Lovastatin production by Aspergillus terreus using lignocellulose biomass in large scale packed bed reactor

The effect of superficial air velocity on lovastatin production by Aspergillus terreus PL10 using wheat bran and wheat straw was investigated in a 7 l and a 1200 l packed bed reactor. Mass transfer and reaction limitations on bioconversion in the 1200 l reactor was studied based on a central composite design of experiments constructed using the superficial air velocity and solid substrate composition as variables and lovastatin production as response.
The surface response prediction showed a maximum lovastatin production of 1.86 mg g-1 dry substrate on day 5 of the bioconversion process when the reactor was operated using 0.19 vvm airflow rate (23.37 cm min-1 superficial air velocity) and 54% substrate composition (wC). Lovastatin production did not increase significantly with superficial air velocity in the 7 l reactor. Variation in temperature and exit CO2 composition was recorded, and the Damköhler number was calculated for lovastatin production at these two scales. The results showed that in larger reactors mass transfer limitation controlled bioconversion while in smaller reactors bioconversion was controlled by reaction rate limitations. In addition, mass transfer limitations in larger reactors reduced the rate of metabolic heat removal, resulting in hot spots within the substrate bed.

Low loading platinum nanoparticles on reduced graphene oxide-supported tungsten carbide crystallites as a highly active electrocatalyst for methanol oxidation

In this study, low loading platinum nanoparticles (Pt NPs) have been highly dispersed on reduced graphene oxide-supported WC nanocrystallites (Pt-WC/RGO) via program-controlled reduction-carburization technique and microwave-assisted method. The scanning electron microscopy and transmission electron microscopy results show that WC nanocrystallites are homogeneously decorated on RGO, and Pt NPs with a size of ca. 3 nm are dispersed on both RGO and WC. The prepared Pt-WC/RGO is used as an electrocatalyst for methanol oxidation reaction (MOR). Compared with the Pt/RGO, commercial carbon-supported Pt (Pt/C) and PtRu alloy (PtRu/C) electrocatalysts, the Pt-WC/RGO composites demonstrate higher electrochemical active surface area and excellent electrocatalytic activity toward the methanol oxidation, such as better tolerance toward CO, higher peak current density, lower onset potential and long-term stability, which could be attributed to the characterized RGO support, highly dispersed Pt NPs and WC nanocrystallites and the valid synergistic effect resulted from the increased interface between WC and Pt. The present work proves that Pt-WC/RGO composites could be a promising alternative catalyst for direct methanol fuel cells where WC plays the important role as a functional additive in preparing Pt-based catalysts because of its CO tolerance and lower price. 

Micro-abrasion mechanisms of cast CoCrMo in simulated body fluids

The abrasion seen on some of the retrieved CoCrMo hip joints has been reported to be caused by entrained hard particles in vivo. However, little work has been reported on the abrasion mechanisms of CoCrMo alloy in simulated body environments. Therefore. this study covers the mapping of micro-abrasion wear mechanisms of cast CoCrMo induced by third body hard particles under a wide range of abrasive test conditions. This study has a specific focus on covering the possible in vivo wear modes seen on metal-on-metal (MoM) surfaces. Nano-indentation and nano-scratch tests were also employed to further investigate the secondary wear mechanisms-nano-scale material deformation that involved in micro-abrasion processes. This work addresses the potential detrimental effects of third body hard particles in vivo such as increased wear rates (debris generation) and corrosion (metal-ion release). The abrasive wear mechanisms of cast CoCrMo have been investigated under various wear-corrosion conditions employing two abrasives, SiC (similar to 4 mu m) and Al(2)O(3) (similar to 1 mu m), in two test solutions, 0.9% NaCl and 25% bovine serum. The specific wear rates, wear mechanisms and transitions between mechanisms are discussed in terms of the abrasive size, volume fraction and the test solutions deployed. The work shows that at high abrasive volume fractions, the presence of protein enhanced the wear loss due to the enhanced particle entrainment, whereas at much lower abrasive volume fractions, protein reduced the wear loss by acting as a boundary lubricant or rolling elements which reduced the abrasivity (load per particle) of the abrasive particles. The abrasive wear rate and wear mechanisms of the CoCrMo are dependent on the nature of the third body abrasives, their entrainment into the contact and the presence of the proteins. (C) 2009 Elsevier B.V. All rights reserved.

