Impacts on Safety of Left-Turn Treatment at High Speed Signalized Intersections, HR-347, 1994

Left-turning traffic is a major source of conflicts at intersections. Though an average of only 10% to 15% of all approach traffic turns left, these vehicles are involved in approximately 45% of all accidents. This report presents the results of research conducted to develop models which estimate approach accident rates at high speed signalized intersections. The objective of the research was to quantify the relationship between traffic and intersection characteristics, and accident potential of different left turn treatments. Geometric, turning movement counts, and traffic signal phasing data were collected at 100 intersections in Iowa using a questionnaire sent to municipalities. Not all questionnaires resulted in complete data and ultimately complete data were derived for 63 intersections providing a database of 248 approaches. Accident data for the same approaches were obtained from the Iowa Department of Transportation Accident Location and Analysis System (ALAS). Regression models were developed for two different dependent variables: 1) the ratio of the number of left turn accidents per approach to million left turning vehicles per approach, and 2) the ratio of accidents per approach to million traffic movements per approach. A number of regression models were developed for both dependent variables. One model using each dependent variable was developed for intersections with low, medium, and high left turning traffic volumes. As expected, the research indicates that protected left turn phasing has a lower accident potential than protected/permitted or permitted phasing. Left turn lanes and multiple lane approaches are beneficial for reducing accident rates, while raised medians increase the likelihood of accidents. Signals that are part of a signal system tend to have lower accident rates than isolated signals. The resulting regression models may be used to determine the likely impact of various left turn treatments on intersection accident rates. When designing an intersection approach, a traffic engineer may use the models to estimate the accident rate reduction as a result of improved lane configurations and left turn treatments. The safety benefits may then be compared to any costs associated with operational effects to the intersection (i.e., increased delay) to determine the benefits and costs of making intersection safety improvements.

Methods of Jet to Wire Speed Ratio Determination and Its Effect in Paper and Board Manufacture

Suihku/viira-nopeussuhde on perälaatikon huulisuihkun ja viiran välinen nopeusero. Se vaikuttaa suuresti paperin ja kartongin loppuominaisuuksiin, kuten formaatioon sekä kuituorientaatioon ja näin ollen paperin lujuusominaisuuksiin. Tämän johdosta on erityisen tärkeää tietää todellinen suihku/viira-nopeussuhde paperin- ja kartonginvalmistuksessa. Perinteinen suihku/viira-nopeussuhteen määritysmenetelmä perustuu perälaatikon kokonaispaineeseen. Tällä menetelmällä kuitenkin todellinen huulisuihkun nopeus saattaa usein jäädä tietämättä johtuen mahdollisesta virheellisestä painemittarin kalibroinnista sekä laskuyhtälön epätarkkuuksista. Tämän johdosta on kehitetty useita reaaliaikaisia huulisuihkun mittausmenetelmiä. Perälaatikon parametrien optimaaliset asetukset ovat mahdollista määrittää ja ylläpitää huulisuihkun nopeuden “on-line” määrityksellä. Perälaatikon parametrejä ovat mm. huulisuihku, huuliaukon korkeusprofiili, reunavirtaukset ja syöttövirtauksen tasaisuus. Huulisuihkun nopeuden on-line mittauksella paljastuu myös muita perälaatikon ongelmakohtia, kuten mekaaniset viat, joita on perinteisesti tutkittu aikaa vievillä paperin ja kartongin lopputuoteanalyyseillä.

Progressive multifocal leukoencephalopathy in common variable immunodeficiency: mitigated course under mirtazapine and mefloquine.

