Developing of the Variable Speed Drive -control in simulated parallel pumping systems

This thesis presents briefly the basic operation and use of centrifugal pumps and parallel pumping applications. The characteristics of parallel pumping applications are compared to circuitry, in order to search analogy between these technical fields. The purpose of studying circuitry is to find out if common software tools for solving circuit performance could be used to observe parallel pumping applications. The empirical part of the thesis introduces a simulation environment for parallel pumping systems, which is based on circuit components of Matlab Simulink —software. The created simulation environment ensures the observation of variable speed controlled parallel pumping systems in case of different controlling methods. The introduced simulation environment was evaluated by building a simulation model for actual parallel pumping system at Lappeenranta University of Technology. The simulated performance of the parallel pumps was compared to measured values of the actual system. The gathered information shows, that if the initial data of the system and pump perfonnance is adequate, the circuitry based simulation environment can be exploited to observe parallel pumping systems. The introduced simulation environment can represent the actual operation of parallel pumps in reasonably accuracy. There by the circuitry based simulation can be used as a researching tool to develop new controlling ways for parallel pumps.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

Improved glycemic control by acarbose therapy in hypertensive diabetic patients: effects on blood pressure and hormonal parameters

A double-blind, randomized, placebo-controlled study was carried out on 44 hypertensive type 2 diabetic subjects previously treated by diet associated or not with sulfonylurea to assess the effects of acarbose-induced glycemic control on blood pressure (BP) and hormonal parameters. Before randomization and after a 22-week treatment period (100 to 300 mg/day), the subjects were submitted to a standard meal test and to 24-h ambulatory BP monitoring (ABPM) and had plasma glucose, glycosylated hemoglobin, lipid profile, insulin, proinsulin and leptin levels determined. Weight loss was found only in the acarbose-treated group (75.1 ± 11.6 to 73.1 ± 11.6 kg, P<0.01). Glycosylated hemoglobin decreased only in the acarbose group (6.4 ± 1.7 to 5.6 ± 1.9%, P<0.05). Fasting proinsulin decreased only in the acarbose group (23.4 ± 19.3 to 14.3 ± 13.6 pmol/l, P<0.05), while leptin decreased in both (placebo group: 26.3 ± 6.1 to 23.3 ± 9.4 and acarbose group: 25.0 ± 5.5 to 22.7 ± 7.9 ng/ml, P<0.05). When the subset of acarbose-treated patients who improved glycemic control was considered, significant reductions in diurnal systolic, diastolic and mean BP (102.3 ± 6.0 to 99.0 ± 6.6 mmHg, P<0.05) were found. Acarbose monotherapy or combined with sulfonylurea was effective in improving glycemic control in hypertensive diabetic patients. Acarbose-induced improvement in metabolic control may reduce BP in these patients. Our data did not suggest a direct action of acarbose on insulin resistance or leptin levels.

Aplicación del control estadístico a la variable crítica temperatura en una empresa acerera.

Tesis (Master en Administración y de Negocios con Especialidad en Producción y Calidad) UANL, 2009.

A regime-dependent balanced control variable based on potential vorticity

In this paper it is argued that rotational wind is not the best choice of leading control variable for variational data assimilation, and an alternative is suggested and tested. A rotational wind parameter is used in most global variational assimilation systems as a pragmatic way of approximately representing the balanced component of the assimilation increments. In effect, rotational wind is treated as a proxy for potential vorticity, but one that it is potentially not a good choice in flow regimes characterised by small Burger number. This paper reports on an alternative set of control variables which are based around potential vorticity. This gives rise to a new formulation of the background error covariances for the Met Office's variational assimilation system, which leads to flow dependency. It uses similar balance relationships to traditional schemes, but recognises the existence of unbalanced rotational wind which is used with a new anti-balance relationship. The new scheme is described and its performance is evaluated and compared to a traditional scheme using a sample of diagnostics.

