewages may be polluted with Hg, this study was conducted to find out the bioaccumulation of Hg bioaccumulation in pike (Esox lucius) food chain from Anzali lagoon, Iran. Sampling were carried out from July 2004 to July 2005, in addition 318 speciments of 9 fish species were collected. T-Hg was measured by LECO AMA 254 Advanced Mercury Analyzer (USA) according to ASTM standard No D-6722. Each sample was analyzed 3 times. Accuracy of T-Hg analysis was checked by running three samples of Standard Reference Materials; SRM 1633b, SRM 2711 & Sra 2709. Detection limit was 0.001 mg/kg in dry weight. The Accuracy degree of analyzor equipment with RSD<%0.05 (N=7) was between %95.5 and %105. In overal eigth fish species were distingushed in the gut content of 87 speciments of pike with age 1-5 year and maximum length 550mm. The max. and min. concentration of T-Hg in dorsal muscle of pjke was 0.2ppm in one year and 1.2ppm in five year class. The mean of T-Hg significantly increased with age and length increased (P<0.05).Mercury accumulation pattern in pike was as well as muscle > liver > spleen (P<0.05). THg content in female was higher than male(P<0.05). In contrast the mean of THg concentration in dorsal muscle of eigth fish species as prey was 0.282, 0.261, 0.328, 0.254, 0.256, 0.286, 0.322 and 0.241 ppm for Carassius auratus gibelio, Hemiculter leucisculus, Blicca bjoerkna transcaucasica, Chalcalburnus mossulensis, Rhodeus sericeus amarus, Gambusia holbrooki, Alburnus charusini hohenackeri & Scardinius Erythrophthalmus respectively.Liner regresion indicated that high degree of relationship between age of pike and Uptak/Intake ratio (R2=%99.12) and indicated that the mercury bioaccumulation in the pike dorsal muscle increased with age increased. BFA was >1 and and indicating the mercury biomagnification in the pike food chain. Trophy level of pike in the Anzali lagoon was estimated as well as 3.5 and 4 . It is generally agreed that Hg concentration in carnivorous fish are higher than in noncarnivorous species.

The present-day fishery of the Uganda waters of Lake Victoria

The Uganda waters of Lake Victoria comprise an area of 28,500 square kilometres with a shore line of 2,380 kilometres extending from the Uganda/Tanzania border in the west to the Uganda/Kenya border in the east. A large part of the Uganda waters of the lake is less than 60 metres deep, waters deeper than 60 metres being on the eastern side of the lake. Thus the Uganda part of the lake is tilted towards the east. A number of rivers drain into the lake from the north and the River Nile flows out of the lake towards the Mediterranean Sea. The Ssese, Kome, Buvuma and Busoga Islands form a very distinctive feature of the lake. These are perhaps the remaining high hills which survived the drowning of the northern valleys during the formation of the lake. In fact, in T. P. O'Brien's book 'The Prehistoric Uganda Protectorate (1939)', Solmon gives a critical summary of the work on the formation of Lake Victoria and shows that the northern part of the lake has numerous drowned valleys, a feature which provides varying habitats for particular species of fish and which may have an effect on the species composition reflected in the catches in different areas along the northern shore of the lake. It is interesting to note that although Lake Victoria as a whole has a number of rivers draining into it, Halbfass (1923) calculated and found that 76 per cent of the water entering the lake is precipitation on the lake surface.

Performance prediction of graphene nanoribbon and carbon nanotube transistors

Carbon nanotubes (CNTs) and graphene nanoribbons (GNRs) field-effect transistor (FET) can be the basis for a quasi-one- dimensional (Q1D) transistor technology. Recent experiments show that the on-off ratio for GNR devices can be improved to level exploration of transistor action is justified. Here we use the tight-binding energy dipersion approximation, to assess the performance of semiconducting CNT and GNR is qualitatively in terms of drain current drive strength, bandgap and density of states for a specified device. By reducing the maximum conductance 4e2/h by half, we observed that our model has a particularly good fit with 50 nm channel single walled carbon nanotube (SWCNT) experimental data. Given the same bandgap, CNTs outperform GNRs due to valley degeneracy. Nevertheless, the variation of the device contacts will decide which transistor will exhibit better conductivity and thus higher ON currents. © 2011 American Institute of Physics.

