A novel water-soluble hydrophobically associating polyacrylamide based on oleic imidazoline and sulfonate for enhanced oil recovery

3-(2-(2-Heptadec-8-enyl-4,5-dihydro-imidazol-1-yl)ethylcarbamoyl)acrylic acid (NIMA), 3-(diallyl-amino)-2-hydroxypropyl sulfonate (NDS), acrylamide (AM) and acrylic acid (AA) were successfully utilized to prepare novel acrylamide-based copolymers (named AM/AA/NIMA and AM/AA/NDS/NIMA) which were functionalized by a combination of imidazoline derivative and/or sulfonate via redox free-radical polymerization. The two copolymers were characterized by infrared (IR) spectroscopy, 1H nuclear magnetic resonance (1H NMR), viscosimetry, pyrene fluorescence probe, thermogravimetry (TG) and differential thermogravimetry (DTG). As expected, the polymers exhibited excellent thickening property, shear stability (viscosity retention rate 5.02% and 7.65% at 1000 s-1) and salt-tolerance (10:000 mg L-1 NaCl: viscosity retention rate up to 17.1% and 10.2%) in comparison with similar concentration partially hydrolyzed polyacrylamide (HPAM). The temperature resistance of the AM/AA/NDS/NIMA solution was also remarkably improved and the viscosity retention rate reached 54.8% under 110 °C. According to the core flooding tests, oil recovery could be enhanced by up to 15.46% by 2000 mg L-1 of the AM/AA/NDS/NIMA brine solution at 80 °C.

Pore pressure effect on slope stability assessment

Slope stability assessment has been an integral problem for geotechnical engineering all these years. While stability of slopes is affected by various factors, pore pressure is one of the common naturalelements that influence slope stability analysis. This paper studies the effect of pore pressure on slope stability assessment by using Limit Equilibrium Method (LEM). The results will be compared to the solutions of Hoek and Bray charts. In this study, slopes with different levels of water table corresponding to those of Hoek and Bray charts are investigated. It’s interesting to observe that the results obtained from the Hoek and Bray charts yielded different factor of safety compare to those in the study here-in. In fact, the different between the factors of safety could be up to 30%. Hence this issue should be taken into consideration during slope design.

Enhanced stabilization of aerosol-OT surfactant monolayer upon interaction with small amounts of bovine serum albumin at the air-water interface

An investigation is made of the influence from small amounts of the protein bovine serum albumin (BSA) on the lateral organization of low molecular weight surfactant sodium bis-2-ethylhexyl sulfosuccinate (AOT) at the air-water interface. Surface pressure (pi - A), surface potential (DeltaV - A) and Brewster angle microscopy (BAM) experiments were carried out, with particular emphasis on the monolayer stability under successive compression-expansion cycles. AOT monolayer is not stable at the air-water interface, which means that the majority of AOT molecules go into the aqueous subphase as monomers and/or normal micelles. When a waiting time elapses between spreading and compression, the surfactant monolayer tends to reorganize partially at the air-water interface, with a monolayer expansion being observed for waiting times as large as 12 h. The incorporation of very small amount of BSA (10(-9) M) at the interface, also inferred from BAM, increases the monolayer stability as revealed by pi - A and DeltaV - A results. For a waiting time of circa 3 h, the mixed monolayer reaches its maximum stability. This must be related to protein (and/or protein-surfactant complexes) adsorbed onto the AOT monolayer, thus altering the BSA conformation to accommodate its hydrophobic/hydrophilic residues. Furthermore, the effects from such small amounts of BSA in the monolayer formation and stabilization mean that the AOT monolayer responds cooperatively to BSA. (C) 2004 Elsevier B.V. All rights reserved.

DFT study of the water-assisted tautomerization process between hydrated oxide, MO(H2O)(+), and dihydroxide, M(OH)(2)(+) cations (M = V, Nb and Ta)

Density functional theory (DFT) calculations point out that the participation of water can effectively lower the barrier height for the isomerization process between hydrated oxide cation, MO(H2O)(+), and dihydroxide cation, M(OH)(2)(+), (M = V, Nb and Ta). The catalytic effect is achieved by a water-assisted mechanism in which water acts as proton donor and acceptor, via a transition structure corresponding to a six-membered ring. In the case of vanadium atom, the presence of two water molecules has been taken into account and the tautomerization becomes nearly barrierless, decreasing both the stability of the transition structures relative to intermediates and the depths of wells associated with the intermediates. (C) 2003 Elsevier B.V. All rights reserved.

