Biogenic amines in Australian animal by-product meals

Biogenic amines were determined in Australian by-product meals including fish meals, poultry meals, meat meals, feather meals and blood meals. They were extracted with 0.1 mol/L HCl, derivatised with dansyl chloride and analysed using HPLC with UV detection at 254 nm. Median levels of putrescine, cadaverine and histamine were determined in the by-product meals, with the ranges being 13-102 mg/kg, 7-220 mg/kg and 4-570 mg/kg, respectively. High levels of biogenic amines were found particularly in fish meals. The results indicate that further studies are required to determine the maximum limits for biogenic amines in by-product meals that will not impair production when fed to poultry.

Functionalized macrocycles from functionalized tetra-amines: Pendent-arm macrocycles derived from dichloropivalic acid

Reaction between ethane-1,2-diamine and 3,3'-dichloropivalic acid results in different, isomeric tetra-amine derivatives, one a tetraamino carboxylic acid and the other a carboxamidotriamino alcohol, depending upon reaction conditions, Intended conversion of the Cu(II) complex of the former to a cyclam-like macrocycle through reaction with nitroethane and formaldehyde results in isolation of derivatives of both the former and the latter. This can be rationalized by assuming the intermediacy of an azetidinone, a species similar to that seen in simpler reactions of dichloropivalates. A single reaction thereby provides pendent-arm macrocycles where one has an electrophilic and the other a nucleophilic substituent. Parallel chemistry is not seen in the reaction between propane-1,3-diamine and 3,3'-dichloropivalate.

Phase separation, porous structure, and cure kinetics in aliphatic epoxy resin containing hyperbranched polyester

Thermosetting blends of an aliphatic epoxy resin and a hydroxyl-functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 4,4'-diaminodiphenylmethane (DDM) as the curing agent. The phase behavior and morphology of the DDM-cured epoxy/HBP blends with HBP content up to 40 wt% were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The cured epoxy/HBP blends are immiscible and exhibit two separate glass transitions, as revealed by DMA. The SEM observation showed that there exist two phases in the cured blends, which is an epoxy-rich phase and an HBP-rich phase, which is responsible for the two separate glass transitions. The phase morphology was observed to be dependent on the blend composition. For the blends with HBP content up to 10 wt%, discrete HBP domains are dispersed in the continuous cured epoxy matrix, whereas the cured blend with 40 wt% HBP exhibits a combined morphology of connected globules and bicominuous phase structure. Porous epoxy thermosets with continuous open structures on the order of 100-300 nm were formed after the HBP-rich phase was extracted with solvent from the cured blend with 40 wt% HBP. The DSC study showed that the curing rate is not obviously affected in the epoxy/HBP blends with HBP content up to 40 wt %. The activation energy values obtained are not remarkably changed in the blends; the addition of HBP to epoxy resin thus does not change the mechanism of cure reaction of epoxy resin with DDM. (c) 2006 Wiley Periodicals, Inc.

Phenols and aromatic amines as thermal stabilizers in polyolefin processing

Scavenging of C- and O-centered free radicals is mandatory in processing stabilization of polypropylene. Phenolic antioxidants act principally as O-radical scavengers only. Aromatic amines, N,N'-disubstituted 1,4-phenylenediamines (PD) and 4,4'disubstituted diphenylamines (DPA), scavenge both C- and O-centered radicals and have consequently a broader activity spectrum. PD cannot be used, however, in polypropylene because of formation of strongly discoloring and staining sacrificial transformation products. Such products formed from DPA have even more discoloring properties. A good processing stability and acceptable extent of discoloration can be achieved by blends of phenols with 4,4'-di-tert.octyl DPA. The effect is considered as a beneficial cooperation between the two chain-breaking antioxidants involving interactions with amine-based transformation products.