Demonstration of survival and outcome of progressive multifocal leukoencephalopathy (PML) in a 56-year-old patient with common variable immunodeficiency, consisting of severe hypogammaglobulinemia and CD4+ T lymphocytopenia, during continuous treatment with mirtazapine (30 mg/day) and mefloquine (250 mg/week) over 23 months. Regular clinical examinations including Rankin scale and Barthel index, nine-hole peg and box and block tests, Berg balance, 10-m walking tests, and Montreal Cognitive Assessment (MoCA) were done. Laboratory diagnostics included complete blood count and JC virus (JCV) concentration in cerebrospinal fluid (CSF). The noncoding control region (NCCR) of JCV, important for neurotropism and neurovirulence, was sequenced. Repetitive MRI investigated the course of brain lesions. JCV was detected in increasing concentrations (peak 2568 copies/ml CSF), and its NCCR was genetically rearranged. Under treatment, the rearrangement changed toward the archetype sequence, and later JCV DNA became undetectable. Total brain lesion volume decreased (8.54 to 3.97 cm(3)) and atrophy increased. Barthel (60 to 100 to 80 points) and Rankin (4 to 2 to 3) scores, gait stability, and box and block (7, 35, 25 pieces) and nine-hole peg (300, 50, 300 s) test performances first improved but subsequently worsened. Cognition and walking speed remained stable. Despite initial rapid deterioration, the patient survived under continuous treatment with mirtazapine and mefloquine even though he belongs to a PML subgroup that is usually fatal within a few months. This course was paralleled by JCV clones with presumably lower replication capability before JCV became undetectable. Neurological deficits were due to PML lesions and progressive brain atrophy.

Approximate solution to the speed of spreading viruses

Recently, it has been shown that the speed of virus infections can be explained by time-delayed reactiondiffusion [J. Fort and V. Me´ndez, Phys. Rev. Lett. 89, 178101 (2002)], but no analytical solutions were found. Here we derive formulas for the front speed, valid in appropriate limits. We also integrate numerically the evolution equations of the system. There is good agreement with both numerical and experimental speeds

Design and Simulation of High-Speed Rotating Electrical Machinery

Global energy consumption has been increasing yearly and a big portion of it is used in rotating electrical machineries. It is clear that in these machines energy should be used efficiently. In this dissertation the aim is to improve the design process of high-speed electrical machines especially from the mechanical engineering perspective in order to achieve more reliable and efficient machines. The design process of high-speed machines is challenging due to high demands and several interactions between different engineering disciplines such as mechanical, electrical and energy engineering. A multidisciplinary design flow chart for a specific type of high-speed machine in which computer simulation is utilized is proposed. In addition to utilizing simulation parallel with the design process, two simulation studies are presented. The first is used to find the limits of two ball bearing models. The second is used to study the improvement of machine load capacity in a compressor application to exceed the limits of current machinery. The proposed flow chart and simulation studies show clearly that improvements in the high-speed machinery design process can be achieved. Engineers designing in high-speed machines can utilize the flow chart and simulation results as a guideline during the design phase to achieve more reliable and efficient machines that use energy efficiently in required different operation conditions.

Real-time monitoring of laser scribing process utilizing high-speed camera

Currently, laser scribing is growing material processing method in the industry. Benefits of laser scribing technology are studied for example for improving an efficiency of solar cells. Due high-quality requirement of the fast scribing process, it is important to monitor the process in real time for detecting possible defects during the process. However, there is a lack of studies of laser scribing real time monitoring. Commonly used monitoring methods developed for other laser processes such a laser welding, are sufficient slow and existed applications cannot be implemented in fast laser scribing monitoring. The aim of this thesis is to find a method for laser scribing monitoring with a high-speed camera and evaluate reliability and performance of the developed monitoring system with experiments. The laser used in experiments is an IPG ytterbium pulsed fiber laser with 20 W maximum average power and Scan head optics used in the laser is Scanlab’s Hurryscan 14 II with an f100 tele-centric lens. The camera was connected to laser scanner using camera adapter to follow the laser process. A powerful fully programmable industrial computer was chosen for executing image processing and analysis. Algorithms for defect analysis, which are based on particle analysis, were developed using LabVIEW system design software. The performance of the algorithms was analyzed by analyzing a non-moving image from the scribing line with resolution 960x20 pixel. As a result, the maximum analysis speed was 560 frames per second. Reliability of the algorithm was evaluated by imaging scribing path with a variable number of defects 2000 mm/s when the laser was turned off and image analysis speed was 430 frames per second. The experiment was successful and as a result, the algorithms detected all defects from the scribing path. The final monitoring experiment was performed during a laser process. However, it was challenging to get active laser illumination work with the laser scanner due physical dimensions of the laser lens and the scanner. For reliable error detection, the illumination system is needed to be replaced.