Triterpenoids from Pulsatilla chinensis

A new lupane type triterpenic acid, pulsatillic acid, and two new lupane type triterpenoid glycosides, pulsatilloside A and B, along with the known 23-hydroxybetulinic acid were isolated from the roots of Pulsatilla chinensis. Their structures were characterized as 3-oxo-23-hydroxy-lup-20(29)-en-28-oic acid, 3 beta, 23-dihydroxy-lup-20(29)-en-28-oic acid 3-O-alpha-L-arabinopyranoside and 3 beta, 23-dihydroxy-lup-20(29)-en-28-oic acid 28-O-beta-D-glucopyranosyl-(1-->6)-beta-D-glucopyranoside on the basis of hydrolysis and spectral evidence including two-dimensional relay HOHAHA, one-dimensional multiple relay COSY and ROESY NMR techniques. Pulsatillic acid exhibited cytotoxic activities against P-388, Lewis lung carcinoma and human large-cell lung carcinoma.

PATENSIN, A SAPONIN FROM PULSATILLA PATENS VAR MULTIFIDA

Patensin, a new triterpenoid glycoside, was isolated from the ethanolic extraction of the roots of Pulsatilla patens var. multifida. Its structure was established as hederagenin 3-O-beta-D-galactopyranosyl-(1-->2)-beta-D-glucopyranoside on the basis of hydrolysis and spectral evidence including 1D and 2D NMR techniques.

Methanol electro-oxidation on platinum modified tungsten carbides in direct methanol fuel cells: a DFT study

In exploration of low-cost electrocatalysts for direct methanol fuel cells (DMFCs), Pt modified tungsten carbide (WC) materials are found to be great potential candidates for decreasing Pt usage whilst exhibiting satisfactory reactivity. In this work, the mechanisms, onset potentials and activity for electrooxidation of methanol were studied on a series of Pt-modified WC catalysts where the bare W-terminated WC(0001) substrate was employed. In the surface energy calculations of a series of Pt-modified WC models, we found that the feasible structures are mono- and bi-layer Pt-modified WCs. The tri-layer Pt-modified WC model is not thermodynamically stable where the top layer Pt atoms tend to accumulate and form particles or clusters rather than being dispersed as a layer. We further calculated the mechanisms of methanol oxidation on the feasible models via methanol dehydrogenation to CO involving C-H and O-H bonds dissociating subsequently, and further CO oxidation with the C-O bond association. The onset potentials for the oxidation reactions over the Pt-modified WC catalysts were determined thermodynamically by water dissociation to surface OH* species. The activities of these Pt-modified WC catalysts were estimated from the calculated kinetic data. It has been found that the bi-layer Pt-modified WC catalysts may provide a good reactivity and an onset oxidation potential comparable to pure Pt and serve as promising electrocatalysts for DMFCs with a significant decrease in Pt usage.