Synthesis of substituted 3-anilino-5-phenyl-1,3-dihydro-2H-1,4-benzodiazepine-2-ones and their evaluation as cholecystokinin-ligands

3-Amino-1,4-benzodiazepines as well as chemically related diverse amines were prepared from oxazepam and subsequently screened on the cholecystokinin receptor in a radiolabel binding assay. Oxazepam 2 was activated via its 3-chloro-1,4-benzodiazepine intermediate 3 and was reacted with a large series of aliphatic and aromatic amines. The substituted 3-anilino-1,4-benzodiazepine structure was identified as lead structure in a diverse series of 3-amino-1,4-benzodiazepines 4-38 and the full SAR (structure-activity relationship) optimisation provided 3-anilinobenzodiazepines 16-38 with CCK 1 receptor selectivity to CCK 2. The compounds 18, 24, 28 and 33 have shown affinities at the CCK 1 receptor of 11, 10, 11 and 9 nM, respectively. These equipotent CCK 1 ligands were fully evaluated in behaviour pharmacological essays. An antidepressant effect was identified in the tail suspension- and the Porsolt swimming-test. The ED 50 values for 24 and 28 were determined in these assays as 0.46 and 0.49 mg/kg. The mixed antagonist 37 showed in addition to the antidepressant effects anxiolytic properties. © 2006 Wiley-VCH Verlag GmbH & Co. KGaA.

Dioxaborine dyes as fluorescent probes for amines and carbon nanotubes

The newly synthesized dioxaborine dyes were studied aiming to probe amines and carbon nanotubes, which are potential toxic industrial polluters. To detect the targeted analytes in efficient way, series of ca. 20 dioxaborine dyes were synthesized and tested for reactivity with amines and carbon nanotubes. The most promising result was showed for styryl dye with the fluorescent sensitivity to amines up to 1 ppm. A fluorescent response of the dioxaborine dyes on presence of carbon nanotubes was revealed.

Titanium dioxide photocatalytic degradation of aliphatic ethers and their primary oxidation products

Two studies were performed to obtain fundamental mechanistic information on the TiO2 catalyzed degradation of organic substrates irradiated at 350 nm in dilute aqueous solutions under oxygenated conditions: (a) The photodecomposition of methyl tert-butyl ether (MTBE) and its intermediate products from β-oxidation, 2-methoxy-2-methylpropanol and 2-methoxy-2-methylpropanol. (b) The photodecomposition of two haloethers, bis-(2-chloroethyl) ether, and bis-(2-chloroisopropyl) ether. Controls were carried out throughout the two studies in the absence of light, and without the semiconductor in order to evaluate the role of photolysis. ^ The syntheses of proposed intermediate products, 2-methoxy-2-methylpropanol, 2-methoxy-2-methylpropanal, 2-methoxy-2-methylpropanoic acid, 2-chloroethyl formate, and 1-chloro-2-propyl acetate, were performed. The formation of these products in the titanium dioxide photocatalytic oxidation of the substrates of interest was also confirmed. TiO2 photocatalysis is a very effective method for the mineralization of aliphatic ethers and their primary oxidation products. ^

Reactions of nitrilium salts with indole and pyrrole and their derivatives in the synthesis of imines, ketones and secondary amines

I thank SERC for a CASE studentship (to RG. Giles) with the former Fisons Pharmaceuticals division (with Dr. S. C. Eyley) and Dr. B. R. Buckley, of this department, for provided helpful comments on an earlier version of the manuscript.

Reactions of nitrilium salts with indole and pyrrole and their derivatives in the synthesis of imines, ketones and secondary amines

I thank SERC for a CASE studentship (to RG. Giles) with the former Fisons Pharmaceuticals division (with Dr. S. C. Eyley) and Dr. B. R. Buckley, of this department, for provided helpful comments on an earlier version of the manuscript.

Reactions of nitrilium salts with indole and pyrrole and their derivatives in the synthesis of imines, ketones and secondary amines

I thank SERC for a CASE studentship (to RG. Giles) with the former Fisons Pharmaceuticals division (with Dr. S. C. Eyley) and Dr. B. R. Buckley, of this department, for provided helpful comments on an earlier version of the manuscript.