COLOR STABILITY of SEALED COMPOSITE RESIN RESTORATIVE MATERIALS AFTER ULTRAVIOLET ARTIFICIAL AGING and IMMERSION IN STAINING SOLUTIONS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

12-Month color stability of enamel, dentine, and enamel-dentine samples after bleaching

The study aimed to quantify the color regression of enamel (E), dentine (D), and combined enamel-dentine (ED) of differently bleached ED specimens over a period of 12 months in vitro. Two ED samples were obtained from the labial surfaces of bovine teeth and prepared to a standardized thickness with the enamel and dentine layer each 1 mm. The ED samples were distributed on four groups (each n=80), in which the different bleaching products were applied on enamel (1, Whitestrips; 2, Illumine 15%; 3, Opalescence Xtra Boost) or dentine surfaces (4, mixture of sodium perborate/distilled water). Eighty ED samples were not bleached (control). Color (L*a*b*) of ED was assessed at baseline, subsequently after bleaching and at 3, 6, and 12 months of storage after bleaching (each 20 samples/group). E and D samples were prepared by removing the dentine or enamel layer of ED samples to allow for separate color analysis. Bleaching resulted in a significant color change (Delta E) of ED specimens. Within the observation period, Delta L but not Delta b declined to baseline. L* values of E and D samples also declined and were not significantly different from control samples after 12 months, while b* values did not decrease to baseline. Generally, no differences between the bleaching agents could be observed. Color change of enamel, dentine, and combined ED of in vitro bleached tooth samples is not stable over time with regard to lightness. However, yellowness did not return to baseline within 1 year.

Influence of microwave disinfection on the dimensional stability of intact and relined acrylic resin denture bases

Statement of problem. Microwave irradiation has been suggested as a method to disinfect denture bases. However, the effect of microwave heating on the dimensional stability of the relined denture bases is unknown.Purpose. The purpose of this study was to evaluate the dimensional stability of intact and relined acrylic resin denture bases after microwave disinfection.Material and methods. A standard brass cast simulating an edentulous maxillary arch was machined and used to fabricate 2- and 4-mm-thick denture bases (n=200), which were processed with heat-polymerized acrylic resin (Lucitone 550). The 2-mm thick-specimens (n=160) were relined with 2 mm of autopolymerizing resin (Tokuso Rebase Fast, Ufi Gel Hard, Kooliner, or New Truliner). Distances between 5 removable pins on the standard brass cast were measured with a Nikon optical comparator, and the area (mm(2)) formed by the distance between 5 pins was calculated and served as baseline. During fabrication, the pins were transferred to the intaglio surface of the specimens. Differences between the baseline area and those subsequently determined for the specimens were used to calculate the percent dimensional changes. The intact and relined denture bases were divided into 4 groups (n=10) and evaluated after: polymerization (control group P); 1 cycle of microwave disinfection (MW); daily microwave disinfection for 7 days (control group MW7); water storage for 7 days (WS7). Microwave irradiation was performed for 6 minutes at 650 W. Data were analyzed using 2-way ANOVA followed by Tukey's test (alpha=.05).Results. Intact specimens and those relined with Kooliner and New Truliner showed increased shrinkage after 1 (P=.05, .018, and .001, respectively) and 7 (P <.001, .003, and <.001, respectively) cycles of microwave disinfection. With the exception of specimens relined with Kooliner, intact specimens showed greater shrinkage than the relined specimens after 7 cycles of microwave disinfection.Conclusions. Microwave disinfection produced increased shrinkage of intact specimens and those relined with New Truliner and Kooliner.