Multilayered micro/nanocrystalline CVD diamond coatings for biotribology

In the present work multilayered micro/nanocrystalline (MCD/NCD) diamond coatings were developed by Hot Filament Chemical Vapour Deposition (HFCVD). The aim was to minimize the surface roughness with a top NCD layer, to maximize adhesion onto the Si3N4 ceramic substrates with a starting MCD coating and to improve the mechanical resistance by the presence of MCD/NCD interfaces in these composite coatings. This set of features assures high wear resistance and low friction coefficients which, combined to diamond biocompatibility, set this material as ideal for biotribological applications. The deposition parameters of MCD were optimized using the Taguchi method, and two varieties of NCD were used: NCD-1, grown in a methane rich gas phase, and NCD-2 where a third gas, Argon, was added to the gas mixture. The best combination of surface pre-treatments in the Si3N4 substrates is obtained by polishing the substrates with a 15 μm diamond slurry, further dry etching with CF4 plasma for 10 minutes and final ultrasonic seeding in a diamond powder suspension in ethanol for 1 hour. The interfaces of the multilayered CVD diamond films were characterized with high detail using HRTEM, STEM-EDX and EELS. The results show that at the transition from MCD to NCD a thin precursor graphitic film is formed. On the contrary, the transition of the NCD to MCD grade is free of carbon structures other than diamond, as a result of the richer atomic hydrogen content and of the higher substrate temperature for MCD deposition. At those transitions, WC nanoparticles were found due to contamination from the filament, being also present at the first interface of the MCD layer with the silicon nitride substrate. In order to study the adhesion and mechanical resistance of the diamond coatings, indentation and particle jet blasting tests were conducted, as well as tribological experiments with homologous pairs. Indentation tests proved the superior behaviour of the multilayered coatings that attained a load of 800 N without delamination, when compared to the mono and bilayered ones. The multilayered diamond coatings also reveal the best solid particle erosion resistance, due to the MCD/NCD interfaces that act as crack deflectors. These results were confirmed by an analytical model on the stress field distribution based on the von Mises criterion. Regarding the tribological testing under dry sliding, multilayered coatings also exhibit the highest critical load values (200N for Multilayers with NCD-2). Low friction coefficient values in the range μ=0.02- 0.09 and wear coefficient values in the order of ~10-7 mm3 N-1 m-1 were obtained for the ball and flat specimens indicating a mild wear regime. Under lubrication with physiological fluids (HBSS e FBS), lower wear coefficient values ~10-9-10-8 mm3 N-1 m-1) were achieved, governed by the initial surface roughness and the effective contact pressure.

The relation of body mass index and abdominal adiposity with dyslipidemia in 27 general populations of the WHO MONICA Project.

The association between adiposity measures and dyslipidemia has seldom been assessed in a multipopulational setting. 27 populations from Europe, Australia, New Zealand and Canada (WHO MONICA project) using health surveys conducted between 1990 and 1997 in adults aged 35-64 years (n = 40,480). Dyslipidemia was defined as the total/HDL cholesterol ratio >6 (men) and >5 (women). Overall prevalence of dyslipidemia was 25% in men and 23% in women. Logistic regression showed that dyslipidemia was strongly associated with body mass index (BMI) in men and with waist circumference (WC) in women, after adjusting for region, age and smoking. Among normal-weight men and women (BMI<25 kg/m(2)), an increase in the odds for being dyslipidemic was observed between lowest and highest WC quartiles (OR = 3.6, p < 0.001). Among obese men (BMI ≥ 30), the corresponding increase was smaller (OR = 1.2, p = 0.036). A similar weakening was observed among women. Classification tree analysis was performed to assign subjects into classes of risk for dyslipidemia. BMI thresholds (25.4 and 29.2 kg/m(2)) in men and WC thresholds (81.7 and 92.6 cm) in women came out at first stages. High WC (>84.8 cm) in normal-weight men, menopause in women and regular smoking further defined subgroups at increased risk. standard categories of BMI and WC, or their combinations, do not lead to optimal risk stratification for dyslipidemia in middle-age adults. Sex-specific adaptations are necessary, in particular by taking into account abdominal obesity in normal-weight men, post-menopausal age in women and regular smoking in both sexes.

The White Cane Magazine, Fall 2013, Vol. 4, no. 3

Quarterly newsletter produced by the Iowa Department of Blind, about the information and activities that are on going in the department.

The White Cane Magazine, Spring 2013, Vol. 4, no. 2

Quarterly newsletter produced by the Iowa Department of Blind, about the information and activities that are on going in the department.

[Phot. d'un groupe en Norvège (Brudepiger paa Vos), don E. Reclus en 1886]

Donateur : Reclus, Élisée (1830-1905)

[2 phot. de Zuckmantel (Cuckmantl) par J. Springer et Josef Fietz, phot. à Freiwaldau (Fryvaldov), don Alexander Jawornicki en 1889]

Donateur : Jawornicki, Alexandre (18..-19..?)