The use of binary mixtures of 1-butyl-1-methylpyrrolidinium bis{(trifluoromethyl)sulfonyl}imide and aliphatic nitrile solvents as electrolyte for supercapacitors

Abstract The development of high voltage electrolytes is one of the key aspects for increasing both energy and power density of electrochemical double layer capacitors (EDLCs). The usage of blends of ionic liquids and organic solvents has been considered as a feasible strategy since these electrolytes combine high usable voltages and good transport properties at the same time. In this work, the ionic liquid 1-butyl-1-methylpyrrolidinium bis{(trifluoromethyl)sulfonyl}imide ([Pyrr14][TFSI]) was mixed with two nitrile-based organic solvents, namely butyronitrile and adiponitrile, and the resulting blends were investigated regarding their usage in electrochemical double layer capacitors. Both blends have a high electrochemical stability, which was confirmed by prolonged float tests at 3.2 V, as well as, good transport properties. In fact, the butyronitrile blend reaches a conductivity of 17.14 mS·cm−1 and a viscosity of 2.46 mPa·s at 20 °C, which is better than the state-of-the-art electrolyte (1 mol·dm−3 of tetraethylammonium tetrafluoroborate in propylene carbonate).

Binary Mixtures of 1-Butyl-1-Methylpyrrolidinium Bis{(trifluoromethyl)Sulfonyl}Imide and Aliphatic Nitrile Solvents As Electrolyte for Electrochemical Double Layer Capacitors (Invited).

Electrochemical double layer capacitors (EDLCs), also known as supercapacitors, are promising energy storage devices, especially when considering high power applications [1]. EDLCs can be charged and discharged within seconds [1], feature high power (10 kW·kg-1) and an excellent cycle life (>500,000 cycles). All these properties are a result of the energy storage process of EDLCs, which relies on storing energy by charge separation instead of chemical redox reactions, as utilized in battery systems. Upon charging, double layers are forming at the electrode/electrolyte interface consisting of the electrolyte’s ions and electric charges at the electrode surface.In state-of-the-art EDLC systems activated carbons (AC) are used as active materials and tetraethylammonium tetrafluoroborate ([Et4N][BF4]) dissolved in organic solvents like propylene carbonate (PC) or acetonitrile (ACN) are commonly used as the electrolyte [2]. These combinations of materials allow operative voltages up to 2.7 V - 2.8 V and an energy in the order of 5 Wh·kg-1[3]. The energy of EDLCs is dependent on the square of the operative voltage, thus increasing the usable operative voltage has a strong effect on the delivered energy of the device [1]. Due to their high electrochemical stability, ionic liquids (ILs) were thoroughly investigated as electrolytes for EDLCs, as well as, batteries, enabling high operating voltages as high as 3.2 V - 3.5 V for the former [2]. While their unique ionic structure allows the usage of neat ILs as electrolyte in EDLCs, ILs suffer from low conductivity and high viscosity increasing the intrinsic resistance and, as a result, a lower power output of the device. In order to overcome this issue, the usage of blends of ionic liquids and organic solvents has been considered a feasible strategy as they combine high usable voltages, while still retaining good transport properties at the same time.In our recent work the ionic liquid 1-butyl-1-methylpyrrolidinium bis{(trifluoromethyl)sulfonyl}imide ([Pyrr14][TFSI]) was combined with two nitrile-based organic solvents, namely butyronitrile (BTN) and adiponitrile (ADN), and the resulting blends were investing regarding their usage in electrochemical double layer capacitors [4,5]. Firstly, the physicochemical properties were investigated, showing good transport properties for both blends, which are similar to the state-of-the-art combination of [Et4N][BF4] in PC. Secondly, the electrochemical properties for EDLC application were studied in depth revealing a high electrochemical stability with a maximum operative voltage as high as 3.7 V. In full cells these high voltage organic solvent based electrolytes have a good performance in terms of capacitance and an acceptable equivalent series resistance at cut-off voltages of 3.2 and 3.5 V. However, long term stability tests by float testing revealed stability issues when using a maximum voltage of 3.5 V for prolonged time, whereas at 3.2 V no such issues are observed (Fig. 1).Considering the obtained results, the usage of ADN and BTN blends with [Pyrr14][TFSI] in EDLCs appears to be an interesting alternative to state-of-the-art organic solvent based electrolytes, allowing the usage of higher maximum operative voltages while having similar transport properties to 1 mol∙dm-3 [Et4N][BF4] in PC at the same time.