TRANSIENT SCANNING ELECTRON BEAM ANNEALING METHODS USED TO STUDY DIFFUSION AND DEFECTS IN IMPLANTED SILICON.

Rapid thermal annealing of arsenic and boron difluoride implants, such as those used for source/drain regions in CMOS, has been carried out using a scanning electron beam annealer, as part of a study of transient diffusion effects. Three types of e-beam anneal have been performed, with peak temperatures in the range 900 -1200 degree C; the normal isothermal e-beam anneals, together with sub-second fast anneals and 'dual-pulse' anneals, in which the sample undergoes an isothermal pre-anneal followed by rapid heating to the required anneal temperature is less than 0. 5s. The diffusion occuring during these anneal cycles has been modelled using SPS-1D, an implant and diffusion modelling program developed by one of the authors. This has been modified to incorporate simulated temperature vs. time cycles for the anneals. Results are presented applying the usual equilibrium clustering model, a transient point-defect enhancement to the diffusivity proposed recently by Fair and a new dynamic clustering model for arsenic. Good agreement with SIMS measurements is obtained using the dynamic clustering model, without recourse to a transient defect model.

Conduction bottleneck in silicon nanochain single electron transistors operating at room temperature

Single electron transistors are fabricated on single Si nanochains, synthesised by thermal evaporation of SiO solid sources. The nanochains consist of one-dimensional arrays of ~10nm Si nanocrystals, separated by SiO 2 regions. At 300 K, strong Coulomb staircases are seen in the drain-source current-voltage (I ds-V ds) characteristics, and single-electron oscillations are seen in the drain-source current-gate voltage (I ds-V ds) characteristics. From 300-20 K, a large increase in the Coulomb blockade region is observed. The characteristics are explained using singleelectron Monte Carlo simulation, where an inhomogeneous multiple tunnel junction represents a nanochain. Any reduction in capacitance at a nanocrystal well within the nanochain creates a conduction " bottleneck", suppressing current at low voltage and improving the Coulomb staircase. The single-electron charging energy at such an island can be very high, ~20k BT at 300 K. © 2012 The Japan Society of Applied Physics.

Hot electron field emission via individually transistor-ballasted carbon nanotube arrays.

We present electronically controlled field emission characteristics of arrays of individually ballasted carbon nanotubes synthesized by plasma-enhanced chemical vapor deposition on silicon-on-insulator substrates. By adjusting the source-drain potential we have demonstrated the ability to controllable limit the emission current density by more than 1 order of magnitude. Dynamic control over both the turn-on electric field and field enhancement factor have been noted. A hot electron model is presented. The ballasted nanotubes are populated with hot electrons due to the highly crystalline Si channel and the high local electric field at the nanotube base. This positively shifts the Fermi level and results in a broad energy distribution about this mean, compared to the narrow spread, lower energy thermalized electron population in standard metallic emitters. The proposed vertically aligned carbon nanotube field-emitting electron source offers a viable platform for X-ray emitters and displays applications that require accurate and highly stable control over the emission characteristics.

UV photoconductivity characteristics of ZnO nanowire field effect transistor treated by proton irradiation

We investigated the UV photoconductivity characteristics of ZnO nanowire field effect transistors (FETs) irradiated by proton beams. After proton beam irradiation (using a beam energy of 10 MeV and a fluence of 10 12 cm -2), the drain current and carrier density in the ZnO nanowire FETs decreased, and the threshold voltage shifted to the positive gate bias direction due to the creation of interface traps at the SiO 2/ZnO nanowire interface by the proton beam. The interface traps produced a higher surface barrier potential and a larger depletion region at the ZnO nanowire surface, affecting the photoconductivity and its decay time. The UV photoconductivity of the proton-irradiated ZnO nanowire FETs was higher and more prolonged than that of the pristine ZnO nanowire FETs. The results extend our understanding of the UV photoconductivity characteristics of ZnO nanowire devices and other materials when irradiated with highly energetic particles. © 2012 Elsevier B.V. All rights reserved.