Shear Bond Strength of Different Repair Systems to Titanium After Water Aging

This study evaluated the shear bond strength (SBS) and stability of commercially pure titanium (CP Ti)/repair material interfaces promoted by different repair systems. One hundred CP Ti cast discs were divided into five repair system groups: 1) Epricord (EP); 2) Bistite 11 DC (BT); 3) Cojet (CJ); 4) Scotchbond Multi-Purpose Plus (SB) (control group); and 5) Cojet Sand plus Scotchbond Multi-Purpose Plus (CJSB). The specimens were stored in distilled water for 24 hours at 37 degrees C, thermal cycled (5000 cycles, 5 degrees-55 degrees C) and stored under the same conditions for either 24 hours or six months (n=10). SBS was tested and the data were analyzed by two-way analysis of variance (ANOVA) and Tukey test (alpha=.05). Failure mode was determined with a stereomicroscope (20x). The repair system, storage time, and their interaction significantly affected the SBS (p<0.001). At 24 hours, CJSB exhibited the highest SBS value, followed by CJ. At six months, these two groups had similar mean SBS (p>0.05) and higher means in comparison to the other groups. For both storage times, BT presented the lowest SBS, while the EP and SB groups did not differ significantly from one another (p>0.05). There were no significant differences in SBS between the storage times for the groups EP and CJ (p>0.05). The groups BT, SB, and CJSB showed 100% adhesive failure, irrespective of storage time. The CJSB group showed the highest SBS at both storage times. At six months, the CJ group exhibited a similar SBS mean value when compared to the CJSB group. Water storage adversely affected the groups BT, SB (control group), and CJSB. Considering SBS values, stability, and the failure mode simultaneously, the CJ group showed the best CP Ti repair performance.

Flexural strength of acrylic resin repairs processed by different methods: water bath, microwave energy and chemical polymerization

Denture fractures are common in daily practice, causing inconvenience to the patient and to the dentists. Denture repairs should have adequate strength, dimensional stability and color match, and should be easily and quickly performed as well as relatively inexpensive. Objective: The aim of this study was to evaluate the flexural strength of acrylic resin repairs processed by different methods: warm water-bath, microwave energy, and chemical polymerization. Material and methods: Sixty rectangular specimens (31x10x2.5 mm) were made with warm water-bath acrylic resin (Lucitone 550) and grouped (15 specimens per group) according to the resin type used to make repair procedure: 1) specimens of warm water-bath resin (Lucitone 550) without repair (control group); 2) specimens of warm water-bath resin repaired with warm water-bath; 3) specimens of warm water-bath resin repaired with microwave resin (Acron MC); 4) specimens of warm water-bath resin repaired with autopolymerized acrylic resin (Simplex). Flexural strength was measured with the three-point bending in a universal testing machine (MTS 810 Material Test System) with load cell of 100 kgf under constant speed of 5 mm/min. Data were analyzed statistically by Kruskal-Wallis test (p<0.05). Results: The control group showed the best result (156.04 +/- 1.82 MPa). Significant differences were found among repaired specimens and the results were decreasing as follows: group 3 (43.02 +/- 2.25 MPa), group 2 (36.21 +/- 1.20 MPa) and group 4 (6.74 +/- 0.85 MPa). Conclusion: All repaired specimens demonstrated lower flexural strength than the control group. Repairs with autopolymerized acrylic resin showed the lowest flexural strength.

Ballast water: a review of the impact on the world public health

Since the nineteenth century ships have been using ballast water (BW) for safety, stability, propulsion and maneuverability, as well as to redress loss of fuel weight and water consumption, and to maintain structural stress at acceptable levels. Ballast water has been spreading many non-native species around the globe, but little is known about the extent and potential significance of ship-mediated transfer of microorganisms. The global movements of ballast water by ships create a long-distance dispersal mechanism for human pathogens that may be important in the worldwide distribution of microorganisms, as well as for the epidemiology of waterborne diseases. Only a few studies have been carried out on this subject, most of them involving ballast water containing crustacean larvae and phytoplankton. Specialized microbiological studies on these waters are necessary to avoid a repeat of what happened in 1991, when epidemic cholera was reported in Peru and rapidly spread through Latin America and Mexico. In July of 1992, Vibrio cholerae was found in the USA and the Food and Drug Administration (FDA) determined that it came from ballast water of ships whose last port of call was in South America. In Brazil, just a few studies about the subject have been performed. An exploratory study by the Brazilian National Health Surveillance Agency (Agencia Nacional de Vigilancia Sanitaria - ANVISA) found in ballast water different microorganisms, such as fecal coliforms, Escherichia coli, Enterococcus faecalis, Clostridium perfringens, coliphages, Vibrio cholerae O1 and Vibrio cholerae non-O1. Until now, Brazil has been focusing only on organisms transported to its territory from other countries by ballast water, to avoid their establishment and dissemination in Brazilian areas. Studies that can assess the probability that water ballast carries pathogenic microorganisms are extremely important, as is the examination of ships that arrive in the country. Treatment of the human infections caused by BW exists but none is completely safe and efficient.