Towards a better understanding of the relationship between speed of internationalization and performance outcomes among young international ventures

This thesis offers an explanation for the inconsistent relationship between speed of internationalization and performance outcomes in the context of young international ventures. We argue that the variables of scope of internationalization, entrepreneurial orientation and degree of internationalization play a moderating role in the relationship between speed of internationalization and performance outcomes of international new ventures (INVs). Using primary survey data from INVs in China, we found empirical support for significant moderating impact of scope of internationalization, entrepreneurial orientation variables and no support for the moderating impact of degree of internationalization variable. The results suggest that business managers of INVs shall consider the applied moderating variables as an effective tool kit to enhance firm performance in foreign markets and to mitigate any potential risks of early internationalization.

Procés de destintatge del paper per flotació. Avaluació de l'eficàcia de l'eliminació de tinta

La tesi doctoral presentada té com a objectius principals l'estudi de les etapes fonamentals de desintegració i flotació en un procés de destintatge de papers vell de qualitats elevades per a poder millorar l'eficàcia d'aquestes etapes clau. Conté una revisió teòrica completa i molt actualitzada del procés de desintegració i flotació tant a nivell macroscòpic com microscòpic. La metodologia de treball en el laboratori, la posada a punt dels aparells, així com les anàlisis efectuades per a valorar la resposta del procés (anàlisi de blancor, anàlisi d'imatge i anàlisi de la concentració efectiva de tinta residual) estan descrites en el capítol de material i mètodes. La posada en marxa permet obtenir unes primeres conclusions respecte la necessitat de treballar amb una matèria primera homogènia i respecte la no significació de la temperatura de desintegració dins l'interval de treball permès al laboratori (20-50°C). L'anàlisi de les variables mecàniques de desintegració: consistència de desintegració (c), velocitat d'agitació en la desintegració (N) i temps de desintegració (t), permet de discernir que la consistència de desintegració és una variable fonamental. El valor de consistència igual al 10% marca el límit d'existència de les forces d'impacte mecànic en la suspensió fibrosa. A consistències superiors, les forces viscoses i d'acceleració dominen l'etapa de desintegració. Existeix una interacció entre la consistència i el temps de desintegració, optimitzant-se aquesta darrera variable en funció del valor de la consistència. La velocitat d'agitació és significativa només per a valors de consistència de desintegració inferiors al 10%. En aquests casos, incrementar el valor de N de 800 a 1400 rpm representa una disminució de 14 punts en el factor de destintabilitat. L'anàlisi de les variables químiques de desintegració: concentració de silicat sòdic (% Na2SiO3), peròxid d'hidrogen (% H2O2) i hidròxid sòdic (% Na2OH), proporciona resultats força significatius. El silicat sòdic presenta un efecte altament dispersant corroborat per les corbes de distribució dels diàmetres de partícula de tinta obtingudes mitjançant anàlisi d'imatges. L'hidròxid sòdic també presenta un efecte dispersant tot i que no és tant important com el del silicat sòdic. Aquests efectes dispersants són deguts principalment a l'increment de les repulsions electrostàtiques que aporten a la suspensió fibrosa aquests reactius químics fent disminuir l'eficàcia d'eliminació de l'etapa de flotació. El peròxid d'hidrogen utilitzat generalment com agent blanquejant, actua en aquests casos com a neutralitzador dels grups hidroxil provinents tant del silicat sòdic com de l'hidròxid sòdic, disminuint la repulsió electrostàtica dins la suspensió. Amb l'anàlisi de les variables hidrodinàmiques de flotació: consistència de flotació (c), velocitat d'agitació durant la flotació (N) i cabal d'aire aplicat (q), s'aconsegueix la seva optimització dins el rang de treball permès al laboratori. Valors elevats tant de la velocitat d'agitació com del cabal d'aire aplicat durant la flotació permeten eliminar majors quantitats de tinta. La consistència de flotació assoleix valors òptims depenent de les condicions de flux dins la cel·la de flotació. Les metodologies d'anàlisi emprades permeten obtenir diferents factors de destintabilitat. Entre aquests factors existeix una correlació important (determinada pels coeficients de correlació de Pearson) que permet assegurar la utilització de la blancor com a paràmetre fonamental en l'anàlisi del destintatge de papers vells, sempre i quan es complementi amb anàlisis d'imatge o bé amb anàlisi de la concentració efectiva de tinta residual. S'aconsegueixen expressions empíriques tipus exponencial que relacionen aquests factors de destintabilitat amb les variables experimentals. L' estudi de les cinètiques de flotació permet calcular les constants cinètiques (kBlancor, kERIC, kSupimp) en funció de les variables experimentals, obtenint un model empíric de flotació que relacionant-lo amb els paràmetres microscòpics que afecten realment l'eliminació de partícules de tinta, deriva en un model fonamental molt més difícil d'interpretar. Mitjançant l'estudi d'aquestes cinètiques separades per classes, també s'aconsegueix determinar que l'eficàcia d'eliminació de partícules de tinta és màxima si el seu diàmetre equivalent és superior a 50 μm. Les partícules amb diàmetres equivalents inferiors a 15 μm no són eliminades en les condicions de flotació analitzades. Es pot dir que és físicament impossible eliminar partícules de tinta de diàmetres molt diferents amb la mateixa eficiència i sota les mateixes condicions de treball. El rendiment del procés analitzat en funció de l'eliminació de sòlids per l'etapa de flotació no ha presentat relacions significatives amb cap de les variables experimentals analitzades. Únicament es pot concloure que addicionar quantitats elevades de silicat sòdic provoca una disminució tant de sòlids com de matèria inorgànica presents en les escumes de flotació.