Vortex dynamics in mesoscopic superconducting square of variable surface

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Double sampling (x)over-bar control chart for a first-order autoregressive moving average process model

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Experimental Active Vibration Control in Truss Structures Considering Uncertainties in System Parameters

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Economic design of (X)over-bar and R charts under Weibull shock models

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A phase-shifting control for variable frequency multi-cells interleaved boost pre-regulator based on FPGA device

In this paper were investigated phase-shift control strategies applied to a four cells interleaved high input-power-factor pre-regulator boost rectifier, operating in critical conduction mode, using a non-dissipative commutation cells and frequency modulation. The digital control has been developed using a hardware description language (VHDL) and implemented using the XC2S200E-SpartanII-E/Xilinx FPGA, performing a true critical conduction operation mode for a generic number of interleaved cells. Experimental results are presented, in order to verify the feasibility and performance of the proposed digital control, through the use of a Xilinx FPGA device.

X charts with supplementary samples to control the mean and variance

A standard X chart for controlling a process takes regular individual observations, for instance every half hour. This article proposes a modification of the X chart that allows one to take supplementary samples. The supplementary sample is taken (and the (X) over bar and R values computed) when the current value of X falls outside the control limits. With the supplementary sample, the signal of out-of-control is given by an (X) over bar value outside the (X) over bar chart's control limits or an R value outside the R chart's control limit. The proposed chart is designed to hold the supplementary sample frequency, during the in-control period, as low as 5% or less. In this context, the practitioner might prefer to verify an out-of-control condition by simply comparing the (X) over bar and R values with the control limits. In other words, without plotting the (X) over bar and R points. The X chart with supplementary samples has two major advantages when compared with the standard (X) over bar and A charts: (a) the user will be plotting X values instead of (X) over bar and R values; (b) the shifts in the process mean and/or changes in the process variance are detected faster.

Joint conomic design of (x)over-bar and R charts under Weibull shock models

This paper deals with the joint economic design of (x) over bar and R charts when the occurrence times of assignable causes follow Weibull distributions with increasing failure rates. The variable quality characteristic is assumed to be normally distributed and the process is subject to two independent assignable causes (such as tool wear-out, overheating, or vibration). One cause changes the process mean and the other changes the process variance. However, the occurrence of one kind of assignable cause does not preclude the occurrence of the other. A cost model is developed and a non-uniform sampling interval scheme is adopted. A two-step search procedure is employed to determine the optimum design parameters. Finally, a sensitivity analysis of the model is conducted, and the cost savings associated with the use of non-uniform sampling intervals instead of constant sampling intervals are evaluated.

Joint (X)over-bar and R charts with two-stage samplings

When joint (X) over bar and R charts are in use, samples of fixed size are regularly taken from the process, and their means and ranges are plotted on the (X) over bar and R charts, respectively. In this article, joint (X) over bar and R charts have been used for monitoring continuous production processes. The sampling is performed, in two stages. During the first stage, one item of the sample is inspected and, depending on the result, the sampling is interrupted if the process is found to be in control; otherwise, it goes on to the second stage, where the remaining sample items are inspected. The two-stage sampling procedure speeds up the detection of process disturbances. The proposed joint (X) over bar and R charts are easier to administer and are more efficient than the joint (X) over bar and R charts with variable sample size where the quality characteristic of interest can be evaluated either by attribute or variable. Copyright (C) 2004 John Wiley Sons, Ltd.

Economic design of two-stage (X)over-bar charts: the Markov chain approach

When the (X) over bar chart is in use, samples are regularly taken from the process, and their means are plotted on the chart. In some cases, it is too expensive to obtain the X values, but not the values of a correlated variable Y. This paper presents a model for the economic design of a two-stage control chart, that is. a control chart based on both performance (X) and surrogate (Y) variables. The process is monitored by the surrogate variable until it signals an out-of-control behavior, and then a switch is made to the (X) over bar chart. The (X) over bar chart is built with central, warning. and action regions. If an X sample mean falls in the central region, the process surveillance returns to the (Y) over bar chart. Otherwise. The process remains under the (X) over bar chart's surveillance until an (X) over bar sample mean falls outside the control limits. The search for an assignable cause is undertaken when the performance variable signals an out-of-control behavior. In this way, the two variables, are used in an alternating fashion. The assumption of an exponential distribution to describe the length of time the process remains in control allows the application of the Markov chain approach for developing the cost function. A study is performed to examine the economic advantages of using performance and surrogate variables. (C) 2003 Elsevier B.V. All rights reserved.