INFLUENCE of ENCAPSULATING MATERIALS on WATER SORPTION ISOTHERMS of VACUUM-DRIED PERSIMMON PULP POWDER

Water sorption isotherms for vacuum-dried persimmon pulp (PP) powder were determined in the temperature range of 20-50C, and the effects of maltodextrin (MD) or gum arabic (GA) addition on the water sorption behavior of the dried powders were analyzed. Several models were evaluated to fit the experimental data and the Guggenheim-Anderson-de Boer model was selected as the most adequate to describe the observed behavior. Addition of encapsulants affected the isotherms: at the same water activity, PP powder with added GA (PP + GA) or MD (PP + MD) presented lower equilibrium water content than pure PP and were less affected by temperature variations. Samples of PP + MD presented lower equilibrium moisture content than those of PP + GA. The isosteric heats of sorption of pulp powders with encapsulants were higher (less negative) than those of PP, suggesting that there are more active polar sites in PP than in pulp powder containing encapsulants.PRACTICAL APPLICATIONSThe choice of persimmon to carry out this work was due to the large persimmon production available in Brazil; moreover, persimmon pulp is rich in vitamin C, vitamin A and iron, as well as in phenolic compounds. Drying of fruit pulps with high sugar content presents technical difficulties because the hygroscopicity and thermoplasticity of the resulting powders when exposed to high temperature and relative humidity. For this reason, addition of high-molar-mass biopolymers, such as maltodextrin or gum arabic, is a strategy to aid drying and to improve storage stability. Knowledge of water sorption isotherms and net isosteric heats of sorption is important to various food processing operations, including drying, storage and packaging. They are useful in calculating time and energy consumptions during drying, modeling moisture changes during storage and predicting shelf life of food products.

Effect of water renewal on dominance hierarchy of juvenile Nile tilapia

RECAW - CNPq

The effect of sodium chloride on the formation of W/O microemulsions in soy bean oil/surfactant/water systems and the solubilization of small hydrophilic molecules

Partial pseudoternary phase diagrams were constructed for soy bean oil (SBO)/surfactant/NaCl aqueous solution systems, at 25 degrees C, using the anionic sodium bis(2-ethylhexyl) sulfosuccinate (ACT) and zwiterionic phosphatidylcholine (PC) or mixtures of these surfactants. The isotropic single phase of water-in-oil (W/O) microemulsions (MEs) is shown in the phase diagram and their viscosity reported. ME samples containing small amount of surfactant exhibit slightly higher viscosity than pure SBO, and were used in the solubilization of small water soluble molecules. NaCl enhances the area of the ME phase and MEs with different surfactant composition exhibit different induction time as obtained from tests of oxidative stability, and so are the MEs enriched with ascorbic acid, folic acid and FeSO4, with the latter exhibiting lower stability. The so prepared enriched soy bean oil has potential application in food industry since the surfactants are food grade. (C) 2007 Elsevier B.V. All rights reserved.

The water factor in the protein-folding problem

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal behavior of residues (sludge) originated from Araraquara water and sewage treatment station

The number of the cities with canalized water and sewage treatment stations has increased lately and consequently having in mind the great concern on environment preservation and the quality of the water used by society. However, these stations are nowadays causing another kind of problem: a huge quantity of sludge as residue. Due to the implication of the residue on the environment and, consequently, to human life quality, performing of an accurate investigation about the components of such sludge, as well as the thermal stability of this residue in the environment become necessary. This paper presents a study on sludge from water and sewage treatment station, as well as the thermal characterization of residue. Such study was performed through FTIR, atomic absorption, thermoanalytical (TG/DTG, DTA) techniques, that made it possible to observe that the main components of the sludge are clay, carbonates and organic substance, presenting a low rate of metals and a unique thermal behavior since the sludge from the treatment station has a higher thermal stability.