Characteristic magnetic field and speed properties of interplanetary coronal mass ejections and their sheath regions

Prediction of the solar wind conditions in near-Earth space, arising from both quasi-steady and transient structures, is essential for space weather forecasting. To achieve forecast lead times of a day or more, such predictions must be made on the basis of remote solar observations. A number of empirical prediction schemes have been proposed to forecast the transit time and speed of coronal mass ejections (CMEs) at 1 AU. However, the current lack of magnetic field measurements in the corona severely limits our ability to forecast the 1 AU magnetic field strengths resulting from interplanetary CMEs (ICMEs). In this study we investigate the relation between the characteristic magnetic field strengths and speeds of both magnetic cloud and noncloud ICMEs at 1 AU. Correlation between field and speed is found to be significant only in the sheath region ahead of magnetic clouds, not within the clouds themselves. The lack of such a relation in the sheaths ahead of noncloud ICMEs is consistent with such ICMEs being skimming encounters of magnetic clouds, though other explanations are also put forward. Linear fits to the radial speed profiles of ejecta reveal that faster-traveling ICMEs are also expanding more at 1 AU. We combine these empirical relations to form a prediction scheme for the magnetic field strength in the sheaths ahead of magnetic clouds and also suggest a method for predicting the radial speed profile through an ICME on the basis of upstream measurements.

Designs for an adaptive tuned vibration absorber with variable shape stiffness element

An adaptive tuned vibration absorber (ATVA) with a smart variable stiffness element is capable of retuning itself in response to a time-varying excitation frequency., enabling effective vibration control over a range of frequencies. This paper discusses novel methods of achieving variable stiffness in an ATVA by changing shape, as inspired by biological paradigms. It is shown that considerable variation in the tuned frequency can be achieved by actuating a shape change, provided that this is within the limits of the actuator. A feasible design for such an ATVA is one in which the device offers low resistance to the required shape change actuation while not being restricted to low values of the effective stiffness of the vibration absorber. Three such original designs are identified: (i) A pinned-pinned arch beam with fixed profile of slight curvature and variable preload through an adjustable natural curvature; (ii) a vibration absorber with a stiffness element formed from parallel curved beams of adjustable curvature vibrating longitudinally; (iii) a vibration absorber with a variable geometry linkage as stiffness element. The experimental results from demonstrators based on two of these designs show good correlation with the theory.

Variable step LMS algorithm using the accumulated instantaneous error concept

The convergence speed of the standard Least Mean Square adaptive array may be degraded in mobile communication environments. Different conventional variable step size LMS algorithms were proposed to enhance the convergence speed while maintaining low steady state error. In this paper, a new variable step LMS algorithm, using the accumulated instantaneous error concept is proposed. In the proposed algorithm, the accumulated instantaneous error is used to update the step size parameter of standard LMS is varied. Simulation results show that the proposed algorithm is simpler and yields better performance than conventional variable step LMS.