Temperature dependent electron transport in amorphous oxide semiconductor thin film transistors

A temperature-dependent mobility model in amorphous oxide semiconductor (AOS) thin film transistors (TFTs) extracted from measurements of source-drain terminal currents at different gate voltages and temperatures is presented. At low gate voltages, trap-limited conduction prevails for a broad range of temperatures, whereas variable range hopping becomes dominant at lower temperatures. At high gate voltages and for all temperatures, percolation conduction comes into the picture. In all cases, the temperature-dependent mobility model obeys a universal power law as a function of gate voltage. © 2011 IEEE.

Cryogenic single-shot spectroscopy of a floating poly-silicon gate transistor

Trapped electrons, located close to the channel of a transistor, are promising as data storage elements in non-classical information processing. Cryogenic microwave spectroscopy has shown that these electrons give rise to high quality factor resonances in the drain current and a post excitation dynamic behaviour that is related to the system lifetime. Using a floating poly-silicon gate transistor, single shot spectroscopy is performed to characterise the dynamic behaviour during excitation. This behaviour is seen to be dominated by the decay of the transient component, which gives rise to oscillations around the high quality factor resonance. © 2012 American Institute of Physics.

Device and circuit-level performance of carbon nanotube field-effect transistor with benchmarking against a nano-MOSFET

The performance of a semiconducting carbon nanotube (CNT) is assessed and tabulated for parameters against those of a metal-oxide-semiconductor field-effect transistor (MOSFET). Both CNT and MOSFET models considered agree well with the trends in the available experimental data. The results obtained show that nanotubes can significantly reduce the drain-induced barrier lowering effect and subthreshold swing in silicon channel replacement while sustaining smaller channel area at higher current density. Performance metrics of both devices such as current drive strength, current on-off ratio (Ion/Ioff), energy-delay product, and power-delay product for logic gates, namely NAND and NOR, are presented. Design rules used for carbon nanotube field-effect transistors (CNTFETs) are compatible with the 45-nm MOSFET technology. The parasitics associated with interconnects are also incorporated in the model. Interconnects can affect the propagation delay in a CNTFET. Smaller length interconnects result in higher cutoff frequency. © 2012 Tan et al.

Density stratified environments: The double-tank method

We present an alternative method of producing density stratifications in the laboratory based on the 'double-tank' method proposed by Oster (Sci Am 213:70-76, 1965). We refer to Oster's method as the 'forced-drain' approach, as the volume flow rates between connecting tanks are controlled by mechanical pumps. We first determine the range of density profiles that may be established with the forced-drain approach other than the linear stratification predicted by Oster. The dimensionless density stratification is expressed analytically as a function of three ratios: the volume flow rate ratio n, the ratio of the initial liquid volumes λ and the ratio of the initial densities ψ. We then propose a method which does not require pumps to control the volume flow rates but instead allows the connecting tanks to drain freely under gravity. This is referred to as the 'free-drain' approach. We derive an expression for the density stratification produced and compare our predictions with saline stratifications established in the laboratory using the 'free-drain' extension of Oster's method. To assist in the practical application of our results we plot the region of parameter space that yield concave/convex or linear density profiles for both forced-drain and free-drain approaches. The free-drain approach allows the experimentalist to produce a broad range of density profiles by varying the initial liquid depths, cross-sectional and drain opening areas of the tanks. One advantage over the original Oster approach is that density profiles with an inflexion point can now be established. © 2008 Springer-Verlag.