Multivariable cluster analysis for high-speed industrial machinery

The overall operation and internal complexity of a particular production machinery can be depicted in terms of clusters of multidimensional points which describe the process states, the value in each point dimension representing a measured variable from the machinery. The paper describes a new cluster analysis technique for use with manufacturing processes, to illustrate how machine behaviour can be categorised and how regions of good and poor machine behaviour can be identified. The cluster algorithm presented is the novel mean-tracking algorithm, capable of locating N-dimensional clusters in a large data space in which a considerable amount of noise is present. Implementation of the algorithm on a real-world high-speed machinery application is described, with clusters being formed from machinery data to indicate machinery error regions and error-free regions. This analysis is seen to provide a promising step ahead in the field of multivariable control of manufacturing systems.

Default perception of high-speed motion

When human observers are exposed to even slight motion signals followed by brief visual transients—stimuli containing no detectable coherent motion signals—they perceive large and salient illusory jumps. This novel effect, which we call “high phi”, challenges well-entrenched assumptions about the perception of motion, namely the minimal-motion principle and the breakdown of coherent motion perception with steps above an upper limit. Our experiments with transients such as texture randomization or contrast reversal show that the magnitude of the jump depends on spatial frequency and transient duration, but not on the speed of the inducing motion signals, and the direction of the jump depends on the duration of the inducer. Jump magnitude is robust across jump directions and different types of transient. In addition, when a texture is actually displaced by a large step beyond dmax, a breakdown of coherent motion perception is expected, but in the presence of an inducer observers again perceive coherent displacements at or just above dmax. In sum, across a large variety of stimuli, we find that when incoherent motion noise is preceded by a small bias, instead of perceiving little or no motion, as suggested by the minimal-motion principle, observers perceive jumps whose amplitude closely follows their own dmax limits.

Estudo ergonômico do posto de atividade discente em instituição de ensino superior

This research carried through an ergonomic study of the rank of learning activity of a IES, was applied a questionnaire with ergonomic pointers structuralized in scale to intervalar of semantic differential of 0 the 10, in 290 pupils with ages between 18 and 52 years distributed for 5 courses in 9 classrooms, the sample was of the simple random probabilist type. The used statistical techniques had been the descriptive analysis and the analysis of clusters through statistica software 5,0 considering p £ 0,0500. Involving the following 0 variable: Layout; Colors; Acoustics; Illumination; Temperature; Position; Didactic furniture, and Equipment. The gotten results point to consider that the layout of the rooms, the perception of acoustic comfort, the position of the pupils and the furniture of the searched classrooms had been the condicionantes that had been more distinguished negative how much to the perception of comfort of the user. The the 91,5 NPS varied of 57,9 dB(A) values above of recommended for classrooms in accordance with NBR 10152; NR 15; NR 17; It would carry nº 3214/1978, of the Ministry of the Work and searched literature. The Illumination registered interval of 139 the 966 Lux, values are of the limits of interval recommended for classrooms according to NBR 5413 and NR 17. The thermal temperature registered interval of 24° 25,9ºC; URA 41,6 79.1% and the 0.1 air speed 1,0 m/s, values above of recommended for classrooms according to NBR the 6401 and NR 17. The research still suggests that it would have associations between pains in the body the positions of the pupils and the furniture of the classrooms. The results suggest research especially add for the conditions thermal and acoustics of the classrooms

Joint (X)over-bar and R charts with variable sample sizes and sampling intervals

Recent studies have shown that the (X) over bar chart with variable sampling intervals (VSI) and/or with variable sample sizes (VSS) detects process shifts faster than the traditional (X) over bar chart. This article extends these studies for processes that are monitored by both the (X) over bar and R charts. A Markov chain model is used to determine the properties of the joint (X) over bar and R charts with variable sample sizes and sampling intervals (VSSI). The VSSI scheme improves the joint (X) over bar and R control chart performance in terms of the speed with which shifts in the process mean and/or variance are detected.